Search Documents

By H. C. Verakis, M. L. Harris, M. J. Sapko, K. L. Cashdollar

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

By Jean-Marc Lulin

"Depuis 1906, pres de 130 gisements ont ere decouverts dans la inture archeenne polymetallique (Cu, Zn, Au, Ag) du nord-ouest becois. Une etude regionale du developpement du potentiel inier est presentee puis detaillee pour quatre secteurs: RouynDranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des parametres suivants: temps, ethodes de decouverte, profondeur des gisements et poids metal. ~~ courbes cumulatives illustrant le nombre de gisements decouverts fonction du temps montrent une forme generale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de ~ouverte. Initiation, realisation et stabilisation des cycles de decourte sont ainsi mis en evidence. Deux ""bourns miniers"", de 1922 a ~5 et de 1955 a 1965, rassemblent 72 % des mines identijiees squ' a present.La plupart des mines sont trouvees en subsurface: 90% ont leur fmet entre 0 et 100 metres de profondeur dont 70 % entre 0 et 10 etres. Dans le temps, il y ad' abord recolte par prospection puis par fphysique et enjin, developpement progressif du potentiel en proeur avec des methodes composites. Environ 80% du poids metal extrait de 4 camps miniers, couvrant 8% de Ia surface regionale quelques gros gisements dominent /a production.Ces donnees permettent de proposer une nouvelle approche pour lysed' une region miniere:La distribution de Ia profondeur des gisements en fonction du temps est indicatricede /amaturite d' uncampminieret peut servir a evaluer son potentiel residue/.L' analyse des courbes en ""S"" permet d' extrapoler les taux de succes relies aux differentes methodes et met en relief le role crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1990

By Jean-Marc Lulin

"Depuis 1906, près de 130 gisements ont été découverts dans la inture archéenne polymétallique (Cu, Zn, Au, Ag) du nord-ouest québécois. Une étude régionale du développement du potentiel inier est présentée puis détaillée pour quatre secteurs: Rouyn-Dranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des paramètres suivants: temps, méthodes de découverte, profondeur des gisements et poids métal. Les courbes cumulatives illustrant le nombre de gisements découverts fonction du temps montrent une forme générale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de couverte. Initiation, réalisation et stabilisation des cycles de décourté sont ainsi mis en évidence. Deux ""bourns miniers"", de 1922 à 1945 et de 1955 à 1965, rassemblent 72 % des mines identifiées sqú à présent.La plupart des mines sont trouvées en subsurface: 90% ont leur mmet entre 0 et 100 mètres de profondeur dont 70 % entre 0 et 10 êtres. Dans le temps, il y a d' abord récolte par prospection puis par ophysique et enfin, développement progressif du potentiel en proeur avec des méthodes composites. Environ 80% du poids métal extrait de 4 camps miniers, couvrant 8% de Ia surface régionale quelques gros gisements dominent /a production.Ces données permettent de proposer une nouvelle approche pour analyse d' une région minière:La distribution de Ia profondeur des gisements en fonction du temps est indicatrice de la maturité d' un camp minier et peut servir a évaluer son potentiel résiduel.L’analyse des courbes en ""S"" permet d’extrapoler les taux de succès relies aux différentes méthodes et met en relief le rôle crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1989

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Minoru Kawamura, Shinya Tanaka

In Japan, a cartridged emulsion explosive is generally used for tunneling. The workers are compelled to approach the face on charging the explosives into the drill hole with the tamping rod. Therefore, the workers are exposed to the risk of the disaster with the cave-in and the falling rock. The mechanization of the tunnel work has been advancing gradually. Especially, the development of the mechanization for charging work is desired in order to avoid the risk of disaster on workers. Recently, some charging machines such as the bulk emulsion explosives have been evaluated. However, a universal method has not been established yet, because the evaluated machines were not adequately suited from the point of the regulations and the consumption style of explosives.

Jan 1, 2008

By H. Krogerus, P. Jokinen, T. Lintumaa

The energy consumption and recovery of chromium are important economic factors in ferrochrome production. Outokumpu has a lot of experience of the reduction behavior of the sintered pellets in industrial-scale furnaces and also on the grounds of numerous laboratory and pilot-scale investigations. Sintered pellets have shown a superiority over lumpy ore and briquettes made of the same chromite grade. The good performance of the pellets has also resulted in investigations on the reasons for such a performance. In this study, the factors affecting pellet behavior in smelting furnace were investigated. This study is divided into two sections, i.e. the investigations were on the factors affecting solid state reduction and on the factors affecting reduction under melting. These tests were performed by means of thermo gravimetry and by smelting tests. The correlation between the pellet characteristics and reduction behavior was shown and its influence on industrial-scale furnaces was discussed. Factors worth of consideration are for instance, the extent of oxidation during sintering, slag formation and chemistry in respect of molten state reduction, and the grain size of the chromite mineral in the raw material in respect of kinetic reasons (retention time in smelting).

Jan 1, 2007

By Jim Truskoski, Alain Bouchard, Andy Kerr, Germain Labonté, Jim Barrett

"Improving mill grade recovery relationships is always good business. INCO’s Clarabelle Mill has just undergone a $16 million process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as INCO embarks on its second century of operation.INTRODUCTIONIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at INCO’s Clarabelle Mill in Copper Cliff, Ontario.BACKGROUNDThe Clarabelle Mill was built in 1971 on the southern rim of the Sudbury basin. At that time it was one of four mills operated by INCO in the Sudbury area. During the 1970’s, 80’s and 90’s, the need for increased process efficiency, higher levels of sulphur rejection to tails and the concurrent development of high capacity mills and flotation cells, resulted in the consolidation of INCO’s Sudbury area milling operations into a single, expanded facility at Clarabelle."

Jan 1, 2003

By K. Yoo

Cuprous oxide is one of the oldest antifouling agents and also acts as red pigment in these paints. In printed circuit board manufacturing industries, waste etchant contains a substantial amount of copper ion. In the present study, a process was suggested for recovering cuprous oxides from the waste etchant and optimum conditions were investigated to recover the cuprous oxides. The process consists of two steps: in first step, Cu powder is added into wastewater solution, and cupric ions re-duce into cuprous ions (Cu+Cu2+?2Cu+), where cuprous ions precipitate as cuprous chloride; In second step, cuprous oxide is synthesized by adding NaOH into cuprous chloride solution (2CuCl+2NaOH?Cu2O+NaCl+H2O). Optimum conditions were investigated to recover cuprous oxide in the processes. When copper powder was added into wastewater with copper ions, Cu concentration decreased from 15.6% to 2.6% and ORP decreased from 620 mV to -59.9 mV. This result shows that cupric ions reduced into cuprous ions. XRD data indicated that the precipitate was cuprous chloride powder. Using the cuprous chloride recovered and NaOH solution, cuprous oxide was synthesized. To investigate the optimum condition, various NaOH solutions were added into water with CuCl, and then pH, ORP, Cu concentration, Cu contents in precipitates were analysed. XRD data showed that main component of precipitates was cuprous oxide.

Jan 1, 2014

By Peter A. Eshun

This paper studies two methods that account for risks associated with gold mining projects such as mineral risks and country risks. The first method is sensitivity analysis, which investigates the effects of a change in any economic parameter such as operating cost, capital investment, gold price or taxes on the viability of the project. The second method is Monte Carlo Simulation technique, which takes into consideration the simultaneous random variation of the economic parameters on the project's viability. An automated simulation cash flow model has been developed as part of this paper. Sensitivity analysis and the simulation model have been used to investigate the economic viability of the Dokrupe Gold Project (DGP) serving as a test case. It is concluded that, the Monte Carlo Simulation technique gives a more realistic judgement of the economic viability of gold mining projects.

May 1, 2004

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Mark Colwell, Christopher Mark

This paper summarises the results of a research project whose goal was to provide the Australian coal industry with a rib support design methodology and software tool that could be utilised by suitably qualified colliery staff. The project was primarily funded by Australian Coal Association Research Program (ACARP) and further supported by several Australian longwall operations. The outcome of the project is a design methodology and software tool called, Analysis and Design of Rib Support (ADRS). ADRS is an empirical technique, which recognises that several geotechnical and design factors affect ribline performance and in addition that operational and safety issues essentially dictate the level of performance required. Therefore, the design recommendations associated with ADRS are specific to the Australian coal industry; however the procedure(s) for data collection and analysis could be applied to other countries' 'underground coal industries. Case history data were compiled from 34 longwall and two bord and pillar operations resulting in 204 case histories with each case history data set being defined by approximately 130 individual data fields. In addition monitoring (incorporating stress cells and extensometers) was undertaken at 10 collieries to assess and quantify the effectiveness of different rib support patterns and hardware on rib performance. The monitoring sites allowed for an improved understanding of the mechanisms of rib failure and degradation in terms of its interaction with the installed support and at the various stages of the mining cycle. The design methodology deals with both mains development and gateroad development specific to Australian longwall mines. This paper focuses on longwall gateroads subjected to abutment loading and in particular the travel road which becomes the tailgate of the subsequent panel. The statistical analyses associated with these cases suggested that the level of rib support should be based primarily on the development height and the pillar stress level. The ADRS software guides users through the design process, allowing them to develop rib support plans based on sound science and a broad base of in-mine experience To the best of the authors’ knowledge ADRS is the first systematic rib support design technique to be developed for any country’s underground coal industry. The development and use of empirical models in mining have substantially contributed to improving safety and productivity. ADRS further demonstrates that empirical techniques are particularly relevant and beneficial in dealing with the complexities of geotechnical design associated with underground coal mining.

Jan 6, 2008

By D. O’Connor, A. Pytlik, D. J. Corbett

The resistance of yielding rockbolts to multiple impact loads was tested by means of a drop hammer. The methodology was based on the ASTM D7401-08 standard as well as the requirements specified for rockbolts by Luossavaara-Kiirunavaara Aktiebolag (LKAB – a Swedish mining company) and the Safety In Mines Research Advisory Committee of South Africa (project number GAP 423). During the tests, the loading force and bolt elongation were measured with a sampling frequency of fs = 19.2 kHz. In order to analyse the phenomena involved, the tests were recorded using two independent high-speed video cameras (600 and 1000 frames per second) and one thermal camera (128 frames per second). The tests demonstrated that all the samples transferred double the gravitational potential energy of Ep = 50.85 kJ from the impact load of mass m = 2825 kg and impact velocity of v = 6.0 m/s without failure. Damage to the bolt-resin contact in the upper anchoring zone of the bolt in the steel tube occurred after subsequent impacts. As a result, the macro-deformed bolt exhibits additional yield, and its operation following the shearing of the resin bond is similar to that of a ‘cone bolt’. Only one test resulted in damage to the threaded bolt rod-nut coupling, during the fourth impact; however, no damage to the bolt-resin contact zone was observed.

Nov 6, 2023

By Q. Zhang

The necessary capability of the gravity transportation pipeline system for cemented coal gangue backfilling at the Suncun Coal Mine, China, is about 74.4 m3?h-1 according to mining production and working times in the mine. It is estimated that the working velocity and maximum pipe length-backfill depth ratio of the backfill system are 3.82m?s-1 and 5.4, respectively and that the probable backfill capability of the system is 110.18m3?h-1. Results of hydraulic calculations for the backfill transportation system show that the designed backfill system is reliable in flowability and sufficient for backfill capability needs.

May 1, 2007

By Yuexin Han, Zehong Wang, Fujia Yu, Wanzhong Yin, Xinchao Wei

Bauxite is the main raw material in alumina and refractory industries. China has plentiful bauxite resources, most of which belong to the diaspore type bauxite with characteristics of high aluminum content, high silicon content and low ratio of alumina and silica (A/S). The resources with A/S 4-7 account for more than 60% of the total resource reserves of bauxite. Therefore improving the A/S through bauxite desilication is the key task of bauxite concentration in China. Normally the grinding fineness of 80-90% - 0.074mm is required in the bauxite flotation process. Thus fine grinding of bauxite ores is necessary, which leads to the high energy consumption. In the meanwhile, bauxite ores are easy to produce slime during grinding processes. The large amount of slime produced in fine grinding greatly worsens the process environment of bauxite flotation, affects the separation performance and results in the loss of metal. Also, fine grinding makes the flotation concentrate difficult to dewater, while the water content in the flotation concentrate must be removed by distillation in the subsequent alumina dissolution process, causing the increase of energy consumption and cost in the production of alumina. In this study, the selective grinding behaviors were examined with Henan Bauxite as feed. Separation of alumina and silica at a coarser grinding fineness was achieved and new route was explored to enhance the desilication in bauxite concentration to improve the A/S of bauxite concentrate.

Jan 1, 2003

Study on Mechanism of Sphalerite Flotation in the Presence of Main Metal Ions by Molecular Mechanics

Sep 13, 2010

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Gernot Schenker

With the shut-down in the mid-1970s of the last shaft furnaces in the Harz Smelter Plant the long tradition of the Primary Lead Smelter in Oker came to an end. A continuation of the concern was nevertheless possible as a result of the timely commencement with the development and construction of lead production from secondary raw materials. Then as today, the most essential secondary raw material is lead accumulator scrap with over 80 % of the raw material pallet. Already in the 1960?s a method of reclamation lead battery scrap was developed and successfully carr.ied out by Preussag. In 1983 this process was fundamentally modified, also for environmental protection reasons within the framework of a rehabilitation programme of the existing plant. Today Metaleurop's HarzMetall GmbH in Oker is equipped with a modern secondary lead smelter which includes all environmental protection installations required by law. Besides processing battery scrap, the. smelter is in a position to process a ?multitude of other lead bearing residues in an economically useful way, whose waste disposal would otherwise be impossible due to the ever-increasing environmental protection laws or only be achieved at great expense.

Jan 1, 1990

By G. Balletto, C. Furcas

"The mineral raw materials industry is a key-component of the Gross Domestic Product of industrialised economies, closely related to both the building and the industrial sectors. Despite this, at local level mining and quarrying are associated with both irreversible environmental damage and several visual alterations affecting the natural landscape. In this sense, SIA (Social Impact Assessment) has become a strategic tool that can not only improve the prediction but also the assessment of the social impact by involving the local communities in a participatory process. Taking into account the SIA experience, together with the examination of some relevant international case studies, it is possible to draw up a list of good practices for mining project management, from exploration through to closure and beyond, with quarry restoration. Such good practices will complement the existing studies, focusing on environmental issues, with the social issues arisen considered in SIA application."

Jan 1, 2011

By Allen Chung, John Twomey, Christopher J. Greet

"It is widely accepted that the type of grinding media has an impact on the grinding chemistry and subsequent flotation behaviour of the sulphide minerals being separated. There are countless laboratory investigations demonstrating that inert grinding media produces more oxidising pulp potentials, reduced levels of grinding media corrosion products and superior concentrate grades and valuable metal recoveries. However, taking these results to industrial scale has proven difficult.Work conducted at the Ernest Henry Mine, in north western Queensland, Australia, at laboratory and pilot plant scale clearly indicated that using a high chrome grinding media resulted in significant improvements in both copper and gold recoveries. However, advancing this work to plant trial represented considerable financial and technical risk to the mine.This paper provides details of the protocol developed and used during the high chrome grinding media plant trial. It describes the test regime employed to measure changes in pulp chemistry, and the statistical methodology utilised to interpret the results. The work also highlighted the need for close cooperation between the metallurgists on site and the researchers conducting the trial.To date, the trial has produced excellent results: indicating that the copper recovery has improved by about 2 percent. The successful application of high chrome grinding media to the Ernest Henry ore has increased metal value by $18.7 million USD per annum based on current spot price for copper.INTRODUCTIONTheoryThe application of electrochemically inert grinding media to mineral systems has been extensively studied (Table 1). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:"

Jan 1, 2011

A new personal respirable dust monitor developed by Rupprecht & Patashnick Co., Inc. in a multi-year project funded by the National Institute for Occupational Safety and Health (NIOSH) generated promising results in underground coal mine testing performed by NIOSH and industry representatives during the summer of 2003. The mine data showed that the personal dust monitor (PDM) performed similarly to co-located manual reference samplers for full-shift samples at all four underground coal mines at which the evaluation took place. The technology that forms the heart of the PDM, called the tapered element oscillating microbalance (TEOM system), is unique in its ability to collect suspended particles on a filter while simultaneously determining the accumulated mass with National Institute of Standards and Technology traceability. Because the monitor measures the true particle mass collected on its filter, its results do not exhibit the same sensitivity to water spray as do optically based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment, and reports dust loading data on a continuous basis. Using the device, miners and mine operators have the ability to view both the cumulative and projected end-of-shift mass concentration values, as well as a short-term 15- or 30-minute running average. During underground mine trials in the summer of 2003, technical personnel used the readings from the PDM to identify and correct several abnormal dust generating scenarios. These events demonstrated the potential of the PDM to be used as an engineering tool to evaluate the effectiveness of various dust control strategies. In a separate evaluation performed by CONSOL Energy, Inc., the mine operator evaluated the benefit of a proposed new water spray-based dust control system. Engineers measured the dust concentration upstream and downstream of a production location under different dust control scenarios using two PDM units. By evaluating the change in the dust loading between the upstream and downstream monitoring sites, the company was able to determine in a few hours which hardware configuration would yield the greatest benefit to the workplace environment. BACKGROUND Measuring underground coal mine dust concentrations is an essential part of protecting miners' health. The U.S. Secretary of Labor and the Federal Advisory Committee on the Elimination of Pneumoconiosis among Coal Mine Workers has recommended that better monitoring of coal miner dust exposures be used as a method to improve miner health. In consultation with labor, industry, and government, NIOSH issued a contract to Rupprecht & Patashnick Co., Inc. (R&P), Albany, N.Y., to develop a one-piece PDM. The object was to miniaturize TEOM technology into a form suitable for a person-wearable monitor that would enable accurate end-of-shift dust exposure information to be available to miners. Furthermore, any person-wearable dust monitor should minimize the burden to the wearer by incorporating the monitor into the mine worker's cap lamp battery, with exposure data continually displayed during the shift to enable workers and management to react to changes in dust exposure. In the summer of 2003, NIOSH conducted extensive testing of the PDM to determine its laboratory and in mine performance. In addition, anecdotal information collected in the mines showed several occasions where miners were able to identify situations that produced high levels of respirable coal mine dust The PDM's response to unplanned changes resulted in action being taken to keep dust exposures as low as possible. In another case that demonstrated the PDM's versatility, a mine was seeking to find a better dust control solution on its longwall headgate stageloader. In this instance, the PDM was used as a diagnostic tool by the miners to quickly evaluate the control technology. [ ] HOW DOES THE PDM WORK? The PDM is configured to provide accurate respirable dust personal exposure information in a form that is as convenient to wear as a normal cap lamp (See Figure 1). Respirable dust exposure data displayed by the device has two main objectives: providing the miner and mine operator with timely values to avoid overexposure to dust, allowing them to make any necessary changes during the course of a work shift; and computing an accurate end-of-shift statistic for a miner's average respirable dust exposure. The mass sensor embedded in the PDM, holds the key to the accurate, time-resolved dust concentration measurements. The inertial, gravimetric-equivalent, mass measurement technique used in the device typically provides a limit of detection on par with that of the most sensitive laboratory-based microbalances.