Search Documents

By Richard L. Bullock

At the beginning of the previous chapter, variation in the types of room-and-pillar stopes were briefly identified so that the reader could begin to understand the extensive application of this mining system. These same variations will be reviewed and elaborated upon in this chapter while discussing the methods by which the material is extracted. FULL-FACE SLICING BY DRILLING AND BLASTING When the entire mineralized thickness is taken in one pass of mining, it is known as full-face slicing. There is no mineral of economic value intentionally left either in the floor or the back. Theoretically, there is no limit as to how high the face could be in a single pass. But there are practical limitations to equipment size, pillar stability, and control of local loose slabs on the face, roof, and pillars that dictate current practices. The range of face height of the 15 typical room- and-pillar mines covered in Table 8 (Sec. 1, Subsec. 7) from the Dravo report, 1974 was 1.7 m (5.5 ft) to 9.8 m (32.1 ft), the average being 5.2 m (17.1 ft). In the Gaspe copper mine, Murduchville, Que., the drill jumbos were constructed with an extendable tower for full-face mining up to 15.2 m (49.9 ft) if necessary. However, a more common practice at that mine is to take the ore in multiple slices (Hall, 1959). In many metal mines the normal practice when starting stoping is to drive a single development drift into the ore zone a distance that will allow at least four or five rooms to be opened on each side of the initial drift. Since this opening will probably serve as the main haulage drift, it should be kept as straight and as level as possible. As to the other criteria for the stope developments, it might be well at this point for the mine planner to review the remarks presented earlier (Sec. 1, Subsec. 7) on drifts, entries, and crosscuts for production. After the initial drift is driven, it should be slabbed to the full room width if it is not that wide already. Next, the future pillars should be marked on the ribs and the rooms driven between them. If the ore extends beyond the length of the initial drift and is to be mined in the normal sequence of mining, care should be taken in a random room-and-pillar system to see that the extension of the initial roadway remains straight. If pillar "spotting" is left to the shift foreman or to the miners, they probably will not realize the importance of maintaining a uniform pillar line next to the roadway, and of keeping the line straight. Invariably, a pillar will end up in the middle of the future drift extension resulting in a "dogleg" in a possible main haul- age road. While this error is not catastrophic, too much weaving in and out of pillars will certainly slow down future production haulage and needlessly increase costs. Face or Breast Drilling and Blasting Practices To drill and blast the initial advances into the rock, usually some form of cut pattern must be used. In room-and-pillar mining, when a pattern is drilled in a face and that face is the only exposed surface to which all of the rock must be broken, the pattern is known as a "face round" or "swing." The face to which the rock must be broken is referred to as a "free face." Thus the most common way to advance a room into virgin rock with only one free face is by drilling swings. If, after breaking around a pillar, taking down back, or taking up bottom, there is a second (or third) face exposed, a group of holes drilled nearly parallel to a free face and breaking to it is known as a "slab round" or "slabbing." In some mining districts it is also known as "slashing." Obviously, because two faces exposed offer less resistance to fragmentation than a single face, slabbing requires less drilling and fewer explosives than required to break the same tonnage with the same degree of fragmentation with swings. Therefore, it behooves the driller (or supervisor) to plan the combination of

Jan 1, 1982

By J. C. Draper

The Duquesne Light Company and GAI Consultants, Inc. conducted a demonstration program aimed at establishing permanent vegetative cover directly on acidic, deep coal mine refuse. Several plots were treated with formulas varying in soil amendment application rates and plant species. Periodic monitoring of refuse chemistry has indicated when maintenance applications of seed and soil amendments were required. To establish drainage control, the site had to be regraded. The most successful formula was applied to the entire site. Specific treatment for acidic spots has been initiated. Results of the program indicate that adequate permanent vegetation has been established.

Jan 1, 1983

By Basil S. Fee

INTRODUCTION Probably the most important family of chemicals used in mineral processing today is a category of basic commodity chemicals loosely denoted as pH regulators. Typical chemicals which are referred to as pH regulators include lime, magnesium hydroxide, soda ash, caustic soda, ammonia, sulfuric acid, and hydrochloric acid. These chemicals are often used in very significant amounts in almost all of the major mineral processing operations such as flotation, hydrometallurgy, etc. (in dosages up to ten pounds per ton of feed ore treated). While cheaper in cost per unit weight of chemical than more specific chemicals such as collectors, frothers, extractents, etc., the overall cost to the mill operator is generally higher with pH regulators per ton of ore processed than with any other given processing chemical. For example, a rough rule of thumb in sulfide mineral flotation is that the cost of lime is double that of the collector(s) used. The symbol pH is used to designate hydrogen ion concentration. When acids, salts, and bases are dissolved in water, individual molecules are dissociated into their constituent radicals or ions. The strength of an acid or a base increases with the extent of such dissociation or ionization. An alkaline solution is one in which the number of Qydroxyl ions (OH ) exceeds the hydrogen ions (H ). In an acid solution, the hydrogen ions predominate. In either case, both ions are always present as water itself ionizes to a limited extent, that is: [ ] The pH scale is logarithmic and the pH value is the negative of the logarithm (base 10) of the molar concentration of hydrogen ions per liter of solution. For example, a pH of 5 means that the molar concentration of hydrogen ions per liter is 0.00001 (1 x 10-5). Likewise, a pH of 9 means that the molar concentration of hydrogen ions per liter is 1 x 10-9. Normally, the relationship between hydrogen ion and hydroxyl ion concentration is based on the relationship: Concentration of H ion x concentration of OH- ion = constant. Eq. (1) In dilute and/or moderately concentrated solutions that are normally used in mineral procygsing processes, the constant at 25°C is 10-14. On the pH scale, the value of pH equal to 7 represents the hydrogen ion concentration of a neutral solution. pH values lower than pH 7 indicate increasing acidity and higher values than 7 indicate alkalinity. Table 1 shows the nature of the pH scale at 25°C. Temperature affects the extent of ionization of dissolved acids, salts, bases, and water so that the hydrogen ion concentration (hence pH) of a solution is also affected by temperature. As a means of demonstrating this dependency, Table 2 shows the change of the exponent of the constant (base 10) in Eq. 1 and the pH value corresponding to neutrality as a function of temperature. It is also important, for example, that alkalinity or acidity expressed by pH not be confused with total alkalinity or total acidity. For example, total alkalinity is commonly determined by titration with a standard acid solution (usually HC1). pH is a measure of the hydroxyl ion concentration of an alkaline solution, whereas titration is a measure of an alkaline solution's acid neutralizing capacity. Thus, if one takes a series of various alkaline solutions prepared using different chemicals but all of exactly the same pH (and temperature) and then subsequently carries out a titration on each solution with a standard acid, it would be observed that the various alkaline solutions would neutralize entirely different amounts of acid. As an example, 0.08 grams of caustic (NaOH) , 6.32 grams of soda ash (Na2CO3), and 8.17 grams of ammonium hydroxide (NH4OH) all have a pH of 11.3 at 25°C. One liter of each of the above solutions neutralizes 0.073, 4.348 and 8.496 grams of HC1, respectively. Therefore, depending on the specific use of any given pH regulator, special tests need to be run by the mill operator to determine factors such as: the specific technical goals to be accomplished by

Jan 1, 1986

By Francisco A. Fonseca

The Carajás Hills are in Brazil's Eastern Amazon, between the Araguaia and Xingu rivers, and parallels 5° and 7° Latitude South. A location map is given in Fig. 1. It is an area of low mountains (maximum altitude 900 meters), covered by the Amazon rain forest. Annual average temperature is 25°C, ranging from 31°C (maximum) to 19°C (minimum). Annual rainfall averages 2,000mm. Although it rains throughout the whole year, heavy rains occur from December through March. At the beginning of the 20's, Brazilian explorationists made brief geological descriptions of the area. Due to the thick soil, scarce fresh rock outcrops and the tropical forest covering a completely unpopulated area, detailed geological studies were difficult and reconnaissance expeditions were limited to the river margins.

Jan 1, 1982

By Karl A. Smith, Roger T. Johnson, David W. Johnson

Conflicts are common in the mining industry. Engineers are accustomed to addressing issues such as land use, air and water pollution, and health and safety. Although conflicts of interest are important in the industry, they do not have the impact on organizational decision making that controversy does. Controversy is a type of conflict, probably the most important type, for effective decision making and competent problem solving. It exists when one person's ideas, information, preference, choices, conclusions, theories, opinions, or perspectives are incompatible with another's and the two seek to reach an agreement (Johnson and Johnson, 1979). Interpersonal and intergroup controversy is prevalent in the day-to-day functioning of organizations. If constructively managed, this type of controversy has important implications for effective decision making and problem solving. Too few organizational members accept controversy, and almost none attempt to stimulate it. This is because too few of them understand controversy well enough to accept and use it effectively. Most organizational personnel lack the interpersonal skills needed to stimulate controversy and manage it effectively. Discussion of conflicting ideas may not be common in problem solving situations due to the fear and anxiety most people feel in conflict situations. Traditionally, organizations suppressed conflict. They believed it was avoidable, caused by management errors. Optimal organizational performance required its removal. Conflict, though, is inevitable. And optimal organizational performance requires a moderate level of conflict. Management should manage the level of conflict and its resolution, for optimal performance. The current view stresses the importance of controversy for learning. Confronting a person with a different point of view stimulates that person to gather more information to elaborate, justify, or provide rationale for their position. Controversy: Process and Outcomes The decision making process begins with participants categorizing and organizing current information and experiences so that a conclusion is derived. When participants present their conclusions to another group and realize their conclusions are being challenged, a state of internal conceptual conflict or uncertainty ensues. This uncertainty motivates the challenged group to actively search for more information, experiences, and a more adequate cognitive perspective and reasoning process to resolve the uncertainty. Participants will adapt their cognitive perspective and reasoning through understanding the perspective and reasoning of others to derive a new or reorganized conclusion. This process may be repeated several times before a decision is reached. The active search for additional information on the alternatives is also promoted, along with greater mastery and retention of information and a more accurate understanding of opposing viewpoints (perspective taking). Of the many positive outcomes of the use of controversy, the effect on higher level cognitive reasoning and processing is especially important in engineering decision making. Research has been done on expert-novice difference in medical diagnoses, physics problem solving, and geological exploration. It shows that preparation for verbal interaction and the actual verbal interaction with peers with differing view-points promotes the development of expertise. Constructive Controversy Conditions Some controversies among decision makers concerning their preferred solutions to a problem can be beneficial. But sometimes they are not. As with all types of conflict, the potential for either constructive or destructive outcomes is present. Whether the consequences are positive or negative depends on the controversy and the way it is managed. The conditions and procedures of controversy management that determine the outcome include: the goal structure within which the controversy occurs; the degree of heterogeneity of decision makers; the amount of relevant information distributed among decision makers; the ability of decision makers to disagree with each other without creating defensiveness; and the perspectivetaking skills of the decision makers. Goal structure: Two possible contexts for controversy are cooperative and competitive. A

Jan 3, 1985

The objective of this paper is, firstly, to summarize several field developments utilizing the art of hydraulic fracturing as it has been extended into various mining applications. Secondly, to summarize the understanding of the hydraulic fracturing processes; and lastly to discuss researchable areas and possible future applications. Hydraulic fracturing was developed as a method of stimulating production of oil from oil producing formations. The primary paper by Clark (1) in 1949, describes the process of placing a hydrostatic pressure of sufficient strength on the producing formation of an oil well that the rock apparently cracked, and then, on allowing the well to flow back, a higher rate of recovery of oil was enjoyed. The interpretation of the process mechanism was that the formation rock was cracked to a considerable distance from the well bore, increasing the drainage area; thus, the productivity of the well was measurably improved. Figure 1 is illustrative of this process. This development was of major significance to the oil producing community and considerable research and development ensued. Improvements in method, engineering development of equipment, and research to ascertain the optimum application of fracturing practice led to a highly sophisticated, but specialized technology. The Production Research Division, Continental Oil Company, vigorously pursued research in this area in the 1950's with a resulting number of process improve¬ments. The research group, published a significant number of technical papers on these various researches. One of the developments was the process aimed at controlled orientation of the fractures, either in the vertical (2) or horizontal (3) orientation.

Jan 1, 1969

By John J. Mulligan

Coal is found in every major geographic region throughout Alaska and in two offshore areas. Since about 1852 over 100 small mines have opened and closed. Last years production was almost entirely from one mine in central Alaska. Clearly the utilization of Alaska's abundant coal resources presents political, economic and technical problems that are far from solution. Location and Physical Features Figure one illustrates the geographical and geological similarity between Alaska and western United States. The Arctic region of Alaska generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The Central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of western United States. The Southcentral and Southeastern regions has a similar resemblance to the Sierra Nevadas and the west coast of the United States.

Jan 1, 1982

By W. M. Aubrey

Cobbing, as used in this; paper, refers to coarse dry magnetics separation. It is applicable when, by its practice, plant cost can be reduced or the value of its products increased by the removal of a barren or lean reject or a high grade final product. This paper attempts to describe cobbing as it is now being practiced, and also the problems that are of concern to the operator and design engineer. In preparation, 16 plants were contacted, all of which were very cooperative with their time and data.

Jan 1, 1958

By John S. Owens

The National Steel Pellet Project and the Butler Taconite Project are operated by The Hanna Mining Company in the vicinity of the towns of Keewatin and Nashwauk, on the western Mesabi Range. Production began in 1967, after seven years of exploratory and development diamond drilling and reconnaissance magnetic surveys, Previously, direct shipping hematitegoethite ores and gravity concentrates had been produced in the area from numerous open pits and several underground mines since the start of the century. Total shipments of these oxidized ores amounted to more than 200 million tons, but at the present time such reserves are nearly exhausted, and there are no mining operations in the Keewatin-Nashwauk area except at the two taconite projects. The locations of all of the present taconite operations on the Mesabi Range are shown in Figure 1, extending for a distance of about seventy miles from the Butler plant to the Dunka River area. The Butler and National plants have a combined rated capacity of 4.4 million tons of pellets. Their reserves cover a combined strike length of about eight miles on the Biwabik iron formation. All of the intervals between present taconite operations on the Mesabi are potential sources of additional magnetic taconite; in particular, exploration and economic studies have been carried out by Jones and Laughlin Steel Corporation in the Biwabik area between Aurora and Virginia, and by Pickands Mather and Company in the Hibbing area. However, west of the Henna and Butler holdings, it appears unlikely that magnetic taconite exists in commerical quantities at economic depths due to extensive oxidation of magnetite to hematite.

Jan 1, 1968

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962

By F. W. Metzger

Coal quality control in mining and mine planning has always been important and has become even more essential in recent years due to environmental considerations. The primary consumers of the sub-bituminous coals found in the Powder River Basin of Wyoming are electric utilities that require low sulfur coals to meet government air quality regulations. Electric generating plants are designed to burn coal of a specific quality, and the supplier of that coal must be able to guarantee shipments within specified quality tolerances. Over the past several years, Exxon Coal USA and, more recently, The Carter Mining Company, a division of Exxon Coal USA have established an evaluation and development program to accurately define the geology and quality of their coal properties. This requires an adequate drill hole density so that detailed correlations of the coal seam and the lithologic sub-units, of the coal seam can be made. These units must be recognizable in the core and also on geophysical logs.

Jan 1, 1981

By William L. Hodgson

HOARDS was written to fill the needs of an active minerals explorer. It permits retrievals using a number of spatial functions as well as direct relational logic, and enables statistical analysis within the system. Specified for use by non-EDP oriented staff, HOARDS also offers functions to subset, transform points to polygons of influence, and to calculate polygon overlap, enabling ready and efficient conversion of databases containing point oriented sample data to area/volume mine planning format. Both the design and implementation to date, and proposed enhancements are discussed.

Jan 1, 1979

By R. Bruce Thorndycraft

Pinson Mining Company was formed to develop a gold orebody located in northern Nevada near Winnemucca. A feasibility study was undertaken in 1979 by a consortium of three Toronto-based mining companies and a Reno-based exploration company. The study indicated a viable project with gold priced above $225 per ounce. A project manager, and mine and mill superintendents, were hired in late 1979 to expedite the development of a 1000 ton per day mine-mill complex. Plant design engineering was contracted with Industrial Design Corporation in Salt Lake City. Three experienced plant metallurgists representing Pinson were stationed in Salt Lake to guide the work of Industrial Design. Among the many design criteria spelled out by Pinson, foremost were bringing the mill on line as quickly as possible at minimum capital cost. Fourteen months after the beginning of design engineering, the completed Pinson mill became operational. Total capital cost, including mine development, was $18 million. The Pinson project has proved to be far more than viable; the entire capital cost will be recovered within 18 months of the mill start-up.

Jan 1, 1982

By Arthur C. Pincomb, Alan R. Shapiro

A public awareness of and commitment to abate pollution of water, air, and soil continues to stimulate demand for industrial minerals and rocks capable of neutralizing strong and weak acids. The role of acid neutralizing agents is 1) to treat acidified water and soil until the desired pH is attained and 2) to remove acid-forming compounds from industrial processes to mitigate the formation of acidic discharges. Environmental applications for these agents include: acid rain mitigation, neutralization and prevention of acidic industrial process discharges, and treatment of acid mine drainage and coal refuse. Desulfurization of industrial flue gases involves removal of sulfate compounds capable of combining with hydrogen to form acids. Details of flue gas desulfurization are covered in the previous chapter on Flue Gas Desulfurization. Ideally, the neutralization of acids results in an upward adjustment of effluent pH 7, or neutrality. The final pH value for many acid treated wastes, especially industrial discharge streams, is commonly over neutralized to pH 8.5 to 9.5. The Clean Water Act sets the upper discharge limit at pH 9. ACID NEUTRALIZATION REAGENTS Acid neutralization is accomplished by adding alkali metal and alkaline earth metal compounds to acidic water or soil until the desired pH is attained. The commonly used alkali ions are calcium (Ca), magnesium (Mg), sodium (Na), and potassium (K). Sodium hydroxide, high calcium and dolomitic hydrate, high calcium and dolomitic lime (quicklime), high calcium and dolomitic limestone, soda ash, and magnesium oxide are the compounds most commonly applied to raise the pH of acidic waters or soils. Limestone and dolomitic limestone, which are calcium and magnesium carbonates, and their equivalent oxides and hydrates formed by calcination, are the industrial materials most commonly used in the manufacture of reagents for acid neutralization. Approximately 327 kt of high calcium and dolomitic lime were consumed for acid neutralization purposes in 1988. Magnesite and brucite are industrial minerals that compete with dolomitic limestone for the magnesium-oxide market. Production of caustic calcined magnesia for neutralization purposes exceeded 6 kt in 1990. Soda ash is an industrial mineral gaining increased acceptance in the neutralization of acid waste discharges. Approximately 182 kt of soda ash were consumed in 1990 for acid waste treatment or acid prevention by flue gas desulfurization. Other mineral products either consumed in minor quantities or receiving attention as future neutralizing agents include zeolite and hectorite. In some cases, waste products have been found to be suitable and cost effective for neutralization of acids. Common wastes gaining acceptance include basic slag, phosphate mining refuse, cement kiln dust, fly ash, and mine tailings.

Jan 1, 1994

By M. R. Bowie, J. M. Barker, J. S. Hingtgen

Techniques of testing perlite require a combination of art and science. The modifications made to the perlite Corp. vertical laboratory furnace include addition of instrumentation, flowmeters, vibrators, automatic feeders, and regulators. The basic testing sequence consists of expanded density, furnace yield, compacted density, percent sinkers, and compaction resistance. These tests are modified versions of those specified by the Perlite Institute. This sequence is designed as a preliminary evaluation of a material's suitability for horticultural-aggregate end uses rather than a detailed measure of filtration capability.

Jan 1, 1988

By Gregory E. Klosterman

American Aggregates Corporation is one of the leading producers of mineral aggregates in the nation. Production is from deposits of glacial sand and gravel and limestone and dolomite bedrock. Annual production from 33 plants is 25,000,000 tons. Land consumption is at the rate of 300 to 400 acres annually. This annual rate of consumption presents a continuing challenge to the exploration and mining personnel to meet the requirements of reserve replacement, mining and land rehabilitation.

Jan 1, 1974

By F. Ames Smith

Offshore oil and gas production operations have moved from water depths of about 50 feet in 1948 to the present record depth of 340 feet. Although mobile drilling rigs are widely used for exploratory drilling, most development drilling and production operations have been conducted above water from the decks of fixed, bottom-founded platforms. Increasing water depths have caused problems associated with design and construction of these platforms and with laying of pipelines, but not so much with other activities. After a platform is installed, drilling, production, and maintenance operations are similar to those onshore and are relatively unaffected by water depth. Events of 1968 indicate that offshore production may soon extend into much deeper water. These events include leasing of Santa Barbara Channel acreage in water depths over 1500 feet, and the successful drilling of a wildcat well in 1300 feet. Designs have been developed for platforms suitable for installation in water over 600 feet deep, and studies suggest they may be used in some areas to water depths of 800 to 1000 feet. Buoyant towers can probably support above-surface platforms in water 1000 feet and deeper. Although the cost of either of these platforms will be high, once installed they will permit relatively low-cost development drilling and production operations compared with estimates for subsea production systems. In some cases, savings in development drilling costs alone could pay out the platform investment.

Jan 1, 1969

By Stanislaw Siewierski

One of the major problems in the exploitation of deep copper ore deposits in the Legnicko-Glogowski Copper Field is ground control and, in particular, roof control of the headings. The depth of copper deposits ranges from 600 to 1200 m. The parameters of ore-bearing rocks and the surrounding rocks show considerable variance of strength properties along the mining thickness (Fig. 1). The roof of the openings exploitation headings consists of dolomite-calciferous rocks. The roof strata consist of layers, the thickness of which vary from several centimeters to 0.6 m (sometimes to 1.0 m). These strata differ in strength and are characterized by igneous and sedimentary discontinuities. On the basis of studies in structure, properties and geological mining conditions of the roof strata in Polish copper mines, the method of roof classification has been developed. (1) This method uses the stability index "L" of the roof, calculated from [ ] The value of "t" ranges from 0, l to 0,8. Based on the value of "L", four classes of the roof (Table 1) corresponding to different degrees of fall hazard have been developed. The mining of copper ore deposit is carried out by a single lift room-and-pillar mining system or a two-stage room-and-pillar system with roof caving. (3, 4). The single lift room-and-pillar mining system is most often used. It consists in working of the deposit of 2.5 to 4.5 m mining thickness, 150-350 m long mining line, consisting of parallel room faces 6 m wide with pillars 5.7 or 16 m wide. As the mining line advances, cross-cuts joining individual rooms are made, thus forming support pillars 3x5, 7x7, 5x16, and 7x16 m (Fig. 2). The two-stage system (Fig. 3) mines the deposit with rooms 6 m wide into blocks 25 x 35 x 25 x 45 m. During the second step these pillars are worked with rooms and cross-cuts into pillars about 3 x 4 to 4 x 5 m (retreat mining). The pillars are crushed just before the fall of the roof. The maximum opening of workings in the two-step system is about 10 m, i.e. one belt entry and one row of bearing pillars. In single lift room-and-pillar systems it is about 35 m., i.e. three belt entries and three rows of bearing pillars. The support of the headings consists of expansion bolts 1.6-1.8 m installed in a bolting pattern 1.1 x 1.5 m. In both systems the fall step is about 10 m, i.e. the width of a belt and a bearing pillar. The Indications of Rock Mass Pressure Individual Dog Heading Individual dog headings are set wide apart from each other in the unmined ore deposit area where there is no interaction of headings. The indication of rock mass pressure are, in such cases, limited to the deformations and damage of side walls. Radiometric studies of rock mass loosening showed that the maximum range of lifts in side-walls immediately after web was 2 m (4,5). In the course of time the cracked side rocks fall off, thus widening the heading. The morphology of side-walls is influenced by the location of the heading in relation to clump layer/tarry. This layer is characterized by a weak strength and "lubricating" properties. The location of the heading in

Jan 1, 1982

By Werner T. Meyer

Technical modification of traditional zinc- and lead-based products is moving the metals into diversification is particularly apparent in two areas. The evolution of diverse types of heavy-duty vehicles that employ lead acid batteries. and The development of Galfan™ -- a zinc / 5% aluminum/mischmetal coating alloy designed to provided zinc-coated anti-corrosion protection in applications that are not well suited to traditional galvanizing. Because any product breakthrough must be accompanied by advancement and customer oriented thinking at every step in the chain of production and distribution, a concerted effort is required for market evolution to live up to its potential. As such, all those involved in the metals industries should not only track the progress made by technical and marketing innovations, they must participate as much as possible in their development and promotion.

Jan 1, 1986

By J. Appleby

This paper reviews earlier in-plant testing at the Sidbec-Normines pelletizing plant at Port Cartier, Quebec, Canada. It describes the result of the more prolonged use of coke breeze during recent months and in addition, the effects of varying dolomite and coke additives upon the metallurgical properties of the pellet production have been studied. Mention is also made of some brief test work carried out to use peat moss as a carbonaceous additive to the pelletizing process and in particular the plans for future work in this respect. Earlier laboratory pot-grate test work had indicated that a production rate increase of between fifteen and twenty percent was a practical possibility, or alternatively that the plant could be run at design rating with significantly lower energy consumption. These energy reductions were of the order of ten to fifteen percent for fuel and main process fan power respectively. The physical and metallurgical pellet properties for both blast furnace and direct reduction furnace use were little affected by the production rate increases, and were actually somewhat improved when practicing maximum energy conservations. Pellet properties could be further improved by not extracting the maximum energy economy. Two phases of carefully controlled in-plant testing were run to assess the effect of energy conservation under plant conditions. These two phases of testing confirmed that an overall fuel saving of approximately fifteen percent could be realized, with a reduction in the Bunker C oil consumption of about forty-five percent, and a reduction in main process fan power of approximately ten to fifteen percent. The present scope of work is aimed at establishing the use of varying levels of coke addition up to about one percent under normal plant operating conditions.

Jan 1, 1980