Search Documents

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By David W. Lillie, Pier A. Abetti

This paper reports on a study of the impact of fast growing new technologies on the market for copper over the next 15 to 20 years. The greatest threat is clearly the inroads of fiber optics on the traditional market for copper in communication cable. Opportunity areas identified include heat pumps, solar power and heat, desalination, electric vehicles and others. The overall impact of new technologies on copper is expected to be modestly positive if adequately encouraged by effective R&D.

Jan 1, 1986

By G. W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment®, two new lime substitutes for treating acid mine drainage (AMD), have been compared with lime and Allcament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with Environmental Protection Agency (EPA) regulations. Material utilization and optimum pH are reported.

Jan 1, 1988

By Reed S. C. Rogers

The most widely used machines for grinding coal to the sizes prescribed for the pulverized coal firing of furnaces, boilers, and kilns are the vertical ball-race, roller-race and roller-bowl types of mills. However, the increased use of coal has led to an increased use of tumbling ball mills for coal grinding. Specifically, air-swept ball mills are now a part of many dry pulverized coal firing systems, offering the advantages over vertical mills of lower maintenance costs and the ability to handle strong or abrasive (high ash) coals. The current use of wet ball mills is to prepare coal-water slurries for direct combustion, although in time they may also find routine application for preparing slurry feed for coal gasifiers. In either application, wet ball mills ofer the advantages that coal grinding and wetting can be accomplished in a single step, and that the mills are readily used with fine wet screens to assure top size control in the slurry product. The simulation of tumbling ball mills with mathematical models has reached a fairly advanced stage, but the concepts have been applied only recently to coal grinding. As this paper will demonstrate, however, significant progress has been made in the use of models in ball mill circuit design for coal grinding. Included is a description of the techniques used for simulation, recommended parameter estimation methods, and demonstrations of process engineering calculations for large scale coal grinding circuits.

Jan 1, 1986

By J. Edwards

A new, world class dump leach, solvent extraction, electrowinning plant for the recovery of copper comes on line in Chile. CODELCO-Div. Chuquicamata has added a new facility to their operations located in northern Chile. The plant demonstrates many unusual features including: underground collection of leachate, high copper tenors, extensive use of plastics and special corrosion resistant alloys.

Jan 1, 1989

By A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Jan 1, 1997

By James M. Barker, George S. Austin

Stone, one of the oldest building materials, today remains a well-established material throughout the construction industry. The use of natural stone is much less prevalent now than in the past. It is still widely considered to be the most aesthetically pleasing, prestigious, and durable building material. New and re-opened quarries are coming onstream to meet increased demand related to new building technology and increased residential use of stone. CLASSIFICATION No classification can completely eliminate overlap between dimension stone, aggregate, and decorative stone because most stone is multi-purpose. Many used for decorative purposes are not produced specifically for that end use. Rock otherwise considered waste in dimension stone or aggregate quarries can be decorative stone coproducts (Fig. 1). Many uses require a compromise between decorative and structural qualities (Bowles, 1992, written commu¬nication). Shipley (1945) used decorative stone interchangeably with or¬namental stone. Gary et al. (1972) defined decorative stone as that used for architectural decoration, such as mantels, columns, and store fronts, but added that it is sometimes set with silver or gold in jewelry as curio stones. Bates and Jackson (1987) also restricted decorative stone to that used for architectural decoration. Meanings of otherwise identical terms used in the stone industry differ be¬tween geologists, engineers, and quarriers. They often carry a much broader meaning for quarriers and engineers compared to their very specific use by geologists (Makens et al., 1972). Decorative stone, including ornamental stone, is more broadly defined by geologists as any stone used primarily for its color, texture, and general appearance. It is not used primarily for its strength or durability, such as construction stone, or in specific sizes, such as dimension stone. The decorative stone industry uses a much wider range of stone types compared to stone that is dimensioned. Decorative stone usually serves some structural pur¬pose, but is not load-bearing to any great extent. Weak or costly stones serve in decorative, not structural, applications. STATISTICS AND END USES Decorative and dimension stone data are difficult to separate because the US Bureau of Mines keeps statistics only on dimension stone and crushed stone. The value of domestic dimension stone production in 1990, which includes some decorative stone, was about $210 million compared to imports of about $524 million and exports of about $35 million. Production was 1 080 t of which at least one-third was for decorative uses (Taylor, 1992). The principal uses are rough blocks in building construction (23%) and monu¬ments (18%); the remainder is used as ashlar (18%), curbing (12%), and miscellaneous (29%). Major rock types are granite (50%), limestone (30%), sandstone (10%), slate (3%), marble (2%), and other (5%) (Harben, 1990). Crushed stone valued at $5.6 billion was produced in the United States in 1990 by 1700 companies operating 3400 active quarries in 48 states (Tepordei, 1991). About 52% is used in con¬struction, 9% in cement and lime manufacturing, 2% in agricul¬ture, 2% in industrial uses, and 35% for unspecified uses including decorative aggregate. Limestone and dolomite comprise about 71%, granite 14%, and traprock 8% of the stone crushed in the United States. The remaining 7% are, in descending quantity, sandstone, quartzite, miscellaneous rock, marble, shell, calcareous marl, volcanic cinder and scoria, and slate. The basic types of decorative stone are: rough stone, aggregate, cut or dressed stone, and manmade stone [(Table 1)]. Rough Stone Rough stone is used as it is found in nature with very limited processing such as minor hand shaping, edge fitting, and size or quality sorting (Perath, 1992, written communication). This stone type is often marketed locally in relatively small tonnages and includes fieldstone and flagstone. The primary end uses of rough stone are landscaping, edging, paving, or large individual stone landscape or interior accents [(Fig. 2)]. Fieldstone: Fieldstone is picked up or pried out of the ground (gleaned) without extensive quarrying and includes garden or large landscaping boulders (Austin et al., 1990, Hansen, 1969). Boulders and cobbles may be split or roughly trimmed for use in rubble walls and veneers, both interior and exterior. Popular fieldstone rock types include sandstone, basalt, limestone, gneiss, schist, quartzite, and granite, but many others are suitable. Much fieldstone is col¬lected by individuals or small companies because the industry is labor intensive and markets are small. The stone may be sold locally in small quantities from the back of vehicles (Austin et al., 1990). Fieldstone includes many rock types, sizes, and shapes with the only common denominator that it must be set by hand and be durable (Power, 1992, written communication). Moss Rock. Moss rock is fieldstone partially covered by algae, mosses, lichens, and fungi that give the rock an aged and variegated patina (Austin et al., 1990). The plants are supported by moisture and nutrients in the stone. Moss rock is used for landscaping, walls, and fireplaces. Although almost any durable rock can be a moss rock, most are slabby or rounded sandstone and limestone (Fig. 3). Flagstone: Flagstone or flagging consist of thin irregular slabs used for paving, walkways, and wall veneers. Random-shaped flagging is produced widely in the United States. Suitable stone

Jan 1, 1994

By Jamal Rostami

Continuous miners (CM) are the most popular underground mining machinery in soft rock mining, playing a dominant role in the production of minerals ranging from coal to evaporites while finding increasing use in salt and potash mines. Along with the ongoing technological advancements in the mining industry and the underground equipment, new generation of CMs offer several new features that are designed to enhance their operational capabilities and production rate. In addition to new bits and bit holders, one of the areas of improvement is the cutterhead design through computer modeling and simulation based on the full scale cutting tests. This paper discusses the state-of the-art CM technology and development of the computer models for design analysis and performance estimation of CMs. The general approach used in the modeling, along with the results of field trials for several projects will be presented.

Jan 1, 1998

By Alberto Tarsitani

The existing Rome-Florence railroad capacity is inadequate for the traffic volume. To increase this capacity and to reduce the traveling time the Italian National Railroad Administration has decided to provide an additional 400% of rail capacity. This new rail line will be known as the Direttissima Roma-Florence line. It is planned to operate the trains on this connection at speeds of 250 km per hr. Table 1 lists the main design characteristics. [TABLE 1. Design Characteristics Design speed250 km per hr Maximum inclination80 00 (0.8%) Minimum curve radius3000 m Minimum vertical curve radius30,000 m Maximum superelevation in curve 425 mm Type of rail60 kg per m welded] The new rail line will be connected to the existing one by means of high speed switches called "interconnections" so that parts of the new line can be used also by local trains. Construction works for this new line have been divided by the railroad administration into eight sections. Five of these have already been committed to joint ventures. Castiglione Tunnel is a part of the fifth section, 42 km in length, which has been awarded to Consorzio Ferrofir which is a joint venture composed of the construction firms of Astaldi - Di Penta - Lodigiani - Sogene.

Jan 1, 1974

By Phillip J. Maddex

During the last 10 years there have been many new developments in transport and handling equipment. Important technical and economic developments that can be used to reduce costs are; new terminal and materials handling concepts large river tows - 40,000 tons and 9000 hp towboats slurry loading and unloading of ocean vessels long distance pipelining of solids development of the shuttle train (unit train) large ocean barges ? 25,000+ tons ? pushed & towed 150,000 ton self-unloading super tankers - 300,000+ tons container shipping Some of these developments have been discussed at SME meetings in papers describing the transportation of minerals from new mines. But, only a few papers described improved transportation from older operations. Since transportation is a major part of the delivered cost for minerals, the economic benefits to be gained by putting new transportation developments to work are very substantial. Frequently good transportation planning and management makes the difference between a marginal ore body and a very profitable one.

Jan 1, 1972

By L. A. Puchkov, Mesentsev. V. K., I. O. Temkin

The problem of increasing underground mine ventilation efficiency is still of top priority. The complication of geological conditions with the depth of underground mining processes and reinforcement of requirements to technological and ecological safety are extorting the necessity of solving this complex problem with using of new information technologies. There exist different approaches to the ventilation problem. One of them, which the authors adhere to, is based on the concept of monitoring (under special mining and geological conditions-automatic control) of mining atmosphere and operative re-distribution of underground mining air among consumer , in accordance with the criterion of optimality [ 1.3 1. ] The set of tasks which should be decided in the frame of con- crete ventilation system depends on the peculiarities of deposit, technological schemes and so on. Nevertheless, some ventilation tasks such as: defining of ventilation network parameters; finding of dependence between these parametrs; operative redistribution of air streems, could be interpreted as universal ones. Main aspects of practical solving of different ventilation problems and their classification were investigated and considered in detail before [I ,2 ]. Some years ago we have began our investigations to develope quite simple and effective methods for decision of ventilation tasks on the base of neural network technology. It is well known that ventilation net, formed by various mine workings, is the main component of underground mining ventilation system. In general, network air distribution may be described by some functional F(Q,R,H), where Q- is a vector of air consumptions; H- is a vector of depressions; R- is a vector of airdynamic resistences. (Q,R,H) - are the informative entities , characterising every branch of the net. There exist some fundamental tasks which should be decided during the process of control of mining ventilation: calculating of natural air distribution Q = Q,{R, H,}, or Q = Q2(R, Q?}, where H, - is the maximal depression of the ventilation net, Q, - is the air consumption in the ventilation shaft; identifying of airdynamic resistance for some branches on the base either of air-depression removal or operative monitoring: [ ]

Jan 1, 1996

By Robert E. Mead

During the past three years the New York Trap Rock Corporation has been restricting blasting operations to days when favorable atmospheric conditions prevailed. By favorable atmospheric conditions is meant the absence of temperature inversions or isothermals in the lower atmosphere or under 6,000 feet altitude. Strong wind and wind shear can also cause conditions unfavorable for blasting. As a result of this practice, there has been a marked decrease in the number of blasting complaints received. The New York Trap Rock Corporation operates four stone quarries on or near the Hudson River within 60 miles of New York City. The Company supplies approximately 7,080,000 tons of high grade, crushed and graded aggregate, rip rap and by-products to the New Pork City area annually, This stone is carried to the market by a fleet of company owned deck &cows which are moved by tugs of a subsidiary towing company. Stone from two of the quarries is diabase: and, from the remaining two, dolomite.

Jan 1, 1962

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By L. Alan Weakly

This paper was presented at the ‘17th U. S. Symposium on Rock Mechanics’ on August 29, 1976, at Snowbird, Utah, at the SME-AIME Fall Meeting on September 1, 1976, at Denver, Colorado, and at the Polish-American conference on Ground Control in Room-and-Pillar Mining on August 7, 1980 at Southern Illinois University, Carbondale, Illinois. Introduction The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement- fly ash mortar. Although the fully bonded bolt concept is not new as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1)(2)the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation's Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since Decmeber of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the group-rebar system.

Jan 1, 1982

By A. Dale Wunderlich

In the past, most people have associated gold scams with the sale of non-existent gold mines, an undivided interest in unmined ore or the sale of gold-plated lead bars. These scams are still available to those who want to speculate. Now, though, the mining industry is plagued with a new type of con artist. Many of the new scams involve large, well established mining companies being victimized. Nearly all legitimate mining companies are in search of good mining prospects. This makes them susceptible to modern day con artists. Many professionals from the mining and petrochemical industries are out of work. Some of them have gotten involved with scams or activities that border on the criminal. Mining companies are losing millions of dollars each year to scams. Some of these scams involve venture-capital fraud. Some involve fraudulent mining proposals. And some involve unqualified individuals who are providing services by the precious metals industry. The author estimates that mining scams may be costing precious metals companies as much in dollar losses annually as employee theft. Employee theft is at an all time high, but so are gold scams. Since January of 1990, the au¬thor has been involved in gold theft investigations in which more than $1 million in gold product has been stolen by employees. In the past, most of the gold mine scam operators have concentrated on the general public, which is generally ignorant of basic mining procedures and practices. A scam artist would tell someone from your neighborhood that they have a wonderful underground mine. It produces 62.2 kg/t (2000 oz per st) of gold ore. Your neighbor might think that sounds like a very good investment. Those involved in the mining industry know better.

Jan 1, 1990

By Nes?e Çelebi

It has never been easy to finance within mining sector. Leasing may be an alternative source of finance for mining investments. Leasing is acquiring the right of usage for an asset for a definite period of time without having the ownership of it. In this study, a model for analyzing the lease financing opportunities for mining investments under risk and suitable for establishing a satisfactory leasing policy for both lessee and lessor is developed. Using the model, it is possible to obtain an expected equilibrium lease amount acceptable by both lessor and lessee and also the expected range of the equilibrium lease amount as a decision tool. First the existing leasing policies are mentioned, then the developed model is described. A case study is presented to illustrate the use of the model in establishing a leasing policy. In conclusion, the usefulness of the model is discussed.

Jan 1, 1992

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision making when considering a methane drainage system for an underground coal mine. A drainage system entails significant capital and operating expense; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision making are provided for an actual mine decision.

Jan 1, 1999

By S. Bentley

"Everyone has a general idea what mixing means, but describing the mixing process is not so simple. The objective of any mixing process is to distribute and blend the materials with different characteristics, different quantities as evenly as possible resulting in a homogenous mixture. Introducing proportional movement with the optimal intensity into the materials achieves effective homogeneous mixing results. A simple one directional movement with inadequate acceleration of the materials would obviously not achieve the same mixing results. This would be more like stirring than mixing. The amount of relative movement that is introduced is a decisive factor. Circumstances for successful mixing involve distribution of all materials, and achieving the highest probability that all recipe particles located in a specific position at the beginning can be found at any random location in the mixing chamber at the end of the process. This is the only way to ensure that a consistent result is achieved every time mixing is repeated.THREE-PART CYCLE The mixing cycle occurs in three phases; charging the mixer, the mixing process, and discharging. The sequence in which the individual materials to be mixed are filled into the mixer can have a huge impact on the efficiency of the mixing cycle. The mixing cycle overlaps the charging process and the discharge cycle follows the mixing cycle. To achieve optimum results, effective discharging methods should be taken into consideration to avoid risks of segregation. Costs for energy and wear should be as low as possible and finally, it is very important that the mixing cycle takes place as quickly as possible. In concrete or paste backfill production, selecting the best mixing technology is crucial for both the quality of the final product to be blended and the efficiency of the production process. The optimum mixing system is one that rapidly disperses all ingredients evenly throughout the mixing trough and completely surrounds all the course or fine aggregate particles with the slurry cement particles. Specific for paste production it’s the mixers job to also break-down unconditioned tailings to achieve consistent paste viscosity or measured spread. Many paste and concrete formulas also involve small quantities of chemical additives which also must be evenly distributed effectively. The time required per mixing cycle as well as the costs of energy, wear and maintenance will determine the economy of the concrete production."

Jan 1, 2015

By J. C. Yingling, V. Badaker, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

The University of Kentucky has developed reclamation cells at a surface mine in southeastern Kentucky to evaluate the impact of spoil handling (reclamation methods) and compaction alleviation methods on the physical properties of replaced growing media and on tree survival rate. From 1997 through 2001, penetration depth, penetration resistance, bulk density, and tree survival data have been collected at the reclamation cells and correlated to determine the relationships that exist between the soil physical properties at the site and tree survival. Regression models have been developed for each reclamation method evaluated using the collected data to predict tree survival rates on reclaimed surface mined lands as a function of the soil physical properties of the replaced growing media. Procedures have been developed for handling soil/spoil during reclamation that can minimize compaction in the replaced growing media. Procedures have also been developed for alleviating compaction in growing media on reclaimed and orphaned surface mined sites. These procedures, if implemented, will increase the potential for reforestation success. Finally, procedures have been developed for collecting soil physical property data for use in evaluating the suitability of spoil conditions for reforestation.

Jan 1, 2003