Search Documents

By Robert C. Ellman

The Bureau of Mines investigated the factors that cause agglomeration of lignite by freezing during winter shipment and sought methods to avoid it. Tests showed that lignite may be freezeproofed by removal of the relatively small quantity of moisture involved in forming the frost crystals which cement particles together, or by controlling the crystal characteristics. Adding dried lignite fines proved to be an effective and superior freezeproofing method. Commercial adoption of this method has been successful.

Jan 1, 1965

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By Lucien Eaton

The mining methods described in this paper are those used in a large mine producing hard specular ore on the Marquette Range in the Upper Peninsula of Michigan. Although the conditions of mining are unique in this district, they are similar to those in many other districts, and information in regard to the methods used and the results obtained should be of interest. The methods now used are an outgrowth of those of former years which have been adapted to conform with improvements in mechanical appliances, changes in the wage scale and labor supply, and the' selling price of the product. The mine is situated' at Ishpeming, in the Upper Peninsula of Michigan, 16 miles west of Marquette, its shipping port on Lake Superior.

Jan 1, 1929

By Robert D. Ewing

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, and axisymmetric and plane joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1976

By A. U. Christensen

THERMODYNAMIC data for many of the common interoxidic compounds are seriously lacking, and appraisal of possible ceramic or metallurgical applications depends upon dubious estimates. In particular, high-temperature heat-content estimates may be invalid because of unknown phase-transformations. This paper reports experimental heat-content values above 298.15° K. for five interoxidic compounds-the aluminates of lithium and sodium (LiAlO2 and NaAlO2), the ferrites of lithium and sodium (LiFeO2 and NaFeO2), and lithium titanate (Li2TiO3), as obtained by the Bureau of Mines. Sodium aluminate, sodium ferrite, and lithium titanate were found to have previously unknown transformations in the crystalline state. The heats and temperatures of these transformations were evaluated as were also the heats and temperatures of fusion of sodium ferrite and lithium titanate. The heat-content results are assembled in both tabular and algebraic-equation form for use in conducting thermodynamic calculations at temperatures in the range 298°-2,000° K.

Jan 1, 1960

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By G. L. Oldright

The data presented in this paper were collected et the smelter of the Consolidated Mining A Smelting Co. of Canada, Limited, Trail (Tadanac), British Columbia, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent, George Murray, assistant smelter superintendent; and the staff members listed in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth4 dealing with blast-furnace gases.

Jan 1, 1934

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

By Joseph J. Wallace

1. The investigation shows that there are two coal beds of major importance in Perry County from the standpoint of present production -Flag and Fire Clay -and two beds of minor importance -Haddix and Hindman. The Flag and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 840 million short tons as of January 1, 1954. Of this total, 720 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1954

By Milton B. Hall

This report discusses in detail laboratory and pilot-plant tests conducted from January 1951 until January 1955 at the Northwest Electrodevelopment Experiment Station of the Bureau of Mines, Albany, Oreg., on defluorination and recovery of evolved fluorine from phosphate rock. Results of use tests of defluorinated phosphate rock by cooperating agricultural colleges and the United States Department of Agriculture are also included. In 1954 the consumption of fluorspar, the only domestic fluorine-bearing mineral of commercial importance, was approximately 478,000 short tons; 245,000 tons was from domestic mines. The production of marketable phosphate rock in the same period was about 13,800,000 long tons. Of this total amount, approximately 15 percent was produced in the West. From the viewpoint of conservation and utilization of fluorine as a natural resource, it is interesting to note that the total estimated quantity of fluorine in domestically produced phosphate rock is more than double that present in domestically mined fluorspar.

Jan 1, 1958

By Jay W. Hawkins

Under an approved remining program, mine operators can remine abandoned coal mines without assuming legal responsibility for treatment of the previously degraded water, as long as the discharging waters are not further degraded and other regulatory requirements are satisfied. A U.S. Bureau of Mines review of 105 remining permits in Pennsylvania indicates that remining results in substantial reclamation of abandoned mine lands, utilization of significant quantities of coal, and reduction of contaminant loads (acidity and iron) from degraded mine drainage discharges. Normality tests performed on the water quality and flow data indicate generally nonnormal distributions and extreme right-skewness, tending toward lower values. The water quality of underground coal mines was observed to be more highly degraded in terms of acidity, iron, and sulfate than that of surface coal mines. The optimum baseline sampling scenario is 12 months in duration at a frequency of one sample per month. Analysis of water quality and flow rates before and after remining indicates that a majority of the mines exhibited either no change or a significant decrease in pollution rate because of remining. The discharge flow rate was the dominant controlling factor when the post-remining contaminant load was significantly better or worse than the baseline (pre-remining) load.

Jan 1, 2010

7133. Clewell, D. H. The Gravimeter. Prec. and Trans. Texas Acad. Science 1941, Austin, Tex., vol. 25, 1942, pp. 86-88. Static gravimeters, unastatized and. astatized, are considered to be the most practical for oil exploration. One gravimeter is described using a beam whose moment about a pivotal axis is elastically balanced. Magnetic or electric fields are deemed unsatisfactory for balancing gravitational force because they cannot easily be kept constant. The gravimeter described is capable of detecting a change in altitude of 3 inches and a change in latitude of about 150 feet. V. S.

Jan 1, 1944

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By P. D. Laverty

This report describes a processing method developed by the U.S. Bureau of Mines to produce high-quality flake graphite from the steelmaking waste known as kish. The kish produced by current steelmaking practices is a mixture of graphite, desulfurization slag, and iron that is skimmed from the molten iron feed to the basic oxygen furnace. It is estimated that the graphite content of kish discarded by U.S. steel plants is more than sufficient to meet the total U.S. demand for flake graphite. That need is now filled by natural graphite from foreign sources. Kish was treated by a combination of screening and hydraulic classification to produce a concentrate containing greater than 70 pct graphite. Leaching of the concentrate with hydrochloric acid solution gave a graphite product with 95-pct purity. An optional secondary leaching operation with hydrofluoric acid produced graphite with a purity of 98 pet or greater. The flake size of graphite from kish ranged from 10 mesh down. Evaluation of test samples by industrial graphite users indicated that kish graphite is a suitable substitute for the natural material for most uses. A process flowsheet and material balance for pilot plant design are presented.

Jan 1, 2010

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By K. Hennings

Noise from vibrating screens is generated in two ways: 1) Noise due to the material being processed and, 2) noise from the screen itself. Non-metallic decks had been shown previously to reduce material noise. The noise reduction and change in screening performance was quantified for six non-metallic decks using dolomite, granite and coal as the materials. The non-metallic decks were from 2 to 7 dBA quieter and from -1 to +10 percent less efficient as compared to a steel wire cloth deck of the same open area. Damping of the sidewalls and isolation of the drive mechanisms had been shown, in a development configuration, to reduce the noise of the screen itself. Tests of four prototype damping treatments gave reductions up to 4.9 dBA and the mechanism isolators gave an additional 2.1 dBA. The treatments were successfully life tested in two ways: 1) Lab tests to a simulated 25,000 hours were conducted on samples of the treatments in a corrosive salt spray to simulate coal plant wash water and, 2) the full size treatments were run on a full size screen for 5,000 hours.

Jan 1, 1980