Search Documents

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been published.4/

Jan 1, 1938

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX'S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By Frederick K. Allgaier

This report presents the final data from a 5-yr Bureau of Mines study designed to determine the surface subsidence characteristics resulting from longwall coal mining in a geologic environment common to the Western United States, It includes a description of the geologic setting of the study site, the mine plan, measurement techniques, and results of the monitoring program. Measured subsidence values were obtained over four adjacent longwall panels- Major subsidence characteristics such as longitudinal and transverse profiles, angles of draw, time-related subsidence development, and critical width are discussed. The maxima subsidence value of 5.8 ft was 68 pct of the mining thickness. The average angle of draw was 30°, Subsidence at the center of the first panel continued for 46 months following undermining. The lengths of the longwall panels precluded a definitive determination of the critical width and maximum possible subsidence.

Jan 1, 1988

By Martin Hertzberg

This Bureau of Mines report analyzes diverse observations of the rates and mechanisms for the pyrolysis and devolatilization of coal and polymethylmethacrylate (PMMA). New data are presented for PMMA, together with new morphological evidence for the microscopic structure of the pyrolysis and devolatilization wave front in coals. It is concluded that there is no substantive evidence to support the traditional viewpoint that the pyrolysis and devolatilization rate process occurs isothermally, under chemical rate control; or is described realistically by a classical, unimolecular Arrhenius function of temperature. Instead, the reaction process occurs as a highly nonisothermal, heat-flux-driven, pyrolysis and devolatilization wave front, whose speed of propagation is predictable by internal heat transport constraints. Except for the complication of its charlayer residue, whose increasing thickness insulates the pyrolysis wave front from the heat source flux that drives it, both coal and PMMA behave similarly during pyrolysis and devolatilization. For PMMA, decomposition occurs at a temperature of 3500 to 5500 C; for coal it occurs at 4500 to 6000 C. There is no evidence that the reactant temperature ever exceeds those values regardless of the source temperature to which the samples are exposed.

Jan 1, 1988

By J. T. Dunham

Zirconium has possible use in industry where severe corrosion conditions are encountered because it resists attack from a variety of corrosive environments. However, very little experimental testing has been done to evaluate the corrosion behavior of zirconium when simultaneously subjected to high tensile stresses and exposed to corrosive environments. This investigation was initiated for an evaluation test, but was limited to environments consisting of ferric chloride solutions which were known to attack zirconium and were shown to promote stress-corrosion cracking in preliminary tests. Tests for cracking susceptibility were conducted by the Bureau of Mines to show the effect of stress, solution concentration, air aeration of solution, and the method of mechanical processing. Tensile stress was applied to the specimens by a constant-load method which proved more reliable than a constant-strain method.

Jan 1, 1961

By A. E. Petersen

To reduce U.S. dependence on imports of titanium, the U.S. Bureau of Mines has investigated the recovery of titanium from perovskite (CaTi03). Domestic perovskite deposits represent a significant, but untapped, titanium resource. An acid sulfation method was developed that will extract about 97 pct of the titanium and the columbium and 70 to 90 pct of the rare-earth byproducts from perovskite concentrates. A flow-sheet for recovering titanium as pigment-grade titanium dioxide (Ti02) is discussed. Test work performed in developing each unit operation is described. The first three unit operations have been demonstrated using laboratory-scale continuous methods of operation: acid sulfation of perovskite concentrates, leaching sulfation residue to dissolve metal values, and precipitation of titanium oxysulfate monohydrate (TiOS04?HP) from the resulting leach flltrate. Batch testing of other unit operations was performed: TiOS04?H20 redissolution and iron reduction, precipitation of Ti02 by hydrolysis, and regenerating recoverable acid with rare-earth byproduct recovery. Cost evaluation results are provided, indicating that processing perovskite concentrates by acid sulfation may be an economically viable means of producing Ti02.

Jan 1, 2010

By Michael T. Nigbor

This Bureau of Mines publication identifies the significant environmental issues associated with the potential development of strategic and critical minerals in the Stillwater Complex, MT. The Stillwater Complex contains deposits of Cr, platinum-group metals (PGM), and Ni. Issues that must be addressed prior to minerals development include the effects mining, milling, and smelting will have on the land, water, and air, and methods of minimizing the environmental impacts.

Jan 1, 1985

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964

By James H. Russell

Alkalized alumina (an active form of sodium aluminate) has been considered as a sorbent for the removal of sulfur dioxide from industrial flue gases. Four rate equations, each based on a different mechanism, were compared with the results of thin-bed sorption tests. It was found that each equation agreed with the experimental results, within experimental variance, over most of the range of sorption studied. First-order rate equations were generally satisfactory in explaining both sorption and regeneration. It is concluded that the equations developed are adequate for the design of commercial fluidized beds for the sorption of SO2 from industrial flue gases and regeneration of the alkalized alumina.

Jan 1, 1970

By M. G. Zabetakis

The use of liquid hydrogen as a high-energy fuel introduces numerous hazards not ordinarily associated with the use of other more conventional fuels. These hazards are attributable to the unique properties of hydrogen in the liquid and gas states (table 1). Since little work has been conducted on explosion and related hazards of cryogenic fuels, a research program was undertaken to obtain basic data on such dangers for hydrogen and other combustibles under these conditions. These data were used to outline emergency procedures for protecting personnel and equipment when an accidental spillage of liquid hydrogen occurs and to establish a quantity-distance table for the storage of this fuel. The vaporization of liquid hydrogen from a surface is treated as a prob¬lem in heat transfer theory. Two extreme cases are briefly considered: (1) The transfer of heat occurs at constant temperature drop between, the boiling liquid and the hot surface, and (2) the transfer of heat is limited by the rate at which it can flow to the surface from a hot insulating medium. The available data indicate that the former case (1) is applicable when vaporizing from a conducting surface and, initially, when vaporizing from an insulating medium; the latter case (2) is applicable after initial flash vaporization has occurred from the insulating medium. The vaporization rate determines in part the rate at which flammable hydrogen vapor-air mixtures are formed above a spill area. However, the rates at which heat is transferred to the vapor, and air is brought in contact with it also are of importance. Accordingly, the distribution of flammable mixtures above a spill area was determined experimentally. In general, flammable mixtures were found to be both above and within the visible vapor cloud.

Jan 1, 1961

By Philip C. Tully

These modifications to the Redlich-Kwong equations for pure hydrogen and neon were developed after an unsuccessful attempt to generalize a modification technique previously developed for helium. New coefficients of the B terms were developed by minimizing the residuals. No changes were made in the coefficients of the A terms. For normal hydrogen, B was changed to [0.08063Tc PcT] for temperatures from 980 to 423° K and pressures up to 1,050 atm. The average deviation in Z was 0.36 percent with maximum deviations less than 1 percent for all but a few low-temperature points. For neon, B was changed to [PCT 0.1025T], for temperatures from 120° to 973° K and pressures up to 1,500 atm. The average deviation in Z was 0.34 percent with maximum deviations less than 1 percent for all but a few high-pressure and low-temperature points. Efforts to attain a lower temperature range to comparable accuracy with this type of modification were unsuccessful. In the range of applicability, these equations should be used with caution when calculating derived thermodynamic functions, such as the isobaric specific heat.

Jan 1, 1968

By Koehler Stout

Previous work done by the authors of this report indicates that hydraulically-placed backfill can be strengthened several fold by various placement methods. Sunshine mill tailings were tested by these placement methods and strength increases up to thirty times were achieved over the ordinary placement methods. A computer simulation study of the test stope in the Sunshine Mine showed that a high-modulus fill absorbs up to 27% of normal stresses versus 7% for "normal" fill while reducing maximum convergence 28% versus 8% for "normal" fill. Although high-modulus fill was not placed in the test stope during this contract, various instrumentation was purchased, designed and built to record necessary data in the stope. Stress gauges were placed in the pillars and recorded data corresponded quite closely with theoretical projections.

Jan 1, 1983

To develop effective noise controls for continuous min-ing machines (CMMs) to reduce worker noise exposure. Background Noise-induced hearing loss (NIHL) is an occupational illness caused by chronic exposure to excessive sound levels. For underground coal mine workers, NIHL continues to be a serious health issue. Analysis of hearing loss data suggests that by retirement age, 70%?90% of U.S. coal mine workers will have a hearing impairment. Operated in the confined spaces of underground mines, large industrial mining equipment often produces sound levels that can be harmful to workers. Of all equipment used in underground coal mining operations, CMMs account for the most noise overexposures. To reduce the occurrence of noise over-exposures, engineering noise controls must be developed for the CMM.

Sep 1, 2008

By J. L. Kohler

The final report for Phase II of Bureau of Hines Contract J0134025 concerns the research and development of sensitive ground-fault relays for dc utilization systems in mining. Sensitive relaying employs very low pickup levels such that, when used in conjunction with very high resistance grounding, the exposure of a human to ventricular fibrillation is significantly reduced. To delineate the desired relay characteristics, the report begins by reviewing previous research in this area. A theory for the saturable transformer used to sense the fault current is presented. The design of the ground fault relay is described in sufficient detail that it may be duplicated. Test procedures and results are given. Finally, conclusions and recommendations related to Phase II are presented.

Jan 1, 1986

By E. P. Carman

This report is the 19th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations. The first 17 reports covered fiscal years; however, the 18th report3/ covered the 18 months from July 1, 1952, to December 31, 1953, to permit the publication of this and subsequent reports on a calendar-year basis. Most of the material in this report relates to publications by Bureau authors issued during the reporting period. Some work is referred to on which the results have not yet been published or may not be published for security or other reasons. In a few instances publications are mentioned that were issued before the reporting period but were not included in previous reports. Further details on the published work described herein may be found in the publications cited in the footnotes. Research and technologic work on coal by the Bureau is directed toward developing and encouraging increased conservation of coal resources through safer and more efficient mining, preparation, and utilization. Significant advances were made during the year in these fields, particularly in coal-mine safety and in preparation and utilization of the various ranks of coals.

Jan 1, 1956

By B. H. Eccleston, R. F. Kendall, D. E. Hirsch, Norman G. Foster

The mass spectra of 23 alkylthiophenes are presented , including 21 that have not been previously reported . Correlations between mass spectra and the structure of the thiophene homologs are discussed . Comparisons with , and corroboration of , earlier workers ' correlations and predictions are made . Several additional correlations are reported to enable the spectroscopist to identify the substituents on alkyl - substituted thiophenes , and the relationship of the mono - substituted and 2,5 - disubstituted alkylthiophenes is discussed in detail .

Jan 1, 1964

By Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 1, 1981