Search Documents

By Ian Graham

In 2013 the Government of New Zealand launched a number of ‘National Science Challenges’ (NSC) to address major issues facing the nation, and raise public consciousness about science and its role in promoting evidence-based decision making. One of the 10 proposed NSCs focuses on New Zealand’s extensive Exclusive Economic Zone (EEZ) and Extended Continental Shelf (ECS)1, with an objective to enhance utilisation of marine resources within environmental and biological constraints, and the desired outcome of:

Sep 1, 2014

By Andrew F. McKown, Lewis L. Oriard

Advances in explosives engineering are moving forward in several different aspects. These include improvements and new development in explosives products, the application of these products to blasting technologies, and the study of the peripheral effects of the use of explosives, such as ground vibrations and airblast. Topics of special interest in the last several years include new explosives and detonators, cap timing, explosive casting, high-speed photography, perimeter and slope control, air decking and mathematical modeling of blasting processes.

Jan 1, 1988

By Dennis C. Drehmel

Because of their relatively low cost, carbonate rocks are desirable in abatement of air pollution by acid gases. Although many processes and types of equipment have been proposed to control or prevent the emission of acid gases, this paper considers only three: dry-limestone injection, wet-limestone scrubbing, and chemically active fluid beds. For the dry-limestone-injection process, surface area-especially from pores in the 0. 2- to 0.3-micron range-is one of the important parameters which will discriminate between less and more reactive carbonate rocks. Marls, chalks, oolitic calcites, and other fine- grained limestones show larger-than-average surface areas and better- than-average removal efficiencies. Inert chemical impurities such as silica detract from reactivity. A dolomite is not necessarily less re- active than a calcite. For the wet-limestone-scrubbing process, dissolution rate of the carbonate rock controls the differences in stone reactivity. In this process the dolomites are less reactive than the calcites. In addition, more than 90 percent of the dolomitic impurity in Fredonia white lime- stone is inert during limestone scrubbing. Dissolution rate is also a function of particle size for large-grained carbonate rocks. Fine grinding of such rocks will increase the dissolution rate to that of a fine-grained rock. Hence the requirement of high dissolution rates may be met by some grinding of fine-grained material (e. g., marl, chalk, or other limestone) or by fine grinding of coarser grained material. For chemically active fluid beds, chalks have the best capacity to absorb both SO2 and H2S. However, most chalks are probably unsuitable for fluid beds because of high attrition rates. Because dolomites are generally more reactive than calcites with both SO2 and H2S, a dolomite would be the feed material of choice for a chemically active fluid bed.

Jan 1, 1974

By M. Javier

"Mining makes civilization possible. It also creates socio-economic problems surrounded by sustainability controversies yet continues extraction without considering the balance and finitude of nature. Nature requires restoration of equilibrium if mining and life on earth are to continue. Mining is still practiced according to Agricola’s views and the consequences it has wrought on our planet demand we critically reexamine it from its very core, to its metrics, to its design, to its technology, to how it is taught, and to reconsider its raison d'être in 2017. This paper offers tools to new mining engineers that are required to transform and solve new challenges. The task before us is to formulate an updated core curriculum that meets the demands and realities of the 21st Century. Mining professionals must rethink and reteach how to redesign mines before shovel hits dirt, how to mine with restoration of nature figured in to the mining design. Mining needs a new extractive technology in order to transform the results of its well-known liabilities. Mining has evolved and its future must be different than its past. Our industry is capable of doing this but it needs to be shown the way. INTRODUCTION The statement that ‘mining makes civilization possible’ is of the utmost importance and has the most value to us. We can examine the past and present appropriately to see the future that we are building. Mining must be addressed in a different way that makes a positive difference and improves upon rather than continues to get the negative impacts of the past. See Fig 1. Mining creates disequilibrium in Nature by producing ore, waste, tailing, dilution of resources, toxic, and pollution to its ecosystems. What is next for mining on a limited planet? Delaying the transformation of mining is not an option to developing an updated and modern mining business-as-usual paradigm. It is hurting the essentials of living in a civilization; our livelihood is in danger to the point of unrest in nature as we generate a lot of eco-print by present mining practices. So, we are urged to eliminate this bottleneck in life by employing a different design. This way, we will have a vision on how to sustain our civilization. [1]. This new design, with input from current and future generations, will be our contribution to posterity."

Jan 1, 2018

By J. F. McDonald

On December 8th of last year, the new St. Clair River tunnel was holed-through to Port Huron, Michigan. The tunnel, commissioned by the Canadian National Railway, was needed to replace an existing tunnel that had been built between 1889 and 1890, and had remained in continuous operation until the new tunnel was opened to traffic in April of this year. The original tunnel, after more than 100 years of service, was still structurally sound, but was too small to accommodate the double stacked container cars and other advances in the railroad's equipment that had developed over the years. Prior to the construction of the first tunnel, all freight was barged across the river. It was a slow, expensive process, which in winter was sometimes impossible. The nineteenth century tunnel was built in twenty months, utilizing two shields that mined to the middle from each end. The lining, which is still in excellent condition, consisted of bolted, cast iron segments, with an O.D. of 6.4 meters. It was the first sub-aqueous tunnel built in North American, and it's use of compressed air under the river and hydraulic power on the shields may also have been firsts. The digging was done by hand, and the muck hauled out by mule drawn wagons. Boulders and methane gas were reported to be a constant problem during the drive, and compressed air sickness was common, but when the two shields came together in August of 1890, it was reported that the alignment was within 6 mm. The new St. Clair River Tunnel was constructed for basically the same reason as the original. The larger equipment which the railroad is using today would not fit through the old tunnel, and once more they were forced to ferry the cars across the river.

Jan 1, 1995

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

By T. J. Fenner

Research conducted in South African mines has demonstrated the benefit of ground penetrating radar for the detection of geologic features and hazards. This is crucial for safety and production considerations in underground mines that are as much as 4 kilometers deep. This paper describes a new ground penetrating radar system designed specifically for high quality data acquisition, in the harsh conditions of deep underground environments, for use by operators with minimal geophysical experience. Design criteria included automated functions, intrinsic safety, light weight and minimal power requirements. Data is processed on the ground surface by geoscientists using a PC.

Jan 1, 1994

By Michael Michaylov, Elana Vlasseva

This paper presents a method for three-phase foam preparation recipe optimization. The pressurized foam is injected into porous media of gob area for prevention and fighting of SPONCOM fires. The method includes laboratory experiments for main foam properties as well as mathematical optimization procedure. Optimization criteria are formulated reflecting foam application purposes. The influence of solid phase on foam heat stability is shown. Results from optimization procedure for four foam agents by varying fly ash consistency of foam are presented. Theoretical basis for original construction of foam generator, specially constructed for of three-phase foam generation, is set u

Jan 1, 1997

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By R. J. Gary

Why would a company in its right management mind risk a fuel conversion program on a fuel that can't burn if it's too wet or too dry, too hot or too cold, too coarse or too fine, or doesn't have enough Btu's to supplement good combustion? On December 23, 1981, two months ago, we finished our first ten years of burning lignite -- this unconventional coal. It is from that experience that I am qualified to address you today. As some of you here probably already know, my company, Texas Utilities Generating Company, has pioneered the utilization of Texas lignite for electric power generation on a large scale, and I think it is fair to say that we have done this pioneering work largely on our own. Some of us feel like Noah did when he built the arc! I have titled this presentation "The First Lignite Decision" because our company was the first to make this major decision in Texas in the mid-1960's. It was a big decision, and at the time, perhaps a bold one. When you look at the conditions that existed in the mid-1960's, you can see why.

Jan 1, 1982

By G. T. Lineberry, B. R. Yama

Artificial intelligence research has produced several tools for commercial application. Some of the techniques that are widely used today include neural networks, fuzzy logic and expert systems. Artificial neural networks (ANNs) are excellent predictive, pattern recognition and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process-control applications. Modeling of spatial data, ore-reserve estimation, tunnel design, long wall-stability prediction and geologic roof classification are additional applications in which neural networks have been applied successfully. In this study, a standard back propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, the performance of the network is measured on an independent validation set. Results indicate a mean error of less than 1 % between the actual and predicted values. A neural network model was developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values for given coordinates. The neural network not only performed satisfactorily, but in some cases performed even better than the kriging model.

Jan 1, 2000

By A. D. Unsted

The Premier mine has been in existence for over 75 years and is closely woven into the glamour of the history of South Africa. A note on the geological formation of the diamond pipe and the gabbro gives a clearer overall picture of the mine. Mining methods for operations above and below the gabbro sill are briefly discussed. Ventilation arrangements for mining above the sill are briefly described and possible ventilation arrangements for mining below the sill are discussed in more detail. Note: conversions to S.I. units are not exact as rounding has been done.

Jan 1, 1980

By R. Balderrama Neder

A study consist in 20 column leach tests was performed for the "EI Arco" Copper ore deposit, located on Baja California, Mexico. The main purpose was to define the basic criteria like recovery and sulfuric acid consumption, for a commercial heap leach system design, to process the oxide Copper (Chrysocola) of the deposit. Leach parameters such as, amount of sulfuric acid in the cure solution, cure technique, particle size of the material, leach solution's flowrate application, leach solution's acid strength and height of the lifts, were evaluated to choose those parameters in which the results were the best ones for that particular design.

Jan 1, 1997

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By J. C. Emerick

Preliminary investigations have shown that wetland-based treatment systems can be an effective and relatively inexpensive control strategy for mine drainage pollution in eastern coal mining regions. This strategy also has potential for western mining regions, although too few systems have been installed in the west to permit general evaluation of the concept for western climates. The construction of prototype systems is encouraged for some situations. Wet-land environments have the capability of removing metals by natural geochemical and biological processes, including precipitation, filtration, ion absorption, and biological uptake and accumulation. Data presented for natural wetlands receiving mine drainage show removal of iron and other metals, and high accumulation of metals in soils and plants.

Jan 1, 1988

By Henry J. Jacoby

This report concerns Contract No. 3B of the Port Richmond Project, for the Department of Water Resources of the City of New York. It involves the construction of 7, 000 ft. of 7 ft. finish I. D. interceptor sewer by tunneling in soft ground, as well as associated manholes, regulator chambers, siphons and miscellaneous sewers and structures, beneath a heavily travelled perimeter road in Staten Island. The Contractor is Richmond Constructors, a joint venture of Grow Tunneling Corp., sponsor, MacLean Grove & Company, Incorporated, Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Project manager is Paul DeMarco, Vice-President of Grow Tunneling Corp. The cortract, as designed and bid, requires the use of liner plates 101 -0" O. D., and both cast iron and steel designs of several widths were included in the bid documents by the owner. The specifications also required the contractor to install and put into operating condition, prior to commencement of mining, a complete low pressure compressed air plant and all accessories for mining in compressed air, even though the contractor was given the option of using other methods of ground water control. A third requirement of the specifications was that a shield be used, either manual or mechanical, and with full provision for "breasting". BACKGROUND The first soft ground shield driven tunnel in the United States was in New York City and was built under Broadway in lower Manhattan in 1869

Jan 1, 1974

By David E. Thompson, Daniel J. Dobbels

INTRODUCTION The planning process for projects requiring construction of tunnels in urban environments can be highly complex and involves interaction with professionals of many disciplines. Typically the initial step in the planning process is to establish basic design criteria for the tunnel or tunnel system consistent with its intended purpose. Such criteria might include acceptable tunnel geometry, minimum and maximum slope or other associated criteria. Ideally, once the basic criteria have been established, the next step in the process might include establishing technically feasible horizontal and vertical alignment and shaft siting alternatives and developing "ball park" construction and operational cost estimates for the alternatives. Comparisons can then be made regarding the relative technical and economic merits of the alternatives and the most favorable alignment(s) are selected for further study or preliminary design. Typically the last and perhaps the most important task that is conducted during the planning stage includes identifying issues and potential problems to be addressed during the design and construction stages of the project. Many issues warrant consideration during the planning phase of a tunneling project. For the purposes of this paper, these issues can be divided into two broad categories: technical and non-technical. Important technical issues include, among others, general design criteria, geotechnical and geoenvironmental issues, and constructibility issues. Important non-technical issues include, among others, right-of-way and easement related considerations, project scheduling constraints, both short and long term environmental impacts and overall cost/benefit aspects of the project. With respect to influence on the planning process, these two groups of issues often cannot be separated completely. For urban tunneling projects, however, it is most often the case that the non-technical

Jan 1, 1991

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976