Search Documents

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By Martti Hagfors

Underwater explosions have been used as a test method for the determination of energy content of explosives for several decades. This is the only test method by which shock, gas heave and total energy values can be measured separately. The experimental data can be measured from the pressure-time curves measured by the pressure-recording unit. The shock energy is integrated from the shock peak area and the gas heave energy is calculated from the time interval between the primary shock wave front and the shock wave caused by the first bubble implosion. tb. Bubble period, tb, is the time of first bubble oscillation, the time which passes after the shock peak front to the first bubble peak. The total energy value is the sum of these two partial energies.

Jan 1, 2009

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By C. W. Taylor, F. L. Martin

"THE DICTIONARY defines Metallurgy as the ""science or art of separating metals from their ores and refining them for use"". In these days, however, such a definition is not detailed enough.The modern science of metallurgy is based on two fundamental sciences, physics .and chemistry, and is sub-divided into two major fields: Process Metallurgy and Physical Metallurgy. These fields of metallurgy are now so comprehensive and involved that even the graduate metallurgist has to specialize in one or the other.In recent years, the relatively new science or technology of non• destructive testing has also entered the industrial scene, with tremendous impact and ramifications. So much so that, certainly, no .discussion on metallurgy can be complete without including some reference to it.Obviously, one paper cannot hope to cover in detail the relationship of the whole science of metallurgy to the mining industry. Consequently, only a very brief reference will be made to the field of Process Metallurgy, our major concern being with Physical Metallurgy and Non-Destructive Testing."

Jan 1, 1960

By B. J. Moore

This publication contains routine analyses and related source data for 547 natural gas samples from 22 States and three foreign countries. Of this total, 340 samples were collected during calendar year 1967. The remaining 207 analyses are of samples collected during previous years, but releases granting, permission to publish the results were not received until 1967. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. The Bureau of Mines has conducted this survey in the United States since 1917, and in 1965 it was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 516.4 Nine previous publications have been made to present results of 7,618 gas analyses made by the Bureau of Mines Helium Activity prior to 1967. The first three, Bulletins 486,5 576,6 and 6177 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other six

Jan 1, 1968

By F. Peer

In most coal preparation processes, water is a necessary medium, but the presence of water in coal after it has been cleaned has a negative impact on transportation costs, handling and specific energy values. The utilization of super absorbent polymers (SAP) in the nappy application is well known. The concept of utilizing these polymers was investigated for the purposes of dewatering coal and other fines, generated by preparation processes such as flotation. SAPs are granular highly cross-linked synthetic copolymers with excellent water-absorbing properties. The dewatering process is characterized by three main stages: (a) contact of super absorbent polymer with high-moisture fine coal; (b) separation of dewatered fine coal from super absorbent polymer; and (c) regeneration of used super absorbent polymer, by exploiting its response to changes in conditions such as pH or temperature. Preliminary tests showed the separation step to be very difficult. The novel idea of encasing a given amount of polymer in a water permeable cloth solved this problem (of separating the swollen polymer from the dewatered coal). Preliminary tests investigating the effectiveness of the sachets of polymer showed a drastic decrease in the moisture contents of slurries. Furthermore, it was shown that it was possible to regenerate the polymer (still within the sachets) through thermal drying. A full-scale experimental programme was then followed to accurately determine the feasibility of using sachets of SAP. The experimental variables were initial slurry moisture content and polymer dosage. It was observed that the sachets seemed to work fastest and most effectively at high moistures and also at higher dosages of SAP. Regeneration of the polymer was also investigated, using two methods: thermal regeneration and pH-induced regeneration. The experimental variables, for investigating the regeneration process, were method of regeneration and grade of water used. Thermal regeneration at 70°C seemed to work successfully. Although the cost of using thermal energy is still a problem, the safety aspect (fire hazards) has been addressed since the polymer does not ignite when heated, unlike fine coal particles that may do so. The alternative method of regeneration, which exploits the pH-sensitivity of the polymer, was less successful, and further work needs to be conducted.

Jan 1, 2003

By Charles J. Cohen, Donald F. Reed

"INTRODUCTION AND ACKNOWLEDGMENTSThis report supplements a previous report on work done in this same area 4/ but covers only the period from November 1945 to November 1946. The project was established in 1943 to investigate magnetite deposits in the northwestern Adirondacks by geophysical surveying and diamond-drilling for the purpose of increasing iron production in the eastern United States.In its program of investigation of mineral deposits, the primary objective of the Bureau of Mines is the more effective utilization of our mineral resources, that they may make the greatest possible contribution to our national security and economy. The policy of the Bureau is to publish the facts developed by each project as soon as possible after its conclusion. Maps showing the detailed magnetic surveys of the deposits and anomalies discussed in this report are on open file at the offices of the Bureau of Mines, College Park, Md., and at the University of the State of New York in the office of the Director of the State Science Service, Educational Building, Albany, N. Y.The Mining Branch, Lowell B. Moon, chief, conducts preliminary exami¬nations, performs the actual investigations, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical analyses included in this report were made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under, the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, in charge of the laboratory service unit."

Nov 1, 1947

By Thomas T. Read

IN reviewing the field of mineral industry education last year reference was made to recent assertions, mostly emanating from sources not in a position to know the facts, that mining engineers as a class are disappearing. Attention might also then have been called to a statement that appeared in Engineering News, August 11, 1892 (p. 130), ". . . the great absolute decline in number of mining graduates, which last amounts almost to a complete abandonment of mining engineering as a distinct branch of study." Evidently we outrank opera stars in the number of farewell appearances we are able to make; 43

Jan 1, 1936

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By R. E. Siemens, Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites . The process consists of four mmaajjoorr steps : ( 1 ) reduction roast , ( 2 ) ammoniacal leach , ( 3 ) solvent extraction , and ( 4 ) electrowinning . Several solid - liquid separation steps are required that affect the economics of the overall process . In this study , two techniques for solid - liquid separation , centrifugation and thickening , were investigated . This report presents the results of ( 1 ) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and ( 2 ) an economic study of the two techniques , based on the requirements of a commercial - size ( 5,000 - tpd ) laterite processing plant . Sizing and other equipment - related recommendations , based on data from the Bureau's studies , were obtained from commercial manufacturers . The costs of thickening and centrifugation , including all the unit operations affected , were determined by the Bureau's process evaluation group . The total operating costs for separation using the two techniques ( including depreciation on the capital cost of equipment ) were found to be quite close : $ 17.26 per ton of laterite for centrifugation and $ 18.15 per ton of laterite for thickening . For centrifugal separation , the greatest cost was found to be the initial capital cost for the separation equipment ; using thickeners , the greatest cost was for reagent recovery .

Jan 1, 1983

By Christopher W. Corti

A major aim of the GOLD 2003 conference, is to promote new gold related science and technology with a view to developing new useful industrial applications for gold. Current industrial uses have provided a steady annual industrial demand for gold of around 350-400 tonnes in recent years, the bulk of which is centred on electronics applications, with dental uses constituting the second largest application. However, there is good reason to believe that whilst gold will continue to play a major role in these sectors in the future, substantial growth of demand is not anticipated. Increased industrial demand for gold is only likely to come through the emergence of new applications, probably most significantly in five broad market sectors: ? Pollution and emission control technologies, including fuel cells. ? New uses for gold in advanced electronics, electrical systems and devices. ? Chemical processing of a range of bulk and speciality chemicals, using gold based catalysts ? Advanced coatings exploiting the novel properties of gold, particularly in nanoparticulate form. ? New biomedical uses for gold including medical treatments, drugs, implants, sensors and devices. There is cause for optimism that many new applications for gold could emerge in these sectors over the next decade and that this will lead to a substantial growth in demand for gold. It is clear that many of these new opportunities will be based on a chemical approach to synthesis of useful products rather than what has historically been a materials or mechanical approach. To turn this expectation into reality requires sustained support of R & D and a determination to exploit this new science and technology into viable commercial applications.

Oct 1, 2003

By David L. Veith

As the basis for the State of Minnesota's Regional Copper-Nickel Study environmental evaluation, hypothetical mine models were developed ranging in ore capacity from 5.35 to 20.00 x 106 mtpy. Open pit and underground mining operations were defined utilizing conventional methods of ore extraction. Processing of the copper-nickel sulfide material involved conventional bulk flotation of the valuable minerals, with maximum water recycle And tailing disposal. Flash smelting and electrolytic refining of the concentrate resulted in 0.10 x 106 mtpy copper plus nickel metal, plus associated cobalt and precious metals. Variations in model parameters allowed environmental trade-offs to be identified.

Jan 1, 1980

By K. L. C. Gonçalves, V. K. Alves

"CVRD’s Department of Development and Technology – GETEK has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. This methodology has been applied in several prospective CVRD mining projects. It encompasses a procedure for variability analysis based on bench scale tests, pilot scale grinding and flotation tests and modeling and simulation for scaling up the industrial flowsheet.The bench scale tests include the determination of the Work Index, simplified DWT tests, rougher flotation and locked-cycle tests with samples that are representative of the ore body variability. After completion of these studies, continuous, pilot-scale flotation tests are carried out at a Mini Pilot Plant with drill core samples representative of different stages of the mine life. Finally, studies are carried out with large volume samples using a conventional grinding and flotation pilot plant. This sample is also used for liberation characterization, grinding kinetics, flotation kinetics and industrial circuit scale up. This methodology has been successfully employed in the development of CVRD’s new mining projectINTRODUCTIONCVRD has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. The definition of the processing route and the sizing and scale up of the processing system are some of the products generated during the pre-feasibility of a greenfield project. This paper is focused on the scale up of grinding and flotation circuits, operations known to be of the most importance in a mineral processing plant.The methodology for the definition of the flotation and grinding circuits is divided in the following stages: bench scale ore variability studies, pilot plant operation and modeling followed by simulation. The product of this work is a calibrated simulator that can be utilized for plant operation as well as mine planning, looking to achieve optimal operational conditions.The current models used for scale up of the grinding circuits are aimed at the generating information about the size distribution of the circuit product. However, it is well known that the liberation state of these products may be of critical importance for the performance of the concentration processes downstream. Nevertheless, CVRD has been developing a methodology for liberation kinetics during grinding, aimed at optimizing grinding circuit throughput together with downstream flotation recovery."

Jan 1, 2006

The main objectives of the Mine Mechanisation and Automation program (MMAP) are to enhance health and safety in underground mining operations, facilitate mechanization and automation in narrow-vein and deep mines, provide sound science to regulatory agencies and improve mine profitability. The program, which has a unique underground and surface industrial scale facility, is involved in many multi-partner projects, like hydrogen fuelcell applications, electrification and hydraulification of underground mines, reduction of noise and vibration, miner location device, explosive-free blasting and hoisting. The paper presents an overview of the Mine Mechanisation and Automation Program of Natural Resources Canada and some of the main projects.

Jan 1, 2002

By Stanley Noss

One need be neither an historian nor technologist to recognize that activi¬ties related to the conversion of coal to other usable energy forms have been active for nearly fifty years. The degree of such activity and its evolution to significant commercial proportions has, however, fluctuated widely with world circumstance. For the past decade there has existed both a consistent technology evolution effort in classic R & D proportions, and a mainstream commercial acti¬vity but in rather modest proportions when viewed from the vantage point of world energy needs. But the chain of events wherein it became increasingly obvious that we were in energy trouble irrespective of world politics, spurred alternative energy source activities in the fossil fuels areas. The oil embargo of 1973-1974 made the obvious even more so and provided additional emphasis for the need of such alternatives. Yet the preponderance of these added expenditures and activities (with one notable exception which is the subject of this discussion) has been focused on the intended identification of the best or ultimate process by means of analytical and modest empirical means, whereas our circumstance dictates a bold, higher-risk effort to prove the viability of coal conversion as an industry on a real-time, real-size, real-economics basis. With such proof on hand, industry demands in all related areas will provide the stimulus, motivation and environment for all processes. There is both need and room for many who will compete for a meaningful segment of this new industry which can grow at a rate never seen before in our growth history. The single program in the world today oriented specifically toward the goal of proof of industry viability is the Energy Research and Development Administration's CBF (clean boiler fuels) Program for which COALCON is proud to be the prime contractor.

Jan 1, 1976