Search Documents

By Michael F. Werneke

While the use of synthetic polymers for solid/liquid separation is not raw technology (1)(its history goes back to the mid 1950's), its importance has increased dramatically over the past decade. This can be attributed to two major factors. The first of these was a change to mechanized mining (strip mining and continuous underground miners) which resulted in a lower quality (higher reject) preparation plant feed, as well as a higher percentage of smaller size particles in the feed. The second factor has been the greater restrictions imposed by governmental agencies on effluent discharge and solids impoundment, requiring pre-treatment of recirculating water before reuse and treatment of refuse before disposal. Today, synthetic polymers find utility in almost all applications requiring separation of solids from aqueous suspension, including "in-process" as well as waste treatment applications. In spite of the fact that there are over several hundred commercially different flocculants available in the marketplace (2), there are a limited number of chemically different materials available which are useful from a cost/performance standpoint. The potential reasons for using flocculants in a coal preparation plant are summarized in TABLE 1.

Jan 1, 1979

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By S. Acar

The results obtained for the selective flocculation or flotation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is disscussed. Dissolved Fe, Cu and Ni species are found to affect the properties of chalcopyrite, pentlandite, millerite, pyrrhotite and covellite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation and complexation of species, etc.

Jan 1, 1985

By A. A. Terchick

In 1970 U. S. Steel acquired the physical assets of mine, mine property, and preparation plant of the Crystal Block Coal Company near Thacker, Mingo County, West Virginia. The facility, identified as U. S. Steel Mine No. 20, is administered and operated as a production unit of U. S. Steel Gary District, Gary, West Virginia. Mining operations of the No. 20 mine are conducted in the high-volatile Alma seam. The preparation plant, which originally had a capacity of about 150 tons per hour (tph) of raw-coal feed, had process circuitry consisting of a Daniels heavy-media vessel for cleaning the plus-1/4-inch raw coal, a McNally-Pittsburg feldspar jig for cleaning the 1/4 inch by 28 mesh, and Daniels flotation cells for treating the 28 mesh by 0. No water-classification system existed. Refuse tailings from the plant were pumped to several surface lagoons which were decanted to the stream. The settled solids were removed and trucked to the coarse-refuse disposal area. Water make-up requirements were supplied by a small mine-water surface reservoir and augmented with stream water. Expansion of production from the property required an increase in preparation-plant raw-coal-feed rate capacity from

Jan 1, 1974

By S. J. Jung

In recent years, the use of shotcrete, a practice familiar to the mining industry, has been on the increase. This research has come about because of the recognized need for a safe, easy way to line small diameter bored raises (less then 150cm). Up until now, an operator has gone down the raise and applied the concrete lining manually, using the shotcrete method of application. With an automated system, there would be no man positioned in the bore itself. All control functions could be commanded from a central location. Shotcreting in the confined space of a small diameter bored raise presents problems that can be overcome by the application of shotcrete using a remote system.

Jan 1, 1994

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By Clement K. Chase

Although flotation is the generally accepted process employed to recover gold and silver as well as copper, lead, and zinc from primary sulfide ores, the metallurgical requirements for the treatment of massive sulfide ore deposits differ markedly in many respects from those employed for the more common disseminated porphyry deposits. In Arizona, some properties classified as other then massive sulfide deposits because of mining and geological characteristics have produced mill-feeds similar to those from massive deposits. Several such occurrences are noted. The process requirements for massive sulfide deposits and unique mill-design implications are discussed in the perspective of world-wide economic considerations and the individual regional metallurgical and economic constraints in the United States.

Jan 1, 1986

By H. K. Lin

During slow-cooling crystallization of iron-making blast furnace slags, most rare-earth elements in the feed recrystallize as cerite-calcium while scandium and europium concentrate in a sheet-like "mineral". The mineralogy of this "mineral" is studied with one of the objectives being the extraction of the "mineral" from the slag for recovery of Sc and Eu. This "mineral" has been identified as one of the mica group minerals and can be named as rare-earth-bearing barium fluorophlogopite. The mineralogical characteristics of this "mineral" are investigated and discussed. This "mineral" can be effectively recovered from the slag by flotation with dodecylammonium acetate or a combination of dodecylammonium acetate and sodium oleate as a collector.

Jan 1, 1996

By Jon C. Yingling

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will be intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder throughflow to avoid production bottlenecks.

Jan 1, 1992

By R. W. Smith

A number of investigators have studied the electrokinetic potential (?) of kaolinite as a function of pH. (1,2,3,4,5) These investigators all agree that the ? is negative except at quite acid pH values. The actual shapes of the curves reported by the several authors vary considerably. In spite of the general negative character of kaolinite the mineral has a rather high anion exchange capacity. (6,7,8) The cation exchange capacity is the lowest for the clay minerals. (6) It has been shown that anionic surfactants adsorb readily onto the mineral even up to neutrality, often in quantities exceeding the reported anion exchange capacity. (7,8) At least part of the anionic adsorption should be onto positive edge sites thought to exist on the mineral. (9,10) In the present study ? of kaolinite was measured as a function of pH using both the streaming potential (sp) and microelectrophoresis (m.e.p.) methods. In addition ? was measured at various pH values as functions of sodium dodecyl sulfate (SDS) and trimethyldodecylammonium chloride (TMDAC) concentrations. In some experiments decyl alcohol (DA) was added.

Jan 1, 1968

By T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of backmixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically made very tall, on the order of 30-40 feet, in order to limit the effects of backmixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug-flow. In this work, horizontal baffles were shown to improve the performance of a 6-foot tall laboratory-scale flotation column treating a difficult-to-clean, heavily oxidized coal. Tests with variation in the position of the baffles showed that for the greatest benefit, baffles are needed both above and below the feed inlet. Tracer tests with a fluorescent dye water tracer showed that the addition of the baffles reduced the amount of feed water entrained into the froth at any given coal recovery.

Jan 1, 1994

By Thomas F. Torries

It does not take sophisticated economic analysis to determine the current status of nickel production and demand (Figure 1). One only needs a quick glance at the balance sheets of the major nickel producers to learn that prices are down and profits are supressed to the point where they are major losses. Operations have been closed, and those remaining in production have reduced output. What Is now of interest Is, when will the nickel market improve and to what degree? The purpose of this paper is to attempt to answer these questions. This will be done by the normal method of projecting nickel demand, chosing a production scenario, and analyzing the results.

Jan 1, 1982

By Henry H. Rubin

Rubber and its contributions to the economic solutions of environmental problems in the minerals industry. The intelligent applications of "Rubber" to systems of noise abatement, vibration isolation, dust containment, weak and corrosion resistance has proven economically beneficial. Intelligent application requires a thorough understanding of the nature of the material, knowledge of the process wherein it is going to be applied, and consideration of the environmental conditions in which it will serve, for these determine the proper amount, type, compound and configuration for an economically successful application.

Jan 1, 1979

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

Due to the relatively remote location of the St. Anthony Mine, the high cost of transportation and milling, plus the low grade nature of the deposit, the United Nuclear Corporation began investigating methods of mechanical upgrading approximately eighteen moths ago. This investigation culminated in the installation of Model 17 and Model 18 ore sorting machines. The machines are marketed in the United States and Canada by Ore Sorters of Canada (Ltd.). The installation of this advanced technology will enable United Nuclear Corporation to fully realize the residual potential of St. Anthony.

Jan 1, 1979

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By Richard Gallagher, Russell K. McFarland

INTRODUCTION The Southern California Rapid Transit District has commenced Preliminary Engineering for an 18 mile Metro Rail Project. This initial line will consist of approximate 36 miles of single track tunnel and 16 subsurface stations. The estimated cost of $1.2 Billion in 1978 dollars, places it in the category of a major public works project. During the planning phase of this project, particular attention was paid to the National Academy of Science Reports, "Better Contracting for Underground Construction" (1974), "Better Management of Major Underground Construction Projects" (1978), and "Management of Urban Construction Programs" (1980). The improved transportation service that this project will furnish the Los Angeles Metropolitan Area will result in significant benefits that will add immensely to the economic well being of the community-which is one of Webster's definitions of improved productivity. RAPID TRANSIT PROJECT BACKGROUND Rapid Transit studies have been going c in the. Las Angeles area since 1925. In 1969 and 1974, sales tax ballot issues were not adopted by the electorate of the county mainly because the pre-ponderous of County voters are outside the City of Los Angeles.

Jan 1, 1981

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By Aydin Shaterpour Mamaghani, Cemal Balci, Nuh Bilgin, Mucahit Namli, Hanifi Copur

"It is expected that more than 10 Billion USD will be spent in Istanbul in coming years on tunnel boring especially with EPB-TBMs. However, the geology of Istanbul is very complex. Geologic formations changing from Paleozoic to Cenozoic ages cause tremendous problems due to frequently changed rock formations and andesite and diabase dykes. This paper summarizes a universal model to predict the performance of EPB-TBMs which is created upon the data base collected from several projects. The model first is based on predicting field specific energy and power consumed of TBMs using geo-mechanical properties of the excavated material and TBM diameter. Later net production rate is calculated using field specific energy and power consumed by TBM. A methodology to predict machine utilization factor permits to calculate daily advance rates. The validity of the model is tested using the data obtained from two recent metro tunnel projects. 1. INTRODUCTION It is expected that in a near future a total length of 400 km will be excavated in Istanbul in a complex geology. Selecting proper tunneling equipment, organizing an effective operational management with the right tunneling crew will be a major concern for an efficient scheduling of the future projects necessitating to create a model to estimate daily advance rates. Several TBM performance prediction models with few on the prediction of machine utilization time were realized in the past. However, there is quite limited number of research studies on predicting the performance of EPB TBMs. Specially predicting daily advance rates in complex geology, in mixed face, in fractured rocks, in transition zones etc. are in big concern (Namli et al. 2013, 2014). The first experiences in Istanbul with a gripper type TBM was a nightmare, roof collapses caused big delays in tunnel excavation (Bilgin 1993). A typical example to EPB-TBM was Kadikoy-Kozyatagi tunnel, changing TBM from opened mode to closed mode with few modifications on the cutterhead resulted a tremendous increase in the daily advance rates (Bilgin et al. 2009). The data collected from several tunnelling projects served a basis to create a model to predict daily advance rates of EPB TBMs. Within the frame of a research program the validity of the model was tested in Uskudar-Umraniye–Cekmekoy-Sancaktepe metro project and very recently in Mecidiyekoy-Mahmutbey project."

Jan 1, 2016