Search Documents

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By Da Zhao Gu

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

By W. S. Steinberg

Keywords: Pyrometallurgy, furnace, open slag bath, Evraz, Highveld In 1963, the full-scale engineering study for the development of an Iron, Steel, and Vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steel works that produced steel and vanadium-bearing slag by using a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for pre-reduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to Open Slag Bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of a higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

By M. Ghoreychi, X. Daupley

ABSTRACT: The paper is devoted to two major aspects related to the abandonment of salt mines: 1)- Long-term risk associated with the mechanical instability of surface and its consequences for public security and properties. 2)- Long term dissolution and transport of salt resulting from its communication with groundwater. Basic characteristic features of salt deposits and mining methods are presented through the studies already undertaken on French mines. This analysis allows to identify major hazards encountered in different traditional salt mines and solution-mining cavities. In particular, the role of overburden (presence and thickness of salt layer in exploitation roof, presence of clayey rocks or hard rocks e.g. dolomite or anhydrite), presence of water-bearing strata and possibly natural brine levels, discontinuities, etc. are discussed. In the second part, the main features of mechanical behaviour of salt (creep, damage) as well as transfer processes of this material are presented. The influence of these aspects on the long term evolution of abandoned salt mines is then analysed. KEY WORDS: exploitation, abandonment, salt, mechanical, stability, transport, solution, brine. ZUSAMMENFASSUNG: Der Artikel bezieht sich auf zwei bedeutende Aspekte beim Salzabbau: 1)-Das langsfristige Risiko zur Bodenoberflächeunbeständigkeit und sein Einfluss über Mensch= und Gütersicherheit. 2)-Die langsfristige Auflösung und Beförderung des Salz beruhen sich auf Studien über französiche Bergbauen. Diese Analyse emöglicht es, die bedeutendesten Risiken in verschiedenen Salzgruben zu identifizieren, bzw. Traditionellen oder durch Auflösung abgebauten. Insbesondere wird die Rolle des Deckgebirges (Vorhandensein und Dicke von Salzschicht am Dach des Grube, Beisein von Tanlager oder hartem Gestein wie Bitterkalk oder Anhydrid), Beisein von wasserhaltigem Boden und/oder gesalzenen Wasserflächen, Trennflächen, usw… erötert. Im zweiten Teil werden die haupsächlichen Eigenschaften des Salzverhaltens (Kriechen und Beschädigung) beschrieben. Ihr Einfluss über das Verhalten von stillgelegten Bergwerken lässt sich analysieren. SCHLÜSSELWÖRTER: Bergwerksbetrieb, Stilllegung, Mechanik, Beständigkeit, Ausbreitung, Aussolung, Solewasser. RESUME: L’article est consacré à deux aspects majeurs liés à l’abandon d’exploitations de sel : 1)- Le risque d’une instabilité à long terme de la surface du sol et son incidence sur la sécurité des personnes et des biens. 2)- La dissolution à long terme et le transport de sel sous l’effet d’une communication avec des eaux souterraines. Les principales caractéristiques de gisements et d’exploitations de sel sont présentées en s’appuyant sur les études antérieures réalisées sur les exploitations en France. Cette analyse permet d’identifier les risques majeurs rencontrés dans différentes mines de sel traditionnelles ou exploitées par dissolution. En particulier, le rôle du recouvrement (présence et épaisseur d’un banc de sel au toit de l’exploitation, présence de terrains argileux ou de roches dures telles que la dolomie ou de l’anhydrite), présence de terrains aquifères ou de nappes salées éventuelles, discontinuités, etc. sont discutées. Dans la deuxième partie, les principaux traits du comportement mécanique du sel (fluage, endommagement) ainsi que les processus de transport de ce matériau sont présentés. L’influence de ces aspects sur le comportement à long terme d’exploitations abandonnées de sel est ensuite analysée. MOTS CLES: exploitation, abandon, mécanique, sel, stabilité, transport, dissolution, saumure.

Jan 1, 2003

Behaviour of Bubble Clusters in a Turbulent Flow

Sep 13, 2010

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By R. Heersink, C. H. Wells

Innovations in communications and real-time information systems are providing industry opportunities to improve profitability. Real-time operating data is collected from equipment across a site or even several sites into a central server for secure PC and PDA-based Internet access. This paper includes discussion of how operating staff can use wireless devices to see equipment and processing data from anywhere throughout the mines and concentrators, and how management can view results from multiple mines, all in real time. Additional opportunities enabled through the remote access by equipment vendors or mining consultants is also presented, as well as an overview of typical benefits and current installations.

Jan 1, 2002

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005

By Wilfred G. Comeao

Close-in blasting occurs every time the use o f explosives for excavation or demolition requires the surpassing of the commonly accepted cosmetic damage criteriain order to arrive at reasonable and practical explosive weights per delay. One of the many effective blast design procedures consists in establishing a reasonable charge weight per delay with respect to scale, geometry, costs, requirements and constraints of the project. Once this reasonable charge weight per delay is determined, it’s environmental effects have to be estimated with respect to the surroundings.

Jan 1, 1991

By Juan Garcia de Blas

O presente trabalho aborda o desenvolvimento de liga titânio-nióbio obtida por metalurgia do pó no qual foi introduzida uma operação de extrusão angular em canal (Equal Channel Angular Pressing - ECAP) com o propósito de promover uma consolidação que favorecesse a homogeneização na etapa posterior de sinterização. Após o processamento o material foi caracterizado por microscopia ótica e microscopia eletrônica de varredura (MEV/EDS). Os resultados preliminares indicaram a importância da redução do tamanho das partículas de nióbio.

Aug 17, 2017

By R. R. Joseph, K. A. Gschneidner

The solid solubility of magnesium in the close-packed modifications of lanthanum, cerium, praseodymium, neodymium, gadolinium, dysprosium, and lutetium was determined from approximately 250°C to the eutectoid temperature by the X-ray parametric technique. The maximum solubility at the eutectoid temperature was found to be 9.4 at. pet in La, 8.2 in Ce, 9.2 in Pr, 8.2 in Nd, 14.1 in Gd, 13.5 in Dy, and 11.5 in Lu. The solubility when compared at a homologous temperature was found to increase in a smooth manner with decreasing size factor from lanthanum to lutetium. It was found that the apparent atomic radius of magnesium when dissolved in the lanthanide solvent was constant and could be accounted for by consideration of several models dealing with departures from Vegard's law. The eutectoid temperatures for the lanthanide-rich La-Mg, Ce-Mg, and Nd-Mg systems were found to be 544", 505°, and 551°c, respectively. A study of the solid solubility of magnesium in the lanthanide metals was initiated because the valency and electron egativity difference are essentially constant and favorable for solid-solution formation, and thus one could examine the effect of size on terminal solid solutions. The size factors based on metal radii range from 14.6 pet for lanthanum to 7.5 pet for lutetium. Since the electronegativity difference is small, 0.06 unit or less, application of the Hume-~othery' and Darken and Gurry2 criteria for solid-solution formation indicates that the solubility of magnesium would be expected to be small for lanthanum (between 5 and 10 at. pet) and to increase as we proceed along the lanthanide series. A search of the literature revealed no data on the solubility of magnesium in the lanthanide metals except for the solubility of magnesium in cerium at 450oCA typical phase diagram for the lanthanide-rich end of the lanthanide-magnesium phase diagram is shown in Fig. 1. EXPERIMENTAL PROCEDURES Preparation of Alloys. The lanthanide metals used in the preparation of alloys for this investigation were prepared from the corresponding fluoride by metallothermic reduction techniques previously described by Daane.4 The chemical analyses of the metals used are listed in Table I.

Jan 1, 1965

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013