Search Documents

By Juha Järvi

Outokumpu Zinc Oy has two separate roasting lines with fluidized bed furnaces and waste heat boilers for calcine collection and heat recovery. During the last 30 years, zinc production in Kokkola plant has increased continuously and at the same time the raw materials have changed. Therefore, the waste heat boiler has been under continuous research and development. The waste heat boiler plays a significant role in the process and consequently the reliability and efficiency of the device is important for the effectiveness of the entire process. Many changes have been made to the boiler in the last decades. New radiation tube screens, tube bundles, and baffle-plate constructions have been added to the boiler and also rapping systems for the dust have been developed. The latest improvement to the boilers was a baffle wall, located in the middle of the radiation section roof in the first boiler, and baffle plates in the lower part of the convection section in the second boiler. The new boiler design and optimization were carried out using physical water and air-dust modeling as well as computational fluid dynamics. The modeling work agrees well with experiences in practice. The latest developments have increased the operating hours per year and the effectiveness of the waste heat boiler.

Jan 1, 2002

By Heikki Tuovinen

The total utilization of raw materials and energy is the most important criterion when planning. industrial processes. The main goal is clearly to use the raw materials and energy as effectively as possible in order to make the desired products directly in the primary process itself', or to recycle unused materials and energy either as such, or after cleaning back into the process. However, few industrial processes are so straightforward. Most processes generate by-streams of materials and energy, which cannot be recycled directly and it is namely these by-streams which tend to remain as wastes. These by-streams are slags, dusts, vaporized metals, liquids, slurries, sludges, gases etc. Most base metal processes produce all these by-products. Waste water and gas emission controls and regulations are tightening all the time, so new processes must be developed to keep pace with these requirements. These processes generate more solid wastes, which must be utilized or at least processed into a harmless form landfilling. Municipal and hazardous wastes also contain valuable materials and energy, which must be used to minimize landfilling. The development of processes for these purposes places even greater demands on research and development. The same principles and methods developed for mining, ore dressing and metal refining processes can also be adapted for research and development work on processes for waste minimization. However, the problems encountered are much more complicated and less familiar, demanding more versatile and accurate tools and equipment. This paper presents principles, examples and some references of R & D work on processes for waste minimization.

Jan 1, 1992

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By Florian Kongoli

Converters have been playing an important role in the extraction and processing of metals ever since the first type of converter was invented about 100 years ago. Historically their operation has been mainly based on the experience of talented operators rather than on strict control and optimization technologies. However, in the new realities of unavoidable necessity to increase productivity and in the conditions of diversification of primary materials from various geographical areas, improving control and optimization techniques have become indispensable. In this paper a review of the authors? previous work in terms of improving control and optimization of converter operational practices related to magnetite content and precipitation, slag and metal blows, problematic and dangerous elements such as As, Sb etc. has been described by highlighting the advantages that the new control and optimization methods and tools bring to everyday converter practices. Several examples are given and future work is underlined

Jan 1, 2005

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By G. Barbery

The models for particle composition prediction that have been put forward are limited to simple textures and lead to an independance of grade with respect to particle size in broken ore. A presentation is made of a modification in texture description; binary textures, in which each subeonstituent has its own breakage characteristics are introduced. The calibration of the textural model can be made using heavy liquid separation results. The application to the case of coal is presented. Coal washability data present spe¬cial difficulty due to the distribution in the specific gravity of coal, which must be taken into account. Coal s.g. distribution is taken as a generalized exponential distribution. Model calibration is then possible and is shown to be in good agreement with experimental data.

Jan 1, 1987

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc. Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed.

Jan 1, 2003

By Joseph Gambogi

In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of futile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium. In this paper, we discuss all aspects of the titanium industry from ore deposits through extraction to present and future applications. The methods of both primary (mining of ore, extraction, and purification) and secondary (forming and machining) operations will be analyzed. The chemical and physical properties of titanium metal will be briefly examined. Present and future applications for titanium will be discussed. Finally, the economics of titanium metal production also are analyzed as well as the advantages and disadvantages of various alternative extraction methods.

Nov 26, 1999

By Ahmet Haxhiaj, Jaroslaw Drelich

"Both composition and porosity of pellets are the main parameters influencing the reductive melting process in water-jacket furnace during the roasting of sulfide lead concentrate. Roasting in a smelter located in Trepçë is done at about 9000C, for pellets which are composed of PbS, CaCO3, Fe2O3, and SiO2. In order to faciltiate the formation of slag in the reductive melting, the pellets must have the proper content of CaO, SiO2, and FeO, and porosity. The plant’s practice indicates that pellets with porosity of 18% do not melt adequately in the water-jacket furnace. The optimum porosity for the proper melting of pellets needs to be 32-40% and can be achieved when pellets are loaded with more than 10 wt.% CaO. Pellets with less than 10% CaO have a limited network of pores, such that reactive gases cannot reach the entire ore structure. Also, the composition of the pellets must satisfy the ratio of CaO : SiO2 : FeO = 1 : 1.2 : 1.8 to facilitate the formation of slag in the reductive melting process.IntroductionAgglomeration roasting of sulfide lead concentrate is an important phase in the production of lead by reductive melting [1-6]. The reductive melting process is a complex process with contradictory effects of several technological indexes which many times are hard to measure and determine. In this process, loading the water-jacket furnace with pellets of optimized composition and structure can reduce the consumption of coke, and achieve high level of lead recovery. Pellets (agglomerates) should be porous, but at the same time they should have necessary mechanical strength. ‘Self-melting’ ability of pellets is controlled by the types and quantities of fluxes blended into the pellet composition. Three major additives and their role are:"

Jan 1, 2011

By Rajesh Kumar Mishra

About 500,000 troy ounces of Platinum Group Metals (PGM) will be available for recycling each year from spent automobile catalytic converters in North America alone. Platinum Group Metals? from spent catalyst can be extracted by Hydrometallurgical, Pyrometallurgical or Gas Phase volatilization processes. This paper is a review and comparative study of various processes investigated for PGM extraction. A number of processes described in this paper have already been commercialized. The technical and environmental aspects of the important processes are discussed.

Jan 1, 1989

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By Kandipati Sreenivasarao

Ion and precipitate flotation involve adding an appropriate collector to aqueous solutions containing metal ions, to form hydrophobic metal-collector complexes or precipitates that can be removed by flotation. With a better fundamental understanding of the effects of physical, engineering and chemical parameters on the performance, ion and precipitate flotation techniques could usefully complement techniques now available for removing metal ions from dilute solutions. The removal of Cu(II), Pb(II), Cd(II), Cr(III) and Cr(V1) has been studied, using different types of collector, according to the nature of the metal-bearing species. The effects of collector/metal ion ratio, and solution and froth height on the flotation kinetics, bubble coverage by the metal-collector complex, recovery of metal and effluent quality are reported. The observed behavior is related to the solubility products of the metal-collector complexes, which were also determined.

Jan 1, 1994

By Richard D. Hagni

Although the economically important uranium minerals are difficult to recognize under the ore microscope, they can be identified by a combination of qualitative and quantitative techniques. Useful quantitative techniques include indentation hardness, percent reflectance, spectral reflectance curves, and color coordinates. The latter two properties are especially distinctive for the primary urahlferous minerals uraninite, coffinite, brannerlte, and davidite. Together with the quantitative properties of indentation hardness and reflectance, the character and color of internal reflections are distinctive for many of the secondary uranium minerals. Ore microscopic techniques also provide an excellent means for determining the intergrowths of these minerals with other ore and gangue minerals. Such intergrowths are important to an understanding of the genesis of uranium deposits, and they may be important to uranium extractions.

Jan 1, 1981

By Kunwar Pal, S. K. Tyagi, A. K. Pandey

"This study deals with the performance evaluation, technical and environmental aspects of different cookstove models (NIRE-02, NIRE-03 & NIRE-04). These cookstove models were designed, fabricated and evaluated following Bureau of Indian Standards (BIS) and their performance was compared from technical and environmental points of views. The theoretical efficiencies of all the cookstove models are found to be in good agreement with the experimental one. Also, the overall performance of these models is found to be in the order of (NIRE-04 > NIRE-03 > NIRE-02) which is also observed to be much better than that of the traditional cookstoves being used by the people in most of the developing countries around the world. The CO2 emission reduction from these models is found to be between 2.0-3.0 tons per household annually which is ultimately in good agreement with the experimental values.IntroductionMore than 2.5 billion people around the world depends on the biomass based resources for cooking and heating applications which includes wood, cattle dung, charcoal and agriculture residue [1,2]. Generally, people of rural area cook their food on unvented open fire, which burn biomass fuel inefficiently besides it creates many thermal and environment pollution hazardous causing health problems in the women and girl children due to more exposure of emissions. Also the consumption of biomass is very high as compared to the fossil fuels due to the fact that the large population of the developing countries lives in the rural area than that of in the urban area. It is estimated that about 3% of the diseases are caused due to incomplete combustion of biomass, which results in the around 1.8 million premature death every year including around 0.9 million death under five year of their age [3,4].Ramanathan and Carmichael [5] recently found that the black carbon of unburned smoke is playing a major role in global warming. The emission factors for different combinations of fuel and stove tested in China for direct and indirect GHGs as well as other airborne pollutants such as, CO2, CO, CH4, TNMHC, N2O, SOx, NOx, TSP etc. for a typical set of operating parameters [6]. The improved biomass cookstove technology came into assistance which is technically feasible, socially reliable and economically viable [7, 8]. The improved biomass cookstove not only reduces pressure on the biomass resource, but also reduces the environmental pollution and also minimize the time required for collection of fuel wood [9, 10]. Sharma et al. [11] emphasized on the adoption and large-scale propagation of efficient stoves to improve the health of rural women and to reduce the consumption of firewood and environmental pollution."

Jan 1, 2014

By Bin Xu, Qian Li, Yong-bin Yang, Xiao-liang Liu, Tao Jiang, Yan Zhang

Some high sulfur and arsenic-bearing gold concentrate has a gold leaching rate less than 80% by oxidation roasting-pickling-cyanidation process. The characteristics and intensification of gold leaching were studied systemically. By combining chemical composition and phase analysis, the low gold leaching rate was found to lie in the capsulation of gold by iron-containing phases including iron oxides, arsenopyrite and pyrite. 96.66% of gold in the industrial leaching residue was capsulated and 95.88% of the capsulated turned out to be in the iron-containing phases. The results of laboratory pickling-cyanidation experiments on the calcine and industrial leaching residue presented further demonstration for the fact that gold capsulated in the iron-containing phases was hard to be leached. However, the gold cyanide leaching rate of calcine could be raised over 95% by a reduction roasting-pickling pretreatment which played such a significant role in exposing the capsulated gold that gold leaching was intensified remarkably.

Jan 1, 2015

By Charles H. Bucknam

A gold sampling optimization study was carried out in support of open pit gold mining operations for the Newmont Gold Company Bootstrap-Capstone deposits in Northeastern Nevada. Six bulk samples were tested using fire refining techniques at field particle size, to determine coarse particle heterogeneity of the ores, and by gravity .concentration methods at 10 mesh particle size, to observe any particulate gold liberation. An overall sampling model is presented for the deposit based on the pooled test information, to reconcile the results of coarse particle heterogeneity testing and the fine particle 'liberation testing. The sampling model is used to recommend procedures to control the variability of gold grade estimation due to the fundamental error (nugget effect) during sampling, sample preparation and assaying of the ores and other fundamental variances. The technique of simplified quantitative risk analysis (SQRA) is used to provide an economic justification for implementation of. recommended improvements to field sampling practices.

Jan 1, 1999

By I. Barin

The thermodynamics of cyclone smelting of sulphidic copper ores is described using as example the production of copper matte with 75 wt % Cu. Equilibrium calcualtions and material and energy balances show that an increase in process temperature from 1600 K to 1900 K results in the extensive transfer of minor elements such as As, Sb, Bi, Pb, Zn,.... to the gas phase. A pilot plant for carrying out the cyclone smelting process is described. Calculations of material and heat transfer for the reaction of ZnS show that the smelting reactions of sulphides in the cyclone take place very rapidly at high temperatures. The dissociation of the sulphides with subsequent oxidation reactions in the gas phase plays an important part in. the process and is mainly controlled by heat transfer.

Jan 1, 1983

By Z. Zhang, R. G. Reddy

The viscosities of industrial lead slags with various compositions were measured as a function of temperature. It was found that viscosities of lead slags decreased with increasing temperature, and the plots of ln(11) vs. 104tr followed a linear relation over the reported ranges of temperature. Using the data of this study and available other related data from the literature, a viscosity expression was developed as a function of composition and temperature. The calculated results using this viscosity expression are in good agreement with the measured data. The composition dependency of viscosity of lead slags is discussed.

Jan 1, 2000

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By Xiao-hui Fan, Xu-ling Chen, Zhi-yuan Yu1, Guanghui Li, Min Gan, Yun-song Huang, Tao Jiang

Compared with the traditional de-NOx processes by cleaning the waste gas, a new approach for reducing the formation of NOx during sintering process is proposed. Since more than 90vol% of NOx comes from the fuel combustion, the influence of sintering coke breeze pretreated by CO(NH2)2 additive on the NOx emission is researched. As adding CO(NH2)2, the reduction agents (NHi) are generated during the pyrolysis of CO(NH2)2, which reinforce the NOx reduction, And the appropriate content of CO(NH2)2 is 1.0 mass% of coke breeze.

Jan 1, 2015