Search Documents

By Madan M. Singh

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." Implied in the constraints of Section 516(b)(1) of SMCRA is a determination of what constitutes "material damage" to surface structures, renewable resource lands, and the capacity for sequential land use following underground mining. The authors have already briefly addressed the subject of damage criteria in relation to surface structures (Bhattacharya et al, 1984). In this paper, an attempt is made to provide quantitative guidelines to ascertain material damage to renewable resource lands, although the data available to establish these criteria are considerably more limited than is the case for surface structures. Besides, many more variables influence the severity of the impact at a given site, making the task of assigning stringent ground movement limits even more complex. This often necessitated use of professional judgement and occasional reverting to a qualitative approach. Hence the reader is cautioned at the very outset that the quantitative limits presented herein are approximate and are primarily intended to serve as rough guides for ascertaining the extent of damage to the renewable resource lands under consideration, and that depending on site-specific conditions the actual damage incurred may differ significantly from that predicted by the proposed criteria. The authors, however, feel that the criteria suggested are somewhat conservative, but realistic. The actual damage observed should generally be less severe than predicted by these criteria. It may also be clarified here that the term "subsidence", as used in this paper, implies the total phenomenon of surface and subsurface effects associated with the mining of minerals and not only the vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35 percent), ceramics and glass (32 percent), lubricating greases (9 percent), air treatment (5 percent), continuous casting mould flux powders (5 percent), polymer production (4 percent), primary aluminum production (1 percent) and other uses (9 percent) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014).In the 1990s, the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced during this period were consumed in the glass, ceramics and aluminum industries. In the 1980s and 1990s, there were two major lithium operations in the United States: brine operations at Silver Peak, NV and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, NC. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period, it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994).Lithium is still produced from the brine operations at Silver Peak. But in more recent years, Chile has become the world’s leading producer of lithium carbonate from brines. Australia has maintained its position as the world’s largest producer of lithium mineral concentrate, the majority of which is exported to China to produce lithium carbonate and lithium hydroxide (Jaskula, 2014).A spodumene concentrate was also produced at the Tanco Mine in Manitoba, Canada beginning in the 1980s through to 2010 when lithium operations were suspended due to fluctuations in the lithium market price (Martins et al., 2013)."

Jan 7, 2017

By R. S. C. Rogers

A mathematical model is proposed as a general formulation for the analysis and simulation of once-through crushing machines. Methods are described which can be used to estimate parameters of the proposed model from experimental data, thus minimizing reliance on backcalculation. The applicability of the model is demonstrated in the analysis and simulation of laboratory and full scale double roll crushers, and with evidence given for a laboratory scale cone crusher. An extension of the model for closed circuit crushing is also described.

Jan 1, 1984

By K. A. Natarajan, K. S. N. Murthy

Growth of Thiobacillus ferrooxidans on pyrite mineral surfaces and in 9K leach media was studied through estimation of bacterial protein in the different phases. Bacterial attachment was found to be governed by particle size of the mineral, period of incubation and by stationary or agitation conditions used during incubation. Increased bacterial growth in the liquid as well as on the solid phase was observed with decreasing particle size and increasing incubation periods. Increased bacterial attachment to pyrite mineral surfaces was observed to promote iron dissolution.

Jan 1, 1993

By T. R. Raponi, D. Barnes

The Williams Mine mines and mills 6000 t/d (6600 stp’d) of gold ore using SAG/ball milling, leaching and CIP, electrowinning and refining. Electrowinning, high-pressure cathode washing, filtering, retorting and refining are based around the use of knitted stainless steel mesh cathodes. Their primary advantage over conventional steel wool cathodes is that electrowon gold can be washed off and the cathode can then be reused. Typically, the knitted cathodes have a useful life of up to 15 months. Gold production of up to15 t/month (50,000 oz/month) is easily processed with this system. Presented is a description of this operation, including a review of the equipment and performance data.

Jan 1, 1992

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By Emily Wortman-Wunder

Attendees at December?s Arizona SME Section Conference at the Hilton El Conquistador Resort outside of Tucson, AZ were feeling optimistic and ready to get to work after a year of steady growth and recovery in the mining industry. During the two-day event (Dec. 5-6, 2010) and the preceding American Mining Hall of Fame banquet and awards ceremony, the focus was on copper, worldwide population growth and regulatory pressures, with several smart new projects featured alongside updates to traditional large-scale copper development projects. Keynote speaker Timothy Snider, chair of the University of Arizona?s Lowell Institute for Mineral Resources, hit the mood of cautious optimism when he analyzed the global demand for resources, using the case example of copper. Over the next 20 years, he said, the world?s population is expected to grow to 9.2 billion and the average annual per capita copper use is expected to rise from 2.2 to 4.5 kg (5 to 10 lb). The increase in demand will provide tremendous opportunity for mining companies, he said, but cautioned that the opportunities are balanced by negative influences on demand and pressures on supply. While demand for copper is currently growing, Snider noted that there were significant downward pressures on demand as well. These included a western world that is overbuilt, in-creasing use of substitute materials in new construction and the rise of wireless devices. He also noted new regulatory pressures, and pointed out that resource development now had to occur within a context of sustainability on several levels.

Jan 1, 2011

By R. W. Salmi

The authors discuss the cooperative efforts by Minnesota Ore. Operations and Research; from the earlier development, testing and installation of fine shear screens in the Minntac Step III concentrator to the most recent testing and operating data that has resulted in the installation of Derrick Multifeed sandwich deck screens in Minntac Steps I and II. Pilot-plant test results that were obtained at the Coleraine, Minnesota Research Laboratory are also reported and demonstrate the effects of feed rate and feed percent solids on sandwich screen performance with two sizes of Minntac fine screen feed.

Jan 1, 1984

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By David E. Sims

Asarco has been using computer-aided open-pit mine design since 1966. The in-house developed program package includes drill-hole analysis programs, interpolation routines, and three-dimensional open-pit design programs. The financial analysis step after pit design required that a reasonably accurate schedule be produced so that a good cash flow model could assess the feasibility of a project. The manual method of scheduling was too time-consuming for feasibility work, so a computerized scheduler was required. Since no computerized mine scheduling programs existed, we requested proposals from consulting firms to develop such a program. The selection of a consulting firm, the formulation of the contract and design specifications required about three years to accomplish. The consulting firm, Systems Control Inc. (SCI), of Palo Alto, spent over one year doing the programming and testing alone. The details of the program development were reported in "Computerized Year-by-Year Open-Pit Mine Scheduling," SME-AIME Transactions, December 1974. In June of 1973 the program, which SCI dubbed Optimum Resource Extraction or ORE, was installed. Version 1 of ORE was utilized successfully on three separate properties over a period of two years. During this time it became obvious that some of the original design specifications were restrictive, and certain modifications were required. The ORE program was submitted for modification, and after one year version 2 was operational in May of 1976. The program now consists of approximately 20,000 lines of FORTRAN source statements grouped into 190 subprograms, and runs in a 450K region of Asarco's 370/148 in Cranford, NJ. The Tucson com¬puter (370/115) is tied to the Cranford computer via a 9600 baud leased T.P. line, for running mine scheduling and other large mine planning programs.

Jan 1, 1979

By Yuji Tsuneno, Yoshikazu Mikami, Yasuo Takeuchi

A new device was successfully developed in order to overcome the difficulty of drilling longer holes for anchors in soft soil bedrocks or swelling bedrocks, which is one of the major impediments to rapid excavation by NATM (New Austrian Tunnelling Method). With higher rotation (1200 - 1800 r.p.m.) and lower percussion energy (4 - 6 kg.m), the new drill has following advantages: (1) Applicability covers soils and medium hard rocks with the same drifter. (2) Longer hole (more than 9m) is achievable only with air flushing even in cohesive soils or rocks. (3) Better borehole stability is obtainable even in earth or in fissured rocks.

Jan 1, 1981

By J. A. Baicker

A 2 1/2 inch diameter probe containing a high resolution gamma ray spectrometer was developed for downhole ore grade assays to depths of 6,000 feet. Tests have been conducted on the characteristics of this tool for in-situ determinations of uranium by means of natural gamma ray counting, and of copper, silver, gold, iron and coal quality by means of neutron-induced gamma rays. Application of the technique for improved carbon-oxygen logging in oil fields is promising. The probe contains a cryogenically cooled high purity germanium detector and a 4,000 channel spectrum analyzer. Gamma ray spectra are digitally transmitted up the cable to the truck-mounted data processing system. We found that uranium can be assayed directly in different types of formations independently of the degree of geochemical disequilibrium by counting the relatively weak 1.001 MeV gamma ray of protactinium-234m. Neutron activation work shows that in-situ determinations of copper, silver, iron and coal quality are technically feasible. In carbon-oxygen oil well logging the technique allows an accurate determination of carbon, oxygen, hydrogen, chlorine, silicon, calcium and iron, and shows promise of providing an improved oil/water differentiator.

Jan 1, 1982

By P. Somasundaran, J. T. Kunjappu

Spectroscopic techniques are becoming increasingly popular for characterizing the interior of adsorbed layers of surfactants and polymers at solid- liquid interface as well as in the identification of com- pounds on mineral surfaces. This review encompasses the application of fluorescence and ESR spectroscopic techniques to reveal the microscopic environment of the adsorbed layers of surfactants and polymers on minerals with a special reference to the adsorption of anionic surfactants (e.g., sodium dodecyl sulfate) and polyelectrolytes (e.g., polyacrylic acid) at positively charged mineral (e.g., alumina) - water interfaces. Finally, the utility of XPS and auger techniques to identify the surface elemental composition of different mineral species has been related to their flotation efficiency.

Jan 1, 1987

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By Daniel R. Walton

This paper covers several points of interest to mine engineers and planners involved in evaluating or conducting geostatistical coal reserve estimates. In particular, the ability to optimize borehole drilling locations and minimize drilling costs is addressed. Also discussed is the concept of confidence intervals for estimated coal characteristics obtained through geostatistical estimates and their importance in decision-making for mine planners. Finally, a discussion is presented on how geostatistics enables identification of invalid data points and actually forces strict attention to data editing and proper geologic interpretation.

Jan 1, 1982

By M. Li, J. D. Miller

Recently water insoluble alcoholic solutions of alkyl hydroxamic acid collectors have been shown to be particularly effective in the flotation of coarse feed material sampled from phosphate operations in Florida, North Carolina and Utah (Miller et al., 2000). The experimental results indicate that high separation efficiencies can be achieved in single stage flotation with these new collectors. In some cases the concentrate grade reached 34% P2O5 with 93% recovery from single stage bench scale flotation experiments. Critical aspects of the composition and structure of these new collectors are discussed with respect to their effectiveness in phosphate flotation. The wetting characteristics at fluorapatite, francolite, dolomite and quartz surfaces are being investigated with the new collector. Finally, other surface chemistry considerations in the development of these new collectors for phosphate flotation are discussed.

Jan 1, 2002

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994