Search Documents

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1992

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980

By Stephen D. Cramer

The Bureau of Mines conducted a series of in situ linear polarization measurements in high-temperature, high-pressure hypersaline geothermal brines at the Bureau of Mines Geothermal Test Facility in the Imperial Valley of California. The measurements represented an evaluation of the linear polarization technique for obtaining instantaneous corrosion rates of materials of construction in flowing hypersaline hydrothermal fluids that rapidly form scales on exposed surfaces. A special method was devised for use with the linear polarization technique that resulted in obtaining corrosion rates for 1020 carbon steel, 316 and 430 stainless steel, titanium, various nickel-based alloys, and aluminum 6061 under strong scale-forming conditions. The measurements also provided information on scale-deposition rates in various geothermal environments. Exploratory in situ potentiostatic polarization measurements were made in the flowing brines to qualitatively determine scale-deposition effects on the electrochemical measurements.

Jan 1, 1978

By Benjamin W. Haynes

The Bureau of Mines conducted research to devise technology for increasing the Nation's mineral supply by recovering valuable constituents from currently discarded waste materials. Municipal solid waste (MSW), presently a major disposal problem, represents a significant source of metals, glass, and a combustible fraction that can be used to supplement coal in generating heat and electricity. As part of the total metallurgical system to treat MSW, this study evaluates the combustible fraction of MSW to characterize the various combustible components and to identify the principal sources of elements that eventually may be objectionable from corrosive or environmental considerations. Several possible sources for cadmium, chromium, cobalt, copper, lead, nickel, and zinc have been tentatively identified. These sources are pigments, inks, paper stock, and additives to plastics. A correlation between industry consumption values and measured concentrations in MSW was found for several elements.

Jan 1, 1978

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By John C. Edwards

Chapman-Jouguet detonation calculations were carried out for pentaerythri-tol tetranitrate (PETN), TNT, and ammonium nitrate-fuel oil (AN-FO) explosives using the compressibility form of an equation of state of hard spheres based upon Percus-Yevick (PY) theory, and a chemical equilibrium detonation code called TIGER. Similar calculations were also carried out with the Becker-Kistiakowsky-Wilson (BKW) equation of state. For PETN, the BKW equation gives somewhat better agreement with experimental values of detonation velocity and pressure. However, in terms of experimental temperatures and concentrations of the minor product species (NO), the predictions of the PY equation are shown to be more satisfactory. Similar comparisons of experimental and theoretical results for TNT and AN-FO indicate that the PY equation has general utility in predicting the detonation properties of condensed explosives at moderate loading densities (Po < 1.3 g/cm3).

Jan 1, 1974

By Alan R. Buehler

A mineral survey of the 20,792-acre Sand Butte WSA (Wilderness study Area), ID-57-8, was conducted by U.S. Bureau of Mines personnel in 1985, at the request of the Bureau of Land Management. The WSA is in Lincoln County, south-central Idaho, about 15 miles south-southeast of Carey. There are no mines, prospects, or claims within the WSA. Basaltic lava is the only rock type exposed within the WSA. The only mineral resource is a few tons of a platy variety of lava (slab pahoehoe) which is suitable for use as decorative stone. Similar slab pahoehoe, produced from other lava fields in southern Idaho, retails for approximately $125/ton. The deposit in the WSA is too small to be mined commercially but may have value to consumers who gather their own decorative stone. INTRODUCTION A mineral survey of the Sand Butte WSA (Wilderness Study Area) 1/ was conducted in June 1985 by the USBM (U.S. Bureau of Mines) and the USGS (U.S. Geological Survey) at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will he used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data to the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Roy Greenfield

During the detection phase, several procedures can be used to improve the signal-to-noise ratio (SIN) . • Subarrays of up to 10 seismometers should be used. The apparent failure to obtain improvement in SIN in the Westinghouse subarrav work is probably due to excessive noise in the electronics. The spacings needed for sensors in the subarray must still be established. • The sensors should be buried. Even burial to a few feet will probably give appreciable reduction of noise. A deeper burial will probably further reduce the noise; and, if the seismometers can be put below the weathered layer, the signal level will probably be increased. The reduction in noise by burial will be especially effective during high noise periods due to wind or rain. • Before attempting detection, the waveforms should be bandpass filtered. The bandpass should go from 25 Hz to an upper frequency of 100 to 200 Hz. Further measurements with a low noise system must be done before the signal-to-noise ratio can be determined for the 100 to 200 Hz range. Any narrow band noise should be removed by notch filters. • If noise levels differ among seismometers of a subarray, weights inversely proportional to the noise power should be applied to the seismometers. • Automatic methods of screening data for possible signal arrivals should be developed, but the final determination that the signal on a subarray output appears to be from a miner should be made by an analyst. Detection of "signal" on several subarrays should be required for positive identification. In the location phase, after detection: • If repeated signals are received, they should be coherently added (stacked) to give as good a SIN as possible for use in determining signal arrival times, to be used in location computations. The miner should, if possible, repeat the signal 25 to 50 times.

Jan 1, 1974

By Roy H. Grau, John C. LaScola

This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau&apos;s coalbed gas content data on 11 mines.

Jan 1, 1984

By Lawrence Y. Marks

During the mineral survey of the Bob Marshall Wilderness and study areas by the author in 1971, 1973, 1974, and 1976 (Marks, 1978), the area designated Reservoir-North (RARE II No. H1-485) in January, 1979, (U.S. Forest Service, 1979) was examined, along with other lands adjacent to the earlier study areas. However, the 1978 open-file report covered only areas originally designated for study. The present report on Reservoir-North is based on earlier work. No work has been done in the area since 1976. Mineral Appraisal Reservoir-North RARE II area (No. H1-485) is in the Northern Disturbed Belt which has been identified as having high potential for natural gas accumulations and lesser potential for oil accumulations (Mudge, 1978). Oil and gas lease applications in the area, indicate interest by oil companies.

Jan 1, 1981

By Robert H. Peters, George R. Bockosh, Barbara Fotta

This paper was commissioned by the Japan Technical Cooperation Center for Coal Resources Development. It is to be published in a proceedings following a series of presentations to Japanese coal officials in February 1997. The paper focuses primarily on summarizing the past 20 years of U.S. research on promising techniques for ensuring that underground coal miners work safely. These techniques can be grouped into three major categories: management, workplace design, and training. Each technique is described, and the results of efforts to apply the technique at underground coal mines are summarized. Recent statistics on accidents and productivity in U.S. underground coal mining operations are presented before the overview of research findings is given. Because Japanese coal mines are using the longwall method of coal extraction, separate statistics are given for U.S. longwall versus room-and-pillar coal mining operations.

By Ralph B. Adair

The Bureau of Mines conducted laboratory and small-scale, continuous tests of weathered mica-pegmatite ores from Randolph County, Ala., to determine the feasibility of recovering commercial-grade mica concentrates by flotation. Two flotation methods were used in continuous tests for recovery of mica. One method utilized acid-cationic flotation for the recovery of coarse mica and alkaline-anionic-cationic flotation for recovering fine mica. This method yielded mica concentrates containing 98.6 percent mica with a recovery of 85.9 percent. The other method was based on the Bureau-developed alkaline-anionic-cationic method, and yielded concentrates containing 97.5 percent mica with a recovery of over 90 percent. In both methods, preconcentration of the ground ore on a Humphreys spiral was employed to reject over half of the feed in a product virtually free of mica.

Jan 1, 1968

By R. E. Head, Virgil Miller

"Under existing conditions in the treatment of oxidized lead ores containing small quantities of molybdenum no provision is made for the recovery of the molybdenum. Considerable quantities of this important element are lost in the slags of the lead smelters and constitute an economic waste. There is little or no probability that slag dumps containing molybdenum in small quantities could be economically treated for the recovery of the element, and steps for the prevention of waste in this respect must be taken prior to smelter treatment.Wulfenite, lead molybdate (PbMo04), and molybdite, molybdic ocher (Mo03), are the molybdenum minerals most abundantly found in deposits of oxidized lead ores. Wulfenite contains 39.3 per cent molybdenum trioxide and 60.7 per cent lead oxide; molybdite contains 66.7 per cent molybdenum and 33.3 per cent oxygen. Plumbojarosite, argentojarosite, cerussite, and occasionally anglesite are commonly associated with wulfenite ores, and the oxidized iron content is usually fairly high.The recent discovery and development of a body of wulfenite ore in the Star district near Milford led to a cursory microscopic examination of samples of the ore, followed by a few preliminary tests which had for their object the separation and recovery of the lead and molybdenum in separate products.The microscopic examination showed that the samples used in the work were composed of wulfenite, plumbojarosite, and a small quantity of cerussite, and indicated that the iron content was quite high. The ore was porous and yellowish-brown; crystals of wulfenite appeared to be quite uniformly distributed through it, and this mineral and plumbojarosite (Pb0.3Fe203.4S03.6H20) apparently accounted for the major part of the lead content, although lead"

Sep 1, 1928

By Wilbert T. Malenka

In its search for a highly productive mining system for anthracite beds pitching from 100 to 200, where conventional mobile equipment cannot be used) the Bureau initiated a longwall project by introducing a shearer drum cutter loader of European origin. Because of the undulating nature of the roof and floor and changing bed thicknesses, the machine proved inflexible and extra work was required in lifting bottom coal and blasting top coal.

Jan 1, 1966

By D. Cummins

This Information Circular presents a brief history of the lead-acid battery and describes ways to prevent serious injury from battery explosions when servicing and charging lead-acid batteries, particularly in the surface mining industry. The Mining Safety and Health Administration (MSHA), U.S. Consumer Product Safety Commission, battery manufacturers, and the mining industry have all contributed information as well as recommendations for injury-free handling for this report.

Jan 1, 1980

By W. F. Hughes

The thermodynamics of an electromagnetic field-fluid interaction system is discussed. A review of the thermodynamics of linear media (the permittivity and permeability taken as functions of density and temperature) is presented; then an extension is made to nonlinear media (the permittivity and permeability taken as functions of the fields). Expressions for thermodynamic properties and reversible work are derived and the first law of thermodynamics for magnetohydrodynamic flow is discussed.

Jan 1, 1968

By William P. Diamonds, David C. Oyler

Stimulated vertical boreholes are an effective means of removing gas from coalbeds in advance of mining. This Bureau of Mines report examines the coal mine roof damage potential of stimulation treatments. Twenty-two Government-sponsored stimulation treatments have been mined through to determine the effects on the coalbed and roof strata. Vertical fractures in the coalbed were discernible for most treatments and horizontal fractures were present for about half of the stimulations. Sand-propped vertical fractures were usually short in lateral extent. Evidence of stimulation fluid movement could generally be traced beyond the maximum extent of sand-filled fractures when fluorescent paint was added to the treatment fluids. The maximum lateral extent for a sand-filled vertical fracture was 416 ft and a paint-coated vertical fracture extended 630 ft. Horizontal fractures were generally found within bedding planes, most commonly on top of the coalbed. The maximum lateral extent for a horizontal fracture was 265 ft at a coalbed depth of 630 ft. Horizontal fractures have been found to occur as deep as 1,145 ft. Penetration of strata overlying coalbeds was observed in nearly half of the treatments intercepted. Most of these occurrences have been interpreted to be penetrations into preexisting joints. No roof falls or adverse mining conditions were encountered that could be attributed to the stimulations.

Jan 1, 1987