Search Documents

By Jack A. Touseull

The Bureau of Mines has developed a simple stereographic method of analyzing the orientation of single and intersecting planes of weakness in vertical pillars of parallel symmetry. From this method, it can be determined if planes of weakness transect the full horizontal cross section of a pillar. A major finding resulting from this method was that intersecting planes of weakness can transect the full horizontal cross section of a pillar even though the individual planes do not. This paper provides step-by-step instructions for using this method.

Jan 1, 1977

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959

By John R. Benham

In 1987, at the request of the Bureau of Land Management~ the U.S. Bureau of Mines studied 7,600 and 3,000 acres, respectively, of the Slocum Creek (OR-003-075) and Upper Leslie Gulch (OR-003-074) Wilderness Study Areas in order to evaluate their mineral resources. They are located in Malheur County, OR, about 25 mi northwest of Jordan Valley. Both areas have an occurrence of stone (welded tuff) covering about 3,000 acres which is suitable for construction purposes including road metal, ballast, and road fill. However, similiar deposits are more accessible and closer to markets.

Jan 1, 1988

By James S. Browning

The Bureau of Mines conducted laboratory and small-scale continuous tests of kyanite ore from Georgia to determine the technical feasibility of recovering commercial-grade kyanite concentrates by flotation. The research indicated that combinations of sulfuric acid and petroleum sulfonate may be used effectively for flotation of kyanite from quartzite-kyanite ore. Over 87 percent of the kyanite was recovered in a concentrate analyzing 55.8 percent A1203 and 5.3 percent acid-soluble Fe203. Subsequent treatment of the flotation concentrate by high-intensity wet magnetic separation reduced the acid-soluble Fe203 to 0.8 percent and increased the alumina content to 57.6 percent, with a recovery of 82.7 percent of the total alumina in the ore.

Jan 1, 1970

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Black Butte RARE (I area during the summer of 1981. The study area encompasses 17,800 acres [27.8 sq mi (7,233 ha)] along the course of the Black Butte River, 13 mi (22 km) southeast of Covello, California. No mineral deposits were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese, chromium, and nickel. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 9, 1984

By J. M. Stuve

This Bureau of Mines investigation measured the low-temperature heat capacities of FeOC1(c) and FeC13(c) in the temperature ranges of 6 to 305 K and 4.6 to 300 K, respectively. The standard entropies (S°, 298.15 K) of FeOCl(c) and FeC13(c) were derived as 19.73±0.03 cal/deg-mole and 35.33±0.07 cal/deg-mole. A large lambda transition was observed in the heat capacity of FeC13(c) at 8.4 K. The standard enthalpy of formation (?H°f, 298.15 K) of FeOC1(c) was determined to be -98.23±0.22 kcal/mole by HC1 solution calorimetry. High-temperature enthalpy measurements (H-H298.15) of FeOC1(c) were determined to 700 K by precision drop calorimetry. Standard thermodynamic formation data and related functions were tabulated at various temperatures for FeOC1(c) and FeC13(c).

Jan 1, 1980

Minimize failures or inefficiency in the operation of in situ mining wells. Approach The proper design, construction and development of wells are important to any in situ leaching operation. To permit cost-effective production from an underground ore body by leaching it in place, many wells are normally installed. Construction and maintenance costs increase with the number of wells, and poor construction and maintenance procedures result in production losses and negative environmental impacts, To minimize these losses and impacts, the Bureau of Mines conducted an investigation to determine the optimum in situ well construction and operating procedures for the minerals industry. Factors considered during the investigation included drilling equipment and procedures; types of well casing and grouting; completion methods, e.g, screening or perforation; and system maintenance. The data collected were used to prepare a manual that offers guidelines

Jan 1, 1984

CESIUM metal production increased sharply in 1963. Domestic Production.--Cesium metal was produced by The Dow Chemical Co., Midland, Mich., MSA. Research Corp., Callery, Pa., and by Penn Rare Metals, Inc., Revere, Pa. American Potash & Chemical Corp., Trona, Calif., produced some combined cesium and rubidium. This company, Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., produced various cesium compounds. Complete production data on cesium and rubidium and their compounds were not available for publication. Consumption and Uses.-Substantially more pollucite was consumed to produce cesium metal and compounds in 1963 than in 1962 but the overall consumption of pollucite continued to be small.

Jan 1, 1964

By Thomas V. Falkie, R. Venkataramani

The purpose of this work was to Investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors - geometrical , geological, mechanical, or procedural - which affect the delivery rate, and to develop quantitative rate-descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily Influences the loading function The geometrical factors -the dimensions of the work area In relation to the dimensions of the mining machine -were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent Independent variables. It is expected that this work will be useful In operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Sep 1, 1972

By D. K. Ingram, G. L. Mowrey, T. R. Rehak

This paper summarizes fly rock and blast area security fatalities from 1989 to 1999 and examines the causative factors. Coal and nonmetal mining used about 43 billion pounds of explosives and blasting agents between1989 to 1999. A majority of this consumption was used at surface mines. Accident data indicates that fly rock and lack of blast area security were the primary causes of blasting related injuries in surface mining. Fatal injuries due to lack of blast area security were attributed to: failure to clear blast area; failure to follow instructions; inadequate guarding; inadequate blasting shelter; and unsafe location. Seven fatalities due to fly rock and lack of blast area security were reported in surface coal mines and six in nonmetal mines. Out of these, two fatalities (one each in coal and nonmetal mines) occurred outside the mine property. In the coal mining sector, two fatalities were attributed to fly rock, and five to lack of blast area security. In the nonmetal mining sector, three fatalities were attributed to fly rock, and three to lack of blast area security. Preventive measures include: ensuring that all personnel have evacuated the blast area during shot firing; using adequate blasting shelters for employees whose presence is required in the blast area; controlling and monitoring all entrances to the blast area; ensuring that the blast is properly designed, drilled, and loaded; and emphasizing education and training to enhance skill levels for implementation of engineering control techniques.

By C. W. Owings, F. E. Cash

"Transportation of explosives in mines is extremely hazardous, and where electric haulage is employed the danger is intensified. Insulated mine-car couplings have been adopted by at least five companies in Alabama and Pennsylvania - and undoubtedly in other States - to prevent an electric current passing from a mine locomotive to a car or between care joined by this coupling. The need for such protection is recognized in the report of an explosion.""Four hundred kegs of black blasting powder had been loaded into four mine cars at the railroad, to be hauled to the magazine, upgrade, by a trolley locomotive. On starting, the motorman put sand on the rail and a grounded circuit passed through the hitchings and so exploded the powder. No insulation was used between the locomotive and cars."" When used on man trips the insulated coupling further serves the purpose of guarding the men against shock. Four couplings are described so that a clearer understanding may be obtained of the details of construction.ConstructionThe general principles of construction are similar in all insulated couplings. The piece containing the hole for the coupling pin is made of steel and the steel parts are separated by an insulating material, such as fiber or wood. The coupling is either rigid or semirigid to prevent the bumpers of the mine cars from coming in contact and to keep the cars insulated from one another at all times."

Apr 1, 1928

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

By A. N. Styler

As part of its water-jet assisted rock cutting research, the Bureau of Mines has initiated a study into the mechanism of rock fragmentation by water-jet-assisted mechanical tools. The objective of this research is to increase coal extraction efficiency by seeking an improved understanding of the synergistic relationship between mechanical cutters and water jets, enabling the design of more effective cutterheads. Rock chips collected during laboratory traverse speed jet-assisted cutting tests were analyzed with respect to the size distribution of the chips and the forces measured during cutting. As the water-jet pressure was increased, the size distribution of the product became coarser with V-face type cutting tools producing less fine material than conical cutting tools. Fracture mechanics theory accounted for less than 10 pet of the energy consumed during fragmentation of the rock. The energy consumed by processes other than rock breakage decreased with the use of water jets and increasing advance rate.

Jan 1, 1987

By L. D. Tracy

"Introduction In the course of the investigations by the Bureau of Mines into the various causes of coal-mine explosions, the fact that several gas explosions had occurred during or very soon after a mine was being un-watered, attracted the attention of the Bureau's engineers. The apparent coincidence was so marked that there appears to be an extra hazard present, whenever water, which has been standing against the face of the coal for some time, is suddenly removed either by natural drainage or by mechanical means.Actual Occurrences Case 1. - A typical illustration of this hazard is shown in a gas explosion which occurred in a mine in Central Pennsylvania. Four main entries, 50 feet apart with an average grade of 6 per cent, had been driven with the dip of the coal, and from these mains 7 pairs of entries, at intervals of 800 feet, had been turned at such an angle that their grade was slightly rising. Prom these latter pairs of entries, rooms were turned practically at right angles.The main entries had been driven for 4,500 feet and at the face there was 400 feet of cover. As far as could be observed, the roof was of sandstone and the floor of clay.The coal bed being mined was the Lower Kittanning, which has a thickness of about 4 feet. A typical analysis of the coal in that section is as follows:"

Oct 1, 1924

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982

By Maria I. De Rosa

Table 55 and figure 19 show the number of fires and fire injuries for stone mills by state during 1990-2001. Table 55 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 118 fires occurred in 33 states. Seventy-six of the fires caused 82 injuries (including 8 fires and 6 injuries involving contractors). The yearly average was 9.8 fires and 6.8 injuries. The Ewhr value was 873 x 106 hr (In = 0.019), and the LWD value was 1,911. Missouri had the most fires (16 fires and 9 injuries), followed by Pennsylvania (15 fires and 14 injuries), Michigan (9 fires and 5 injuries), and Virginia (7 fires and 5 injuries). Of these states, Virginia had the highest injury risk rate value (In = 0.09 1). Table 56, partly illustrated in figure 20, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries decreased during most of the periods, with a sharp increase during the last period. The number of employees' working hours increased throughout the periods. The In values follow patterns similar to those shown by the injury values. Tables 57-63 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 21 shows the major variables related to fires for 1990-2001. Table 63 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing. the stage of measurement used in this chapter is what is normally termed ?mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989