Search Documents

By Carson Rife, Michael L. Clark

INTRODUCTION Zortman Mining Inc. is a wholly owned subsidiary of Pegasus Gold Corporation of Spokane, Washington. Pegasus has been producing gold and silver from the Zortman and Landusky mines since 1979. The Zortman and Landusky mines are two distinct open pit mines located approximately 6 kilometers apart in the Little Rockies Mining District of north central Montana. The two mines use large-tonnage, low- grade heap leaching techniques to efficiently process the gold and silver ore. PROJECT DESCRIPTION The Little Rockies rise abruptly 914 metres from the surrounding plains to about 1829 metres above sea level. The topography is quite steep, making efficient leach pad construction a major challenge. The climate is semi-arid with moderate summers and occasionally severe winters. Freezing temperatures usually arrive in late October or early November, influencing the effectiveness of leaching operations. GEOLOGY AND MINERALOGY The geology of the Little Rocky Mountains consists of steeply dipping sedimentary ridges forming an elliptical dome surrounding a core of intruding syenite porphyry. Within the syenite porphyry are well fractured and mineralized shear zones where the existing reserves and open pits are located. The ore is presently divided into oxidized, mixed, and sulfide. Only the oxides and mixed zones that are of ore grade are placed on the leach pads. The syenite porphyry host rock enables effective leaching of gold and silver to depths of 61 metres, having a major impact on leach pad construction costs. MINING All mining since 1979 has been by contractor. This enabled initial mining to commence without capital investment in equipment. Through competitive negotiations, Pegasus has been able to keep contract mining costs at levels very close to what would be experienced if Pegasus had purchased equipment initially. Contracts are negotiated yearly and are based on a unit price and haul distance for ore and waste. Haul distances have ranged from as little as 457 metres to as much as 3,050 metres. At present, Pegasus is developing a 27,000,000-tonne leach pad at the Landusky project that is adjacent to the minine area. This design feature will reduce the mining cost by 20 percent over the life of the mine. In 1987, over 5,900,000 tonnes of ore and 3,200,000 tonnes of waste will be mined at the Landusky project. Through 1986, 13,763,000 tonnes of ore have been mined at a waste-to-ore strip ratio of 0.60:l at the Zortman project, and 13,005,000 tonnes of ore at a waste-to-ore strip ratio of 0.79:l have been mined at the Landusky project. Current mining reserves are 32,769,000 tonnes of ore at a waste- to-ore strip ratio of 0.59:l. Through efficiencies of large-scale heap leaching, Pegasus has been able to lower the mining cutoff from 0.34 grams per tonne gold to 0.27 grams per tonne gold. This has reduced the mining cost per tonne of ore h percent through a reduction in strip ratio of 14 percent. Beginning in 1984, all pits were designed based on computer-generated "floating cone" pits. The geologic models were developed by Pegasus staff with a series of economic models evaluated. The resulting computer-generated pits were used as a guideline in designing the mine plans, including haul roads for final calculation of tons and grade. Input to the floating cone models consisted of mining cost, processing cost, cutoff grade (0.34 grams gold per tonne), recovery (67 percent) and gold price. Due to the gold being deposited primarily on the fractures of the syenite host rock, no crushing of ore is needed prior to leaching. This characteristic of the ore is a key in being able to profitably mine and process gold ore at an average grade of 0.69 grams of gold per tonne. Strict blasting control is also a key in success of the leaching operation. A system of splitting ore and waste in blast patterns has been devised to reduce dilution. Also, drill hole spacings are varied from 3m x 3m in breccia ore to 4m x 4m in syenite ore to 5m x 5m in waste. Drill holes

Jan 1, 1987

By W. C. Hellyer

The Granduc ore body is located beneath glacial terrain on the borders of British Columbia and Alaska, some 600 miles from Vancouver and 30 miles from Tidewater at Stewart, B. C. The concentrator and attendant facilities are located in wilderness country at an elevation of 2500 feet. The average annual snowfall is 65 feet. Surface facilities and ore body are linked by a 10 mile railroad haulage tunnel. This copper property has been developed by Granduc Operating Company on behalf of Newmont Mining Corporation and American Smelting and Refining Co. First production started in November, 1970. In August, 1966, Granduc Operating Company awarded an engineering and construction management contract to McKee-Swan Wooster, a joint venture of A. G. McKee of Canada and Swan Wooster Engineering Company Limited, to design a concentrator to treat approximately 7000 tons of ore per day. The isolated location of the Granduc ore body indicated comparatively high freight rates on consumable items of concentrator supplies such as reagents, grinding media, etc. A firm flowsheet for the flotation of the Granduc ores having been developed by the Danbury laboratory of Newmont Exploration Limited, attention was devoted to means of reducing operating costs. One obvious method was to reduce or eliminate the costs of steel grinding media by employing some form of autogenous grinding. two pilot plant operations were carried out at the facilities of Lakefield Research of Canada Limited, in which autogenous grinding of Granduc ores was investigated. The results of these investigations led to the selection

Jan 1, 1972

By Malcolm J. Robinson

Over 80% of Australia's population lives within 200 km of the coast, 70% in 10 major coastal cities. Potential cement raw materials are widely distributed but deposit size, quality, transport, market and environmental considerations are important in determining economic value. Major production locations are in a variety of geological environments ranging from Lower Paleozoic crystalline limestones to Tertiary and Recent polyzoal limestones and limesands, both onshore and offshore. Raw material transportation is by road, rail, sea, aerial ropeway and pipeline; road/rail transportation of the finished product is traditional but movement by sea of clinker and cement is increasingly a feature of the industry.

Jan 1, 1982

By James E. Brewer

Procedure for approval by the U. S. Army Corps of Engineers of a new source of aggregate is in three phases. Phase 1 consists of an investigation of a quarry or proposed quarry by district geologist and laboratory geologist and/or petrographer. The quarry face or suitable outcrop is logged in detail or, if exposures are poor, cores may be taken to determine whether further investigations are warranted. Phase 2 consists of thorough laboratory testing. Cores and crushed material are subjected to a number of acceptance and quality tests for soundness, absorption, abrasion, reactivity, and other properties. Petrographic analysis is also made. Phase 3 is a physical and economic study of the site and involves determining quantity of stone avail- available, amount-and character of overburden, condition of haul roads and distance to rail shipping point, plant flow sheets and capacity, aggregate sizes produced, and approximate price of material at plant.

Jan 1, 1966

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964

By E. De Souza, J. F. Archibald

"Many underground mines use cemented backfill to mitigate environmental effects associated with tailings disposal. The large energy needs associated with mine backfilling and cement production operations create significant CO2 and Greenhouse Gas Emissions. This paper introduces post-consumer glass as an alternate, equally effective and lower cost binder agent strategy for cement in backfill that may be implemented to assist in reducing solid waste production, lowering energy costs, and restricting Greenhouse Gas Emissions. Extensive engineering testing, consisting of pipe flow loop tests and strength tests, has been implemented in order to demonstrate the technical feasibility of process integration within industry. An economic analysis has demonstrated that glass is competitive in cost relative to cement and a socioeconomic study has further indicated that the utilization of glass in mine backfill would create a new market for waste glass that requires less processing and reduces costs."

Jan 1, 2005

By J. D. Miller, C. L. Lin

As the techniques and resolution for three-dimensional spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional X-ray microtomography offers a unique imaging capability. Spatial resolution on the order of 10 µm can be achieved with the use of microfocus X-ray generators. Recently, a state-of-the-art cone beam X-ray microtomography system was installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility was designed to obtain 2,048 by 2,048-pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind instrument can be used to obtain three-dimensional spatial reconstruction for many applications, such as three-dimensional liberation analysis, pore structure analysis of particle beds during filtration and the air-void system of concrete structures. The utilization of X-ray microtomography not only allows for the quantitative analysis of multiphase systems but also allows, for the textural characterization and determination of phase continuity. This paper presents information regarding the current use of this new facility and a review of potential applications for the advanced analytical system. Key words: Cone beam X-ray microtomography, Three-dimensional analysis, Material characterization

Jan 1, 2003

By Adrian J. Mathias

For many years excavations were made in rock exclusively by conventional blasting methods, and without concern for damage to the rock surfaces which remained after the excavation was completed. Recently, however, there is an increasing awareness for the importance of making rock excavations with as little damage as possible to the remaining rock surfaces; consequently, several revolutionary new precision blasting techniques have been developed during the past few years. These techniques, variously known as cushion, smooth- wall, perimeter, pre-shear, and pre-split blasting, basically involve the creation of a fracture plane in the rock between a series of blasted holes. The variations in each of these techniques are largely due to the differences in hole diameters, hole spacings, methods of charging, and sequence of blasting used to achieve certain specific results. The development of these precision blasting techniques was initiated by Canadian Industries Limited in 1953 at the time the Sir Adam Beck No. 2 Hydro-electric Project was under construction by the Hydro-Electric Power Commission of Ontario. Since then, these techniques have been somewhat advanced, and they have been applied with varying degrees of success to a number of projects. These projects include railroad and high- way cuts, dam spillway channel excavations, canal excavations, tunnel driving, shaft sinking, and other underground applications.

Jan 1, 1965

By J. Sattarvand, P. C. Augustine

Despite significant safety improvements, the mining industry remains one of the most hazardous occupations globally and the evacuation of Miners, when an uncontrollable incident occurs in the mine, is the best bet to saving lives. However, Human factors/behaviors during an emergency are likely to influence the evacuation performance. Other industries have made a significant effort to determine these human factors that can impede evacuation performance, however, the current state-of-the-art in mine evacuation or self-rescue is that the evacuation route is predetermined, and a static sign is used to direct miners to the predetermined safe location. This method is limited in representing actual conditions that arise in a real emergency, neglecting the different behaviors displayed by humans. As optimization of the evacuation of a mine plays a fundamental role in emergencies and modeling evacuation behavior and movement of miners is a complex task, this research utilized Agent-Based simulations to simulate the evacuation behavior and performance. It was observed that people with the smart evacuation device made fewer mistakes and arrived at the safe place in less time compared to those have no access to the device. The Mathematical model used in optimizing the shortest path to a safe place is also explained in this paper.

Jun 25, 2023

By V. Duddempudi, B. Goertz, J. Brune, G. Bogin, F. S. Barreto

"INTRODUCTION In designing a new pneumatic Dust Sampling Device (DSD) for coal mines, it was essential to analyze the air and particle flow inside the device in detail using Computational Fluid Dynamics (CFD) modeling. Several CFD models were developed to simulate the air and dust flow and sample collecting process of the DSD. These CFD models were developed to assist in the design of the DSD instrument prototypes for laboratory testing. Nozzle and injection parameters such as geometry, air velocity and pressure, were varied across a wide range to obtain the optimal settings to accurately simulate the fluid dynamics of the multi-phase flow within the DSD. Accordingly, these parameters were used as a guide for the design of the DSD and to verify the dust scouring dynamics, which is designed to represent the dust entrainment during an actual methane or coal dust explosion. BACKGROUND The 2010 explosion at the Upper Big Branch mine has demonstrated the destructive violence of a coal dust explosion. A major contributing factor for this disaster was that the mine operators did not have a reliable, direct-reading method to collect mine dust and determine inert content and combustibility. This led to the development of a new prototype handheld, pneumatic mine dust sampling device (DSD), which blows a puff of air and entrains the mine dust by mimicking the entrainment process during a mine explosion. A computational Fluid Dynamics (CFD) model is used to analyze the air and dust flow inside the DSD. The objective of the CFD modeling effort is to find the optimum design of the DSD prototype, nozzle orientation, air pressure and pulse length by analyzing and varying these parameters so that the scouring action collects a valid, representative and repeatable mine dust sample. CFD MODEL DESIGN Figure 1 shows a wireframe image of the DSD which is utilized in the setup of the CFD model. The DSD has a triangular cross section and is 10 cm wide. Two nozzles with cross-sectional dimension of 2.8 cm by 0.25 cm act as inlets at the narrow end of the triangular cross section. The CFD model includes a reference plane 6 cm away from the nozzle to measure the quantity of dust collected. The geometry shown in Figure 1 was created for the model and it matches with the design of the actual device shown in the figure 2. Symmetry, along the plane X-Y through the center of the device, is used to reduce the number of computational cells in the CFD model. Figure 2 shows the prototype device used for experimental testing. CFD MODEL SETUP Figure 3 shows a hexahedral mesh with a cell size of 0.8 mm and the total number of cells is around 650,000. The ANSYS Fluent® pressure based solver with a transient case was used with a total duration of 40 ms. The 40 ms simulation time is based on experimental measurements to capture the injection of air and initial scouring of dust."

Jan 1, 2016

By J. F. Edwards

In situ extraction of copper through borehole injection presents a new technology for the mining of copper. For the successful application of this technology, copper recovery at the surface must be specifically designed for borehole injection and the general conditions of the well field. This paper describes the design of a solvent extraction / electrowinning facility specifically designed for in situ leaching of copper. This design is based on commercial solvent extraction / electro-winning with considerations of the requirements of this specific application.

Jan 1, 1988

By C. G. Carlström

The total iron ore production in Sweden in 1969 was 33.3 million metric tons. 31.7 million tons were exported mainly to Western European countries. 27.8 million tons (87 per cent) originated from the mines at Kiruna, Svappavaara and Malmberget, located just north of the Arctic Circle in Sweden. Planned production for 1970 is 25 million tons during 10 months, due to a strike at the beginning of the year. Present production plans for the next five years expect an annual export capacity around 33 million tons in 1975, including 5.7 million tons of pellets. The mining and shipping at the loading terminals of Narvik on the Atlantic coast and Luleå at the Gulf of Bothnia are managed by LKAB - a 96 per cent state-owned company. 4 per cent of the share capital is owned by the private Grängesberg Company. The railway - 106 miles from Kiruna to Narvik and 130 miles from Malmberget to Luleå - is operated by the State Railways in Sweden and Norway. Comprehensive expansion of the Narvik ore port will be carried through during the next five years to increase the annual shipping capacity to at least 35 million tons and meet the development of rapidly growing ship sizes.

Jan 1, 1970

By Michael V. Wolski, Ryan O. McCarter, Kenneth A. Johnson

"The Central Subway is Phase 2 of the San Francisco Municipal Transportation Agency’s (SFMTA) Third Street Light Rail project and will extend the existing Phase 1 initial operating segment from its current connection to the Embarcadero line at Fourth and King streets along Fourth Street to Market Street, under the Bay Area Rapid Transit (BART) and Muni Metro tunnels and then north beneath Stockton Street to Chinatown (Fig. 1).Total new track to be constructed as part of the Phase 2 work consists of approximately 734 m (2,410 ft) of surface track and 2,636 m (8,650 ft) of tunnels. The tunnels were constructed as twin, singletrack bores by two tunnel boring machines (TBMs) (Johnson, 2014) moving north from the southern end of the launch box under the I 80 freeway between Bryant and Harrison streets. North of Chinatown Station the TBMs continued another approximately 683 m (2,240 ft) to a retrieval shaft near Columbus Ave. at Washington Square. The project also includes five cross passages to connect the two tunnels, and three underground stations (the Yerba Buena/ Moscone Station, Union Square/Market Street Station and Chinatown Station.)Excavation of the twin tunnels was performed with two TBMs, with both TBMs driving northward from the launch box. TBM excavation was performed such that the location of the machines was staggered to separate the active excavation faces by a minimum of 91 m (300 ft) between headings. This minimum separation was maintained until the first TBM arrived at the retrieval shaft plug, at which time the separation requirement was relaxed.Excavation began with the “southbound” (SB) tunnel which will ultimately accommodate the southbound TBM light rail trains followed by the second TBM in the “northbound” (NB) tunnel. With the completion of the drives in June 2014, cross passage excavation then began and was completed in April 2015. Overall, construction of the Central Subway tunnels was a success considering the nature and complexity of the project. Additional details of the completion of the Central Subway tunnels are presented in another paper from the RETC 2015 conference (Leong et al., 2015)."

Jan 1, 2015

By John S. Summer

The induced polarization (IP) method of geophysical exploration is capable of detecting even small amounts of metallic luster minerals in a rock mass. Consequently, in the years since discovery, IP surveying has become the most popular ground geophysical survey method. It is not too difficult to understand many applications of IP surveying as used in the search for mineral deposits. However, the basic theory of the IP phenomenon is not well developed or understood, and there has been some disagreement on fundamental concepts. In order to most effectively apply the IP method in the field it is necessary to know the physical characteristics of the sought-for deposit including its size, shape, depth, and electrical properties. With this information an optimum IP search arrangement can be devised and one could use the best possible electrode interval, type of array, and line spacing. With uncertain target characteristics as encountered in the real world, geological guidance must be used to help direct an optimized IP survey.

Jan 1, 1972

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By R. W. Seedsman

Mandalong Mine was originally planned to operate with panel widths of 250 m and a predicted surface subsidence in excess of 3 m. The consent conditions applied by the NSW government on this mine plan were very tight and, following a change in ownership, were considered by the new operator to present a number of unacceptable business risks An acceptable risk profile for the mine layout restricted surface deformations to less than 500 mm vertical subsidence, less than 7 mm/m tilt, and less than 5 mm/m strain. Empirical subsidence prediction methods indicated that it would be necessary to reduce extraction panel widths of 80 m - an uneconomic option. The application of a number of rock mechanics concepts identified that the local overburden geology could be exploited such that panel widths of up to 175 m could be possible. The 125 m width was selected as a low-risk introduction of this new subsidence prediction method. The extraction of the first 2 longwall panels has demonstrated the validity of the prediction subsidence method and has provided the opportunity to refine the selection of key input parameters. The impact of mining through a zone of thrust faults was successfully predicted. The mine is now planning the introduction of 160 m wide panels, and will review the associated subsidence impacts prior to any further increases in width.

Jan 1, 2006

By M. T. Atwood

For more than sixty years the rich oil shale formations of Colorado, Utah and Wyoming have been evaluated as a future source of petroleum. After many false starts the commercial production of shale oil is near. Union Oil and Colony (Exxon and Tosco) have begun construction of commercial plants. Occidental and Rio Blanco (Gulf and Standard of Indiana) are well along in the development of modified in situ (underground) processes. A number of other companies and groups are in advanced stages of development. This paper will review some of the major elements involved in the production of shale oil with emphasis on means available to express the efficiency of production of pyrolysis liquids and gases from oil shale rock.

Jan 1, 1982

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By Victor F. Hollister

This first section of case histories of mineral discoveries, Vol. 3, covers some of the milestones in porphyry copper and skam exploration successes. It was during the era of these discoveries that large, complex exploration departments emerged as permanent adjuncts of large mining companies. The discoveries helped shape how and where exploration activity was conducted. Probably the most important factor in exploration success is management. Few management people are mentioned in this section or in any exploration history, yet the distinction between success and failure ultimately rested with the decisions they made. One of the most successful groups was initiated by Roger Straus and Herbert Brownell when they sought to make Asarco into an important metal producer. Relying on Clem Pollock and L.H. (Bill) Hart to identify and push worthwhile projects, the Asarco management remade the company. Asarco will benefit from exploration successes com- pounded by that team for years to come. Duval is an example of a management that decided to add metal production to its industrial minerals output. When Page Morris was president, that company opened three major porphyry copper mines and became an important factor in metals. Under the Monis management team, Duval became a leader in exploration. At the other end of the scale are managements that snatched defeat from the jaws of victory and by so doing changed the character of their companies in other ways.

Jan 1, 1991

By Robert W. Bartlett

Both hydrometallurgical and vapometallurgical processes often involve ores that have been previously ground and size classified. When the valuable mineral is substantially liberated, the chemical reaction is likely to occur on the particle surface and the particle core will shrink as the reaction proceeds. If the chemical reaction products are solid materials then a solid shell, usually porous, will form around the shrinking core. This is known as the core/shell or topochemical reaction model. Using a spherical approximation for the particles, equations have been developed to express the extent of chemical conversion of the particle, depending on which one of the following process or mass transport steps is rate controlling:1 (1) chemical reaction at the particle surface, (2) diffusion through the thickening reaction product shell or (3) mass transport through a boundary layer surrounding the particle. In a previous paper2 these equations were coupled with the Gates -Gaudin-Schuhmann equation 3 4 describing the distribution of particle sizes resulting from comminution of rocks and other brittle solids to develop reaction yield curves expressing the weight fraction of metal or other valuable component of the feed that was chemically converted as a function of residence time. This was done for (a) batch, (b) continuous plug flow and (c) continuous back-mix flow (continuous stirred tank) reactors or process vessels. To make the curves of general rather than special utility, the residence time (average residence time for back-mix reactors) was normalized to a dimensionless time by dividing by the time required to completely chemically convert the largest particle in the feed to reac-

Jan 1, 1972