Search Documents

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By George E. Blandford

A deterministic model to assess the hydrologic impact of small watersheds subjected to unsteady storm events is presented. The overland flow model is based on the kinematic wave approximation coupled with a Green-Ampt infiltration equation. The Green-Ampt infiltration parameters are estimated using the USDA-ARS parameter estimation technique which is based on soil moisture-tension data. A Galerkin finite element formulation of the kinematic wave approximation is presented for the deterministic analysis of overland flow on small watersheds. The finite element formulation includes linear, quadratic and cubic Lagrangian one-dimensional spatial elements. A linear time variation is assumed which includes both explicit and implicit time marching algorithms, depending on the choice of the time weighting parameter. The implicit time algorithms result in a system of nonlinear equations which are evaluated using a modified Newton-Raphson iteration scheme. Initial solution estimates are generated using a linear finite difference procedure. The coupled infiltration overland flow model is tested using storm data for impervious surfaces, a laboratory soil flume, and two natural, USDA-ARS experimental watersheds.

Jan 1, 1983

Although alternating-current (a.-c.) power systems and equipment have been used in coal mining for many years, most mines in the United States are powered mainly by direct current (d.-c.). There are several logical reasons for this, but the use of d.-c, equipment is, in most instances, a direct outgrowth of the original practice of using such power for haulage systems. For traction equipment such as the electric trolley locomotive the d.-c. motor has ideal operating characteristics, and thus it has been widely used for haulage locomotive service. The first efforts at electrification of coal mines started with the haulage system and from there branched out to include the many types of electrically powered mining machinery used in the industry today.

Jan 1, 1960

Consumption and intensity of use trends for 12 metals, by industrial end use, were estimated for 1972 through 1982 by the Bureau of Mines and U.S. Department of Commerce. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following 4 of the 12 metals increased from 1972 to 1982 as follows: aluminum, 1.00%; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83%; titanium, 7.82%; and tungsten, 6.09%. Consumption for the remaining eight metals decreased at average annual rates ranging from 0.58% (copper) to 5.37% (manganese).

Jan 1, 1986

By P. D. Kovscek

High-pressure streams of water, known as water jets, can be used to improve the cutting efficiency of mechanical bits. During prior testing by the Bureau of Mines, the cutting performance of a longwall shearer, equipped for water-jet-assisted cutting, was evaluated. The performance of the shearer did not improve while using water jet assist because the pressure of the water delivered to the rock surface was inadequate. The study, described in this report, resulted in a determination of the major cause of water pressure loss on the shearer, and an evaluation of the techniques for increasing the water pressure at the rock surface. The results show that the major pressure loss, which occurred between the nozzle and rock surface, is directly affected by the amount of fluid turbulence that develops just upstream from the nozzle. Preventing a sudden change in the direction of the flow channel can increase the stagnation pressure as much as 400 pct. Smoothing the surface of the flow channel in the shearer bit block would increase the stagnation pressure delivered to the rock surface by 35 pet.

Jan 1, 1989

By V. R. Spironello

The Bureau of Mines is conducting studies of the slags related to ferrous technology to evaluate acceptable substitutes for the auxiliary flux, mineral fluorspar, in foundry operations. This work is directed toward the Bureau's goal of minimizing the Nation's dependence on scarce and critical minerals Comparative basic practice cupola (18-inch-ID) trials were made to evaluate a waste material called "used potlining," which contains significant levels of fluorine, sodium, and aluminum in various compounds. Used potlining is recovered from alumina reduction cells after its useful life, and was supplied by the Aluminum Co. of America (Alcoa) to the Bureau for evaluation. The material in the lump and pelletized form (with limestone) provided extremely fluid slags based on visual observation during cupola operation. No adverse effects were found on cupola performance, metal and slag chemistry, the environment, or mechanical properties of the castings produced. Fluorine recovery in the slag was equal to, or higher than, that of fluorspar; fluorine losses to the scrubber water and solids were lower. The acidity of the scrubber Hater was somewhat neutralized. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag and visual inspection. The recovery of sodium in the slag, presumably as the oxide, significantly increased slag fluidity, suggesting that less than equivalent fluorine may be required. There was no contamination of the gray iron by the aluminum from the used potlining. Used potlining was completely satisfactory as a substitute for fluorspar in cupola ironmelting.

Jan 1, 1981

Provide reasonably priced, reliable fire protection for front-end loaders. Approach Automatic fire sensing and suppression systems were developed and ruggedized for use on front-end loaders operating in harsh mine environments. How It Works Temperature sensors mounted in the loader's engine, transmission, and articulation areas detect the heat from a fire while it is still small and controllable. This triggers the release of the ABC class dry chemical extinguishing agent through a fixed piping system onto the fire. The system can also be manually activated from either the cab or ground level. Locations of the principal components of the system are shown in the drawing. Two control subsystems were designed to respond to varying fire protection needs and mine conditions. One subsystem only initiates discharge of the extinguishing agent. The other subsystem initiates visual and audible operator alarms if there is a fire sensed or if there is a fault in the control circuit.

Jan 1, 1979

A spectrographic procedure applicable to the semiquantitative determination of 29 elements in tungsten is presented. The method is designed to give estimates of impurity concentrations up to 500 p.p.m. Limits of detectability range from 0.3 p.p.m. for the more sensitive elements to 100 p.p.m. for the less sensitive ones. Tungsten metal samples varying in particle size from minus 300-to 30-mesh are excited in the presence of 5 percent germanium with a direct current arc. Germanium acts to stabilize the arc, minimizes the volatilization of tungsten, and serves as an efficient carrier to sweep impurities from the tungsten into the excitation zone. Curves are presented that show the volatilization behavior of germanium, tungsten, and impurities in tungsten at different concentration levels. Data obtained were used as guides in establishing the method of analysis. In the absence of established reliable analytical procedures for determining many impurities in tungsten in the parts per million concentration range, the spectrographic method described here should prove to be helpful in evaluating high-purity tungsten.

Jan 1, 1961

By M. A. Reyes

This experiment investigated the effects of different machine mounted area lighting technologies on visual performance. The primary objective was to conduct a comparative evaluation of the lighting technologies based on the visual performance of thirty-six human subjects in a simulated underground mine environment. Incandescent (Incand), fluorescent (Fluor), and light-emitting diode (LED) technologies were used to create four lighting combinations. Visual performance was quantified for the detection of movement in the peripheral field of view and the identification of ground hazards. Measurements were made of the speed [response time measured in milliseconds (ms)], the accuracy (the number of targets and objects missed), and the subjective discomfort rating of the glare experienced for each lighting combination. A secondary objective explored the effects of aging on visual performance. The results indicate that lighting combinations which consisted of LED area lights significantly improved visual performance for the detection of hazards found in the peripheral field of view, as well as those found on the ground. They furthermore, indicate that age plays a significant role in visual performance.

Jan 1, 2009

By N. A. Eilertsen

This report describes field investigations conducted in 1953 of two occurrences of manganese and a separate magnetic anomaly in the Southern manganese district of Aroostook County, vicinity of Houlton, Maine -the Pierce deposits, in Hammond Plantation Township; the Burnham anomaly, also in Hammond Plantation; and the Nickerson-Farm prospect in Hodgdon Township. The manganese occurs in a thinly laminated sedimentary rock containing manganiferous carbonate interlayered with fine-grained metamorphosed sediment, rich in chlorite or hematite. The surrounding rocks are mostly dark gray-green slates. Samples composited for metallurgical testing from the Pierce deposits and the Nickerson-Farm prospect assayed 9.0 to 12.3 percent of manganese. More than 90 percent of the manganese could be extracted with sulfuric acid, but in most instances 30 to 40 percent of the iron was also extracted. Leaching tests indicated that, after being reduced in a hydrogen stmosphere at 600° C., about 85 percent of the manganese could be selectively extracted by a solution of ammonia-ammonium carbonate with iron extraction of only 14 percent.

Jan 1, 1958

By K. A. Johnson

Marshall and Bird have published the results of a cooperative investigation by the Bureau of Mines in which they developed a procedure for measuring the agglutinating value of coal.4 As stated in their paper, the procedure outlined was suggested by the early worn of Richters5 and Campredon,6 whose procedures were hurriedly modified to meet the need of an investigation then in progress. Since the publicatien of that paper, further work has been done in an attempt to show how the variables involved affect the concordance of the results, in order that such results may be obtained in different laboratories. Briefly, Marshall and Bird's method for determining the agglutinating value of coal consists in carbonizing an intimate mixture of 10 parts by weight of sand and 1 part by weight of coal in a porcelain crucible at a uniform temperature of 950° C. in a, vertical, cylindrical, electrically-heated furnace. After carbonization, the resultant buttons are crushed in a testing machine and the breaking strengths recorded in grams. The agglutinating value reported is the average breaking strength of 10 buttons. The coal for the test is prepared by crushing to pass a 100-mesh screen. The sand used as a diluent is sized between 40 and 50 mesh sieves with openings of 0.381 icon and 0.279 millimeters, respectively.

Jan 1, 1930

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use in a helicopter. Tests showed that EM signals from lightweight (314 lb) transmitters could be detected both on the surface and from a helicopter through -2 as much as 1650 ft of relatively high conductivity (2 X 10 mhos/m) over- burden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 7, 1973

By D. C. Dahlin

The Bureau of Mines conducted laboratory batch beneficiation tests on samples from four potential platinum resources in southeastern Alaska to concentrate platinum and other precious metals. Thin Investigation was done as part of the mission of the Bureau to insure an adequate supply of minerals to meet the Nation's needs. Petrographic studies and beneficiation methods including gravity concentration, froth flotation, and magnetic separation were used to determine mineral association and to attempt to concentrate the platinum values with a primary mineral value such as chromite, copper sulfide, or magnetite. A high-graded sample from the Salt Chuck copper sulfide deposit yielded the platinum-group metal concentrate; the maximum grade attained was 0.04 oz Pt and 1.5 oz Pd per ton of high-grade copper sulfide concentrate. The other samples yielded low-grade primary mineral concentrates with low platinum-group values, and/or the platinum-group metals did not concentrate with the primary mineral value.

Jan 1, 1981

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By C. H. Schack, A. O. Ipsen, H. G. Poole

"INTRODUCTION In the course of the investigation of manganese mineral occurrences in continental United States, the Bureau of Mines has collected several lots of ore from properties in the vicinity of Long Valley, Ariz. The ore occurs as irregular and random pockets in a brecciated zone. As only high-grade portions of the deposits obtained by selective mining would be acceptable as commercial-grade manganese ores, an investigation was made to determine amenability of the ores to concentration by ore-dressing methods. Several types of ores, differing in grade and mineral associations, were studied.Ores from the Vaiazza property are of special interest, owing to the successful application of silica flotation for their concentration. Ores from the Shroup and Conner-Hough properties are very similar but differ somewhat in their response to ore-dressing Method's. In all instances, the man¬ganese minerals are psilomelane and pyrolusite, with minor amounts of other manganese oxides. The country rook is a brecciated limestone; the diluent in the high-grade ore pockets is chiefly silica. The low-grade manganese ores are limestone replacements, and the chief gangue material, of course, is limestone."

Nov 1, 1947

By D. S. Kingery

This study describes five fatal accidents so unusual in occurrence that the chain of circumstances bringing them about may never be duplicated. The intent of this publication is to illustrate that everyone working underground is subjected, at all times, to definite inherent mining hazards and that safety devices, though provided, often are ineffective or not used. It is hoped that a study of these fatal accidents in bituminous-coal mines will show workers and safety engineers that nothing can be taken for granted. Safety planning with continuous study can prevent these unusual accidents as well as the routine recurring types, which cause the majority of coal-mining injuries. The treacherous, fatalistic philosophy that "it can't happen to me" or that "when my time's up I'll get it regardless of what I do," still prevails among individuals and even safety engineers. The individual or safety man who believes in luck as applied to safety should not read any further, since this study was written for the sincere, safety-minded individual who accepts the prevention of all accidents as a challenge to his knowledge, initiative, persuasiveness, and salesmanship.

Jan 1, 1954

By James W. Ballard, H. H. Schrenk

"The X-ray method of quantitative determination is advantageous because it permits determination of compounds rather -than ions or elements; for example, the direct determination of quartz in silicates,4/,5/,6/ The method also takes into account the finest particles of a sample, which may be lost in wet chemical methods because of solubility or in petrographic methods because of limitation of the microscope. The sample is usually reduced to a powder and is easily prepared,7/ only a few milligrams of material being necessary. The sample and its chemical composition are not destroyed and may be used for further analysis by X-ray diffraction or by other methods.This paper presents in detail some of the more essential problems that arise in the application of X-ray diffraction to quantitative chemical analysis, Photometric measurements are discussed in connection with line intensities and the choice of X-ray film. The internal standard method, successfully used in spectrographic analysis, is applied.Copper K-alpha X-rays from a demountable research-type X-ray tube were used with a camera of 20 centimeters radius with a cast-lead-slit collimating system. A combination of a tilted wedge and a lead-slit collimating system permitted irradiation of a large amount of sample with X-rays. This tended to minimize errors due to possible inhonogeneity of the sample, to decrease the time of exposure, and to keep the lines on the X-ray film to a minimum width. There was sufficient dispersion of the lines for satisfactory analysis of most samples. Power was furnished the tube by a. source of constant high potential consisting of a synchronous motor generator furnishing 500-cycle power to a 100-kv. transformer, rectifying valves, and a condenser filter circuit. The X-ray tube was operated as a gas-type tube at 35 kv, and 20 ma,, the exposure times varying from 1 to 2 hours. The constant output of X-rays from the tube, indicated bar an exposure meter built for the purpose, was satisfactory.The recording microphotometer8/has been described. It was found preferable to a nonrecording instrument for measuring blackening of lines above a background on X-ray films. This background, which usually occurs, is sometimes complicated by numerous peaks from lines of complex diffraction patterns. is microphotometer record of the pattern, therefore, facilitates the location of the background 'and the measurement of the heights of the peaks and thus contributes to the accuracy of a determination."

Jun 1, 1946

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

A complete list of permissible mining equipment, rescue apparatus and gas masks tested. Prior to Jan. 1, 1929, w s published in Bureau of mines Information Circular 60972. The present list includes practically all equipment tested and. approved by the Bureau, up to and including July 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists,, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage battery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal showing hat it has been "approved" by the Bureau. These tests are designs to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Jan 1, 1929

By R D. Fleming

A single-cylinder research engine was operated on pure hydrocarbons and simple (two-component) mixtures of pure hydrocarbons to study the effect of fuel composition on exhaust emissions from a spark-ignition engine. Used as fuels were three pure hydrocarbons that represented the primary hydrocarbon types present in commercial motor fuels: A paraffin (2,2,4-trimethylpentane), an olefin (2,4,4-trimethylpentene-2), and an aromatic (meta-xylene). The engine was operated at the same equivalence ratio for all of the fuels used in the experiment. Exhaust gas samples were collected and quantitatively analyzed for carbon monoxide, carbon dioxide, hydrogen, nitrogen oxides, aldehydes, and hydrocarbons. Exhaust hydrocarbons were separated and quantitatively measured with a chromatographic system employing a flame-ionization detector. Unknown hydrocarbons and oxygenated materials in the exhaust were identified with a Time-of-Flight mass spectrometer coupled to a chromatographic system. The results of the exhaust gas analyses showed that ethylbenzene, l-methyl-3-ethylbenzene, and l-methyl-3-vinylbenzene were more abundant in the exhausts from either 2,2,4-trimethylpentane--m-xylene or 2,4,4-trimethylpentene-2--m-xylene fuel mixtures than in exhaust produced from m-xylene. Also, the pure 2,4,4-trimethylpentene-2 fuel produced smaller amounts of C2 to C7 olefins in the exhaust than that produced by the pure 2,2,4-trimethylpentane fuel. The exhaust from pure m-xylene fuel contained aromatic hydrocarbons of higher molecular weight than the parent fuel. The amount of total hydrocarbon (moles of exhaust hydrocarbon per mole of fuel used) in the exhaust from the three pure fuels decreased in the following order: 2,2,4-trimethylpentane > 2,4,4-trimethylpentene-2 > m-xylene. The hydrocarbon mole-fractions of unreacted fuel in the exhausts produced from each of the pure fuels were 0.20 for 2,2,4-trimethylpentane, 0.13 for 2,4,4-trimethylpentene-2, and 0.66 for m-xylene.

Jan 1, 1970