Search Documents

By K. J. Miller

A two-stage froth flotation technique was developed in the laboratory to separate fine-size pyrite from coal. The process consists of the initial flotation of a 15-percent solids coal slurry with a minimum of frother; the coarse, free pyrite and other refuse are removed in the tailings. The froth product from this first stage is then repulped and treated with a coal depressant, a pyrite promoter, and a frother to float the remaining fine-size pyrite or pyrite attached to coal particles. With the two-stage process, the pyritic sulfur content of a Lower Freeport bed coal sample was reduced from 1.78 percent to 0.75 percent in the first stage, and from 0.75 percent to 0.27 percent in the second stage with good clean coal recovery.

Jan 1, 1972

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By R. D. Van Zant

The method for smelting zinc in horizontal retorts developed several centuries ago is still in use. This process consists essentially of the reduction of zinc oxide by carbon at 1,200° to 1,400° C. in a fire-clay retort. The reaction is highly endothermic, and a high radiation loss occurs in transferring the heat of reaction through the fire-clay walls. In recent years, silicon carbide retorts with much better heat-transfer characteristics than fire clay have been supplanting the old retorts. The practical impossibility of recovering the carbon monoxide formed in the reduction causes a large loss of fuel. Intermittent smelting is done in small retorts that are manually charged and discharged, and the furnace crews must be specially trained if efficient results are to be obtained. During the past 20 years several processes have been introduced that have substantially improved the horizontal-retort process. One of these, developed by the New Jersey Zinc Co., consists of a continuous process in which a briquetted mixture of zinc sinter, reducing agent, and binder is coked at 750° to 900° C. and charged into a vertical silicon carbide retort. A supply of displacement air or exhaust combustion gas is introduced at the base of the retort at an appropriate pressure in order to keep the zinc vapor from condensing on the cooled residue in the lower part of the retort. Any .oxidizing constituents in the displacement gas are converted to carbon monoxide by reaction with the carbon in the charge. The spent residue is continuously removed at the bottom of tl1e retort. The chief advantages of this process are said to be increased output per man-day, improved working conditions, high recovery of zinc, increased thermal efficiency, and long retort life.

Jan 1, 1950

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By H. H. Schrenk

There are several well-recognized procedures for controlling exposure to hazardous atmospheres in industry. They include (a) substitution of less toxic material, (b) enclosure of processes, (c) wet methods, (d) local exhaust, (e) general ventilation, and (f) use of respiratory protective devices. In addition to their employment as a control measure in occupational exposures, respiratory protective devices also are essential in emergencies that may arise from failure or improper use of other control equipment. Respiratory protective devices usually are employed to supplement other methods of control, as temporary expedients, or when other methods are not readily applicable or practicable. It seems reasonable to assume, however, that where respirators are used consideration has been given to the factors involved and that the devices can provide satisfactory protection if used properly. Their use should not be arrived at simply by a process of elimination of other methods that are more difficult to apply.

Jan 1, 1943

By Heine Kenworthy

In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral. Content of this ore was considerably higher than in the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently tailing losses, especially with respect to lead, were high. A. few years later, in order to study the possibilities, of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Station for testing. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values were present.

Jan 1, 1948

By W. H. Eddy

The Bureau of Mines made small-scale continuous tests and large-scale commercial plant tests of a calcareous fluorspar ore near Cave-In-Rock, Ill., to determine if the application of the lignin-fluoride process of fluorspar flotation would be industrially feasible for treatment of fluorspar ores, and also to compare the lignin-fluoride process with the quebracho process, which is the method currently used for concentrating calcareous fluorspar ores. The small-scale continuous tests yielded fluorspar concentrates analyzing 93.6 percent CaF2 with a recovery of 87.6 percent of the total fluorspar in the ore. In large-scale commercial plant tests, a fluorspar concentrate analyzing 93.3 percent CaF2 with a recovery of 78.0 percent was produced by the quebracho method. About 86.0 percent of the fluorspar was recovered in a metallurgical-grade fluorspar concentrate from the lignin-fluoride circuit which analyzed 89.9 percent CaF2? with a much simpler flowsheet than that in the current commercial application.

Jan 1, 1967

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By C. M. Frost

The hydrodesulfurization characteristics of a residual fuel prepared from Wilmington, Calif., crude oil were determined at temperatures from 600° to 900° F, pressures of 200 to 800 pSig, and space velocities from 0.2 to 2.0 Vo/Vc/hr, using cobalt molybdate type catalysts. A prediction equation, developed from the experimental data, satisfactorily predicts the fraction of total sulfur that can be removed under any combination of operating conditions within the ranges investigated. Yields and properties of the low sulfur product are correlated with the fraction of total sulfur removed. Kinetic calculations show that the apparent reaction order and activation energy change with space velocity and temperature.

Jan 1, 1970

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By James V. Kelly

During the winter of 1946 and the spring of 1947, the Bureau of Mines conducted an investigation and drilling program in the vicinity of the village of Fairplay, Wis. Fifteen diamond drill holes totaling 2,457.6 feet of bore were completed. This work was part of a general study of the zinc-producing area of southwestern Wisconsin and had the particular purpose of investigating a structural trend, determined by the Federal Geological Survey, in an area some distance from known ore bodies or active mines.

Jan 1, 1948

By Michael Gibbons

A method of monitoring roof stability in underground mines by detecting the changes in resistivity of roof material was tested. The device built by the USBM was tested over a 16 month period at the White Pine Copper Mine in White Pine, Michigan. Three falls of ground were monitored by means of as many as 11 sensors. Data indicate a correlation between changes in resistivity and impending structural failure. Problems were encountered with the high roof electrode impedance in the winter and spring due to the drying out of the roof material. Difficulties also developed in obtaining a permanent bond between the roof rock, the conductive epoxy and the electrode plate. Some data were lost due to timer and fuse problems within the unit. These were eventually rectified.

Jan 1, 1979

By P. M. Brown

The Bureau of Mines is investigating a dewatering technique for coal-clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong stable flocs that can be dewatered on a static screen. A field test unit (FTU) using this technique was operated at approximately 400 gal/min, using a waste stream from the flotation circuit of a coal preparation plant. Consolidated coal-clay material con-taining 55 to 60 pct solids was produced when the flotation circuit slurries of 2.7 to 8 pct solids were treated with 0.1 to 0.3 Ib PEO per ton of solids. The FTU was also operated at 64.5 and 87.5 gal/min using a portion of the underflow slurry from the preparation plant's thickener. Consolidated coal-clay material containing 55 to 60 pct solids was produced when the thickener underflow slurries of 19 to 24 pct solids were treated with 0.08 to 0.2 Ib PEO per ton of solids. PED-treated materials continued to dewater when placed in a pit.

Jan 1, 1983

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements provide evidence for the formation of Cr(V) intermediates in the enzymatic reduction of Cr(VI) by glutathione reductase (GSSG-R) in the presence of NADPH, indicating an initial single-electron transfer step in the reduction mechanism. Depending on the pH, at least two different Cr(V) species are generated which are relatively long-lived. In addition, we have detected the hydroxyl (·OH) radical formation during the GSSG-R catalyzed reduction of Cr(VI) by spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) and a-(4-pyridyl-1-oxide)-N-tert-butylnitrone (4-POBN) as spin traps. Superoxide dismutase (SOD) causes only a minor effect on the ·OH radical and Cr(V) formation, indicating that the ~ - is not significantly involved in the reaction mechanism. Catalase enhances the Cr(V) formation and substantially inhibits the ·OH radical formation, indicating the involvement of hydrogen peroxide (H20 2) in the reaction mechanism. Addition of H20i suppresses Cr(V) and enhances the ·OH radical fonnation. Measurements involving N-ethylmaleimide show that the Cr(V) species, produced enzymatically by the reduction of Cr(VI) by GSSG-R, react with H2O2 to generate ·OH radicals, which might participate in the initiation of Cr(VI) carcinogenicity.INTRODUCTIONC(VI) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals [1-4) and to cause mutations in bacteria and transformation of mammalian cells [5-8). In contrast, most Cr(lll) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic [9, 10]. Cr(VI) and Cr(lll) oxidation states are different in their metabolic pathways: Cr(VI) ions are rapidly transported across cellular membranes [2, 11-13), while Cr(lll) moieties do not easily penetrate cells and are not oxidized by cellular constituents [3]. Since it is known that the reduction of Cr(Vl) is required for its reaction with DNA [2], the molecular mechanisms for the intracellular Cr(VI) reduction have been the focus of studies during the past decade but the details are still not understood."

Jan 1, 1990

By R. W. Stahl

"This study by the Federal Bureau of Mines was confined to pillaring with continuous mining machines and to mines where total extraction is practiced. Many different conditions and practices in as many coalbeds as possible in Pennsylvania were observed.Pillar extraction or pillaring can be the most productive part of coal mining if done properly; but it also can be the most dangerous if done improperly.Because of the need for more careful planning before and caution during pillaring, many mining companies resort to the undesirable practice of stumping or hogging of pillars with subsequent unnecessary waste of valuable natural resources. Pillaring can be done at reasonable cost and safely, as proven at many mines where complete extraction is practiced and enviable cost and accident records are maintained.Although continuous mining machines are bulky and sometimes difficult to maneuver, they have been used with great success in pillaring. Occasionally, however, a machine is caught, or men are injured by a fall during pillar recovery. This Bureau survey was conducted to ascertain how safe and successful pillaring (especially the removal of final stumps in lifts or the final stump of a pillar), is accomplished in some mines, while others have considerable difficulty under similar conditions.The Bureau hopes the information to be presented in this publication will prove beneficial to those who wish to recover more pillar coal and to improve their accident record during such procedures."

Dec 1, 1959

By A. J. Kraemer

[During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attach bearings, wrist pins, and other parts of engines. On the other hand, in making gas¬oline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more then 90 per cent of the 153 samples analyzed passed the Federal specification requirement, which limits the sulphur content to 0.10 -nor cent. 3 This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity and distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same' as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995.]

Jan 1, 1930

By G. W. Birge

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Westmoreland County for coking tests was based, in part, on estimates of the coal reserves by Dowd,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in thousands of tons, as follows: [ ]

Jan 1, 1957

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Japan has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . It is based on the law and regulations of 1905 as revised in December , 1915 , and translated by J. de Becker , LL.B. Occasional words and phrases quoted herein are accordingly taken from this translation and have not been checked against the original . The references are to the law ( as distinguished from the regulations ) unless otherwise stated .

Jul 1, 1930