Search Documents

By R. A. Haney

The Mine Safety and Health Administration has developed a model to estimate diesel particulate (dp) exposures in underground mines. The estimate uses either in-mine measured dp concentrations or engine manufacturers' standardized emission data and through a series of calculations estimates full shift dp concentrations by applying standard engineering principles of ventilation, control technology and work cycle. This model, in the form of a computer spreadsheet, provides the mining industry with a method to estimate diesel particulate levels and determine the impact of various diesel particulate controls on occupational exposure to dp in underground mines. A detailed description of the estimator and several examples demonstrating the results are provided.

Jan 1, 1998

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962

By W. A. Crosby

The ability of open pit mines to steepen overall final wall angles allows significant cost reductions as a result of reduced waste movement requirements. Final wall angles are principally controlled by three factors: geological conditions; hydrological conditions; and wall control blasting practices. The first of these factors is not controllable by the mine operator, the second can be influenced to some degree, but the last one certainly can be controlled, hence the current interest in final wall blasting practice at many mining companies. This paper discusses common blasting techniques employed to steepen final pit walls and outlines the attractiveness of moving from small hole high cost systems to the use of full size production drills as a means of reducing wall control blast costs. Attempts to make this change have been limited at many mines by the physical size of the drills and their inability to reverse drill. In the past, pres pi it, pre-shear or trim holes have had to be drilled vertically, at considerable distance from the upper bench toe, with the result that inter-berm face stability is reduced and final wall angles have to be made somewhat more shallow than desirable. The paper concludes with a description of how these problems can be overcome by utilizing the new Bucyrus 39R which has the capability of drilling at a ?15 degree angle underneath the machine. It is concluded that the resulting wall control blast designs will offer large mines improved final wall angles with resulting significant overall cost reductions.

Jan 1, 1998

By C. D. Keith

Erie Mining Company, a pioneer in the iron ore pelletizing industry, has continued to develop methods and equipment to improve cost and quality. Under the management of Pickands Mather & Co., this property, owned by Bethlehem Steel Corporation, Youngstown Sheet and Tube Company, Steel Company of Canada, Ltd., and Interlake, Inc., has initiated a number of operating improvements for the taconite industry. One of the most noteworthy of these, which is applicable to the entire mineral industry, is the principle of fine screening with rappers (FSR). Erie's original efforts in the field of fine screening, which date back to 1961, were described in the April 1967 issue of the MINING ENGINEERING magazine. In that same month, Erie placed into operation a full scale PSR and regrind plant addition, capable of processing 10.3 million long tons of iron ore concentrates, produced by conventional taconite grinding, classification, and magnetic separation methods. Since this first successful commercial operation of the PSR principle et Erie, it has been applied in eight other iron ore beneficiation plants end is being tested by other U.S. and foreign companies. In addition to the use of PSR units at Erie Mining Company, Pickands Mather has applied PSR to other of its managed properties end to projects under development. This paper covers these applications as well as a now application at Erie Mining Company.

Jan 1, 1971

By R. J. Good

It is well known that the elimination of impurities such as iron pyrite, shale, clay, silica, etc., from coal, by floatation [Sun, 1954; Aplan, 1983] and selective oil agglomeration [Keller and Burry; 1990] depends on the fact that coal is hydrophobic, and the impurities are hydrophilic. The water contact angle has long been used to evaluate the hydrophobic nature of coal, first by Brady and Gauger (1940), who demonstrated that the contact angle of water on coals increases with rank, and passes through a maximum at about 88% carbon. Brown (1962) found that the contact angle of coal decreased with increasing ash content. Sun, and also Aplan, have reported a direct relationship between values of the contact angle and rank, and have related the contact angle to coal floatability. Horsley and Smith (1951) first demonstrated that the captive bubble contact angle may be used to characterize the hydrophobicity of a coal containing more than 80% carbon DAF, while Parekh and Aplan (1978) have shown that the sessile-drop technique may be used to evaluate the hydrophobicity of coal of any rank.

Jan 1, 1992

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By E. C. Speers

The Ray Mines Division has a long and illustrious history beginning in 1911, as one of the early underground block caving copper mining operations. The tonnage mined from the beginning of operations, increased from about 8, 000 TPD in the early years to the present daily tonnage of 22, 500 tons, mined by open pit methods. The Ray basic milling practice has been relatively unchanged since 1927 when the sulphide-flotation process was introduced at Ray. The leach-precipitation-flotation process introduced in 1956 has been the only major process change. The change from underground to open pit' mining was accompanied by a renewed drilling and exploration program which developed large tonnages of low grade copper ores both in the porphyry and the diabase. The ore bodies as outlined were of such a grade and size that it soon became apparent that economical operations could not be developed with the lower tonnage rate. Also that in order to develop these newly proven ores, it would be necessary to move the Ray crushing plant, the Ray. supporting shops, offices, a substantial part of the Ray townsite, and would also involve the rerouting of Mineral Creek, a typical Arizona stream which is dry most of the year but can flow as high, as 8, 000 second feet in the rainy season. This paper describes those changes in flow sheet made necessary both by the increased tonnage .and the requirement to move as much of the crushing facilities from the Ray area as practical in order to free the mine for the extension of its physical limits.

Jan 1, 1961

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By George W. Land

For the year 1985, the U.S. coal industry produced 881 million tons of bituminous coal and lignite. Domestic consumption amounted to 814 million tons. The electric utilities consumed 689 million tons, almost 85 percent of total consumption, over 78 percent of production. In May, 1986, the NCA forecast that with moderate growth rate averaging 1.9% per year from 1985 through the year 2000, production could reach 1,176 billion tons and domestic consumption 1079 billion. The estimate for electric utilities indicate 924 million tons for the year of 2000, about the same percentage of production and consumption as now experienced. Before we consider the main topic of this paper, the cost of using high sulfur coal, let us examine the coal use patterns of the last 25 years, the changes in those patterns and consider the reasons for those changes. Table I shows those changes.

Jan 1, 1986

By R. Asmatulu

According to Darcy?s law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By Richard R. Klimpel

INTRODUCTION Previous papers by this author have discussed some of the difficulties involved with optimizing the performance of industrial flotation circuits, e.g. Klimpel (1988, 1989). The two major problems seem to be: 1) the inherent "systems" nature of the froth flotation process which leads to a great deal of self-compensation among the various operating options available and 2) the inherent variations in mineralogy, water chemistry, etc. that always seem to be present in industrial operations. In particular, the influence of reagent dosage has been emphasized in the above referenced work including an industrial system interaction denoted as the R/K trade-off, Klimpel (1984, 1987). Using a simple two parameter model for fitting time - recovery data, Klimpel (1980): [ ] where r is cumulative recovery at time t or at the t th cell, R is the long-term equilibrium recovery and K is the first-order rate of mass removal from the cell (time ), the definition of the R/K trade-off with increasing reagent dosage can be given as follows: at low dosages both R and K increase, at intermediate dosages R continues to increase but K starts to level out, and at high dosages, R may flatten out or still continue to increase but K starts to decrease, sometimes rather quickly. An illustration of this effect in a batch laboratory flotation cell is given in Figure 1. The purpose of this paper is to give a detailed plant illustration of this R/K trade-off phenomena with changing collector dosage which shows just how highly interactive the grindinglflotation system in sulfide mineral processing really is. This is one of about 20 plant level case studies that are being presented and evaluated in an upcoming book, Klimpel (1990). The particular study given here was completed in late 1979 on a copper ore of head grade 0.93% Cu. The frother being used was Dowfroth* 250 at a constant dosage of 0.15 g for each ton of solids feed to the rougher bank and the slurry pH was 10.2. The motivation of the study was to better understand the relationship of changes in feed rate (hence in particle size and state of liberation) with variations in collector dosage (potassium amyl xanthate). The major concern was to determine how much extra economic benefit could be gained by better utilizing the existing grinding mills and rougher bank consisting of eight identical cells. The remainder of the flotation circuit was also studied, including regrinding of rougher tails, but did not prove as critical as the rougher bank operation itself. It appeared from an overall economic viewpoint, the battle was being won or lost in the manner in which the rougher bank was being operated. This was not to minimize the roles of the scavenging and cleaning circuits but those portions of this particular circuit could be rather obviously operated to achieve maximum benefit given the specific output of the rougher bank. A special attempt was made to maintain constant ore type throughout the entire test program. Eight specific test conditions were evaluated including three different feed rates (and hence three different size distributions) to flotation. Tables 1 and 2 summarize the eight test conditions and overall recovery results at the end of the rougher bank for each test. A single test consisted of at least three consecutive eight-hour shifts operating at steady-state with composite cell lip samples taken over the final eight-hour shift. "Trademark of The Dow Chemical Company

Jan 1, 1990

By Margaret Fuller Boos

Precambrian granitic pegmatites on the west, south west, south and southeast slopes of Storm Mountain, Larimer County, northern Colorado, were explored and mapped geologically 1956-1959. The area between Crystal Mountain Mining District on the north and Hyatt pegmatite mine area on the south was nearly inaccessible until a company built an access road, which was completed in 1959, into Roosevelt National Forest and its jeep-type roads. The area is extremely rugged, rising from some 6,000 feet on the highway at Drake, on Big Thompson River, to an altitude of over 10,000 feet at the summit ridge of Storm Mountain. Almost innumerable pegmatites of every possible type of granitic pegmatite intrusion infest the Precambrian gneisses and schists of the southwest-tilted fault block of Storm Mountain. The major bodies stand at least 100 to 200, feet high above the surrounding forest floor. Core drilling has shown that some extend to at least 200 feet below the surface. They blunt out at the southwest, some keel out below and others are faulted out at their southwest ends. Strike length ranges from 200 to 600 feet. The massive bulky bodies have nearly vertical walls. Contents are zoned or ribboned and layered. They consist of local commercial bodies of beryl, potash feldspar, mica, uranium minerals and quartz. As yet no lithium minerals have been encountered.

Jan 1, 1960

By Duane B. Jorgensen

The two calcium sulfate minerals, gypsum and anhydrite, occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO, . 2H20) and anhydrite, the anhydrous form (CaSO,) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the larger part of total calcium sulfate resources. Although it has very minor economic use, it is important to the understanding of gypsum deposits and is referred to frequently in the following discussion. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have not yet been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. Most gypsum produced ranges from 80 to 95% pure and beneficiation is normally limited to selective mining or quarrying or upgrading by crushing and screening during mill processing. END USES The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris, the hemihydrate of calcium sulfate (CaSO4 ½ H2O), which when mixed with water will set or harden as the calcium sulfate returns to the stable dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uses of uncalcined gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in other countries with building practices different from those in the United States and Canada, relative usage varies widely. Calcium sulfate deposits are the world's largest sulfur resources; minor quantities of gypsum and anhydrite have been used to produce sulfur or sulfur compounds. This use is accompanied by a unique site-specific set of economics because sulfur is generally available from non-gypsum sources at lower cost.

Jan 1, 1994

By A. W. Dickerson

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research, Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Jan 1, 1997

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sandblasting agent, as a premium-grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. Staurolite is produced by E. I. duPont de Nemours and Company as a coproduct of titanium mineral production in Florida, where it was first recovered on a commercial scale in 1952 from the Pleistocene sand deposit known as Trail Ridge. At this deposit it comprises about one-fifth of the heavy mineral suite, the principal other heavy minerals being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and other nonconductive silicate heavy minerals are separated from the conductive titanium minerals on high-tension electrostatic separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total process, 200 t of raw sand yield 7 t of heavy mineral concentrate from which about 1 t of staurolite is recovered. The staurolite concentrates have the characteristics given in Table 1. Staurolite concentrates are sold in three grades having the size distribution of subrounded grains shown in Table 2. All three grades are used in sandblasting for cleaning metal, for paint removal, and for cleaning masonry buildings. Staurolite compares favorably with lower priced abrasives, such as boiler slags and silica sand, in applications where the abrasive is used only once and is not recovered and recycled. Because it is hard, fine, clean, and dense it can reduce blasting time, and less material is required to clean a specific area. Compared to higher priced abrasives such as aluminum oxide and garnet, which are recycled, staurolite costs significantly less per kilogram and cleans at equal or faster rates. Its breakdown factor, which is a measure of recycling performance, is intermediate between those for aluminum oxide and garnet. [ ] [Tables 3 and 4] show the blast cleaning performance of the three staurolite grades compared to other abrasives. [Table 5] compares the longevity of premium priced abrasives during recycling. [Table 6] shows a cost comparison between silica sand and staurolite. Fringe benefits claimed for staurolite's use as an abrasive are: 1. Good flow properties and freedom from the lumps or slivers found in silica sand or boiler slag abrasives. 2. Low dusting affords good visibility, permits faster working, and reduces cleanup problems. 3. Heated storage is not required during freezing conditions, because the mineral is nonhygroscopic.

Jan 1, 1994

By S. S. Churchill

Introduction Amidst the apparent chaos of the final push to complete a major construction project, a small group of specialists works with great intensity. Armed with yellow "in test" and green "turned over to operations" tags, these startup engineers follow detailed preoperational test procedures to confirm that a plant is ready to operate. They follow a test schedule designed to complete individual process system in the order they will be needed by operations. After extensive preliminary testing, the startup engineers begin the truly exciting part of their work - initial operations. The thrill of engaging the clutch for the first time on a 10,000 horsepower grinding mill makes all the long hours worthwhile. Preoperational testing and startup are of critical importance to the success of a project. No other aspect of a construction project allows such opportunities for success or failure, and no other aspect is so critically influenced by careful planning. At Bechtel, the tasks of preoperational testing and startup are among the responsibilities of the Mine and Plant Operations group. The Preoperational Testing Process Preoperational testing is the transition phase between constructon and startup on a new plant. It includes the preparation of detailed test schedules and procedures. The schedules are used to coordinate construction completion activities, so that systems are available for startup and operations in a rational sequence. The procedures form the basis for performing the testing and documenting its completion. Tests include instrument calibration, wire insulation tests, wire termination verification, mechanical alignments and inspections, and system cleaning and flushing. Where possible, the systems are then operated on water and their performance recorded. Normally, either the construction contractor or a team of specialists has the responsibility to perform preoperational testing. Witnesses to the testing may be owner operations and maintenance personnel, engineers from the design firm, or specialists assigned to the project who provide assistance and guidance to the contractor in addition to witnesing the work.

Jan 1, 1986

By J. T. Crawford

The purpose of this paper is two fold. It will: (1) examine leasing analysis as a project evaluation criterion, and (2) compare the cost of leasing with other methods of financing. The use of leasing has grown extensively in recent years as a method of obtaining equipment. The computer industry has been highly dependent upon leasing from its earliest days to dispurse its equipment to the customer, while airlines and railroads acquire large segments of their aircraft and rolling stock by leasing. Over the last few years the mining industry has leased haulage trucks, bulldozers and other equipment of similar nature.

Jan 1, 1974

By T. S. Govindan

The first step in energy conservation in any industrial plant involves implementing many of the day-to-day "house-keeping" items such as fixing leaks, turning out lights, etc. When this step has been accomplished, additional opportunities require a detailed analysis of the energy systems, evaluation of risks and costs, and assignment of priorities. Examples of conservation schemes drawn from the experience of Du pont's Energy Management Consulting Services will be discussed. The utility of heat balances for kilns and dryers in minerals processing will be outlined. The inputs needed from Management for the success of conservation efforts will be discussed.

Jan 1, 1978

By R. A. Wyman

What unusual features are there about finding, winning, and using the industrial minerals of Canada which may be of interest and yet not widely known. Have you, for example, ever wondered where the raw material for those distinctive greenish grey statuettes, so readily recognizable as Eskimo carvings, comes from? Although stone suitable for carving is obtained at several northern locations, in recent years the Federal government, the Quebec government, and one or two private companies have shipped supplies of various rock types from other sources to central distribution points in the Canadian north for the express purpose of providing Eskimo artists with raw materials for carving. Canada is well endowed with industrial minerals, the extent and variety of which may be observed by a perusal of Table 1. In this table, materials currently produced are shown in the left-hand column; materials which are bordering upon economic viability are listed in the middle column; and materials which have been found in Canada in possible exploitable quantity, but for which [ ]

Jan 1, 1970