Search Documents

By Michael D. Fenton

The very modest-sized mineral industry of Afghanistan was burdened for another year with problems of internal strife occassioned by the presence of Soviet armed forces. Despite this, production of the few traditional commodities continued, and the mineral industry moved to develop additional mines and plants for both traditional and new products with considerable technical and construction assistance from the U.S.S.R. Among the limited range of mineral commodities for which production was reported, there were no startling changes between 1984 and 1985. Production of both coal and natural gas advanced only slightly, despite substantially higher 5-year plan goals, and cement output was down marginally. Probably the most significant development in 1985 was the Possibility that mine and/or smelter production of copper was initiated during the year.

Jan 1, 1987

By Ralph L. Brown

As a preliminary step in a recent study4 of the phenols present in a low-temperature tar, the writers prepared the hydroxyacetic derivatives of the simpler available members of the phenol series in order to obtain material to assist in fixing the identity of similar derivatives obtained from the phenols of the tar. When comparing the melting points of the pure derivatives we had made with those given in the literature we were unable to find the characteristics of one of the xylenol derivatives which we had prepared--namely the 1, 3 dimethyl-2-phenoxyacetic acid, In the belief that the compound does not appear in the literature we are presenting these notes on its preparation and its melting point. The hydroxyacetic derivatives are easily prepared and in good yield, and are useful in studying mixtures of phenols. The 1, 3 dimethyl-2-phenoxyacetic acid makes the fifth of the six isomeric derivatives to be reported in the literature. Gluud and Breuer report the preparation of the 1, 3, 4, the 1, 4, 2, and the 1, 2, 4 derivatives. A fourth isomer-¬the symmentrical 1, 3, 5--has been reported by Schutz6, although no record of it occurs in the indexes. The remaining derivative--the 1, 2, 8-has not, been found and it is now being synthesized in the Organic Chemistry Laboratory of the. Pittsburgh Experiment Station. It is true, however, that from a phenolic fraction boiling 215.9 to 2180 isolated from natural petroleum, Tanaka and Kobayashi7 obtained a hydroxyacetic derivative melting at 103.3°. They state that this is the 1, 2, dime ethyl-3-phenoxyacetic acid but present no evidence for the assertion. The known derivatives are summarized in Table 1 following;

Jan 1, 1929

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By D. J. Bauer, V. E. Shaw

Bastnasite concentrate was processed to recover total rare - earth content and obtain high - purity ceric nitrate . Reaction of the concentrate with 45 percent caustic soda for 1 hour at 180 ° C in stainless steel vessels resulted in 99 - percent conversion to rare - earth hydroxides . A drying step followed by solution in nitric acid produced a tetravalent cerium fraction amenable to extraction with TBP . Single- stage separatory funnel experiments resulted in 90 -percent recovery of ceric nitrate at a purity of 99.9 percent . Fractional extraction in pressure - bubbler columns resulted in 98.5 - percent recovery of 99.5 -percent - pure ceric nitrate .

Jan 1, 1964

By T. J. Ballard

Corundum is a natural alumina (A120 ) and is next to the diamond in hardness . Except for the gem varieties , it is used principally as an abrasive , chiefly in grinding , dressing , and polishing metals and optical glass . Natural corundum is preferred to artificial abrasives for certain specialized jobs . Most of the corundum ( excluding emery ) mined in the United States came from the Corundum Hill mine in North Carolina and the Laurel Creek mine in Georgia . The Corundum Hill mine provided over half of the domestic production of corundum prior to 1900. Since 1900 , the importation of foreign corundum and the manufacture of artificial abrasives caused the decline of corundum mining in the United States .

Mar 1, 1947

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By L. C. IlsLey

As part of its work for the improvement of safety conditions in mines , the Bureau of Mines has undertaken to establish a list of permissible storage - battery locomotives for use in gaseous mines , and , to this end , has issued Schedule 15 , "Procedure for Establishing a List of Permissible Storage -Battery Locomotives for Use in Gaseous Mines . " Up to the present time , two approvals * have been issued under this Schedule , and considerable testing work done on four other applications which have been made for approval . Prior to the publication of Schedule 15 , the Bureau conducted both field and laboratory investigations to determine the hazard from the batteries used in mine locomotives . ** These investigations indicated that the safety of the locomotive would depend largely on proper care of the battery , also on the use of a battery as mechanically rugged as possible . For this reason the Bureau staff , in testing locomotives submitted for approval , considered it advisable to subject the batteries to a jarring or bumping test to prove their adequacy as regards mechanical endurance and ruggedness . These tests on the batteries of the locomotives are described below.

May 1, 1922

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By J. D. Davis

From the chemist's point of view it would be ideal if specifications for coke for any stated purpose could be written on the basis of chemical composition and burning characteristics. Unfortunately this is not possible. In fact, the physical properties of a coke are often of such major importance as to render any specified chemical requirements totally inadequate to show the quality of coke desired. For example, a furnace coke may admirably fill all chemical requirements, such as for low phosphorus, sulphur, moisture, and high fixed carbon, and still be too soft to support the burden of the furnace without excessive crushing. Again, a domestic coke though a good fuel as judged from Chemical analysis, may be of unmarketable size. Thus one can not define the quality of a coke for a specified purpose without taking into account both its chemical and physical characteristics even when this has been done the specification may fail because neither coke user nor producer can accurately define by quantitative tests the qualities most desired. In other words, there is need of accurate test methods for measuring the properties of coke and, what is equally important, for correlating the results with the behavior of the coke in use. Coke quality is determined by the kind of coal used, the coking process, and the type of equipment used in the coking process. Chemical analysis of the coals, together with small-scale coking tests, will give a good indication of their suitability; but, in general, coke must be produced on an industrial scale and tested in the equipment for which it is intended before conclusive information as to its quality is obtained.

Jan 1, 1928

Provide a strategy for calculating optimum distribution of selected sensors for detecting underground mine fires. Approach The Bureau of Mines performed research to determine adequate distribution of product-of-combustion (POC) fire sensors within mine entries. This placement strategy would improve the miner's chances for escape by locating sensors where they would most effectively, quickly, and efficiently detect fires resulting from coal or wood combustion. Spacing of Sensors Placement strategy guidelines were based on the performance of 160 F heat sensors with ideal operating characteristics which were placed at intervals of ten feet in underground mine entries. Data obtained from full-scale mine fires were used to estimate fire sizes and alarm activation times for the heat sensors. Various equations were then developed to determine spacing requirements for any fire detection system installed in entries of varying heights, widths, and ventilation rates.

Jan 1, 1983

By Marie Farnsworth

"The Anhydrite ProblemThe Nonmetallic Minerals Experiment station of the Bureau of Mines at Rutgers University, New Brunswick, N. J. has recently undertaken a study of the chemical and physical properties of anhydrite having in view its wider utilization anhydrite (CaSO4) in contact with water at ordinary temperature and pressure rehydrates, slowly forming gypsum (CaSO4.2H42O). In nature this is an extremely slow process, and laboratory experiments are being conducted to determine methods of accelerating the rehydration. The tests recorded herein cover one this study, and while they are negative in character in so far as the major problem is concerned, certain facts established by the tests, bearing on the stability relations of gypsum and anhydrite seem sufficiently important to be placed on record.Early Researches on Gypsum and Anhydrite.It is to Lavoisiar that we are the first scientific study of the calculation and hardening of plaster of Paris. He sums up his experiments in the following passage: ""If gypsum, which has been deprived of its water of by means of heat, is again treated with water (to make what is commonly called mortar) it takes it up with avidity, rapid and irregular crystallization occurs, and the small crystals which are formed are so entangled in each other that a very hard mass results."" Later, he observed that the dehydration of gypsum occurs in two stages: three-fourths of the combined water is much more easily driven out than the last fourth. LeChatalier first determined the temperature decomposition accurately, his method was as follows: Pulverized gypsum was placed in a glass tube in the middle of a paraffin bath, the temperature of which was raised in a progressive and regular manner. A thermometer gave at each instant the temperature the salt, and the passage of the mercury column past each division of —co. was cared by a registering chronograph. The rise in temperature was except at 128°C. and 168°C. where breaks occurred."

Nov 1, 1924

By W. Wan, R. V. Ramani, J. M. Mutmansky

"Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer, and distribution of DPM in coal mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Analyzed using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study is presented.With diesel equipment holding an important place in underground coal mining and growing in use over time, it is important to develop and improve controls of the exhaust emissions, especially diesel particulate matter (DPM), to further reduce potential health hazards. The proper design and maintenance of diesel engines and on¬board control procedures are paramount requirements for controlling DPM successfully. There is also, however, a significant reduction potential in terms of personal exposure that can be realized by managing the DPM that gets into the airstream. Strategic design of the mining, ventilation, and equipment implementation systems remain essential for efficiently reducing the DPM concentrations.Modeling the effect of diesel exhaust contaminants upon the mine atmospheric quality will permit improved health and safety design of the overall mining and ventilation systems. Numerous studies have been performed to model the distribution/transport of gaseous and particulate emissions in the underground mine atmosphere and some very sophisticated convection/diffusion models have been developed (Skobunov, 1974; Thakur, 1974; Stefanko and Ramani, 1975; Wala, 1980; Bandopadhyay and Ramani, 1983). Most of these models were developed for a single airway or based on the assumption that the ventilation network of a mining section can be approximately represented by a single intake and a single return. The complexity of most models of the convection/diffusion type and the mobility aspect of diesel haulage units made a detailed emissions model very difficult to develop.The current model is an attempt to fill the need for a more generic tool applicable to mining sections employing multiple mobile diesel units by simplifying the convection-diffusion model to a convection-only model. The simplification is based on the fact that the diffusion coefficient will affect only the transient environmental contaminant concentrations with little or no affect on the time-weighted-average concentrations over a relatively long period such as a working shift (Lee et al., 1994). In view of the difficulties involved in mathematical modeling, the approach here is developing and using a computer simulation model. A PC-based FORTRAN 77 simulation model for the analysis of mining systems with multiple diesel sources and any ventilation network configuration was developed to study the distribution/transport of DPM in mine airways, evaluate methods of reducing DPM concentrations, and explore modifications to existing mining practice."

Dec 1, 1996

By Alan H. Goode

The advancement of high-temperature drilling fluid technology for application in geothermal environments is part of the Bureau of Mines program for more efficient development of our Nation's energy resources. The bentonite constituent of water-base drilling fluids is sensitive to destabilization by high-temperature and salinity. A substitute material for bentonite, phosphate slime, which is reported to be saline resistant, was considered. These studies show that spray-dried slime suspensions have more favorable rheological behavior, but poorer filtration properties, as compared with bentonite suspensions.

Jan 1, 1975

By T. E. Green

The Bureau of Mines Heavy Metals Program emphasizes the need for improved analytical methods for gold determination. A commercially available ion exchange resin with high selectivity for gold was investigated as a potential method to collect gold from solution. The resin was found to quantitatively collect gold from acid solutions over a wide range of acid concentrations. Common metals were not collected by the resin nor did they seriously interfere with the collection of gold. X-ray spectrographic and neutron activation methods based on the use of papers containing this resin are proposed.

Jan 1, 1970

By Christopher C. Jobes, N. Kumar Kittusamy, Alan G. Mayton, Dean H. Ambrose

Researchers with the National Institute for Occupational Safety and Health (NIOSH) conducted a systematic study to evaluate seat designs on low- and mid-coal-seam shuttle cars. The purpose was to gather additional data to support earlier findings that NIOSH seats, with unique viscoelastic foam padding, are indeed improved designs for coal mine shuttle cars. This study included a larger sample of shuttle car operators than a prior NIOSH investigation. Eight shuttle car operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers then compared the operators’ perceptions with field-measured levels of vehicle jarring/jolting. Seven seat designs were evaluated on low- and mid-coal-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. These seat designs comprised the one already in use on each vehicle and five NIOSH designs. Experimental data were collected using accelerometers, signal conditioning amplifiers, and filters connected to a data recorder, whereas subjective data were gathered via a visual analog scale (VAS) and a questionnaire. Field trials included shuttle cars operating under full- and no-load conditions. VAS responses indicated that NIOSH-designed seats performed better relative to comfort and isolation from vehicle jarring/jolting than the existing seats used in the shuttle cars. Both mid- and low-coal-seam shuttle car operators, during no-load and full-load conditions, rated lower levels of jarring/jolting with the NIOSH seat design. Questionnaire responses indicated that shuttle car operators rated NIOSH seat designs as more comfortable. Vehicle operators most frequently suggested the addition of armrests as a way to improve the seats on the mid-seam shuttle car. The quantitative levels of vehicle jarring/jolting for the no-load condition (more severe condition for vehicle operation) showed that NIOSH seats for the mid-coal-seam shuttle car performed better than the existing seat in terms of peak acceleration and crest factor. Similarly, for the low-coal-seam shuttle car, NIOSH seats performed better than the existing seat in terms of peak acceleration, root-mean-square (RMS) acceleration, and crest factor.

Jan 11, 2006

By Gary L. Mowrey, William D. Monaghan, George F. Persetic, Gregory M. Molinda

Ground penetrating radar (GPR) has been investigated by the U.S. Bureau of Mines Pittsburgh Research Center for its potential to determine rod hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth to determine the value of GPR for roof hazard detection. The resolution of the current systems allows detection of gross roof fractures (>6A mm (>0.25 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologics changes in the roof. Differences in data quality are discussed, as well as suggestion for collecting improved data.

Jan 1, 1996

By John Nagy

This circular has been prepared for the guidance of safety engineers, shot firers, and coal-mine inspectors concerning multiple blasting with short-delay (millisecond-delay) detonators. These special precautions are suggested in addition to those normally followed in blasting, as outlined in the Federal Mine Safety Codes 5 6/ and in Miners' Circular 58.7/ INTRODUCTION The use of short-delay blasting has been proposed for promoting safety and increasing the rate of production in coal mining. Ideally, short-delay blasting, as compared with equivalent single-shot blasting, reduces exposure of the shot firer to dust, fumes, and weakened roof; as compared with equivalent simultaneous blasting, it reduces roof disturbance.

Jan 1, 1959

Determine the minimum waterflow rate needed for effective control of dust produced by cutting machines used to mine water-soluble ores. Approach Conventional wet-bar cutting techniques were studied to evaluate their dust control performance, and the optimum water flow needed for dust suppression was determined. Wet-bar type cutting techniques are used to help control mine dust by keeping the cutting chain wet. As the chain cuts the kerf, it dampens the dust produced by the cutting action at the point of generation. The Bureau, under contract, evaluated three basic wet-bar techniques, as shown in the diagram: water-trickle system A uses a gravity-feed or low-pressure (less than 50 psi) pump to send water through the bar and to discharge it at the bar tip. Water-spray system B uses a low-pressure spray nozzle located at the front of the cutter head. For protection the nozzle can be located within the cutter

Jan 1, 1982