Search Documents

By J. F. T. Agapito

Energy West Mining operates the Deer Creek and Cottonwood/Trail Mountain coal mines in the Wasatch Plateau about 40 km (25 miles) southwest of Price, UT. The Deer Creek Mine extracts the Upper Blind Canyon seam and the Cottonwood/Trail Mountain Mine extracts the Hiawatha seam 12 to 36 m (40 to 120 ft) below. Both seams average about 2.8 m (9 ft) in thickness. Cover depths exceed 550 m (1,800 ft) in a large portion of the unmined reserve. Stability problems at Deer Creek are mostly due to coal bursts caused by high stresses associated with deep cover and sandstone channels. Most of the bursts have occurred in gate pillars and, to a lesser extent, at the longwall face and during development. The introduction of a two-entry gateroad system with 9-m- (30-ft-) wide yield pillars has been a major factor in controlling and minimizing gate pillar [ ] bursts (Agapito et al., 1988). However, some bursting began to occur in the 9-m- (30-ft-) wide pillars as cover depths reached 550 to 610 m (1,800 to 2,000 ft). This was due to more rapid and higher abutment loading in areas with very strong roof and stiff floor.

Jan 1, 1997

By John A. Dearinger, Fred D. Wright, Robert C. Howell

INTRODUCTION The rock mechanics study of the shortwall mining system at Beth-Elkhorn corporation's Hendrix No. 22 Mine is being conducted under contract with the U.S. Bureau of Mines. The objective of the study is to obtain data on surface subsidence over a portion of the mined area, strata subsidence in the mined area, and underground stress changes and displacements in and near natural support elements of the mining system. This study is currently in progress, and only a portion of the results are being presented at this time. The Hendrix No. 22 Mine is located in the moderately rough mountainous terrain of Letcher County in eastern Kentucky. The nearest mine workings to the shortwall area are approximately 1,900 feet distant. The depth of cover over the mined shortwall area varies from 770 feet at Panel 1 to 170 feet at Panel 5 (Figure 1). The strata in the shortwall area is summarized in the three core logs shown in Figure 2. Hole no. 2 is located in approximately the center of the mined shortwall area (Panel 3, Line C, Figure 1). The coal seam in the shortwall area is approximately 4 feet thick and horizontal, although one major ‘roll’ intersects all panels.

Jan 1, 1977

By P. Soros

Rich iron ore deposits were discovered during the 1960's in the mountain range of Serra dos Carajas, State of Para, Brazil, near the headwaters of the Tocantins River some 400 miles southwest from the state capital of Belem. (See Fig. 1 and 2). The key to the successful exploitation of this deposit was the development of an efficient an economical transportation system. The rugged terrain, and the dense tropical vegetation of the Amazonian jungle and the irregular coastline with its high tidal range presented severe obstacles to the planning and building of such system. Starting in 1972 extensive surveys and studies were carried out by Soros Associates on behalf of CVRD to determine the optimum way of transporting the ore from the mine site to the markets, most of which are located overseas. Overland transportation to the coast, loading into seagoing vessels and the ocean voyage to the ports of destination was treated as an integrated system in these studies.

Jan 1, 1986

By C. R. Zegarra

Extraction of manganese, gold, and silver from a low-grade manganiferous-silver ore was investigated by thiourea leaching followed by standard cyanidation. The levels of reagent concentrations in this investigation were 0.0 -1.0 M thiourea and 0.0 -1.0 M sulfuric acid. Temperature and agitation speed were maintained at Z5 °c and 300 rpm, respectively. The dissolution of gold, and silver was shown to be dependent mainly on sulfuric acid and thiourea concentrations. In general, 50.0 % Ag, 98.0 % Au, and 75 % Mn were recovered from a Mn-Ag ore by thiourea leaching. Overall silver extraction of 98.0 % was obtained by cyanidation after thiourea leaching. Thiourea leaching of sodium bisulfite leach residues was also studied, and the total extraction of gold and silver were 97 % and 40 %, respectively. Finally, a two-stage thiourea leach was also investigated.

Jan 1, 1988

By S. K. Sharma

The Bureau of Mines' rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992

Canada is a major producer of chrysotile asbestos. In fact, Canada accounts for approximately one third of the world chrysotile asbestos production. Deposits are mined and the fiber processed in Québec, in British Columbia on the West Coast and in Newfoundland in the Atlantic region. Foremost among the Canadian provinces is obviously Québec. Some 85% of Canadian deliveries come from mines located in the Eastern Townships, a region which lies along the southshore of the St. Lawrence River, between Montreal and Québec City. At the heart of this vast territory, five (5) mining towns make up what is called the Québec asbestos region. Total capacity of the five (5) mining producers of Québec is about 1 366 000 tonnes.

Jan 1, 1981

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By S. Guo

In this paper, a model for the resin anchor bolt system is developed in which the smooth bar is modeled by using one-dimensional truss elements and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined together and then incorporated into the' existing computer code ROOFBOLT. After this development, all of the components in the resin anchor bolt system including smooth bar, bearing plate and resin annulus can be correctly modeled.

Jan 1, 1995

Engineering programs usually do not provide sufficient opportunities for students to develop written communication skills. The responsibility for developing those skills is frequently delegated to the humanities faculty, who in a single technical writing course are supposed to transform engineering students into proficient communicators. A general template which was developed for report writing in our senior level capstone design courses is discussed. Students have improved their writing skills by using the template. The writing assignments have provided the students the opportunity to write and revise more technical reports that communicate their design.

Jan 1, 1995

By M. Misra

A sample of thorium-contaminated soil from Kirtland Air Force Base (AFB) was subjected to froth flotation for removing thorium contaminants. A series of flotation tests were conducted to screen and evaluate the reagents. Among the collectors used, sodium oleate exhibited to show the promising results. Preliminary tests showed that a concentrate having activity as high as 5300 pCi/g can be obtained from the contaminated feed soil having activity 800 pCi/g. The volume reduction obtained was 89% and the activity recovery in the concentrate was 68%. The paper discusses the physico-chemical characterization data and the potential physical separation decontamination schemes for the thorium contaminated soils.

Jan 1, 1996

Approximately forty years ago, the military services began a realistic investigation of the problems involved with the replacement of high pressure gaseous systems with liquid oxygen systems. The program was temporarily discontinued because of numerous State-of-the-Art problems. Ten years later, interest in the liquid oxygen breathing concept was revived. Initial testing of this concept was completed in 1946. The ensuing years have seen the general acceptance of many cryogenic breathing systems for airborne applications. The inherent features of weight savings (approximately 70%) and space savings (approximately 80%) make it very desirable for high performance military aircraft. A typical aircraft system consists of a storage container with appropriate integrated control valving (the liquid oxygen converter), a heat exchanger, breathing regulator, and oxygen mask. Normally the liquid converter is located in the aircraft wheel well for easy access by ground crew personnel and the breathing regulator is mounted in the cockpit where the pilot can connect his oxygen mask. An aircraft system such as this will provide the pilot with eight hours of breathing oxygen after a 24 hour standby period. Early in 1960, the National Aeronautics and Space Administration sought a means of providing a cooling system for their personnel involved in fueling the rockets used in the space program. While fueling rockets N.A,S.A, personnel wore a completely enclosed butyl rubber suit and were susceptible to heat prostration. Using the concept of an aircraft system, Aro redesigned the container, heat

Jan 1, 1971

By Russell W. Hunt

The cave man of ages past took his wife-and family from the cave pointing to a fire he had built and beating on his breast said, "Look what I have done". Today man is taking his family back to a cave saying, "Come enter in because of what I have done". At the close of World War II Germany said if they had gone underground one year earlier with more of their operations, the war could have lasted four years longer with perhaps much of Britain devastated. The protection of the home front no longer rests with the soldier in actual combat. The battle will be won at home with the most careful kind of protection against missiles. After Nagasaki-Hiroshima Sir Winston Churchill said in substance "Up to now the Almighty has mercifully withheld from man the knowledge of these terrible weapons of destruction."

Jan 1, 1959

By N. Standish

Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage -"the bottom line evaluator." Correct.

Jan 1, 1990

By D. Sinha

Mine investment decisions involve both objective and subjective criteria. The subjective criteria are efficiently decided by interaction with company experts. The Expert System approach can incorporate knowledge of experts and interact with conventional computer programs on mine evaluation. Artificial intelligence offers considerable opportunities in comprehensive mine investment decision making process.

Jan 1, 1998

By J. Driscoll

After 30 years of success, Newmont Gold Company has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East Decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East underground at the rate of 700 t/d (770 stpd) for an annual production of over 100,000 ounces. Over 70 underground miners enjoy the estimated 6-year mine life at Carlin East. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By V. N. Kolesnikov

The gold-silver deposits of the northern Primorye region are located in the eastern part of the East Sikhote-Alin volcanic belt, where the belt overlaps the Kema island-arc terrain of the Aptian-Albian age. There have been four deposits and numerous mineralization points found in the NE-trending Kema metallogenic belt that is about 1000 km long and 100 km wide. The known mineralization is of epithermal type, controlled by faults, and concentrated in quartz, quartz-fluorite-adularia, and, less commonly, sulfide-quartz vein systems hosted by the Upper Cretaceous-Lower Tertiary volcanic rocks. The vein systems extend for hundreds meters along strike, varying from tens centimeters to 50-60 meters in width. They are surrounded by wide zones of low-temperature hydrothermal alteration containing some gold-silver mineralization for which the commercial value was not studied during the early exploration. The ore bodies contain from 1 to 50-80 ppm of Au and from 1 to 1000 ppm of Ag. Gold is native, associated with quartz, and represented by particles from tens of microns to 1 mm in size. Silver occurs in native form as a constituent of argentite, pyrargyrite, stephanite, and other sulfosalts. The test work carried out for three vein systems 20 years ago showed that gold might be easily and almost completely recovered from the ore by cyanide treatment. The paper describes the geology and mineralogy of the deposits, Salut and Primorskoye, that are the most studied properties of the Kema belt. It also presents the data available on disseminated gold-silver mineralization in stockworks, altered explosive breccias, and wide zones of low-temperature hydrothermal alteration. This mineralization should be explored for possible exploitation as large open-pit, heap-leach deposits.

Jan 1, 1998

By D. Marsh

The feasibility study for the Grasberg Block Cave mine, finalized in May 2008, indicated a production capacity of 160,000 tonnes per day. A rail haulage system was an integral part of the mine design. This paper describes the simulation process used in optimizing the design and discusses the key factors and variables that impact the capacity of the system. The final recommendations for the haulage level layout and associated equipment are also included.

Jan 1, 2010

By Peter Hall

The need for large volume covered storage has increased drastically in the last ten years. Increased world demand for such products as thermal coal, potash, metallic concentrates, etc., availability of land for large open storage and environmental issues have brought about this need. This paper discusses briefly demand, environment, types of covered storage and the Alternative Storage System "Eurosilo", a proven system for storage of dry bulk mateials in units up to 100,000 m3.

Jan 1, 1982

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986

By W. A. Yuill

A process has been developed for increasing the grade of chalcopyrite concentrates from about 25 percent copper to about 60 percent copper. The concentrates are treated with two steps of autoclaving and then by flotation. Because of the lower associated weight, copper in the concentrates could be shipped and smelted at less cost than untreated concentrates. Use of the process can also increase overall yield from an orebody if a lower grade concentrate is sent to enrichment than would be sent to a smelter. Potential applications of the process would be for treating concentrates that must be transported a long distance for smelting or for treating concentrates so as to increase the capacity of a smelter.

Jan 1, 1984