Search Documents

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By Mohammad Djavid

The one-pass tunneling pipe jacking method has often been the most schedule and cost efficient method for the pipe line installation. The main challenges in jacking pipes larger than 108 inches and for longer runs are: transportation and logistics, requiring high jacking forces, keeping line and grades, control of ground surface settlement, providing adequate external lubrication, and the potential of damaging the joints and pipe spigots. In recent years, 144" diameter pipes have been jacked for short runs of up to only 300 feet. In this article design and construction of installation of up to 1,000 linear feet run of 144-inch internal diameter, reinforced concrete pipes without intermediate jacking station in Chicago O?Hare International Airport are discussed. The article also presents discussions regarding the subsurface saturated silt formation, shallow cover, dewatering, jacking and receiving shafts, jacking forces, lubrication and settlement data.

Jan 1, 2008

By H. Walqui, C. Noriega

Southern Copper Corporation (SCC) is one of the world’s largest copper companies and is finishing the modernization of the Ilo copper smelter. A single ISASMELTTM furnace will start smelting 1,200,000 tons per year of concentrate at the end of 2006. Three existing Peirce Smith converters are being upgraded plus a new one for converting the matte to blister copper is being installed. Two new anode furnaces and a twin anode casting wheel have being operating since January 2006. This represents one of the main changes in the process because the final product of the smelter is now anode copper instead of blister copper. A new oxygen plant, acid plant, and others facilities are in the ramp-up stage. This environmental project will ensure that the new smelter will comply with the environmental regulations of Peru by the end of January 2007. This paper summarizes the background to the modernization project, describes the different stages of the project including engineering, procurement and construction, describes the main areas of the new copper smelter and also the pre-operational testing, commissioning and start-up of them. This is a brown field project with a target of reducing as much as possible the production losses of the existing operation. This paper presents the details of the development of the Ilo Smelter Modernization Project and explains the main aspects of the new facilities, the products to be obtained and the associated facilities for their commercialization, including a Marine Trestle for bulk acid exportation.

Jan 1, 2007

By Christian Maguire

Tunnel contracts in New York have in recent years had few bidders with the bids received being much higher than anticipated. Since 9/11, security has become a key issue in planning key infrastructure projects in New York. This is especially true in the case of large water supply tunnels. Striking the right balance between cost and security was the major factor in determining the best configurationfor the Kensico-City Tunnel. This paper outlines the efforts made to determine realistic probable bid costs for the tunnel contracts, and the innovative approaches taken to deal with security issues.

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By Joachim Klein, Frank Reimann

Nodular-graphite cast iron (GGG) is a material similar to steel, and one which exhibits excellent properties, in particular for components exposed to pressure. GGG cast iron has been used in many cases when sinking mine shafts with conventional tubbing. With linings made of cast iron tubbings (the backfill concrete is not integrated into the calculations, and merely serves as bedding) the properties of the cast iron can be made full use of, provided the tubbing is made to the appropriate cross-section. Calculations have shown that better static values can be arrived at when using cross-sections other than those of tubbings made to conventional German standard. The cross-sectional design of the new types of shaft lining made from GGG is to be developed on these lines irrespective of the cast iron structure being only stressed component or its restistance function being combined with the one of concrete. GGG 50 is used for the first time to make the reinforcing inner liner of a main shaft currently sunk in Germany. The physical properties of nodular-graphite cast iron, strength and deformability, suggest that, in the future, its application will not be restricted to shaft support but also in tunneling. New moulding techniques with better three-dimensional modelling resulted in new tubbing designs as installed e.g. for the Hannover underground at present. Shield-driven tunnels have to withstand earth and water pressure, apart from axial machine loads. In this field time is money as well. Therefore easy handling and quick installation are necessary for successful, use. Last but not least, safety is of first-order importance for work in shaft sinking and tunneling. Cast iron lining systems, accordingly, are adequate systems, in particular for excavations underneath water for transport systems and for goods and passengers.

Jan 1, 1987

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

By Myles E. Robinson

Significant changes in the markets for coal have taken place since World War II, As used in this study the term ?coal? will refer to bituminous coal, The anthracite industry in size, characteristics, and problems differs materially from the bituminous coal industry, These changes have both influenced and been influenced by the mechanization of mines, and by decreased distribution costs, especially in transportation. It is the purpose of this paper to examine these post-war changes, to assess their impact upon the production and distribution of coal, and to explore future market developments in the light of past and present trends and relationships. The layman lacks adequate informatian on the production, demand, and distribution of coal. There are two reasons for this. First, there is a relative lack of statistics coveting the industry, Coal operators and distributors are not required to file with any government agency the type of much more complete statistics filed by the railroads and public utilities with national and State agencies. The Bureau of Mines assembles much useful information on the coal industry, but several areas, including that of investment and finance, have no central depository which can be used to keep the public informed of the nature and extent of the industry and its problems.

Jan 1, 1964

By P. Schmieder

"The close vicinity of mining companies to other sites that are used for commercial and residential purposes or to areas under conservation as well as the fact that the people become more and more sensitive to emissions have led to a negative attitude towards mining operations in the neighborhood. It is above all the use of drilling and blasting techniques that give rise to objections, in the course of which demands for more environmentally-friendly production methods have been voiced. It is in this context that production methods without the use of explosives are considered as an option. After all, the use of such production methods is the only alternative for some quarry operators. The question is what are the true benefits of these techniques and what is the relation between a possible improvement of the environmental effects on the one hand and the technological potential as well as the costs on the other. It is intended to assess the mining techniques for solid rock in their entirety. This paper will therefore look at the aspects for assessing mining techniques in the context of their environmental impact and the costs."

Jan 1, 2005

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By J. M. Ekenes

New approaches that increase hydrometallurgical recovery from refractory minerals in below-mill-cut-off-grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyrite-bearing ore at Freeport-McMoRan?s mine in Morenci, Arizona. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation.

Jan 1, 2012

By V. G. Grechanyuk

The paper presents the mechanical properties of Cu-Mo composite materials depending on the molybdenum content. The influence of structural defects on the mechanical-physical properties of the condensates at stretching testing as well as of the lamellar grain dimensions upon the mechanical properties of Cu-Mo composite materials is also presented.

Jan 1, 2008

By Michael Taylor, Thomas W. BoBo

Currently two of the most important characteristics of construction aggregates are (a) the particle size distribution (psd) and (b) the “shape” of the aggregate particles. The long established test methods and standards for these properties require substantial resources and most suppliers can take samples and conduct tests at intervals measured in days (psd) or even months (shape). Furthermore these tests require time: so the results are available only after material has been stockpiled or shipped. In the rare cases where problems are found the out-of-spec material has often been shipped to points unknown. There are substantial advantages to be obtained if the psd and other geometrical properties could be obtained from the material as it moves through the production processes and if the results could be reported back within seconds or minutes to Plant Control Managers. This paper describes a single on-line system used to evaluate production of crushed material in a production quarry. The system consists of an enclosure (containing the camera and lighting etc.) mounted over a production belt. Images are fed by fiber optic cable to a nearby control room where the data are analyzed; stored; displayed; and made available for integration into a process control system. Numerous forms of display can be created according to the needs of the producer. Once programmed by an automation engineer all functions of operation are fully automated. The system has permitted over 400 tests per hour with a feed back time less than 2 seconds. Sufficient geometrical measurements are made so that many different “shape” factors can be computed on a similar time scale. The paper summarizes the results from approximately 100 shifts of about 8 hours each and compares the imaging method with the current standard hand methods. Study of the data generated showed that, when combined with additional plant information, the system can be used to generate additional useful control information.

Jan 1, 2005

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007