Search Documents

By Shengqin Zhang, Jagannath Pal, Yousef Mohassab, Hong Yong Sohn, Mohamed Elzohiery

The kinetics of magnetite reduction with mixtures of hydrogen and CO of various compositions has been investigated as part of the development of a flash ironmaking process at the University of Utah. This new process bypasses the cokemaking and pelletization or sintering steps required for the blast furnace. The particle kinetics were studied using magnetite concentrate particles of different sizes. Reduction degree of 60% was achieved in a few seconds in at 1350 oC using CO reductant alone and over 90% when H2 + CO gas mixture was used. The effects of reductant partial pressures, temperature, and particle size on the reduction kinetics were studied.

Jan 1, 2016

By Cheng Fang, Zhou Lie-xing, Peng Jin-hui, Guo Sheng-hui

This article discusses the behavior of temperature and microwave thermo gravimetric analysis characteristic of ammonium paratungstate in a microwave field. Experimental results show that when 12g of material is place in a microwave with 900W of power, paratungstate’s temperature rises at 70°C/min. This results in paratungstate’s temperature being 980°C after 14 minutes. Compared with thermo gravimetric analysis characteristic, former two-step process of paratungstate microwave calcined completed ahead of schedule, after two-step process reaction is more intense,Paratungstate warming is more rapidly, the reaction time is much shorter; According to XRD and SEM, the product is high purity, the crystal particle size is uniform, and the grain size is fine.

Jan 1, 2015

By Georgios Kolliopoulos

Water is a critical commodity of our generation and a key compound for the chemical and mining industries. Sustainable industrial development is directly associated with the ability to recover clean water from contaminated sources. Forward Osmosis (FO) is a low-energy footprint membrane process allowing the recovery of clean water from high salinity effluent streams. In FO, water is recovered spontaneously into a concentrated draw solution (CDS). Energy is required to separate the recovered water from the resulting dilute draw solution (DDS). In the current work, the fundamentals of the FO process and the most important aspects affecting its performance are discussed. An energy comparison of FO and conventional water recovery technologies is presented. Finally, the opportunities FO presents in the field of hydrometallurgy are analyzed.

By Rafael Colás

Computer visualization can be employed in industry as an aid to the understanding of the complex interactions between variables encountered in production. The examples of ingot casting of rimming steel and that of hot rolling of low carbon steel strip are presented. Both processes are mathematically modeled, and their results are presented in a graphical way. Such models have been proven to be an asset in quality improvements and increase of productivity as the personnel involved get a better understanding of their job.

Jan 1, 1993

By Afshin Sadri

Acousto Ultrasonic-Echo (AU-E) is a technique developed to provide accurate measurements of the refractory lining wear in operating smelters based on the principles of stress wave propagation. The objective of the system is to provide feedback for the continuous optimization of the overall smelter operation. In some cases, the AU-E refractory lining measurements have allowed clients to extend their smelter campaigns and operate safely for several years beyond their planned reline schedule. In other cases, AU-E results inform clients of serious issues within their furnace allowing them to shut down their smelters ahead of predicted failures and possible disasters. This paper presents the results of several smelter AU-E inspections of the hearth and sidewall. These case studies demonstrate how the AU-E results were used to positively affect the smelter operation.

By Phillip B. Messersmith, Emmanuel P. Giannelis

"A versatile in-situ polymerization approach is described for the synthesis of polymerceramic nanocomposites consisting of two-dimensional layers of mica-type silicate (MTS) within polymer matrices. Functionalized, organically modified mica-type silicates (OMTS) were used to promote delamination/dispersion of the host layers and initiate polymerization of organic rrionomer. Epoxy nanocomposites prepared in this manner exhibit substantial modulus reinforcement at low silicate loadings. The water vapor permeability of the poly(?-caprolactone) nanocomposite containing 4.8% silicate by volume was reduced by nearly an order of magnitude compared to pure poly (?-caprolactone).IntroductionPolymer matrix nanocomposites are a relatively new class of materials with dimensions typically in the range of 1-100 nm.1 In general, because of the ultrafine phase dimensions involved, nanocomposites exhibit new and improved properties when compared to their micro- or macrocomposite counterparts. We as well as others are currently investigating the design, synthesis and characterization of polymer-ceramic nanocomposites. Our effort, in particular, has focused on the use of mica-type silicates (MTS) with various thermoplastic and thermosetting matrices.2-5MTS's belong to the general family of 2: 1 layered silicates. Their crystal structure consists of layers of two silica tetrahedral sheets fused to an edge-shared octahedral sheet of either aluminum or magnesium hydroxide. Stacking of the layers leads to a regular van der Waals gap or interlayer.6 Isomorphic substitution within the layers generates negative charges that are counterbalanced by cations residing in the interlayers. Although the natural forms of MTS's usually contain hydrated Na+ or K+ ions, ion exchange reactions with organic cations (e.g. alkylammonium ions) can render the normally hydrophilic MTS's organophilic."

Jan 1, 1994

By A. Kiziltas, D. J. Gardner, C. W. Mcllwraith, J. W. Bridge, M. L. Peterson

"Dynamic mechanical thermal analysis (DMTA) tests were conducted on high-oil content, paraffin-based wax used in wax-coated granular composites. These composites make up the surface of synthetic Thoroughbred horse racetracks used in North America. The modulus and damping response from the DMTA tests were correlated with the dynamic triaxial shear strength response of the bulk track material taken at two different operational temperatures and at four strain rates. The purpose of these tests is to understand the mechanisms of shear strengthening of the bulk track material as the wax is heated through the first crystalline solid to liquid nominal transition temperature. Previous work using differential scanning calorimetry confirmed that under common operational surface temperatures, the wax coatings undergo distinct thermal transitions. The resulting increase in triaxial shear strength values affects the consistency of the racetrack which, in turn, can potentially affect Thoroughbred racing performance and safety of the track surface.IntroductionSynthetic granular composite materials are being used in nine Thoroughbred horse racetracks in the United States as well as in other tracks around the world. In one case, their use was mandated by the state of California in 2007 due to testimony that these tracks were significantly safer than traditional dirt tracks [1]. Several synthetic tracks have shown substantial reductions in injuries since switching to synthetics; one California track showed a 75% reduction in catastrophic horse injuries during the first year as compared to the previous year racing on a dirt track [2]. The composition of the tracks in the U.S. generally consist of silica sand (>70%), polymer fibers (<5%), and rubber particles (0-15%) all coated with a paraffin-based, high oil content wax [3, 4]. In a recent study of several synthetic racetracks, to include the track location in this study, the oil content ranged from 34 to over 44% by mass [5]."

Jan 1, 2011

By Oleg I. Platonov

The process for desulfurizing coke oven gas in a regenerative system ?scrubber-stripper?, with sour gas being fed to Sulfur Recovery Unit (SRU) and tail gas being recycled to raw coke gas scrubber, has been developed. A key problem of this process is the presence of elemental sulfur in the SRU off-gas, which may deposit on gas-blowing equipment, thus disrupting its operation. A new treatment technology for SRU off-gas that has been worked out for a Claus unit operated by «Russian Metallurgical Company» (RMC) in Magnitogorsk (Russia) is presented. It incorporates a catalytic hydrolysis/hydrogenation stage, where all sulfur-bearing species such as sulfur dioxide, carbonyl sulfide and elemental sulfur are converted to hydrogen sulfide. The SRU in Magnitogorsk comprises three main units: gas re-heater; catalytic hydrolysis reactor and waste gas cooler. Re-heater is required to increase temperature of the process gas up to a level of catalytic conversion (beyond 330-3500C). Oxygen utilized as an oxidizing agent reduces the volume of waste gas to a minimal possible value. The operational data garnered since 16.07.2004 clearly shows that the new technology allows high-level purification of Claus tail gas from elemental sulfur. Unlike SCOT ? process, this technology does not require separate stages for H2S removal and enrichment that tangibly simplifies its implementation at lower capital and operation expenditures.

Jan 1, 2006

By Arthur E. Morris

Process modeling software is used extensively in process engineering, but there is a notable lack of affordable software for educational uses. This paper describes two educationally oriented software programs for thermochemical modeling of processes involving metals, minerals, and ceramic materials. Both programs run as Excel@ spreadsheet files. The first is FREED, a thermodynamic database program containing datafiles for 2500 species. It contains the entire U. S. Bureau of Mines and most of the U. S. Geological Survey database, plus data for scores of other species drawn from various sources. Several modules are available for manipulating and viewing the data. The second program is THERBAL, for making thermodynamic calculations using FREED data. Equilibrium calculations can be made for systems with non-ideal solutions, for a specified set of pressure, temperature, and input amounts of reactants. An optional heat balance is also calculated. The results are displayed as tables or charts in Excel worksheets. Examples of the use of THERBAL will be given for the reforming of natural gas for DRI production, DRI production, and EAF steelmaking. Some observations will be made on its use in the classroom. The development of FREED and THERBAL was initially carried out at the Department of Metallurgical Engineering, University of Missouri - Rolla as part of a project to preserve and enhance the Bureau of Mines database. The current versions were developed privately by the authors.

Jan 1, 2002

By D. Pradhan, R. G. Reddy

"Electrorefining of aluminum scrap was investigated from AlCl3 –1-Ethyl-3-methyl-imidazolium chloride (EMIC) (Molar ratio 1.65) chloroaluminate electrolyte using copper cathodes at temperature of 90±3°C and cell voltage of 1.5 V. The deposits were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The study was focused to determine the effect of electrode surface modification as well as deposition time on dendritic depositions of aluminum. Their effect on current density was investigated also. It was shown that the surface modification of electrodes reduced the dendritic depositions of aluminum. Pure aluminum (>99%) was deposited for all experiments with the current efficiency of 94-97%. The use of ionic liquids not only reduced the energy consumption but also minimized pollutant emissions (CO, CO2 etc.) compared to the commercial high temperature aluminum production.1. IntroductionAluminum electrorefining/recycling from aluminum scrap using ionic liquid electrolyte is an attractive process today because of the unique chemical and physical properties such as wide temperature range for the liquid phase, high thermal stability, negligible vapor pressure, low melting point and wide electrochemical window. But in conventional practice, melting of aluminum scrap and high temperature molten salt electrolysis makes this process more expensive and less energy intensive (average 13 kWh/ kilogram of aluminum) [1] . Although recycling scrap aluminum requires only 5% of the energy used to make new aluminum [1-2], but the green house emissions like CO2, CO and HF have to be counted for environmental reason. Approximately, 5.31 kilogram of CO2 emitted per kilogram of aluminum production in most of the US industries."

Jan 1, 2009

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By Lanre M. Oshinowo, André Bakker

"An understanding of the parameters that govern the just-suspended impeller speed, Njs, and the distribution of solids, is critical to the efficient operation of hydrometallurgical and other processes involving solid-liquid suspensions. In this paper, the distribution of solids in stirred tanks under a range of solids loadings (0.5 to 50 vol%) was predicted using CFD and validated against experimental data obtained from the literature. The multiphase flow is modeled using the Eulerian Granular Multiphase model. This paper will also review the established design parameter Njs in the context of scale-up and compare it to the quality of solids dispersion as a means of assessing correct scale-up in suspension tank design. The results of this study will describe a straightforward procedure to obtaining comprehensive information about reactor behavior with complex CFD models.The performance of hydrofoil impellers and a 45° pitched-blade turbine at suspending solids under different agitation speeds was studied. Both single and dual impeller operation have been evaluated. The settled solids fraction for speeds below N js, and the cloud height for impeller speeds above Njs were predicted. The CFD predictions are in good agreement with experimental literature data on velocity distribution and cloud height."

Jan 1, 2001

By San-chuan Tang, Wen Chen, Shun-ming Ning, Kan-ping Yu, Qiang Zhao, Xue-yong Xing

"A new type of desilication agent (PA-2) was selected by experiment based on the analysis of the characters of silica gel, and the influence of desilication type, desilication dosage, pH value, temperature and aging time on the desilicating effect was studied. The test results showed that on the conditions that pH was 2.0, temperature was 20""C, aging time was12 hours and the dosage of desilication agent was 0.23%, the desilication rate was higher than 93% in solution.IntroductionVanadium is an important strategic resources, which applies to steel industry and petrochemical industry. The main materials for vanadium product are steelmaking vanadium slag, stone coal and containing vanadium waste catalyst, etc. And stone coal is a low-grade carbonaceous silicified vanadium resource, which is unique material for vanadium extraction in China. Meanwhile, our stone coal reserves is No.l throughout the world.The silica acid solution containing vanadium is produced by acid leaching of raw stone coal or its roasted ore. The silica content of this solution is mostly high, besides, when pH is higher than 2 , the solution is unstable. Furthermore, it is very easy to generate gel substance with the increasing of pH value and standing time. 'Ibis silica gel is composed of colloidal particles with the size in 0.001 - 0.1 um. As a result, it is very hard even impossible for the following operation of solution."

Jan 1, 2013

By N. Mizutani, S. Harada, Z. Asaki, T. Tanabe

"The development of lead-free solders is urgent in view of environmental standpoints. In this -work the wettability of tin-bismuth- silver solders on copper was studied. Three kinds of fluxes were used. The wettability of conventional eutectic tin-lead .solder exhibited an excellent level over the other solders of tin-bismuth systems. Poor wettability of the tin-bismuth solders may be caused by the growth or dendritic copper-tin compounds at copper/solder interface, in contrast to the case of tin-lead'· solder. The wettability was improved by the addition· of silver in the solder. In this tin bismuth- silver system, silver was abnormally concentrated at the copper I solder interface even in the initial stage of contact. The wettability of the solder and the thickness of compound formed on the copper have a good correlation; the solder containing 2% silver exhibited the best wettability and the formation rate of copper-tin· compound on the copper was slowest.IntroductionSocial demand to avoid lead use in the industrial fields has been recently promoted· (1) because of the environmental protection of water resources. Especially the lead-bearing solders have been widely used in electronics and automobile products, and it is urgent to replace them with nontoxic materials (2)-(4). Thus the development of lead-free solders becomes an indispensable subject to the new generations and many works (5)(6) have already been carried out on the research and development of new solders. New lead-free solders are expected to have some requirements, for example, moderate melting temperature, proper strength and integrity, and lower prices, as compared with conventional solders. There have been already several alloy systems developed. Among ·these alloy systems, tin-bismuth binary or tin-bismuth-silver ternary alloys have great advantages such as having a wide range of soldering .temperature by controlling con:ipositions, though they have such disadvantages as ""lift-off"" (7)-(9): It is said, on the other hand, that a frequently overlooked property of solders, or one that is typically ignored by the research scientist as an ""issue"" for the manufacturing or product engineer, is wettability (10), although a ·work on the wettability has recently been published (11). In this Work, therefore, the authors selected Sn-Bi-Ag solders and focused mi the effect of Ag-addition to wettability of the solder."

Jan 1, 2000

By Akira Yazawa

The continuous converting has attractive advantages, but further experimental studies on the slag are required, when the process is considered thermodynamically. The summarized experimental results, obtained with iron silicate slag and with ferrite slag and results relating to actual operation are described and discussed in this paper. At first, equilibrium relations at controlled oxygen potentials among three melts of silica-saturated iron silicate slag, white metal and copper are investigated. The results obtained for slag agreed with the thermo-dynamical predictions. Namely, to suppress a magnetite separation, the system should be at high temperature; in the case of the S02 gas of 10 kPa, for example, magnetite did not separate from the slag at 1300°C, but at 1250 and 1200°C the slag was saturated with magnetite even at lower SO2 pressure. Copper losses caused by dissolution of its oxide increased with increasing 5O2 pressure, and were slightly lower than those reported in previous papers without the matte phase. When the continuous converting slag does not contain any appreciable amount of silica - in contrast to the conventional smelting slag ferrite slag would form, but there was no published fundamental work on-ferrite slags. Hence, the melting behavior and activities of the system CaO-Cu2O-Fe2O3 have been investigated. The liquidus diagram in nitrogen atmosphere was, constructed using both thermal analysis and quenching method. The low liquidus temperature region without magnetite separation was found in the part of low content of Cu2O in the section Cu2O-CaO-Fe2O3 and Cu2O?Fe2O3¬CaO?Fe2O3. The activity of Cu2O in the system was also measured. Slags, composed-of CaO, Cu2O and Fe2O3, in platinum crucibles were equilibrated at 1250°C and controlled oxygen pressures. After quenching, the-composition of slag and platinum crucible were determined qualitatively. On the thermo-dynamic analysis of the results, iso-activity lines were drawn, and it was shown that the slag in the converting furnace of the Mitsubishi process exists in an adequate region of the composition triangle.

Jan 1, 1976

By M. Brian Maple

A rich variety of phenomena are produced by superconducting-magnetic interactions in rare earth and actinide compounds. These phenomena, and the materials in. which they have been observed, are described in this talk, with an emphasis on the new high superconducting transition temperature (Tc) copper oxides. The Materials The-materials in which these phenomena occur can&apos; be divided into two classes. In the first group, there are two distinct interpenetrating systems of electrons, a set of localized 4f or 5f electrons and a set of itinerant electrons. The localized f electrons carry magnetic moments and interact with the spins and momenta of the the itinerant electrons, which are involved in the superconductivity, via exchange and electromagnetic interactions; respectively. This category includes materials containing rare earth (R) and actinide elements with partially-filled f electron shells which have been inroduced as substitutional impurities [e.g., La1-xCexA12, Th1-xUx] or form a sublattice in compounds [e.g., RRh4B4, RMo6S8, RMo6Se8, the high Tc. superconductors RBa2Cu3O7-d(d - 0.05)]. Materials of the second type are characterized by a single band of electrons that is responsible for both superconductivity and magnetic order. This group includes heavy electron rare earth and actinide compounds [e.g., CeCu2Si2, UBe13, UPt3, URu2Si2], and the high Tc copper oxide superconductors such as the hole-doped systems Lag- MxCuO4 (M = Ca, Sr, Ba, Na) and RBa2Cu3O7-d(0 =d= 1) and the electron-dope system Ln2-xMxCuO4-y (Ln = Pr, Nd, Sm, Eu; M = Ce, Th; x = 0.15; y - 0.02).

Jan 1, 1992

By Dai Yongnian

"The feasibility to vacuum distillation of a crude metal or an alloy was discussed. The equilibrium relationship between vapor phase and liquid phase in A-B system - - - - - PA/PB =BAa*/b has been derived. The separation coefficient, BA = rAPA/(rBPB) is a judgment criterion. By calculation PA/PB, the equilibrium composition diagram of vapor phase and liquid phase was drawn. By use of the equation derived by M. Olette, the relationship among the volatilization amounts of various impurities in a crude metal (yi) was further solved. 1-(X/100)= C =(1-Y1/100)1/02i . From yi value obtained in practice, 2i, Pi and then can be calcu-lated. The correct volatilization order of various impurities was obtained. These results can be applied to determine the practical conditions (temperture, vacuum degree, type of distilla¬tion furnace, times of distillation and control of product composition) in distillation of a crude metal or an alloy.INTRODUCTIONRefining and separation of various impurities from nonferrous crude metals by vacuum distillation have many the advantages of high metal recovery, impurities recovered in metallic state, flowsheet simplified, good enviromental protection, low operation costs and in complex equipment. So in recent years this method has been adopted widely.Vacuum distillation has also been studied and used in separation of various elements from non-ferrous alloys and the area of its application is being extended rapidly.At this situation, some problems have been put up: What kind of impurities can be removed from crude metals? What kind of alloys can be separated by vacuum distillation? In present paper, attemps have been made to answer these problems and combine with practical results to analyse some valuable data obtained from testwork on vacuum distillation of crude tin and Pb-Sn alloy."

Jan 1, 1988

By G. Richards

The Trail smelter of Teck Metals Ltd. produces about 90,000 tonnes of lead per year through two stages of refining following KIVCETTM smelting. Bullion from the KIVCET furnace is first treated in a pyro-refining plant in preparation for Betts electrorefining which makes 99.99% pure lead. Pyro-refining consists of number of integrated unit operations to remove primarily copper, arsenic, antimony and tin. The operation of this plant to meet the specifications for electrorefining requires attention to bullion management and selective use of reagents. The processes used for pyro-refining are reviewed in terms of chemistry and control.

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By Kimberly Conner-Mills

Due to increasingly stringent worldwide environmental regulations for gaseous, aqueous and solid waste emissions, conventional smelting technology cannot effectively process arsenic containing materials. Many globally significant copper properties have copper sulfide mineralogy that has a high arsenic content present as enargite with significant contained precious metals. As global copper, silver and gold demand increases while significant world resources decrease, treatment of sulfide orebodies with enargite is becoming increasingly important. Methods to selectively dissolve and fix arsenic, leaving behind clean copper and precious metals-bearing concentrates could effectively treat these ores.