Search Documents

By T. Iriyama, Y. Fujita, R. Omatsuzawa, T. Nishio, N. Okochi

Sm-Fe-N hard magnetic materials are good candidates for high performance bonded magnets. Rapid-quenching method should be highly favorable for the fabrication of isotropic magnet powder with high coercivity. We report here the magnetic properties of Sm-Fe-N powders produced by a few kinds of rapid-quenching processes. Sm2Fe17 powders were prepared by gas-atomization (GA), rotating-disk atomization (RDA), or melt-spinning (MS) method. The Sm2Fe17 GA powder had dendritic solidification structure, while the RDA powder had micro crystalline structure with size of 3-5 µm. Coercivities (HcI) of their nitrides were 56 (for GA) and 217 ka/m (for RDA). The H cI of nitrided Sm2Fe17 MS powder with wheel velocity (V5) of 5-20 m/s, which had also microcrystalline structure, was 53 to 509 Wm. These coercivity values are not sufficient for bonded magnet applications. From the study of additive effects, it was found that C, C-Si, C-Ga, or C-Al addition decreased the crystal size of quenched Sm2Fe17 powder. Consequently, high coercivity was obtained; the HcI of nitrided Sm2Fe1C1Si1 MS powder with V5 of 10 m/s was 898 kA/m, and 708 kA/m for the nitrided Sm2Fe15C1Si1 RDA powder. The compression-molded bonded magnet made from Sm2Fe18Si0.1Nx MS powder showed a high (BH)max of 82.7 kJ/m3.

Jan 1, 2000

By Mala Nath, Atjit Mallick, Asheesh Kumar

"The present research work is aimed to focus on the development of chemically stable light weight microporous carbonaceous material, such as activated charcoal incorporated either with titanium n-butoxide, titanium diisopropoxide bis(2,4-pentanedionate), vanadium 2,4-pentane-dionate or zinc 2,4-pentanedionate having varying wt% of the metal (2-8%) using ethanol as solvent at 40--50 oC followed by calcinations at 100, 150 and 200 cC, except the samples with titanium diisopropoxide bis(2,4-pentanedionate) which are calcinated at 80 oC. Atomic absorption studies along with FESEM revealed that the maximum incorporation of metals (Zn, V and Ti) in activated charcoal was observed with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC , 4 wt% of vanadium 2,4-pentanedionate at 100 oC, 2 wt% of titanium n-butoxide at 100 oC and 2 wt% of titanium diisopropoxide bis(2,4-pentanedionate) at 80 oC, and equilibration time of 20-24 h was used in each case. Hydrogen sorption behavior in these carbonaceous materials has also been studied at 77.4 K and low pressure up to I bar. The highest hydrogen uptake obtained was 1.45 wt% (164.5 cm3 (STP)/g at P/Po = 1.0) for activated charcoal incorporated with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC.IntroductionTwo of the major challenges for humanity in the next twenty years are the shrinking availability of fossil fuels, the global warming and potential climate changes that result from their ever-increasing use. So it is necessary to fmd an energy source that is convenient, flexible and controllable. One possible solution to these problems is to use an energy carrier such as hydrogen, and ways to produce and store hydrogen in electric power plants and vehicles. Hydrogen storage is the bottleneck for the breakthrough of hydrogen as energy carrier in automotive applications [1]."

Jan 1, 2012

By Guo Xueyi

The electrochemical couple behavior of manganese dioxide with ferrous/ferric ions in acidic chloride medium was investigated, It was proven that the dissolution of Mn01 is due to the electrochemical couple reaction between MnO2/Mn2+ and Fe2+/lFe3+ in the solution, The driving force for the process originates from the rest potential difference of the two couples. The reduction of Mn02 is controlled by clectrochemical kinetics, whereas the conversion of F e2+ to Fe3+ is limited by diffusion, The factors such as the Mn2+, Fe2+, Fe3+, Cl concentration, pH of the solution and the temperature, have much influence on the kinetics of the couple process, This study will be useful to elucidate the mechanism for the leaching of manganese nodule from the deep ocean as well as manganese dioxide ores in land,

Jan 1, 2003

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Courtney A. Young

All cyanide species are considered toxic and can be found predominantly in industrial effluents generated by metallurgical operations. For example, cyanide&apos;s strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent water contamination. Various methods of cyanide remediation by separation and destruction are available, but certain methods are more effective than others depending on the cyanide species being remediated. Photolytic destruction is regarded as the one technique that is independent of the cyanide species involved. The destruction of various cyanide species by several photolytic techniques has been investigated for the past few years. A literature survey suggests heterogeneous photocatalysis with anatase (TiO,) should behave similarly to homogeneous photolysis with hydrogen peroxide (H,O,) since proposed reaction mechanisms for both processes involve hydroxyl radicals. However, experimental evidence on a suite of cyanide species suggests otherwise. A new mechanism for the photocatalytic destruction of cyanides, especially SAD species, is therefore proposed.

Jan 1, 1998

By P. M. Tait, N. A. Warner

"The refining of thermally produced zinc is currently performed using a highly energy intensive and arguably outmoded process, distilling zinc under atmospheric pressure at temperatures of 900°C to 1000°C. In order to produce refined zinc more profitably and with less environmental impact a new process has been proposed. This process is generic to all thermal zinc smelters and aims to match the purity of zinc from current technology (99.99%-99.999%). The objective is to perform all separation processes using only the heat contained in the smelter product stream. Vacuum conditions are extensively used lowering operating temperatures and enhancing separations. As part of this process zinc is distilled under vacuum from high concentration obtaining a refined product with respect to lead content. A mathematical model has been developed from fundamental principles to describe this stage, the distillation of zinc across a temperature difference between two circulating zinc streams in open channels under vacuum. Heat for the distillation is supplied by the liquid phase, necessitating a large recycle to maintain high operating temperatures, and keep zinc concentrations high. In determining this model and the operating conditions required, relationships between temperature, pressure and composition are considered.IntroductionCurrent technology (the Refluxer) used to refine thermally produced zinc is both expensive and highly inefficient. At present 80% of the worlds zinc is produced via the electrolytic process reflecting the poorer performance of the thermal route, the zinc-lead blast furnace and Refluxer. A new process is proposed to overcome the drawbacks of current processes. These drawbacks are both economic and environmental. The Refluxer requires 6.6 GJ of energy to refine one tonne of SHG zinc 1, other disadvantages of the Refluxer stem from high operating temperature, around 900°C, and liquid zinc being highly corrosive towards ferrous metals. The Refluxer is constructed from silicon carbide sections which join together by means of flat machined faces making liquid metal leaks inevitable. The Refluxer columns are very sensitive to thermal cycling, thermal shock and mechanical vibration, which easily lead to structural failure. To avoid thermal stress on the columns the feed rate and feed temperature need to be kept constant which means the feed baths to the columns must be able to accept solid and liquid feed as the Refluxer has to operate when the smelter is shut down."

Jan 1, 1998

By Zhu Fangyi

"The article introduces the process EAF with De-P hot metal charging for Melting Stainless Steel in Baosteel stainless steel Branch. Based on the practice of production, the main effect on the Cr Loss during EAF with De-P Hot Metal Charging Melting Stainless Steel including using oxygen, the material charging and making slag are theoretically analyzed. The optimization of using oxygen can reduce the oxidation of Cr during EAF Melting Stainless Steel. The optimization of material charging, especially Si content is suitable can reduce the loss of Cr. Effective reduction can realize the lowest Cr oxide in slag. Based on the character of the process EAF with De-P hot metal charging for Melting Stainless Steel, applied the integrated control method, the Cr loss during EAF melting stainless steel decreased 43.10%. 1 INTRODUCTION EAF with De-P HM charging for melting stainless steel is a technology for stainless steel making. Practice prove that the new process can shorten tap to tap time, reduce the special power consumption, dilute the impurity element from the stainless steel scrap that is propitious to produce the high quality stainless steel, alleviate the shortage of stainless steel scrap to the production. As a new technology, the process has some technical problems and difficulties. The proportion of Cr alloy charging exceeds 20% during EAF with De-P hot metal charging melting stainless steel. As Cr alloy is difficult melting and easy oxidation, too much Cr alloy charging result in Cr loss too much and tap to tap time too long for EAF production. By applying the new technology, Baosteel stainless steel branch has increased the technology level and economy index. Now the content of Cr oxide in slag reduce from 8.59% to less than 6.0%. The Cr loss during EAF melting stainless steel decreased 43.10%. According to the practice application, the process of EAF with De-P HM melting stainless steel are theoretically analyzed. The main factors affecting the Cr loss during EAF with De-P hot metal charging melting stainless steel are discussed."

Jan 1, 2008

By Allan J. MacRae

A copper alloy to be used for coils in cast copper cooling blocks has been identified and samples prepared for metallurgical examination and destructive testing to compare with cast cooling blocks manufactured from copper and nickel-copper alloy pipes. The copper alloy allows for the formation of a metallurgical bond between the pipe and the cast copper during the casting process, which does not normally occur with pure copper or nickel-copper alloy pipes. The alloy&apos;s coefficient of thermal expansion is also much closer to that of pure copper compared with nickel-copper alloys, so there is less strain induced at the pipe-cast copper interface due to differential thermal expansion. It is expected that this new pipe coil alloy and associated casting techniques will allow for the production of cast copper cooling blocks that have greatly enhanced service life in high heat load applications compared to existing technologies.

Jan 1, 2002

By N. L. Piret, E. N. Mounsey

Ausmelt technology is successfully used to process primary and secondary materials to produce lead in large-scale commercial operations and to meet stringent environmental standards. The development and commercial data covering these applications and the results with respect to metallurgical, cost and environmental performance are reviewed in commercial operations. A new smelter is scheduled for commissioning in 2000 at Korea Zinc's Onsan site to process lead fume and other secondary materials to produce 50,000 tonnes per annum of lead bullion. The unique features of Ausmelt technology also allow for the efficient processing of polymetallic concentrates and secondary materials, particularly copper and lead, through the effective separation of these elements into metal, slag and fume species. This capability has been successfully demonstrated at a commercial scale and the results and implications for the industry are discussed.

Jan 1, 2000

By Kaspar Tall, Dmitri Goljandin, Kristiina Vilsaar, Jaan Kers, Valdek Mikli, Lifeng Zhang, Riho Tarbe, Viktor Laurmaa, Mart Saarna, Priidu Peetsalu

In this paper, the mechanical milling of the Printed Circuit Boards (PCB) was carried out. First goal of the work was to examine the management of the WEEE, in particular the re-use of PCB. Firstly, recycling methods of PCBs were summarized. During the study mechanical separation methods (magnetic-, density- and air separaten), electrical, and chemical methods were examined. Secondly the optimal particle size for air-classification was determined. Several tests were carried out to find the most effective separation method for separation of different material groups from PCB scrap. The new air classification stand was developed for testing the separation of lightweight particles like tinfoil stripes and plastics. The test results showed sufficiently good separation of heavier Al and Cu. For milled materials characterization the SA, IA, laser diffraction analysis and SEM were used. The chemical composition of the PCB powders was studied by means of energy dispersive X-ray microanalysis (EDS).

Jan 1, 2011

By B. Ozturk, K. Ito, R. J. Fruehan

"A simulation model for bath smelting processes for the production of iron was developed which predicts the coal, flux, ore, and oxygen consumptions and the off gas volume, temperature and composition. The model is comprehensive in that it takes into account all of the important variables including coal composition, metal composition, ore composition, slag basicity, post combustion ratio, (PCR), prereduction degree (PRO), heat transfer coefficient (HTC) , flux, scrap charge, and heat losses. Four basic cases were considered: I. 30% PRO-50% PCR; II. 90% PRO-O% PCR; III. 60% PRO-30% PCR; and IV. 0% PRO-50% PCR. Several different coals were considered and a sensitivity analysis of the critical variables was performed. The model also estimates the sulfur content of the metal. The major conclusions included:1. Post combustion significantly reduces coal consumption but above 20% PCR little reduction of FeO to Fe can be performed with the off gas.2. Prereducing to FeO (Case I) and having as much post combustion as consistent with good heat transfer is an attractive process. This process only requires a simple pre reducer, uses less coal, and is relatively insensitive to the type of coal used.3. High off gas temperatures may pose a potential problem. The off gas temperature can be reduced by using an 02-Air mixture for post combustion, limiting post combustion or adding water to the gas.4. The use of CaC03 in place of CaO or of supplemental electricity does not appear attractive.5. The melting unit is theoretically an energy efficient scrap melter. For Case I using 200 kg of scrap as part of the charge the coal consumption decreases by about 80 kg.6. With PCR > 30% the FeO content of the slag is expected to be 2-5%, and the metal will not be saturated with carbon. These factors and the increased sulfur load since coal is the fuel indicate the sulfur content of the metal may exceed 0.25%"

Jan 1, 1988

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By Michael P. Meisel

Solinox is a physical scrubbing process capable of removing a number of noxious materials from off-gasses, especially SO2, hydrocarbons, halo¬gens, heavy metals such as dust, etc. As these materials are dissolved physically, (not chemically bound), the solvent is absolutely stable and no by-products are formed in the scrubbing cycle. The process has been installed in three plants up to now, treating from approximately 30 MMSCFD to approximately 100 MMSCFD. These installations are in a non ferrous metal smelting operation, in a cellulose factory, and in a roasting process.

Jan 1, 1992

By Min Chen, Zhen Tian, Hongxu Cui

"The effects of adjusting technology on the phosphorous enrichment in converter slag were investigated. The results showed that the grain size of 2CaO·SiO2 with high phosphorus containing content increased slightly with the decreasing of cooling rate, and the proper cooling rate was confirmed to be about l.0°C.min-1. Moreover, the morphology of the phosphorus-rich phase of 2CaO·SiO2-3CaO·P2O 5 was changed from granular for the higher basicity of converter slag to the coexistence of granular shape and rod-like for the lower basicity of adjusted slag. With the addition of adjusting agent such as SiO2 to lower the basicity of converter slag, the phosphorus in converter slag could be transferred into 2CaO·Si02 phase effectively, and P2O 5 content in high phosphorus containing phase reached to above 30%.IntroductionThe yield of converter slag is very large in China, but most of the slag is stacked usually after the separation of iron, which not only takes up a lot of land, but also affects the ecological environment seriously. Therefore, improving the comprehensive utilization and value-added products of converter slag is of great significance to recycle the steelmaking slag[l-3]. On the other hand, the refining of hot metal with high phosphorous content is an unavoidable problem with the decreasing of high grade iron ore, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. However, the current recycle of converter slag is more focused on the emission reduction and reuse of steelmaking slag inside the iron and steelmaking process without considering the recycle of phosphorous resources[4-6]. At the same time, the development and utilization of phosphate ore as a strategic resource is drawing more and more attention, but the phosphate ore in China is mostly low grade and significant amounts of tailings are produced which is harmful to the environment. Therefore, it is important to separate phosphorous resources in steelmaking slag which can be used as phosphate ore for fertilizer material[7-9].Literature studies showed that most of the phosphorus in steelmaking slag existing as 2CaO·SiO2-3CaO·P2O 5 solid solution phase in 2CaO·SiO2 particle. The P2O 5 content in the phosphorus containing phase is very low due to the fact that the basicity of converter slag is usually high and the precipitated amounts of 2CaO·SiO2 particles during cooling are very large, resulting in the fact that the P2O 5 contents in 2CaO·SiO2-3CaO·P2O 5 solid solution phase are much lower which is impossible to be used as phosphorous resources instead of phosphate ore. Thus, the enrichment of phosphorus in steelmaking slag is need[ 10-14]."

Jan 1, 2011

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By Shulan Wang, Xuan Liu, Li Li

"Electrochemistry of Fe(III) in 69CaCl2-12CaF2-19KF and 81CaCl2-19KF (mole percentage, %) was investigated at 827 oC on molybdenum electrode by cyclic voltammetry, chronoamperometry and galvanostatic electrolysis using Fe2O3 as the Fe(III) source. The reduction of Fe(III) to Fe was conducted in one step and controlled by diffusion process. Fe(III) shown greater reduction rate and diffusion coefficient in molten 81CaCl2-19KF than in 69CaCl2- 12CaF2-19KF. Galvanostic electrolysis of Fe was performed in both molten salts with a cylindrical cathode rotating at 200 r/min and dendritic iron deposit was obtained.Keywords: iron; electrolysis; electrochemistry; molten saltIntroductionThe production of iron and steel causes huge emissions of CO2. Iron electrowinning in molten salts with dissolved Fe2O3 using an inert oxygen evolving anode is an alternative process to reduce or eliminate the formation of CO2. Research on novel process of producing metal has been reported recently [1-2] by using CaCl2 as the main electrolyte and dissolving CaO in CaCl2 due to the high solubility of CaO in the melt. This process has been used in preparing many active metals and alloys [3-14]. In the present work, the electrochemical behavior of iron in CaCl2-KF was studied and transport property of iron ion in the melt was discussed.ExperimentalCaCl2,CaF2 and KF (in analytical purity) were dried in air for 48 h. Mixed salts used in experiments were placed in a graphite crucible (??58 mm inner diameter). The graphite crucible together with the salts was heated at 473 K for 12 h in a furnace with flowing Ar (99.99%) before further heating. Temperature inside the furnace was measured by an S type thermocouple. Electrochemical measurements, such as cyclic voltammetry and chronocoulometry, were performed in a three electrode cell by EG&G PAR273A potentiostat/galvanostatand. Galvanostatic electrodepositon of iron was conducted in a two electrode cell. Molybdenum (??2 mm) and iron (??5 mm) were used as the working electrode (WE) and the reference electrode, respectively. A graphite crucible and a magnetite rod (??25 mm ) consisted of 100% magnetite and sintered at 950 oC in argon atmosphere for 2 h with electrical conductivity of 366 O-1m-1 at room temperature were used as the counter electrodes in the galvanostatic electrolysis experiment. Carbon (??10 mm) was used as the counter electrode in electrochemical measurement. The deposits were washed in distilled water bubbled with argon and dried in air before being characterized by X-ray diffraction (PW3040/60 diffractometer) and scanning electron microscope (SEM, SSX-550)."

Jan 1, 2014

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Martin J. Hansel, Jan Bäckström

Starting from historic perspectives on converting at the Rönnskär Smelter, the continuous developments of refractory practice is described. In the development the joint efforts of operators and suppliers of refractory have lead to significant achievements. This paper comprises the development of the converting process and the refractory lining as well as future prospects regarding operation and refractory lining design, especially in the face of equipment and raw material availability. 81

Jan 1, 2009

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008