Search Documents

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"The purpose of the study was to investigate the feasibility of SiC reduction of low-grade concentrates from Lonmin’s Rowland and Easterns operations with respect to metal fall and PGM recovery. These concentrates are rich in SiO2 and MgO with low concentrations of chalcopyrite and Cr2O3. Pd is the most abundant of the PGMs. SiC reduction of samples was conducted at 1600? with 2.5-3.5 kg SiC per 100 kg concentrate.PGM recoveries for Easterns concentrate were better than for Rowland. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered with 3.5 kg SiC per 100 kg concentrate. SEM of slag samples showed little entrainment of metallic prills compared to Rowland samples. This was attributed to the relatively higher melt viscosities of the Rowland concentrate. In order to decrease slag viscosity and to enhance PGM recovery, the FeO content of the Easterns concentrate was increased with the addition of 10 kg converter slag per 100 kg concentrate. Ir and Pd recoveries were increased to about 95%, while Pt recovery was around 70%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and converter slag is proposed. Carbothermic reduction of the optimum charge was also compared to SiC reduction. Carbothermic reduction yielded a marginally higher metal fall; however, the calculated gas emissions and energy requirements were higher than for SiC reduction."

Jan 1, 2015

By P. Varona, L. Lorig, M. Board, E. Chacon

Geomechanical factors at the mine are important and will become even more relevant as the pit expands and deepens. To address these demands a team was assembled to collect geomechanical information and perform numerical analysis. The west wall is the largest and flattest of all the design sectors in the pit and rigorous studies were carried out on this wall. The wall behaviour is controlled mainly by a set of steeply dipping joints within the slope in the Fortuna Granodiorite and a weak zone, the Zona Plastica, that extends vertically near the pit bottom. These features lead to large toppling displacements in the upper portions of the wall. Two numerical models were used to reproduce the general features of failure observed in the wall. The modelling indicated that a toppling mode of failure results from shear on the steeply dipping joints. The toppling leads to slumping or landslides whereby the west wall flows slowly downslope as the Zona Plastica compresses

Apr 1, 1996

By M A. Tuck

The dominant heat loads in a deep underground mine are the surrounding rock mass, autocompression and machinery. In addition heat can be contributed to by other sources. Many block cave, sublevel cave operations and coalmines utilise conveyors to transport broken rock out of mine, in some cases completely, in others in combination with other forms of transport. This broken rock can be loaded onto the conveyor at virgin rock temperature and can represent a major heat input to the ventilation airflow as it is transported out of the mine. The purpose of this paper is to review established knowledge regarding heat flow, from conveyed rock to determine the main factors influencing the heat flow and to develop a methodology for predicting heat flow from caved rock. The paper concludes with suggestions for further research in the area of conveyed rock heat transfer.CITATION:Tuck, T A, 2017. Accurately estimating heat load from conveyed rock, in Proceedings Australian Mine Vent Conference 2017, pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By H. M. Lawrence

"Florida, the State that supplied 82 per cent of the phosphate rock sold in the United. States in 19284, has two producing areas - the hard-rock and the land pebble districts. Production of the hard-rock field, decreasing importance in recent years, is now confined to mines near Dunnellon, in Marion and. Citrus Counties. The land-pebble district, with a production of almost 80 per coat of the nation's requirements, is located, in Polk and Hillsborough Counties. In the land-pebble area the phosphate deposits - probably Pliocene in age, derived by marine action from underlying, older, phosphate-bearing formations - consist of beds of phosphate matrix, covered by practically barren sands and clays. The overburden, ranging in thickness up to 45 feet, is removed by hydraulic methods or by drag-line excavators. The matrix, ordinarily less than 25 feet in thickness, is mined by hydraulicking and is pumped to adjacent washing plants for beneficiation. The dried product of the washing plants is the Florida pebble rock that is sold in foreign as well as domestic markets.The beneficiation of phosphate ores in the land-pebble district of Florida has been largely limited in the past to the recovery of the coarser pebbles. By washing and screening the crude matrix a separation is effected at about 20 mesh (0.033 inch). The coarser material is the phosphate-rock product of the plant and the finer material is discarded. The amenability of the washer- rejects to treatment by other processes is being investigated. Of methods that may have some application to the treatment of the low-grade phosphatic sands that comprise the greater portion of the washer-rejects, gravity concentration has received some study.Laboratory experiments to determine the amenability of phosphate sands to gravity methods of concentration were first performed in October, 1927. Later, in the winter of 1928-1929, a further series of teats was made,. In these later tests phosphatic sands were concentrated by hydraulic classification, and. also by hydraulic classification followed by tabling. In these experiments concentrates with an analysis above the minimum grade of commercial phosphate rock (66 per cent bone phosphate of lime - B.P.L.) obtained. The recovery of the phosphate varied but was promising enough to warrant further study. A more comprehensive investigation was therefore outlined. This paper presents the results obtained from an investigation, of classification and tabling of phosphatic sands recently completed by the United States Bureau of Mines Su cooperation with certain Florida phosphate companies, the Missouri School of Mines and Metallurgy, and the University of Alabama."

Jul 1, 1930

By Robert B. Parsons

"Investors in flow-through shares are going to need an expanded road map to find their way through a growing maze of tax rules affecting such shares. At the end of 1985, no fewer than three new sets of important tax amendments were tabled which could have a significant effect on flow-through share issues. This proposed legislation is discussed this month in Tax Notes.IntroductionIn a flurry of legislative activity at the end of 1985, the federal government tabled legislation which includes the introduction of new rules which will have a notable effect on investors in flow-through shares and on companies that issue such shares.First, on November 26, 1985, Bill C-84, the legislation to implement most of the changes announced in the May budget, was introduced in Parliament. This legislation includes the rules for the $500,000 capital gains exemption, a matter of considerable interest to flow through share investors.Next, on December 2, 1985, the government tabled a Notice of Ways and Means Motion which would extend the time horizon for spending flow-through share funds to include the 60-day period following the calendar year. But all news was not good news. On December 4 the government released its proposals for a minimum personal income tax, which would include rules that would catch an investor's CEE expenses and capital gains."

Jan 1, 1986

By M. Moinpour, Y. K. Rao

The catalysed direct reduction of copper sulphide with carbon and lime was investigated in the range 850-1000 degrees C using Cu2S-CaO-C and Cu2S-4CaO-4C reaction mixtures. The effects of the catalytic additives K2CO3, Li2CO3, Na2CO3, NaF, Na2SO3 and the ternary eutectic (K,Li,Na)2CO3 were determined. Potassium carbonate, sodium fluoride and the ternary appear to be the most effective catalysts for the direct reduction process. The rate enhancement of the catalysed carbothermic reduction of copper sulphide in the presence of lime was explained in terms of the catalysis of the Boudouard reaction

Jul 1, 1991

By W. F. Boericke

AT Kellogg, Idaho, J. Fred Johnson is driving the 5000.-ft Hooper Tunnel under contract for the Bunker Hill & Sullivan Mining Co. This was visited by a group of engineers during the recent meeting of the A. I. M. E. at Spokane, who were impressed with several features of the work. An excellent record of advance is being made by the contractor, over 47 ft. being driven in 3 days during October, and 223 ft. advanced in 29 shifts. The size of the tunnel is 8 by 9 ft. The ground is Wallace quartzite and, save for the first hundred feet, stands well and does not require timbering. The grade is held uniformly at 0.5 per cent. Two shifts are employed, with two sets of machine men to the shift. Ingersoll-Rand S-70 drills are used. each machine being set up independently in the heading; 26-30 holes are drilled to the round; using 1 1/4: in. round hollow drill steel. A 7-hole cut is required, and these holes are blasted simultaneously, using 60 per cent gelatine, 12 sticks to the hole. Instantaneous and fire delays of electric detonators are used for the complete round. A feature of the drilling is the use of long carriage drills, necessitating fewer changes of steel, and more time spent on drilling, with less time consumed taking steel back and forth from the face. Of course, this means better blacksmithing so that the drill steel shall stand up for the added footage.

Jan 1, 1930

By D. Harrington

"One of the underlying reasons for the establishment of the United States Bureau of Mines was the desire to promote greater safety in the mining and allied industries. Safety continues to be an important feature in the work of the bureau, and during the fiscal year 1929-30 the Bureau of Mines allotted $387,510 to the safety division out of a total appropriation of $2,249,670 (other than for helium).The safety division personnel consists of 22 engineers, 2 mine safety commissioners, 3 senior foreman miners, 18 foreman miners, 16 first-aid miners, 16 clerks, 10 cooks, and 3 laborers, a total of 90 persons. These safety workers are distributed through the 10 districts into which the United States has been divided for administration purposes. During the year 3 engineers, 1 senior foreman miner, 4 foreman miners, and 4 first-aid miners left the service. In general these men left the service to take up more lucrative positions.The 10 all-steel mine-rescue cars have headquarters as follows: Car 1, Reno, Nev.; Car 2, Raton, N. Mex.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa. There is also a mine-rescue car with headquarters at Juneau, Alaska. In addition, there have been established 11 mine rescue stations as follows: Birmingham, Ala.; Berkeley, Calif.; Seattle, Wash.; Evansville, Ind.; Jellico, Tenn.; McAlester, Okla.; Norton, Va.; Vincennes, Ind.; Wilkes Barre, Pa.; Salt, Lake City, Utah; and Pittsburgh, Pa.Every mine-rescue car and station is fully supplied with equipment and devices for use in case of mine fire or explosion, and at each station is an up-to-date automobile truck. At time of amine disaster the bureau's forces are immediately placed at the disposal of the authorities, State or company, with a view to giving such assistance as may be desired or available.The activities of the safety division at ordinary times are directed largely to securing and disseminating data on safety in mining. Among the numerous studies made, or being made, concerning safety and health in mining are those in connection with the causes and methods of prevention of mine explosions, explosibility of dust and gases, explosives and blasting, haulage, electricity, falls of persons or material, ventilation, dusts, high temperatures, timbering, lighting, machinery, and in fact practically anything which results or may result in acci¬dents of any kind in or around mines."

Nov 1, 1930

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

By Robert Hopler

This article, advocating having employees whose specific job would be to fire blasts in underground coal mines in llinois, was written 5 years prior to the establishment of the U.S. Bureau of Mines, and 2 1/2 years before the worst month in U.S. coal mining history, when 692 miners were killed in three separate explosions in December 1907. Obviously something had to be done to improve safety in the use of explosives, and having dedicated shotfirers was a good first step.

Jan 1, 2006

By Robert E. McIvor

"The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out.The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, “Circuit Classification System Efficiency” (CSE), is the fraction of “coarse” material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of “fines” or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable target CSE for any given circuit can be estimated, for example, by referring to a plant data base of CSE’s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE.This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “Circuit Classification System Efficiency” (or CSE, McIvor, 1988a), and subsequently the discovery of the Functional Performance Equation (McIvor, 1988b; McIvor et al, 1992). The CSE is the fraction or percentage of “coarse” (usually in reference to the plus P80) size material inside the mill, versus “fines” or product size material finer than the circuit P80. It can be readily calculated by taking the average of the percentage of said coarse material in the mill feed and mill discharge streams. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, for which the derivation has often been presented (e.g. McIvor, 2006)."

Jan 1, 2011

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dike intrudes Ordovician-Silurian metapelite and quartzite. These metasedimentary rocks have undergone three phases of folding: a first phase of recumbent folds (F1), a second phase (F2) of northerly-trending inclined folds with a prominent crenulation cleavage, and a third phase (F3) of steeply plunging folds. The granite porphyry dike has a thickness of up to 40 m and intrudes thin lamprophyre dikes along its contacts. Deflection of the crenulation cleavage around the granite dike, shearing within the dike and its sinuous outcrop pattern indicate that the granite dike has been deformed during F2 and F3. The granite has been hydrothermally altered, with a first stage of magnetite-ankerite alteration. This first stage is cut by a second stage of quartz-pyrite veins and a third stage of sulphide, quartz and ankerite veins, accompanied by pervasive silicification represented by quartz-perthite-albite-rutile¦pyrite-ankerite-sericite assemblages. Lamprophyre is altered to an ankerite-chlorite-sericite assemblage. The sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite. The altered granite and the veins have been deformed and recrystallised. The competent sulphide minerals pyrite and arsenopyrite are fractured and brecciated, with fractures locally filled by galena, a ductile sulphide mineral. Vein quartz shows local cataclastic and mortar textures and develops pressure shadows around arsenopyrite. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre. These features together with the style of veining and the sulphide mineralogy indicate that the mineralisation was formed from a magmatichydrothermal fluid that was sourced from the granite. Oxygen, carbon and sulphur isotope values of the vein minerals (quartz, ankerite and sulphides) are also consistent with a magmatic source.

Jan 1, 2003

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965

That electricity is an important and valuable agent, the limit of whose capacity for utilisation is as yet unknown, is a truism; although enormous advances have been made, the possible developments are yet greater. Mining, along with other industries, shares already to a large extent in the practical utilisation of this agent. Electrical engineers have been employed for several years past in developing and applying electricity to all classes of machinery, and for every purpose where power is required and in no instance, that the writer is aware of, has its use been curtailed in favour of any other agency now known, while extensions are continually made. The first modern electric motor was shown at the Vienna Exhibition of 1873, and it was used to work a pump through a mile length of cable but it was not before 1878, that an electric motor was put into daily commercial use by Messrs. Chretian and Felix to work a beet sugar hoist. This early plant effected a saving of 40 % as compared with hand work.In 1879, the first Electric Railway was constructed for the Berlin Exhibition, and in the same year, Mr. T. A. Edison was running an experimental line at Menlo Park. The first electric line opened for the public, was constructed by Siemens and Halske, in 1881, at Lichtenfelde, and was 11 miles in length.

By J. Crummy, I. K. Anderson, A. J. Hall, R. S. Haszeldine

Bedrock gold mineralisation has been located in association with an extensive float train 25 km west of known alluvial gold. It is in the form of open, matrix-supported breccias comprising pyritic quartz/sericite clasts in a vuggy, cherty chalcedonic and crystalline quartz matrix. Fluid inclusions in pyritic clasts indicate trapping temperatures for gold mineralising hydrothermal fluid of 170-240 degrees C. This mineralisation could represent the upper part of a feeder zone to an exhalative hydrothermal system. It is possible that other high-level feeder zones could be preserved elsewhere in the area. Deep weathering of such a system could provide a source for the alluvial gold localities near Helmsdale. It is suggested that east and central Sutherland presents good prospects for exhalative epithermal gold mineralisation and the associated feeder zones

Jun 19, 1905

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

The paper discusses the special mixing requirements for Metallurgical Plant Design and outlines the problems associated with the agitation in Mineral Processing Industry today. It also covers new applications such as state of the art large leach tanks and backfill for deep mining.

Jan 1, 2004