Search Documents

By H. L. Ludtke

Microlaminate composites were fabricated by electron-beam physical vapor deposition. The microlaminates consisted of five layers, each 2 to 4 pm thick, and were composed of either pure metal layers (Cu-Ag), or alternated between metal and intermetallic layers (Nb(Al)- Nb3Al). The microlaminates were heat treated in an Ar atmosphere for 2 to 12 hours, at temperatures of 600°C for the Cu-Ag and 1000°C to 1200°C for the Nb(Al)-NbsAl. Microlaminates were examined after deposition and after heat treatment by scanning electron microscopy and energy dispersive x-ray spectrometry. The effects of heat treatment on the morphological stability of these composites will be described.

Jan 1, 1999

By Suzzann Nordwick

The metallurgical treatment of mercury-containing materials for precious or base metals recovery imposes many processing and environmental challenges. Mercury is usually present as elemental or cinnabar. Historically, mercury has been removed from mined ores pyrometallurgically by roasting, but hydrometallurgical methods have also been employed. For example, alkaline sodium sulfide solution acts as an universal solvent for most mercury compounds. While, most other metals are highly insoluble in this solution. This allows for a high degree of selective separation of mercury from other metals with the exception of tin, antimony and arsenic. Mercury leached with a solution of sodium hydroxide and sodium sulfide or sulfur can be re-covered by cementation or stabilized through sulfide precipitation. Hydrometallurgical technology for the pretreatment of mercury removal from gold, silver, and base metal ores using alkaline sulfide leaching will be discussed with a focus on alkaline sulfide leaching of mercury sulfide-containing materials.

Jan 1, 2003

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Garlic peel was used as the raw material to synthesize the biosorbent for the selective recovery of precious metals from the acid chloride solution. Garlic peel is rich in carboxyl-, amino- and thiol-groups, has the potential of exhibiting high affinity to Au(III) when appropriate chemical modification process was employed. Here in the present study, the biosorbent was prepared by cross-linking garlic peel particles with concentrated sulfuric acid. Adsorption tests for mixing different metal ions such as Au(III), Fe(III), Cu(II), Ni(II) and Zn(II) from various concentrations of hydrochloric acid media indicated that Au(III) was selectively adsorbed on the cross-linked garlic peel gel over the other coexisting base metal ions investigated. The crosslinking mechanism and selective adsorption of Au(III) were also investigated briefly.IntroductionPrecious metals are quite popularly applied in the modern industries such as jewelry, electronics and electrical devices, catalysts in chemical industry, etc. While their high values, limited deposit and quite large demand in industry makes its recovery from the industrial wastes, typically e-wastes, quite necessary. Actually, many techniques have been developed to recycle and recover the precious metals from various industrial wastes effectively in last decades, but the cleaning and ecofriendly processes are still seriously scarce [1]. Taking into account of the typical recovery processes using cyanide lixiviant in the alkaline media, or aqua regia, followed by the further recovery process using activated carbon adsorption or cementation with zinc, iron or aluminum plate or powder, though they both are quite effective recovery processes, if considering the special requirements on safety and ecofriendliness for the modern hydrometallurgical processes, various improved or novel extraction processes are greatly demanded [2]. Recently, the biosorption technology applied to the recover precious metals in the hydrometallurgical process has become a concern [3,4]. Inoue’s research group made great progress in the recovery of precious metals such as gold, palladium and platinum from the e-wastes such as spent mobile phone by using biosorption from the hydrochloric acid media [5,6]. This new hydrometallurgical process exhibits the prominent advantages of being cost-effective for its short process, easy operation and near-zero emission. In the above recycling process for e-wastes treatment, the preparation of biosorbents is the key and backbone of the whole recovery process. For this purpose, they developed a series of suitable sorbents for precious metals recovery by using the tanning-based or cellulose-based biomass such as persimmon peel, grape peel, orange juicing residue, waste cotton, waste paper through the crosslinking process with concentrated sulfuric acid and relative chemical modification processes [7-10]. In the present study, we also applied this technique to prepare the biosorbent of precious metal uptaking by using garlic peels as the raw materials, and investigated the adsorption properties of such-obtained gel in the hydrochloric acid media."

Jan 1, 2012

By M. Bhattacharya, A. Dutta, P. Barat

"Pinning of dislocations at nanosized obstacles like precipitates, voids and bubbles, is a crucial mechanism in the context of phenomena like hardening and creep. The interaction between such an obstacle and a dislocation is often explored at fundamental level by means of analytical tools, atomistic simulations and finite element methods. Nevertheless, such studies fail to predict the effect on the overall plasticity on account of insufficient information about the underlying statistics of this process comprising a large number of dislocations and obstacles in a system. Here we propose a new statistical approach, where the statistics of pinning at idealized spherical obstacles is explored by taking into account the generalized size distribution of the obstacle along with the dislocation density within a three-dimensional framework. The application of this approach has been demonstrated for dislocation pinning at nanovoids in neutron irradiated type 316-stainless steel.IntroductionPresence of nanoscale obstacles like precipitates, voids and bubbles play a crucial role in determining the deformation behavior of a crystalline solid on account of the interactions between the line defects and such localized obstacles. In the context of the glide motion of dislocations, the obstacles can offer resistance to a moving dislocation, thereby causing a hardening effect [l-3]. In some other cases, inclusions like voids and bubbles can affect the rate of dislocation climb through diffusive [4] and non-diffusive [5] mechanisms. Over the last few decades, numerous studies have been performed to gain an insight of the dislocation-obstacle interactions at a fundamental level. These include the interactions responsible for the hardening effect, in addition to those pertaining to the non-conservative motion of dislocations.Although the elementary mechanisms of the various dislocation-obstacle interactions have been vastly explored and understood by means of analytical theory and numerical simulations, it remains difficult to quantitatively understand their effects on the macroscopic deformation behavior. This is due to the fact that their influence on the gross plastic deformation of a bulk sample would be the collective outcome of a large ensemble of such interactions. As a result, it becomes infeasible to predict the bulk deformation behavior of a material until the statistics of pinning of the dislocations at the localized obstacles is available. In the context of precipitate hardening, some well known attempts to extract the pinning-statistics were made by Friedel-Fleischer [6] and Mott [7] by analytical means, which were later tested through simplified 2-dimensional in-silica modeling [8]."

Jan 1, 2014

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Jae-Chun Lee, Jinki Jeong, Manis Kumar Jha, Divika Gupta, Pankaj Kumar Choubey

Rare metal indium (In) is mostly used as electroluminescent material in liquid crystal displays (LCD) monitors. Present paper describes leaching studies for the recovery of In from waste LCD monitors in presence of different other impurities. The leaching studies showed that more than 85% of In was leached out using 20% sulfuric acid at 60oC in mixing time 30 min at fixed pulp density 25 g/L. The solution could be purified using SX/IX and from the pure solution metal/ salt could be produced by evaporation, precipitation, electrolysis, crystallization processes.

Jan 1, 2014

By Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"Fine manganese fines are characterized by large amount and low price compared to lump manganese ores. However, fine manganese must be agglomerated as EAF (electric arc furnace) feed. In this paper, high quality fired pellets were produced by simulating grate-kiln process to supply the feed for EAF from some imported manganese ore fines containing high combined water. Manganese ore fines assaying 44.47wt%Mn, 5.89wt%Fe, 12.09%LOI and with 72.7wt% ranging between 0.5mm and 8mm, are pretreated up to the particle size of 84.7wt% passing 0.074mm by HPGR (high press grinding roller) twice in open circuit. The finely ground manganese fines were mixed with 1.2wt% bentonite, balled at 15% moisture for 7min in disc pelletizer. The drop numbers, compressive strength and thermal shock temperature of green balls reach 11 times/0.5m, 11 N/pellet and 360oC, respectively. After the green balls drying in the oven, the dry pellets were preheated at 1050oC for 12 min and then fired at 1300oC for 12 min in electric tube furnace. The compressive strength of fired pellets reaches 2621 N/pellet. Therefore, these pellets are high quality burden for blast furnace or EAF due to high mechanical strength and high Mn grade of 49.11wt% and low detrimental elements.IntroductionManganese, mainly using as deoxidizing agent, desulfurization agent and alloying elements, is widely used in the steel company. With the rapid development of iron and steel industry in China, domestic manganese ores cannot meet the requirement, resulting large quantities manganese ores import to China [1-4]. Compared to lump manganese ores, fine manganese ores containing high combined water are characterized by large amount and low price. However, they must be agglomerated as EAF (electric arc furnace) feed. There are three ways to agglomerate the manganese fine ores, sintering, briquetting and pelletizing [5-6]. Compared to the other two methods, pelletizing technology possesses the following superiorities, such as uniform size distribution of product, stabilizing chemical composition of product and lower energy consumption in producing. Therefore, pelletizing is a superior way to treat the fine manganese ores [7]. The systematic research of producing manganese oxide pellets by fine manganese ores containing high combined water was studied in this paper."

Jan 1, 2011

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By Lucas Barbosa de Souza Martins, Felipe Perissé Duarte Lopes, Nathalia Carneiro Garcia Rosa, Lucas Lopes da Costa, Sergio Neves Monteiro, Rubén Jesus Sanchez Rodriguez

"The fibers extracted from the stem of the banana plant are relatively stronger and have been used as reinforcement of polymer matrix composites. In addition to quasi-static mechanical properties, there is a need to characterize the dynamic behavior of banana fiber composites subjected to thermal and mechanical constraints. In this work, the temperature variation of the dynamicmechanical parameters of polyester composites incorporated with up 30% in volume of banana fibers were investigated by DMA tests. The storage and loss moduli as well as the tangent delta were measured from 20 to 200°C in a TA Instrument operated with the flexural mode at 1 Hz. The results showed that the incorporation of banana fibers tends to increase the viscoelastic stiffness of the polyester matrix. It was also observed changes in the T g and the structure dumping capacity of the composites with increasing fraction of banana fibers.IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times by our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber [1]. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites [2-7]. Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to C02 emissions responsible for global warming. Moreover, as compared to synthetics, lignocellulosic fibers present lower density and cost as well as reduced wear caused to the processing equipment. On the other hand, in terms of composite reinforcement, hydrophilic lignocellulosic fibers present drawbacks such as weak adhesion to hydrophobic polymeric matrices in addition to dimensional limitations and non-uniform properties."

Jan 1, 2011

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but industrially proven methodology utilizing nitrogen species catalyzation in the oxidizing pressure leach system may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a methodology for effective treatment of precious metals bearing chalcopyrite concentrates via partial oxidation at low temperatures and pressures will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 1999

By D. D. Harbuck

The U.S. Bureau of Mines recently identified a significant new source of scandium in an Oklahoma tantalum waste residue (approximately 0.24 pct Sc). Because scandium is a strategic and critical metal which the Department of Defense has classified for special consideration, the Bureau is researching methods of recovering scandium and associated metals from this and other process residues. A variety of operating parameters were evaluated to determine the best technique for recovering scandium. Testing showed that by sulfating the residue at temperatures as low as 150' C for reaction times as short as 0.5 hr, over 94 pct of the scandium converted to a water soluble form. Solvent extraction using DEHPA selectively recovered 100 pct of the scandium from the water leach solution.

Jan 1, 1992

By Tetsuya Uda, Sakae Shirayama

"With the aim of producing nickel (Ni) metal directly from acidic aqueous solution containing cobalt (Co) and other impurities, selective reduction of Ni was examined. As a preliminary experiment, sodium hypophosphite monohydrate (NaH2PO2·H2O) was selected as a reductant, and reacted with aqueous solution containing 0.1 mol L-1 nickel sulfate (NiSO4·6H2O) and 0 ~ 0.05 mol L-1 cobalt sulfate (CoSO4·7H2O) for 3 hours at 90 °C. As a result, it was revealed that Ni was selectively reduced and separated from Co in the acidic region (pH= 4.8). In this study, differences of reduction behavior between Ni and Co were investigated, and the feasibility of Ni I Co separation by the selective reduction of Ni was discussed.IntroductionEfficient Ni condensation and separation from Co are essential in nickel hydrometallurgical processes. Currently, the hydrometallurgical production of Ni from oxide ore is mainly carried out by acid leaching at elevated temperature, followed by the removal of impurities using neutralization, and condensation of Ni and Co into intermediate products such as hydroxides and sulfides. Then, the intermediate product is dissolved in acid aqueous solutions, and Ni I Co separation is conducted by solvent extraction. Finally, Ni and Co are recovered by electro-winning. This complicated process consumes large amounts of alkali, hydrogen sulfide (H2S), and organic solution in a multiple-staged process'. To reduce the consumption of these chemicals, it is important to recover Ni more efficiently from acidic aqueous solution containing impurities."

Jan 1, 2014

By J. -P. Nepper

It has been possible to largely contain converter aisle emissions of SO2 and fumes in the case of batch-wise operated Peirce Smith converters during normal blowing periods with the help of suitably designed primary hoods. Controlling the escape of off-gas during the periods of turning the converter in or out of the stack has been problematic in the past. Effective automated contro1 systems have been deve1oped for the purpose and successfully applied in smelter operations in Spain, Taiwan and Germany. This has led not only to an effective reduction of emissions in the converter environment but also to an improvement in the converter operation.

Jan 1, 1992

By A. Rohkohl, R. Piillenberg

The QSL plant at "BERZELIUS" Stolberg GmbH in Stolberg, Germany was commissioned in 1990, introducing a new era of lead smelting in the more than 150-year-old history of the lead smelter. The lead smelter in Stolberg has changed its appearance several times during its existence. Therefore, at many locations on the site, old and obsolete buildings and equipment parts can still be seen. They are often located side by side with new modern constructions like the QSL-plant and the mercury removal plant, and reflect the specific contrast between tradition and modern technology. After a brief description of the development of the smelter and its decision to implement the current novel plant, the most recent operating results are reported. Following some modifications to the process and equipment, which had become necessary along with the implementation of the new technology, the plant is in operation today at approximately 30% above its design capacity. These achieved production levels are not restricted by the QSL-reactor but by precedent and subsequent available equipment. The QSL-plant entirely complies with the demands of modern, energy-saving, ecologically compatible lead production technology. Stringent environmental standards are maintained on a continuing basis. The demonstrated viability and flexibility of the overall process permits the operation to adapt quickly to the prevailing economical situation worldwide.

Jan 1, 2000

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By Xuewei Lv

An intelligent recognition and quantification system for the micrographs iron ore sinter was developed in the current paper. The average distribution parameters in a gray histogram of minerals by a Gaussian gray distribution model were obtained. The feature curves of the gray histogram of two minerals were achieved by combining the two density functions. The feature indexes, such as the number and position of the peaks and the valleys of two minerals in different ratios, were quantified by differentiating the distribution functions. This algorithm is able to extract the feature of the minerals adequately and accurately for recognizing the composition and phases of the minerals intelligently.

Jan 1, 2009

By C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. M. Matos, C. Volzone

For industrial use, the smectite clays are usually treated with inorganic acid of high concentration at temperatures under boiling point, which provide the bentonite´s bleaching power. In the present paper, a sample of brown smectite from Paraiba, Brazil, was submitted to treatment under moderate conditions (90°C, reaction times of 1, 6, 12, 18 and 24hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5M, clay/acid solution ratio of 1g/10mL), aiming to reduce impurities, responsible for the color of the clay, without causing significant changes in their structure. The samples were characterized by scanning electron microscopy (SEM), energy dispersive X-ray detector (EDS), stereomicroscopy, Cation Exchange Capacity (CEC), Thermal Analysis (TG/DTA), and X-ray diffraction (XRD). It was observed a bleaching in samples with time of 12h to 18h. With the DRX was possible to monitor the peak intensity of the clay structure and the sample with 12 hours of treatment was not significantly altered its crystalline structure, maintaining the peak clay at d(001). The most pronounced changes in the bleaching occurred within the first 12 hours of acid treatment. Thus, clay can be used in products with high added value.

Jan 1, 2015