Search Documents

By K. Vanbroekhoven

An industrial site near the centre of a historical town in Flanders is characterized by chromium(VI) contamination of the groundwater. Since the potential for natural attenuation was not sufficient to control the groundwater plume as observed from different analyses like pH, Eh, soil oxidation and reduction capacity, the feasibility of site remediation based on in-situ bioprecipitation of chromium was examined in lab microcosm studies. By creating reducing conditions by addition of a carbon source in the groundwater, chromium(VI) can be biologically reduced to chromium(III), which can form an insoluble precipitate of chromium(III) hydroxide. Microcosms contained contaminated groundwater and aquifer samples that were collected and manipulated under anaerobic conditions. Three different carbon sources were screened for their effectiveness: molasses from sugar beet production, molasses form starch production (protamylasses) based on potato juice and lactate. The different concentrations of sugar molasses were used to determine the optimal conditions. A range of parameters was monitored at regular time intervals for a period of six months such as chromium(VI) and chromium(III), DOC, methane, pH, Eh. A rapid conversion of chromium(VI) to chromium(III) was observed for all conditions tested. However, extensive removal of chromium from the groundwater by precipitation was only achieved for a limited number of conditions. In general, lactate was found to be the most effective carbon source, slightly better than the lowest concentration of sugar molasses that was tested, which itself was more effective than molasses based on potato. Higher concentrations of molasses, although causing a steeper decline in redox potential, resulted in less effective Cr removal. Typically, the fermentation of molasses results in acidification and this drop in pH may hinder the formation of insoluble chromium(III)hydroxides. It may also be possible that certain components of the molasses form soluble complexes with chromium(III). For lactate, no significant drop in pH was observed. Following the laboratory microcosm tests, the stability of the chromium precipitates was examined by performing a sequential extraction on the microcosm materials. These were performed under redox conditions which were similar to the ones observed in the field. Since the outcome of these tests was positive, a pilot scale test was implemented in the field in April 2005. Two different substrates, the cheap waste product sugar molasses and lactate are being injected creating two different impact zones and typical parameters are monitored. Frequent re-injections were important to maintain reduced conditions and are carried out three-weekly up to now. To study the stability of precipitates formed, mesocosm socks containing aquifer material were installed in the monitoring wells and harvested at regular intervals. Results of this pilot test will be presented and compared to the laboratory results. Based on the success of this field test, a full scale process will be designed and implemented as remediation strategy.

Jan 1, 2006

By Alan R. Grant

Interpretation of presently available geological information indicates that most of the periods of significant metal deposition in the Washington Cascades Range are, at least in part, genetically related to late Cretaceous -Tertiary intrusive episodes. Chemically, the most favorable environment for base metal deposition is high in potassium. Characterizing the advanced stages of these chemical alteration conditions are the silicate mineral assemblages orthoclase and/or secondary biotite. Wall rock alteration includes both deuteric and hydrothermal processes, the intensity of which primarily depends upon the degree of fracturing in the country rock prior to the introduction of secondary material. Broadly speaking, the primary physical controls for the distribution and concentration of sulfides appear to be a series of structural couples involving both northwest (paralleling regional trends) and northeast--striking systems. Meaningful base metal exploration in the Washington Cascades demands a basic understanding of the various geologic factors related to the distribution of the sulfide deposits. Any geologist contemplating Cascade work should be well grounded in the fundamental concepts of petrology and structure.as these constitute two of his most beneficial aids. The acquisition of the detailed data necessary for this understanding may seem a bit academic, yet it has been demonstrated in numerous instances that a fair economic appraisal of a particular property or mining district depends primarily upon the ability of the geologist to recognize the subtle environmental differences which could lead to the discovery of a major ore deposit.

Jan 1, 1971

By Ing. Ludwig Schlebusch

The significant growth of the world population and its demand for an increasing standard of living leaves no other choice than continuously augmenting industrial production and making available steadily greater quantities of raw materials at still better qualities. Therefore, any raw material has to be utilized to the greatest possible extent and processed at optimum economy on large mechanical equipment. The layout of processing facilities of large throughput rates can be based on multiple or single lines. The latter enables the application of large machines of optimum size. Proven equipment for homogenizing, classifying, separating superfine material, sorting and dewatering are-now available in optimum sizes. By the use of these large machines operating cost of pit coal preparation plant can be significantly lowered by reducing the specific requirements regarding space, capital investment, energy, operation and maintenance.

Jan 1, 1980

By Jerry L. Hodgson

This paper presents an application case history of the planning methods used for developing, costing and scheduling an underground hydro- electric pumped storage facility in weak rock. This method covers the system configuration, excavation methods and costs, initial support systems and final lining systems. This study was performed by the Omaha District, Corps of Engineers for the proposed Gregory County Hydro- electric Pumped Storage Project, and presents a synopsis and the results of the studies performed.

Jan 1, 1986

By Pieter C. van Aswegen, J. A. Brierley, C. L. Brierley

The bacterial-oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery is marketed by BlOMlN Technologies S.A. The process was originally developed by GENMIN who is still providing testwork, design and commissioning assistance to BIOMIN. Since 1986 three BIOX® plants have been commissioned by GENMIN. A further two plants will be commissioned during 1993 and 1994. The commissioning and operational experiences from these plants are described in the paper.

Jan 1, 1993

By J. C. Willett, J. R. Sanfilipo, S. M. Podwysocki, P. D. Warwick

The U.S. Geological Survey is concluding an assessment of the major coal regions of the country. In this program, the quantity and quality of coals that are expected to be mined during the next 30 years are characterized. For the Gulf Coast region, the evaluation includes reviews of the stratigraphic setting, coal resources, and the quality of the Cretaceous to Eocene coals in four coal-producing areas. The coal-bed methane potential for these areas will also be evaluated. The results of these efforts will be a series of digital maps, text, and tables that will be published in a CD-ROM format.

Jan 1, 2000

By Yoshiak Mizuta, Hi Keu Lee

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium

Jan 1, 1986

By J. F. T. Agapito, C. E. Brechtel, M. E. Adam

Full-scale stopping and simulated over- cast structures were constructed in large opening (30 ft high by 55 ft wide) room and pillar excavations in an oil shale mine. The program was undertaken to develop construction techniques and to generate data on structure costs and leakage rates. Leakage rates were measured using both sulfur hexafluoride tracer gas and "brattice window" methods at varying differential pressures. The measurements were conducted before and after a full-scale face blast to characterize the effects of blasting on leakage, and blast air pressures were measured across the stoppings. The operating performance of different combinations of permanent and temporary stoppings was evaluated by developing an operating model for a two-panel oil shale mine. The operating performance for the different stopping combinations was then compared to the system cost to evaluate the overall performance.

Jan 1, 1987

By A. Shtiza

This literature review discusses the role of the Albanian institutions, the natural resources industry, potential investors and stakeholders in order to provide a set of indicators that can help to monitor amelioration within sustainable development principles. A map with the potential prospects of the natural resources will be a first step in identifying the further potential for exploitation. Mineral resource policies and governance, sustainable processing and supply chain as well as environmental management information system are some of the crucial tools identified, that will help to set up the indicators and quantify the achievements in environmental management in Albania. Moreover, the integration of practices that will support institutional capacity building; follow-up practices; the mainstreaming of global environment into planning; and the compliance monitoring process will additionally improve the environmental situation in Albania. Aligning business strategy with environmental policy, socio-economic analysis, environmental auditing are decisive tools in order to provide the Albanian authorities with a clear overview of the economic costs and the social benefits for sustainable development.

Jan 1, 2011

By Lawrence Adler

[An innovative framework is proposed which most efficiently and systematically handles the large quantity of information needed for equipment failure and other non-performance analyses. It is based on the accepted engineering dimensions of mass (material), length (geometry), and time (MLT). To these are added human and machine factor. Several failure "Modes" are identified for each dimension, which are then subdivided into specific "Types". Material Failure Modes such as Separation and Slip are easily recognized, but others had to be established. Geometric Failure Modes are usually straight-forward, Obvious ones include Geometrics Design and Stability with more synthesized. Time Failure Modes are again largely self-evident such as Life and Chemical Effects, others are needed. Human and Machine Factors as failure modes are loosely assembled. The results contain strengths, but also organizational weaknesses which are noted. Lacking a better alternative its use is recommended.]

Jan 1, 1989

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high, through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1991

By H. Singh

Principal source of rhenium is molybdenite. Depending on the mineral processing route, rhenium can be recovered by one of the several alternative solvent extraction processes. Extensive experimental work has been carried out on the development of tertiary amine extraction process for treating very dilute highly impure scrub solutions obtained during scrubbing flue-gases of molybdenite oxidative roasting. Equilibrium data has been obtained under various process conditions by tracer analysis using radioactive Re-186. Extraction with 1% solution of a high molecular weight tertiary amine in kerosene, followed by scrubbing of organic extract with a solution of sulphuric acid and stripping with ammoniacal ammonium sulphate yields high recovery, concentration, and purification.

Jan 1, 1982

By J. D. Miller

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By J. A. Eisele, G. E. McClelland, M. D. Wroblewski

The Bureau of Mines is conducting research at its Reno Research Center to develop a staged agglomeration-heap leaching system and to electrowin the dissolved precious metals from the pregnant leaching solution. For direct electro- winning to be successful, the pregnant solutions generated during the Initial stages of leaching must be higher grade than obtained by conventional heap leaching. The precious metal concentration of the pregnant solution can be Increased by agglomeration pretreatment with cyanide solution which starts the leaching process during the curing period, by leaching with small volumes of solution and by cycling the leaching solution through more than one heap in a staged manner. The resulting pregnant solution is passed directly through an electrowinning circuit. The barren solution from electrowinning is recycled to the leaching circuit. Bench-scale research on the development of the staged leaching system and on the development of an efficient electrowinning cell are described. The Bureau of Mines developed agglomeration- heap leaching technology. This technology was readily adopted by the mining Industry for heap leaching crushed ores and mine wastes. Current research involves the application of this technology to finely ground feed materials such as precious metal-bearing milled tailings. Tailings agglomeration-heap leaching has also been used commercially.

Jan 1, 1984

By Douglas J. Uhren, Gary W. Gilbert

This paper describes the risk elements associated with difficult glacial geology, including boulders, heavy groundwater inflow, and potential running soils all coupled with a potentially corrosive service environment. The matrix workshop for the 168-inchfinished diameter sanitary sewer interceptor tunnel in Columbus, Ohio is assembled with the Design Team and the Owner’s design, operations, and fiscal staff. Corrosion protection alternatives are compared against cost and non-cost parameters with relative risk and weighting factors assigned. The Owner working in cooperation with the Design Team uses the matrix workshop to se

Jan 1, 2001

By John D. Kalasky

Island Creek Coal Company has had, for many years as a primary concern, the activity of handling large quantities of methane in the ventilation of its deep mines of southwest Virginia. Since the development of the Beatrice operation in the mid 19601s, the concern has been well founded, and through the years progress has been made in this most important facet of the extraction of the coal reserves to insure the safety of the employees engaged in the mining opera- t ions.

Jan 1, 1980

By Simon T. Johnson, Robert J. Fowell

The application of roadheading and drag tool equipped machines requires an assessment of both cutting performance and tool consumption. Neither parameter can be assessed purely from compressive strength and tool consumption is often neglected, at a cost to the project. Results from in-situ monitoring show that a measurement of relative abrasivity using the Cercharscratch abrasivity test provides a basis for the assessment of tool consumption. This can be modified by also considering the effects of the machine specification and the rock mass quality.

Jan 1, 1986

By Ronald K. Frobel, Christopher J. Wienecke

Geomembrane systems and associated geosynthetics such as geotextiles, geonets, geogrids and geocomposites have been used in precious metal heap leach and tailings facilities for many years. Geomembranes have been used in the heap leach process in pad design and solution recovery ponds as well as associated collection channels as the primary liquid barrier to contain and collect metal bearing leach solution. Geomembrane systems offer an effective, low cost alternative to other containment methods such as compacted low permeability soils, asphalt or concrete. In the 19BO's, rigid High Density Polyethylene (HOPE) liners were used to a great extent with a gradual transition to the use of the more flexible Very Low Density Polyethylene (VLDPE) and Polyvinyl Chloride (PVC). These three geomembrane systems have been used successfully in precious metal heap leach solution containment. Predominant material thicknesses have been 30 and 40 mil for PVC, 40 and 60 mil for HOPE and VLDPE. Variants in recent years have included roughened HDPE and VLDPE to provide higher surface friction characteristics, as well as newer polymer materials such as polypropylene. In addition to providing an economical method for providing enhanced solution recovery, geomernbranes are also providing the primary liquid barrier for prevention of groundwater contamination. Because heap leach solution chemical components and dissolved metal constituents are classified as toxic substances, they are subject to environmental regulation. Many regulatory agencies are still developing guidelines for heap leach pad design, however a geomernbrane liner system is often used as a single liner or in conjunction with other materials to form composite double or even triple lined systems. "Other" materials can include alternate layers of drainage aggregate, geotextiles, clay layers and other geomembrane or geocomposite layers.

Jan 1, 1993

By Y. T. John Kwong

Modified after procedures for assessing acid-generating potential of coal spoils, most acid-base-accounting (ABA) analyses inadequately characterize highly varied metal deposits. Although mineralogy critically controls acid generation and metal leaching, acquisition of appropriate data and their interpretation are poorly developed. Metal loading rates are commonly determined by kinetic testing, which rarely duplicate actual field samples and conditions. Accurate predictions and reduced assessment costs can conceivably be achieved by (i) use of geochemical analyses to define surrogate indicators; (ii) intelligent acquisition and use of mineralogical data; and, (iii) compilation of geo-environmental ore-deposit models to validate inference based on detailed geology.

Jan 1, 2000

By D. W. Dew, D. M. Miller, P. C. van Aswegen

The bacterial oxidation (BIOX®) process for pre-treatment of refractory ores for gold recovery is marketed by BIOMIN Technologies S.A. The process was originally developed by GENMIN who are still providing testwork, design and commissioning assistance to BIOMIN. This process offers an alternative to the more conventional roasting or pressure oxidation techniques with the following advantages: • Greatly reduced capital costs for small to medium size plants. • A relatively flexible and easily controllable process requiring relatively unskilled labour for operation. • Improved gold recovery. • A process that is environmentally friendly. The principal disadvantage of bacterial oxidation is the relatively slow kinetics compared to pressure oxidation and roasting, a plant residence time of 4 to 5 days typically being required to obtain complete liberation of gold from refractory sulphide minerals. Bacterial activity is also slow to recover from disruptions such as air supply failure or contamination by toxic species such as cyanide. Optimum plant performance depends on judicious management and sound training of operators.

Jan 1, 1993