Search Documents

Provide the mining industry with a method for determining the gas content of ore bodies and associated strata for use in mine planning, Approach Samples of various rock types are collected and tested to determine gas content in conjunction with sample size, the collection method (i.e. whether the sample was collected from a core sample or by hand) mine gas emission, and the geologic location from which the sample was taken, such as near a fault, outburst area, or other geologic anomaly. How It Works Two methods were developed by the Bureau of Mines to determine the gas contents of rock samples. The first method developed involved dissolving minerals to measure gas emission. This method, however, can only be used with soluble minerals. A second method, therefore, was developed for use with insoluble minerals. With this method, the sample is crushed in a ball mill. Although the dissolution method is faster and more accurate to use, the crushing method is also advantageous because its use can more closely approximate a mining situation; the sample is crushed as in mining and the amount of gas released relates to the amount of gas that would be released during a mining operation. The dissolution method is applied to soluble minerals, such as rock, salt, or trona, in a sealed chamber. Gases released during dissolution are collected for analysis by gas chromatography. One advantage in using the dissolution method is that the test apparatus is relatively inexpensive. In addition, test can be performed at any scale, from single crystal samples to a solution mining operation.

Jan 1, 1983

Enhance the critical skill of hazard recognition among miners by providing quality training that can help jot performance and lead to a higher degree of safety in the workplace. Background In mining, as in many other occupations, the safety of the worker depends on his or her ability to recognize hazards in the workplace. Some of the information needed by the miner for recognizing potential areas of danger is available in the form of visual cues found throughout the mine. One aspect of the dynamic mine environment it which the task of hazard recognition is critical for al workers is that of ground control. Regardless of job responsibilities, every worker is continuously exposed to roof rib, and floor hazards. Fatality injury data for the "underground coal" segment of the mining industry continue to show that about half of all fatalities are due to falls of ground each year. It is hypothesized that some of these accident, can be prevented if miners are better able to recognize visual cues that forewarn of potential roof and rib problems.

Jan 1, 1992

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

By John J. Sammarco

As part of a project to automate coal extraction, computer control of a continuous mining machine test bed has been developed and tested by the Bureau of Mines. A computer system and control software were developed for accurate positioning of the conveyor elevation and swing, stabilizer jack, gathering head, and shear elevation. Tramming actions are also controlled by the computer. The computer system was designed to access data from sensors installed on a continuous miner and to interface with the existing control circuits of the miner. Testing in free space was used to characterize the operation of the machine. From this information, control algorithms were written and stored in the computer. The ability to control each function of the continuous miner with a high degree of accuracy and stability was successfully demonstrated in a series of tests in free space and in mining a block of simulated coal. In the mining of simulated coal, the cutting drum was instructed to position the shearer at the top of the block and shear down to the bottom under closed loop control. The cutting drum came within 0.27 in of the top and within 0.49 in of the bottom of the block for this shearing test.

Jan 1, 1988

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

Reduce workers' dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the boom of a continuous miner at the conveyor throat. Dusty air from the face area is drawn through the scrubber and cleaned air discharged into the return. How it Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator and contaminated air behind the line curtain to the return. The problem with exhaust ventilation is that the line curtain should be within 10 ft of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back towards the operator. An effective way of removing this dust is with a scrubber mounted on the mining machine.

Jan 1, 1988

To more rapidly and economically prepare solutions for chemical analysis, of a wide range of ores, slags, minerals, and metals. Approach A Simple pressure-dissolution system was devised using an inexpensive, heavy wall plastic bottle containing a sample in an acid medium. Using the technique, a complex silicate sample can be dissolved in less than 1 hour. How It Works A weighed portion of a sample, ground to minus 100-mesh, is placed into a polycarbonate or polysulfone plastic bottle. A mixture of hydrochloric acid, nitric acid, and hydrofluoric acid then is added. The bottle threads are wrapped with a layer of Teflon tape to prevent leakage, and the bottle cap is screwed on tightly. The sealed bottle is placed in a balling water bath. In the hot water, the plastic bottle acts as a pressure vessel to contain the pressure generated inside it. This technique should only be used by trained experienced people who are familiar with the hazards of hot acids under pressure. After being cooled in cold water, the resulting solution is brought to the final volume by adding 1.5 weight-percent boric acid solution to the bottle. The cap is replaced, and the bottle and solution is reheated. Precipitated fluorides, as well as any residue, are dissolved by the fluoride-boric acid reaction. The resulting clear solution then is suitable for spectro-photometric examination or other analysis.

Jan 1, 1980

By J. D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings in the form of stress and deflection coefficients from which bending, axial, shear, and boundary stresses, moments, thrusts, and shear forces, and structural deflections can be determined at any point on the lining. Results were obtained by structural analyses of nine concrete-lined tunnel configurations subjected to 22 biaxial load conditions. The tunnel configurations include three basic shapes, circular, rectangular, and horse-shoe, with dimensions based on designs evolved by the mining industry. These analyses were made by the direct stiffness matrix method, a computer-oriented procedure. Numerical results agree closely with those obtained experimentally.

Jan 1, 1969

By M. E. Tyrrell

Work in this investigation was undertaken by the Bureau of Mines to demonstrate how waste glass might be utilized to lower the required firing temperature and firing time of structural clay products. Mixtures of waste glass and common clays were formed by stiff-mud extrusion and fired to the temperature required to produce a body having 6 to 7 percent absorption. Substitution of glass for one-half of the clay in a red body reduced the firing temperature 500° F, which made possible a 30-percent increase in production; in a tan body, the firing temperature was reduced 400° F, which made possible a 23-percent increase in production.

Jan 1, 1972

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Condition-based maintenance (CBM) of industrial equipment is generally recognized as being the most cost-effective means for improving equipment availability. However, prerequisite to successful implementation of CBM is a reliable detector of failing components. One such detector, termed the effective negative-sequence impedance, had previously been identified as an indicator of induction motor stator winding degradation. However, a limitation of this detector is that it does not change in a predicable manner under certain motor operating conditions. This paper presents an experimental investigation of an improved technique for on-line detection of induction motor stator winding degradation. The paper begins with a brief description of the detectors, followed by a detailed description of the experimental setup, the experiments conducted, and results.

Provide a means of evaluating the in place structural properties of coal seams and coal measure rocks in advance of mining. Approach Develop a sonic logging probe for use in dry wells, a condition common to shallow wells and semi-arid coal regions. How It Works The Bureaus' sonic probe differs from conventional sonic probes because it does not require fluid in the well to couple sonic vibrations to the drill hole wall. A self-contained hydraulic system forces pistons containing the measurement transducers against the wall and clamps them in position until the sonic waveform information has been recorded. The pistons are then retracted and the probe is raised or lowered in the well as required. In the clamped position, the piezoceramic transmitter emits a sonic pulse which travels along the drill hole wall and is detected at the receivers in the form of compressional (P) and shear (S) wave motion. The receivers are designed to be sensitive to either the (P) wave or (S) wave motion as determined by the operator so that discrimination between the two wave types is improved by comparison of the respective output channels, and the travel time between transmitter and detectors can be accurately determined. Use of two receiver stations eliminates errors in timing of pulse travel because of electronic delays inherent in the probe.

Jan 1, 1981

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant's group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

By John T. Aydelotte, Martin J. Gavin

" Oil shale contains little or no oil as such , but it contains an organic material from which oil may be produced by destructive distillation" . This statement , or others conveying the same meaning, appears in many popular and techni cal articles on oil shale . It is based on the belief that the ordinary solvents of petroleum have but little action on the organic substances contained in oil- yielding shales , although on distillation these same shales may yield upwards of 50 gallons of crude shale oil per ton . A 50 - gallon shale thus yields by distillation 18.73 per cent of its weight as oil ( assuming the specific gravity of the oil to be 0.900 ) , although only a relatively small part of this can be recovered by extraction with such solvents as chloroform , carbon tetrachloride , and the like . In the course of certain experiments designed to determine the solubilities of different shales after they had begun to yield oil by distillation , it was found desirable to determine the quantity dissolved from certain unheated shales by various solvents , at or near the boiling points of these solvents . The method used and results obtained are presented below. These experiments were made in connection with the oil - shale investigations being conducted by the U. S. Bureau of Mines , in cooperation with the States of Colorado and Utah .

Jan 1, 1922

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK - ALTIMETER SURVEY WITHOUT ALTMETER TEMPERATURE CORRECTION 1 BAS 8: 22 1391 1391 53. 49.

Jan 1, 1977