Search Documents

By James N. L. Lukanuski

Three porphyry copper districts in southern Arizona are partly overlain by post-ore fanglomerates which share certain physical and petrologic characteris¬tics and which may comprise a distinct and significant class of rock. These units are the Locomotive fanglomerate of Ajo, the Helmet fanglomerate of Twin Buttes-Mission-Pima, and the Cloudburst formation of San Manuel-Kalamazoo, termed "Locomotive-type fanglomerates" herein. Post-ore units at Poston Butte and Lakeshore, Arizona, and Sar Chesmeh, Iran, also appear to fit this class. "Locomotive-type fanglomerates" are composed of poorly sorted conglomerates, lenticular sandstone beds, andesitic to rhyolitic flows and tuffs, and unique monothologic landslide breccias. They contain fragments of holyokeite - - a rare oligoclase lava of porcellaneous appearance. Their basal contacts are considered to be depositional and overlapping, sometimes complicated by later low-angle faulting. They arc quite different than the younger Cila, Pantano, and most "Whitetail" alluvial beds, and the older Amole, Recreation, Claflin Ranch, etc. elastics; in particular they are thinner and less widespread. Their ages are Eocene to late Oligocene. "Locomotive-type fanglomerates" may be genetically related to porphyry coppers as products of subsequent differentiation and volcanism, and sedimentation in short-lived basins of restricted area and extreme relief. They might be utilized as reconnaissance guides to target areas and as structural guides within target areas in the southwestern U.S., Northern Mexico, and elsewhere.

Jan 1, 1975

By Garland R. Dever

Extensive deposits of high-calcium limestone occur in the Upper Mississippian Warsaw and Ste. Genevieve Limestones in the region of the lower Cumberland, Tennessee, and Ohio Rivers in western Kentucky. Analyses of foot-by-foot samples from 20 quarries and cores in 8 counties show variations between the chemical composition of high-calcium deposits in the 2 formations. Knowledge of probable variations in composition should aid in prospecting for high-calcium stone for a specific use and in evaluating potential deposits. High-calcium strata in the Warsaw consist of bryozoan- and crinoid-rich bioclastic limestones, and in the Ste. Genevieve, predominantly oolitic limestones. Values used for comparison were obtained by averaging the foot-by-foot analyses of each high-calcium deposit, 10 in the Warsaw and 15 in the Ste. Genevieve. Average MgCO3 and Fe2O3 contents are generally lower in the Warsaw than in the Ste. Genevieve. Average SO2, S, and P contents are- generally higher in the Warsaw. No characteristic differences are apparent between the average CaCO3 and A1203 contents of the two formations. The higher S and P contents of the Warsaw are believed attributable to the predominance of biogenic material in these limestones. Within the Warsaw Limestone, higher average S and A1203 contents and lower average Fe2O3 contents were found in deposits in the northern half of the region. In the Ste. Genevieve, vertical variations in composition occur within individual high-calcium deposits containing oolitic and nonoolitic limestones. Lower average CaCO3 contents and higher average contents for the other constituents were found in the nonoolitic intervals.

Jan 1, 1972

By C. Rutter, S. Nelson

"Climax Molybdenum Company’s Henderson Mine, owned by Freeport McMoRan Inc., is a panel caving molybdenum mine located 69 km west of Denver, Colorado. The mine utilizes long interconnected ore passes as part of the ore flow system. Knowing the approximate level of ore in these ore passes is beneficial for preventing increased dust concentrations in various production areas, as well as scheduling truck loading operations. Level monitoring has been achieved by using a strain gauge placed on the steel structure of the truck chute, an amplifier and a Programmable Logic Controller. This paper explains the concepts and limitations associated with using strain gauges for ore pass monitoring as well as applying proactive dust prevention and level monitoring interfaces. INTRODUCTION The Henderson Mine, located 69 km west of Denver, Colorado, is an underground molybdenum mine which uses a panel caving process to produce 18,000 tonnes per day currently. This process involves dumping ore down a series of interconnected ore passes leading to truck chutes. Trucks use these chutes to load ore and deliver this ore to an underground crusher. If ore is pulled below the lowest intercept of these ore passes, a ventilation pressure imbalance occurs which generates a large amount of dust on the levels where ore is being loaded into the tops of the ore pass. When a dust event occurs, work must be stopped until the dust settles. Once the dust settles the ore passes must be filled significantly before trucks can start pulling from the corresponding chute. This downtime and unplanned work due to dust can be avoided if the approximate ore pass levels are known. Strain gauges have been installed and tested on a truck chute at the Henderson Mine and the results of these tests have led to a series of concepts in using strain gauges to monitor ore pass levels. This paper explores these concepts and corresponding limitations and explains how the application of ore pass monitoring can be achieved with the use of strain gauges. Ore Pass and Ventilation Pressure Imbalance Overview At the Henderson Mine, there are typically two or four ore passes in different drifts that combine into one bin to create an ore pass complex as shown in Figure 1. When the level of ore is at or below the 7210 intercept (I82W), four drifts have a ventilation connection to each other and the 7655 exhaust level. A “piston effect” is created each time a bucket of muck is dumped down the ore pass. Figure 2 illustrates this phenomenon: as the loader in 621 dumps a bucket down the ore pass, the muck pushes the air in the ore pass down the 82A leg and back up the 82B leg which generates a large amount of dust. The bin regulators on 7655 cannot be opened enough to allow for this surge of air to be relieved onto the exhaust level and the dust ends up exhausting into the 625 and 627 drifts."

Jan 1, 2018

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By Richard Klimpel

1. Introduction Laboratory and industrial grinding tests have shown that the process of size reduction can be significantly influenced by chemicals added to the powder or slurry being ground. The terms grinding aid or grinding additive refers to a substance which when mixed into the mill contents causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed feed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use. Obviously, an expensive chemical must be effective in very small concentrations if it is to be economically justifiable; the cost criteria is calculated on the basis of the cost of the grinding additive per ton of material ground. Although there is direct experimental verification of the advantageous effect of grinding additives, no sound scientific explanation has yet been offered which explains or predicts the general behavior of additives. Rose and Sullivan have summarized most of the work undertaken prior to 1950 and Hartley, Prisbrey, and Wick have recently prepared an updated synopsis of the grinding additive literature. Many of the studies reported consist of subjecting materials with simple geometric shapes to some type of hardness or controlled single fracture test. On the other hand, a number of the studies were carried out on operating industrial scale mills, with little control or precise monitoring of the effect of the additives.

Jan 1, 1977

By T. M. Yegulalp

One of the important factors affecting the determination of the minimum number of increments in a gross sample of coal is the variance component due to segregation. The segregation variance may be estimated by following the ASTM standard procedures. Since the estimate itself is a random variable, it is important to test if the value obtained is due to chance causes. This paper introduces a statistical test, based on the procedures published by ASTM, to test if the segregation variance is significantly greater than zero.

Jan 1, 1986

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989

By John Thella, Edward McNew, Christina Thella, Mends Emmanuel, Pengbo Chu

Ore sorting is an emerging technology in mineral processing that can produce a significant impact on the total mining and processing economics. The technology is capable of preconcentrating an ore based on differences in the mineralogical characteristics, which can include color, brightness, transparency, size, shape, density or near-infrared response. The current practice of conducting an ore sorting test typically requires large amounts of materials to be sent to a commercial testing facility, which is expensive and time-consuming. Here, we present a novel method to simulate commercial ore sorting on a laboratory scale using a rare earth ore.

Jan 1, 2025

By A. M. Stone

Following the conceptual idea of a Continuous Elution Process early in 1982, the system was successfully pilot plant tested at Western Mining's Kambalda gold plant in December 1982. As a consequence of these tests the Ok Tedi elution ciruit design was changed from batch operation to continuous operation resulting in a reduction in the number of similarly sized elution columns from five operating with one standby to one operating with one standby and halving the process steam requirements. In addition to providing significant capital and operating cost savings the continuous process was simpler to operate than the batch process.

Jan 1, 1989

By James W. Cooksley

Through the early stages of metamorphism, when diffusion is the predominant mineral forming process. there is a tendency toward homogenization of rock units; but there is also zoning resulting from differing primary lithology and structure. Later stages of metamorphism, when infiltration occurs, tend to intensify zoning within the rock mass. The above concepts have been borne out in exploration of talc deposits and skarns. Initially, geologic mapping and soil sampling are directed to understanding mineralogy and petrology. Later, seismic methods are employed to further define lithology in the subsurface. Magnetometer surveys can also define some metamorphic units efficiently. Then, drilling must ensue to confirm lithology and determine extent of mineralization.

Jan 1, 1992

By Charles N. Speltz

The cost of transportation of industrial minerals frequently is higher than the cost of the product. When a mine, industrial-mineral plant, or customer is served by a single railroad, because of the lack of competition, that railroad may in- crease rates and/or reduce service so that the economics of that mine, plant, or customer are affected adversely. Transloading of industrial minerals from rail-to-truck or truck-to-rail to improve economics and sales of product is not a new concept. However, transloading to create competition and reduce freight costs or to improve service is a relatively new concept brought on by the recent mergers of many of the main-line railroads, both in the eastern and western United States. For example, in 1998, with completion of the Burlington Northern/Santa Fe (BNSF) and the Union Pacific/Southern Pacific mergers (UPSP), the western United States has only two main-line railroads. The industrial-mineral producer, to reduce the cost of transportation or increase the level of service, must evaluate potential transloading opportunities in light of higher prices and reduced service brought on by reduced railroad competition. This paper discusses industrial-mineral transloading and examines the case history of the Tucker Hill perlite project in southern Oregon. The Tucker Hill project is a classic study of industrial-minerals transloading where the project would have failed without the transloading.

Jan 1, 1999

By D. Watson

The Henderson mine has more than 20 years experience and has placed a combined total of more than 400,000 m3 (520,000 cy) of shotcrete and concrete. Over the last 20 years the mine has used a variety of equipment for placing concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Henderson has recently received a state of the art wet shotcrete placer, automated its batch plant, fabricated a mobile concrete form jumbo and is soon to receive a new concrete transport truck.

Jan 1, 1992

By Haydn H. Murray

Kaolins and bentonites of economic importance in Australia and New Zealand are described. Clays that are used for structural clay products are not discussed. Residual, hydrothermal, and sedimentary kaolins are utilized including clays associated with coal measures. Bentonites are sedimentary and residual. Very little kaolin and no bentonite is exported presently, but this will change in the near future as transportation costs continue to escalate. Many areas of Australia, in particular, where kaolins are known to occur have not been investigated to determine the quality and quantity of the deposit.

Jan 1, 1982

By M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand for the material. This paper develops a general method of evaluating these needs and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can be projected to establish future requirements. This demand forecast is critical to the evaluation of a new source of supply, such as the graphite resources of upper Michigan.

Jan 1, 1989

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By Howard C. Homeyer

Coal and water are the two basic external feedstocks required for a coal gasification project. The WESCO project in northwest New Mexico, a joint undertaking of Texas Eastern Transmission Corporation and Pacific Lighting Corporation, will require about 25,000 tons of coal and approximately 7.5 million gallons of water each day to produce 250 million cubic feet per day (MMCFD) of pipeline quality substitute natural gas (SNG). The coal and water supply arrangement with Utah International, Inc. assures the project of an adequate supply of these two vital feedstocks.

Jan 1, 1974

By R. Conor, O&apos

Wastewater treatment systems, both industrial and municipal, produce large quantities of sludge which require disposal. Sludge disposal poses significant environmental liabilities, logistical problems, and economic burdens. Minergy Corporation has developed and implemented several new technologies for the recycling of such high volume wastes as sludge, ash, and foundry sand. These technologies perform mineral recovery from the waste material, converting them into construction material and industrial feed stocks which are inert, marketable products. With a continuously operating processing system installed at the waste source, these technologies reduce handling, eliminate downstream liabilities, and reduce disposal costs.

Jan 1, 1999