Search Documents

By M. K. Gangal, E. D. Dainty, G. Kunchur

This paper presents a validation of C02 as a single surrogate measurement for other diesel-emitted pollutants in multi-diesel-machine operations typical of small underground mines. This means that the simple measurement of C02 alone can be used to estimate the concentrations of other components of diesel exhaust in the mine environment. The linear relationship of C02 concentration with other diesel-emitted pollutants was indicated by the results of simultaneous real-time monitoring of C02 with CO, NO, NO2, SO2, Respirable Combustible Dust (RCD), and Air Quality Index (AQI) in several small underground mines. The SO2 was not directly measured but calculated from the measured C02 concentration and diesel fuel analysis for carbon, hydrogen and sulphur. The measurements were made in the return air drift under various mining conditions involving a number of diesel LHDs and haulage trucks. The statistical analysis and mathematical representation of the several components of diesel pollutants with C02 are presented. Regression analysis shows that at the 1 percent level of significance there is a strong linear relationship of these diesel pollutants with C02. This relationship is discussed in detail, concluding that C02 measurement alone is a good indicator of overall mine air quality and can be used as a control parameter.

Jan 1, 1991

By B. C. Paul, R. Q. Honaker, M. Huang

Froth flotation is now, the most commonly used method for cleaning fine-coal fractions in coal-preparation plants. Past research and industrial practice have demonstrated that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, the efficiency of froth flotation decreases sharply as the concentration of middling particles increases. This is due to the flotation of high-ash particles that have a small amount of hydrophobic coal present at the surface. Because gravity-based processes are much more efficient for the treatment of middlings, the application of centrifugal washing for fine-coal cleaning was studied with an emphasis on the primary cleaning of fine-circuit feed. Results are shown of a parametric study that used a semibatch Falcon centrifugal concentrator. The results of the study revealed that separation performance is a function of particle size, bowl geometry, feed solids content and feed rate.

Jan 1, 1996

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By Robert L. Bates

In this paper I use the term "industrial minerals" in its broad general sense, and I distinguish two main groups. The first consists of the bulk materials, characterized by low unit price, nearness of deposits to markets, relatively simple methods of extraction and processing, and a tendency to be closely related to the construction industries. The second group includes those materials valued for exceptional purity, or for some special property such as hardness, immunity to acids, or dielectric strength. These materials are produced in smaller amounts, at high unit values, from deposits notably restricted in. distribution; and they require more or less sophisticated methods of production and beneficiation. The applications of this second group are not closely tied to any particular part of the economy. From the way in which the commodity committees of the Industrial Minerals Division are set up, I take it that the chief interest of most members is with the first group of materials mentioned above. Hence this paper will deal mainly, though not exclusively, with such bulk commodities as sand and gravel, clay, and stone. The first word in the title of the paper also requires brief explanation. It is here given a threefold interpretation. First is the role of the industrial minerals themselves in industry; this would probably be taken as the conventional meaning of the title* The second is the role of the industrial-mineral producers as citizens of the community. The third is what may be called the scientific role of these producers.

Jan 1, 1964

By J. W. Leonard

Since the interpolation of exploratory data 1 can be no better than sampling procedures, a series of field experiments were conducted in an effort to determine whether hand-cut channel or core washability determinations best represent continuous miner produced run of mine coal. By obtaining a core drilled to within a few feet of channels taken from an underground face and then overmining both locations; core, channels and run-of-mine coal allocations were obtained from a common sample and all allocations were subjected to identical washability determinations. In order to compare results, basic rules2,3 previously anticipated and later published by the writer were employed. The first rule states that "For any full seam washability determination, the sulfur versus ash function for increasing cumulative specific gravity float coal fractions is linear". The second rule states that "For any full seam washability determination, the recovery versus ash function for increasing cumulative specific gravity float coal fractions is logarithmic".

Jan 1, 1988

By Z. Abdel-Khalek, Hassan El-Shall, S. Farrah, C. Boice

Selective adsorption and surface modification of minerals by surfactants is the primary step in the process of separating certain minerals with similar physical and chemical characteristics in the flotation process. In this study, microorgan- isms are used as surface modifiers for francolite and dolomite. Results of adsorption experiments with francolite and dolomite show that the microbes selectively adsorb to one of the minerals under specific operating conditions. In preliminary flotation experiments, it is found that the microorganisms enhance or depress flotation of the minerals leading to an increase in the efficiency of separation between the francolite and dolomite. The conditions leading to selective adsorption (surface modification) and subsequently to possible efficient separation of these two minerals are discussed in this paper.

Jan 1, 2002

By T. J. Harvey, W. van der Merwe, J. Joubert

GeoBiotics, LLC and Kumba Resources (Pty) Ltd are jointly developing the GEOCOAT® heap bioleaching technology and downstream processing technology for recovery of zinc from tailings at the Rosh Pinah Mine in Namibia. This paper outlines the development of a computer simulation for the bioleaching of sphalerite and the downstream processing. Computer modeling has shortened the product development cycle by allowing many flowsheet scenarios to be analyzed negating much of the expensive and time consuming laboratory testing. A model was developed using the Limn® system which is an Excel® Add-In flowsheet drawing and solution engine. Given that most engineers are familiar with Excel® this software is extremely easy to use and has less hidden calculations making model verification much easier.

Jan 1, 2003

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By Stephen P. Harrison

The ventilation of coal mines has long been a major challenge for the mining industry. Prior to the 1969 Health and Safety Act, mine ventilation planning was almost entirely handled by individuals in mine operations and engineering who had extensive practical experience. Their background and expertise was sufficient to deal with existing ventilation problems and planning. A recent decline in the number of qualified individuals combined with more stringent state and federal regulations have necessitated a thorough engineering oriented approach to ventilation in mine planning design. To plan for an existing mine, a thorough ventilation survey must be conducted to determine the capabilities of the existing ventilation network. A ventilation survey also provides considerable useful data for long range planning. Essential information such as friction factors, entry resistance, and potential ventilation problem areas is gained from the survey data. With this information a comprehensive computer analysis can be conducted to evaluate alternative mine plans. This evaluation of mine plans is essential to minimize the number of shafts required while still maintaining the quality of mine ventilation. Using an existing mine as an example, this paper outlines a detailed procedure for organizing, con-ducting, and evaluating a ventilation survey. In addition, specific ventilation problem areas are isolated and alternative methods for their solution are considered. Furthermore, a long range mine plan is evaluated and the most feasible variation of the plan is selected.

Jan 1, 1980

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

The U. S. Bureau of Mines, through a contract research program with Foster-Miller, Inc., has identified guidelines for the selection of the most effective water spray system and water flow rates for use on continuous mining machines. Specifically, these parameters were modified to obtain maximum dust control with regard to quartz dust exposure and more stringent respirable dust standards due to quartz. A novel water spray system, consisting of flat fan spray nozzles, mounted across the top of the mining machine, along with high flow, flat fan and higher pressure hollow cone nozzles mounted under the boom has been identified and tested. The anti-rollback/underboom spray system minimizes dust rollback while increasing dust knockdown by its unique positioning of spray manifolds and orientation of spray nozzles. Respirable dust suppression characteristics of the system acted in three ways: - by wetting the surface of the broken coal material to prevent dust from becoming airborne; - by controlling the airflow pattern at and near the face to minimize dust rollback to the operator Is control location; and - by dust knockdown, i.e., airborne capture, or scrubbing of airborne dust from the air. During underground trials, the anti-rollback/ underboom spray system reduced dust levels at the operator's position and in the immediate return by 55 and 15 pct, respectively, when compared to a conventional spray system. Quartz dust levels at the operator '8 position were essentially eliminated, while quartz dust levels in the immediate return were reduced by 57 pct. Applying the concepts of this technique throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable quartz dust, as well as allow coal mine operators to comply with the associated, more stringent, respirable dust standards.

Jan 1, 1987

By Gerrit V. R. Goodman, Edward F. Divers, Charles D. Taylor

Future mining systems will possess the ability to cut from crosscut to crosscut where advances could exceed 30.5 m (100ft). However, limitations arise when ventilating such mining systems. In deep advance mining, there will be no workers at the face to manually advance ventilation tubing or curtain. Additionally, traditional methods provide no means for maintaining face ventilation after the miner backs out. Problems such as these have suggested the need for innovative ventilation methods compatible with deep advance mining systems. The Bureau of Mines is currently considering a number of innovative ventilation schemes. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Previous testing in large metal-nonmetal mine entries showed that jet fans provided adequate face ventilation for deep advances in large headings. Current testing will determine the application of jet fans in ventilating smaller coal mine entries. Another approach considered compatible with deep advance mining will use either exhausting or blowing tubing that can be remotely extended from crosscut to crosscut. During the mining cycle, such a device would extend automatically as the miner sumps into the face. The Bureau of Mines is considering several different operating designs using this tubing.

Jan 1, 1991

By K. L. Bickel

Catalyzed diesel particulate filters (CDPFs) are used for reducing diesel particulate matter (DPM) concentrations in underground mines. The U.S. Bureau of Mines is conducting research on how catalyzed diesel particulate filters perform. Two CDPFs, with two different catalysts, are used on vehicles in two mines. The CDPFs are periodically removed from service and evaluated in the laboratory to determine their DPM collection efficiency, regeneration temperature, and effects on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions. This report summarizes the results of the laboratory evaluation, and the mines' experience with the CDPFs. Both CDPFs have operated over 2,000 h. One was evaluated after 1,646 h; its collection efficiency at one operating condition was 87.3 pct. After 2,135 h of operation it was removed from service because it was damaged. The second CDPF continues to be used after 2,328 h of service. The laboratory evaluation indicated its collection efficiency decreased after 1,584 h of use and its regeneration temperature increased from 405' C to 420' C. The mines' experiences with the two CDPFs varied. While being used on mine vehicles, both CDPFs became plugged with DPM on a number of occasions because of insufficient regeneration. CDPFs are capable of lowering DPM concentrations in diesel exhaust. They can also lower emissions of CO and HC, depending on the type of catalyst used. In this study, the performance of the CDPFs changed with use. Recommendations are given in this report for proper use of CDPFs in mines.

Jan 1, 1994

By C. A. Rowland

Introduction Rod mills are horizontal, cylindrical, rotating, tumbling mills in which steel rods, that are usually about 6 in. shorter than the length of the grinding chamber, are used for grinding media. Fig. 33 shows a cutaway view of a rod mill. Rod mills were first used around 1910 because of their ability to grind in open circuit, consistently produce a uniformly sized prod¬uct, give greater continuous availability, and give lower maintenance costs. They have basically replaced roll crushers and coarse grinding ball mills in comminution flowsheets. The present 20-ft limit on rod length, based on rod manufacturing methods, and the pulp flow char¬acteristics, that influence mill capacity, have established the maximum rod mill sizes' of 15 x 21 Vs ft using 20-ft rods and drawing from 2,200 to 2,300 hp. Rod Mill Uses. The principal uses for rod mills are: preparing feed for ball or pebble mills, grinding gravel or aggregates to the size analysis required for making concrete sand, preparing coarse agitator feed for leaching operations, and for primary grinding circuits, particularly in industrial mineral applications. Wet grinding is the most frequently used grinding process for rod milling. There are a few special cases where dry rod milling is used. Preparing feed for ball or pebble mills is the most common use for rod mills. In ferrous and nonferrous ore concentrators, wet open-circuit grinding is used to prepare ball-mill feed. Figs. 34 thru 37 show the four basic grinding circuits used in these concentrators. In rod mill-ball mill grinding circuits, where the rod-mill discharge contains 25% or more of the grinding circuit product-size material, the rod-mill discharge can be fed to the ball- or pebble-mill classifier as shown in Fig. 34. This is the most frequently used rod mill-ball mill circuit in the nonferrous ore concentrators. In a few concentrators such as Anaconda's Weed concentrator,55 the rod mill discharges to one classification stage which makes the same or a slightly coarser particle-size cut as the classifiers used to close the ball- or pebble¬mill circuits, as shown in Fig. 35. In concentrators where rod mill-ball mill circuits are used to grind low grade magnetic iron ores such as Reserve Mining Co., Silver Bay, Minn.; Erie Mining Co., Hoyt Lakes, Minn.; Eveleth Taconite Co., Forbes, Minn.; US Steel, Mt. Iron, Minn. and Atlantic City, Wyo.; Inland Steel-Jackson County Iron Co., Black River Falls, Wis.; and The Cleveland-Cliffs Iron Co., Adams mine, Kirkland Lake, Ont., the rod mills discharge to rougher magnetic separators (cobbers), the concentrates from which are fed to a ball milling stage as shown in Fig. 36. The same basic circuit is also used with gravity concentra¬tion methods such as spirals (Hanna Mining Co., Groveland, Mich.), tables (St. Joe Minerals, Bonne Terre, Mo.), and jigs. When the rod-mill discharge contains less than 25% of the grind¬ing circuit product size, this indicates an ore that does not readily produce the fines needed to help carry the coarse feed into the ball charge. When this occurs, the fines in the rod-mill discharge are needed in the ball mill or pebble mill so the rod-mill discharge flows direct to the second-stage mills as shown in Fig. 37. Rod mills are used to make feed for open-circuit ball mills such as those used in wet grinding cement raw material (American Cement, Brennan Ave¬nue plant, Detroit, Mich., and Port Huron, Mich., plant, and at the South Dakota State Cement plant, Rapid City, S. Dak.). Grinding gravel or aggregates to the size analysis required for making concrete sand is used in areas where natural sand of the proper particle size gradation required to make concrete is not availa¬ble. Three-quarter inch crushed aggregate is ground to 4 mesh using center peripheral-discharge rod mills (Fig. 38) operating in open circuit. US Corps of Engineers specifications state that the sand product be 93-100% passing 4 mesh and contain no more than 3-7% passing 200 mesh. It may be necessary to classify the rod-mill discharge to remove any excess -200 mesh sand produced in the rod mill. Particu¬larly when processing aggregate with high abrasion indices, center peripheral-discharge rod mills are used instead of hammer mills, fine bowl crushers, and crushing rolls for the production of specification sand. If the -4 mesh size fraction of the rod-mill feed is removed

Jan 1, 1985

By M. P. McArthur

General mining practices at W. R. Grace's Bonny Lake mine are much the same as those used in open pit phosphate mines in Central Florida, except for the difference in the depth of the overburden which introduces many variations, From 1945 to 1961 the mining at Bonny Lake has been from an area in which the overburden averages from 55 to 60 feet and in several locations exceeded 65 feet. The matrix thickness will average 15 to 18 feet for the areas mined. As you can see from the above depths a total hole depth will average from 70 to 75 feet.

Jan 1, 1962

The "Gold" chapter of my adventures did not start with a rush. On May 14, 193 1, Thayer Lindsley wired me asking if I could examine the Pioneer mine in British Columbia right away. I replied, "Yes," but I had never heard of the Pioneer and, although many others were asking about gold during the Depression, none were doing anything about it. A little later another wire asked me to meet Gen. A.D. McRae in Vancouver in a couple of days. This was the start of 20 years of intermittent examinations for Lindsley. I took the train to Seattle and the night boat to Vancouver where I met Gen. McRae and his associate Victor Spencer. McRae had been one of the Canadian leaders during World War I and, for his services, he had been made a Canadian senator, a lifetime job. Col. Spencer was proprietor of a big store in Vancouver, and almost as distinguished. A seaplane was waiting for us in the harbor, to be piloted by Major McLaren, one of the leading Canadian flyers during the war. He flew us up the long fjord of Howe Sound and then on north along the route of the provincial-owned Pacific Great Eastern Railway past jagged snow-clad peaks to the village of Shalalth on Seton Lake. A rental car run by Curley Evans, a noted British Columbia character, was waiting for us in Shalalth and it took us for 50 miles over one of the steepest and crookedest roads I had ever seen. At the end of the road the Pioneer camp was set in a deep canyon in the Coast Range. Dave Sloan, another British Columbia character, was waiting for us and he immediately took me underground, at nine in the evening, to see the Pioneer ore. The ore body was then a small one but it was running over an ounce of gold per ton. The name Dave Sloan became synonymous with Pioneer. McRae and Spencer told me the history of Sloan arid the Pioneer on the way to the mine. The rich surface ore had first been discovered about 1879. It was then far inside the almost trackless wilderness of the beautiful

Jan 1, 1976

By Keith Jones, Martin Knights, Timothy Watson

In 1996 a KBR (Brown and Root) led international JV was appointed to design and supervise an underground and surface package. The design of 6 km of tunnels, plus enlargements, deep shafts in glacial and sandstone deposits for the conversion of the existing LEP underground laboratory at CERN, Geneva adjacent to the Jura Mountains/Lake Geneva had to be undertaken in an operational environment and in conjunction with other underground constructions associated with the US$3bn refurbishment.

Jan 1, 2003

By R. Tanaskovic

Unfavourable climatic conditions in stopes are of significant economic and social importance due to the following reasons: - Working effect is much lower leading to decreased output and work productivity disregarding implementation of mechanization. - Manpower operating capability decreases much faster under unsatisfactory climatic conditions. Under normal climatic conditions a workman would expend much less effort in line with a shorter effective time for the achievement of identical production effects since the work would be more efficacious. The objective of study of problems and climatic conditions is to make the working environment in mines suitable for normal development of operations. Lowering of mining works to increasing depths and winning of a growing number of small orebodies over a broad area makes the problem of creating suitable climatic circumstances more complex. Mining costs are growing due to bench conditions in line with decreasing metal content in the ore, so frequently the investments required for creating favourable climatic conditions represent, in addition to the selection of mining technology, a very important parameter when making decisions regarding exploitation. As known, the basic factors affecting climatic operating conditions in mines-are: temperature, humidity and speed of air flow, implying that the climatic operating conditions are closely related to mine ventilation. Usually, the concept of unfavourable climatic operating conditions includes increased mine air temperature and humidity and low air flow velocity so that heat exchange between human organism and the working environment is impeded or reduced to minimum. Metal mines in Yugoslavia are characterized by the existence of a large number of active faces - stopes and horizons and lowering of mining operations to increasing depths, so that face ventilation solutions are more and more complex. Since its foundation (1961), our Institute is engaged in investigation of factors influencing climatic circumstances improvement of calculations for air distribution and distribution control in complex ventilation networks and study of problems related to ventilation of large volume and irregular configuration faces, as well as application of gained knowledge in our mines. The paper presents the knowledge and experience gained in the case of Lead and Zinc Mine "Trepca" - Stari Trg.

Jan 1, 1980

By G. Rinelli, Paul R. Jr. Smith

Preparation for flotation begins with dragline mining, pumping, washing, screening, and desliming. Slimes, nominally -150 mesh material, constitute large quantities of phosphate and water which are a disposal problem. Older techniques involve sizing at about 35 mesh for separate coarse and fine treatment. The plus 14 mesh fraction does not require concentration. Coarse treatment includes agglomerate spiralling, belt flotation, thickening, scrubbing with sulfuric acid, de-oiling for reagent removal, and cationic flotation of fine quartz. A recent trend is to screen at coarser than 35 mesh size and eliminate coarse particle treatment, sacrificing some grade of this product. Techniques for flotation concentration of the fine size fraction are discussed.

Jan 1, 1976

By Ernst P. Hall

As a scientist and an engineer whose responsibilities include the consideration of air pollution and its control, I am frequently called upon to answer variations of two basic questions, These questions may I be set forth as: (1) How much air pollution does the coal industry cause? (2) How serious is the air pollution problem to the coal industry? At first these questions may seem elementary and almost trite, but serious consideration of them will show that they are technologically involved and I further complicated by the subjective base to which they must be evaluated.

Jan 1, 1963

By S. K. Kawatra, V. Claremboux, S. Valluri

Carbon dioxide capture from coal-fired power plant flue gas and subsequent sequestration is expected to play a vital role in mitigating global climate change. To meet the growing need for CO2 capture Technology, Michigan Technological University is researching CO2 capture and Utilization. We have successfully converted CO2 into oxalic acid using an electrochemical approach. If oxalic acid can be produced in bulk from CO2, it can be used to leach rare earth minerals at low cost. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. In this paper, we will present an idea of how the factors mentioned above will effect the electrochemical reduction of CO2 to Oxalic acid. INTRODUCTION. CO2 is thermodynamically quite stable, as shown by its highly negative heat of formation. Thus, it is expected that the formation of any useful chemical from CO2 will require the input of at least as much energy as geological sequestration. However, to be more effective the resulting economic value of the chemical need only pass the cost of the additional energy required beyond geological sequestration. This lends itself to two extremes: one where the quantity of energy required is low and one where the economic value of the additional energy is low. It is expected that CO2 can be reduced via electrolysis to several compounds. Of particular interest are formic acid, oxalic acid, methanol, ethanol, formaldehyde, and carbon monoxide (as a component to syn-gas). These chemicals have been reported as electrolytic products previously in literature and have considerable potential for application. EXPERIMENTAL Electrocatalytic Production of Oxalate from CO2 We are using membrane electrolysis cell to produce oxalate from CO2. A membrane electrolysis cell is a 2-chamber electrolysis cell where the chambers are separated by a selectively permeable membrane. To produce oxalate, a cation exchange membrane (which selectively exchanges cations) was used. Previous literature suggests that in the cathode chamber an organic electrolyte, such as tetraethylammonium perchlorate or tetraethylammonium bromide in dimethylformamide, are preferred3. In the anode chamber, a sodium hydroxide solution water is used. Carbon dioxide is then bubbled into the cathode chamber as a current is applied.

Jan 1, 2019