Search Documents

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Kim Fagerlund

A novel apparatus for studying refractory infiltration and dissolution/degradation under a temperature gradient was developed. To supersede conventional isothermal refractory testing, a new temperature gradient technique, based on a crucible equipped with a cooling element, has been developed to provide practical information on the penetration and dissolution of refractory materials under cooled conditions. This technique was adopted and applied to several refractory-slag systems. Commercially available magnesia chrome refractory bricks against a copper-containing calcium ferrite type of slag were tested and compared using both a conventional crucible test and the new temperature gradient method. The experiments were conducted at 1300-1420°C under a controlled atmosphere of nitrogen or air. It was noticed that the type of porosity has a significant effect on infiltration of magnesia chrome refractories. Furthemore, the copper-containing calcium ferrite slag caused a severe slag attack and refractory failure in some cases, due to its fluidity and corrosive nature.

Jan 1, 2002

By Ashok D. Dalvi

Production of nickel from laterite ores has occurred for over 100 years beginning with processing of garnieritic ores from New Caledonia. However, until now the world nickel supply has been predominantly from sulfide sources. Going forward, the authors project that the production of nickel from sulfide ores will remain more or less constant. Most of the expansion in nickel production capacity over the next ten years will come from processing of laterite ores. Thus the capital and operating costs of new laterite projects will have significant impact on the nickel supply and therefore price. The authors have reviewed the history and capital and operating costs of various recent laterite projects and capital and operating costs of these projects and those "on the drawing board". The authors have also evaluated the risk associated with such projects. The paper will discuss the impact of this and the recent history on the future development of laterite nickel projects.

Jan 1, 2004

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"The use of electromagnetic field to remove suspended particles from metals such as aluminum by pushing to the boundary has been well studied. However, the potential of this method is yet to be exploited for the removal of inclusions from silicon. Considering the increasing amount of Top-cut SoG-Si scraps year upon year, there is the need to harness all the potentials of technologies to recycle this materials to ensure sustainability. This study investigates, and discusses new results on the effect of processing parameters such as composition, coil current, and frequency on the removal of inclusions from silicon under high frequency AC electromagnetic field.IntroductionThe solar cell silicon making industry requires pure and clean silicon in order to maximize the conversion potential of the solar cell material. The conversion efficiency of solar cells is limited by minority carrier recombination at dislocations and those intra-granular defects such as impurities, small clusters of atoms, or precipitates [1]. Recent global developments in the energy sector with a drive for the production of clean, reliable, and affordable energy have stirred a rapid growth in the production of photovoltaic (PV) cells.[2] Thus over the years, silicon based PV cells has seen a lot of growth as it has a PV market share of over 90 % [3] either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [4]. MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from the air absorption during solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [5]. For sustainability the silicon in the top-cut silicon scraps must be recovered. Therefore methods for removing non-metallic particles, such as SiC and Si3N4, from the silicon are important in order to recycle the top-cut scraps to a useful feedstock for the silicon solar cells manufacturing."

Jan 1, 2012

By Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Katsukiyo Marukawa, Mashamichi Sano, Shigeta Hara

"Various subject of studies are discussed to develop ·innovative refining processes in the 21st century for cost reduction, production of high quality steel and environmental conservation. The future refining reactor should have abilities of highly efficient mixing and separation of different phases. It is stressed ·that applications of electromagnetic and ultrasound energies, and control of flow fields rate required to create the highly efficient mixing I separation reactor.IntroductionIn recent years, it seems that the research and development in the field of steelmaking has shifted its emphasis to the solidification I ingot-making process in which continuous casting plays the leading role. From a long-range point of view, however, the need for continual development of the refining process will probably increase but is very unlikely to decrease. In order to meet such demands, it is required that problems and issues of the present process should be clearly grasped and that there must be rapid progress in process elements, such as highly efficient mixing and separation of different phases.Applications of electromagnetic and ultrasound energies and flow field control will become important options for resolving the above-mentioned problems. By efficiently and skillfully incorporating these new technologies into high-efficiency mixing/separation reactors, the innovative refining process will be established in the early 21st century."

Jan 1, 2000

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By M. Giralico

Optimized mixer settler designs will now handle flows of over 25,000 GPM. The size and expense of the equipment hamper experimental settler optimization efforts. Computational Fluid Dynamics (CFD) is a timely and predictable tool for settler design development. In the past, CFD has been used to evaluate only the flow field in pumped and auxiliary tanks. A similar numerical analysis is used to evaluate settler flow and phase separation. Phase separation is analyzed using multiple species for the aqueous and organic phase. Experimental validation shows good agreement between the computational and experimental solutions in both flow field and phase separation. The computational model is used to show performance differences between various choices of settler geometry, liquid depth, with variable flow rates. Understanding the differences allows the development of optimized settler designs. System improvements are predicted to lower entrainment levels further and/or allow new smaller footprint designs. This paper focuses on the major design components of the settler and how future technological advances will lead to further improvements in their design. LIGHTNIN?s new designs will handle tomorrow?s production requirements, while maximizing profits.

Jan 1, 2003

By I. S. Escobar

Copper, particularly the oxygen-free grade Cu-OFP, is a candidate material for containers for the long-term isolation and disposal of high-level radioactive waste (HLW) in underground repositories. After having been buried for a few hundred years, all oxygen will have been consumed in the repository, and corrosion of the copper will be caused entirely by contact with dissolved sulfides. Chloride is another potential corrodant, but in deep repositories where groundwater is neutral or slightly alkaline, the effect of chlorides can be ignored on thermodynamic grounds. Thus, the corrosion of copper in the presence of sulfide ion and under reducing conditions has been studied using cyclic voltammetry and Tafel slope measurements. It is possible to determine the effect of sulphide ion on copper corrosion resistance which is minimized at low temperature and also at low sulphide concentration. The presence of anions such as HCO3 under environmental conditions produces a beneficial effect because these ions are inhibitors.

Jan 1, 1999

By Andreas Nolte

In 1999 HÜTTENWERKE KAYSER AG (HK) in Germany will produce more than 180,000 t/y of electrolytic refined copper. To achieve this production from materials with copper grades from two to seventy percent and diverse copper alloys, HK operates three blast furnaces, one holding furnace two Peirce Smith converters and two anode furnaces. Technical, metallurgical and economic factors for the ongoing process optimization are outlined. The fluctuating quality and quantity of raw materials renders complex this optimization. The principal variables are the quality and quantity of process consumables: coke, copper-iron, limestone, oxygen, as well as the blending of feedstock and a new organization of the operating crews. The search for new metallurgical process parameters is ongoing. HK started with an intensive research programm in November 1997. As a result it will be possible to cut processing costs by about ten per cent, to increase the blast furnace capacity by ten per cent and to lower the metallurgical losses of copper and tin in the slag by more than ten percent. The presentation concludes with information on future steps to continue the optimization process.

Jan 1, 1999

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

By M. Kawakami

In order to make titanium ingot directly from molten slag, the metal pool was tried to form and used as the cathode. The electro-slag remelting (ESR) unit was used for the purpose. The unit is composed of water-cooled copper mold and the DC power source of 2000 A and 100V. The graphite electrode was used for anode and the base plate was used for cathode. The commercial and re-melted slag of CaO-CaF2 was melted in the mold with the addition of TiO2. The following reactions are expected to occur. Ti4+ + 4e = Ti at cathode 2O2- + 2C = 2CO + 4e at anode During the process, large amount of molten slag splashed out from the mold, showing the CO evolution at anode. The metal deposit was obtained but in the form of block and piled up on the base plate. The metal pool was not obtained perfectly because of shortage of heat supply. The cathodic current efficiency was 60 % at maximum. The metal deposit contained much impurity. In order to reduce the impurity and increase the current efficiency, the effect of electrode distance was examined. The electro-slag re-melting of titanium was tried in order to examine the condition to make metal pool.

Jan 1, 2006

By Junhong Noh, Kug Sun Hong, Jung-Kun Lee, Bo Ding

"The photocatalytic splitting of water into H2 and O2 by oxide nanoparticles has received much attention. However, the full potential of photo-catalysts for efficient hydrogen generation out of water has not been fully realized yet due to unresolved limitations including the low electrical conductivity and ineffective carrier extraction. Here, we report composite oxide materials consisting of 1-dimensional (1-D) transparent conducting oxide (TCO) core and TiO2 shell. Highly conductive ITO nanowires were grown on a flexible SUS mesh as a core component. The photoelectrodes consisting of these 1-D nanocomposites have increased carrier mobility due to the TCO core, while the TiO2 shell provides the photocatalytic functionalities. In addition, the built-in-potential at the interface between TCO core and the TiO2 shell improves the collection of charge carriers from TiO2 to TCO. These factors altogether contribute to increasing the photocurrent of the device under light.I. IntroductionPhotocatalytic behavior of semicondcutors has been extensively explored since it was discovered in TiO2 in 197Os. When TiO2 is exposed to UV light, the light is absorbed and electron/hole pairs are generated in the conduction and valeence bands. Holes in valence band will oxide/mineralize pollutant target directly or indirectly (via mediator hydroxyl radical). If the adsorbed A is O 2, O 2 will react with electron from conduction band to generate hydroxyl radical as described in the second set ofreactions. The photocatalytic reaction is schematically explained in Figure 1.Photoelectrochemical (PEC) cells using the photocatalytic reaction have attracted emerging interest as a potential route to convert solar radiation into useful forms of energy by reaction such as water splitting to generate hydrogen1 or the reduction of carbon dioxide.2 Another application ofphotocatalysis is water splitting and CO2 reduction, both of which utilize the electrons that are optically excited to the conduction band. 3•4 For this purpose, the conduction level of the semiconductor should be higher than hydrogen production level (EHZ1HZO) while the valence band should be lower than water oxidation level (Eo21112O). Electrons and holes will be generated on the semiconductor site, and holes generate O 2 at semiconductor site, while electrons will migrate to counter electrode to execute reduction forming H2. In addition to that, materials should be chemically stable to resist photocorrosion and have long lifetime of electron/hole pairs. TiO2 is a suitable material from the viewpoint of band arrangement and chemical stability requirement"

Jan 1, 2012

By Vladyslav P. Yakubovsky, Boris I. Bondarenko, Valentin A. Noskov, Vladyslav M. Sokolov

"Each of Ukrainian producers of ferronickel, stainless steel and synthetic diamonds has the same basic problem with recycling their fine Ni-containing secondary materials. The conditions for generation of them along with the correspondent properties were investigated in details. The new approaches for their recycling have been proposed. They are based on application of some pyrometallurgical processes that are used in Ukraine. The proper equipment is also available. It has been shown that the dust from laterite calcining process of ferronickel production should be efficiently recycled by sintering. The stainless steel dust should be smelted after briquetting as a charge addition to the Ni-containing discarded batteries in the elaborated furnace. The sludge after synthetic diamonds production should be pelletized and processed by liquid cast iron with application of induction magnetodynamic forces in the specific furnace.IntroductionThe object of the investigation is recycling the Ni-containing secondary fines in a form of dust and sludge. There are several generators of the fines in Ukraine. Namely they are Pobuzhye Integrated Ferronickel Mill; Electrometallurgical Works “Dneprospetsstal” with stainless steel plant as well as Poltava Diamond Plant that produces synthetic hard materials. Their businesses are the largest in the Commonwealth of Independent States (CIS). However the status of handling with the fines is not perfect since the applied recycling technologies are low efficient. The landfilling option is often adopted for them. At the same in Ukraine there are some nontraditional pyrometallurgical recycling technologies and equipment that should be tried for application in smelting these secondary materials.Recycling the sludge of synthetic diamonds productionThe sludge of “Poltava diamond plant” from production of synthetic hard materials has a following chemical composition, %: iron oxide – 29.7; chromium oxide – 18.97; nickel – 4.27; manganese oxide – 15.2; sulphate – 3.85; natrium – 14.9. The content of moisture is 70-80%. The moisture quite quickly evaporates while keeping sludge out of doors. Sludge returns into the weak agglomerates. The sizing of the dried sludge particles presents the figures from 400 to 1000 µm. The moisture was extracted by sludge pressing. The content of the basic compounds of the moisture is, g/dm3: chromium oxide – 1.6; nickel – 0.001; manganese oxide – 0.002; lead – 0.005; sulphate – 13.6; natrium – 17.0."

Jan 1, 2008

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988