Search Documents

By Madan M. Singh

Hydraulic mining has been practiced in the United States since 1852 and many mineral commodities, such as gilsonite, phosphates, lead-zinc, silver ores and St. Peter Sandstone can be mined in this manner. In 1958, the U. S. Bureau of Mines initiated research into the mining of coal using these techniques.1-4 These early investigations were conducted in the 5000 psi pressure range. The large nozzle diameters used in this pressure range produced extremely high flow rates which created visibility problems at the coal face, and required removal of large amounts of water from the mining area. Besides, the production rates were not much better than with mechanical methods. This indicated that with higher pressures the water quantities might be reduced using the same or higher horsepowers but enhanced breakage. For this reason intensive investigation in material removal using fine water jets at extremely high pressures (50,000 psi to 100,000 psi) has been undertaken. This was not the entire reason for this contract from the Bureau of Mines, however. The contract objective is outlined later. IIT Research Institute has done pioneering work in high pressure jet development in the United States.5-8 Similar schemes have been investigated abroad. 9-13 Hydraulic mining of coal at relatively low pressures is successfully being done in the Soviet Union, Japan, Canada, and most recently, in Germany.

Jan 1, 1973

By Lloyd A. Morley

This seven-chapter document is the first volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. After a short introductory chapter, Chapter 2 discusses the history of electrical use in mining and introduces "typical" mine- power-system arrangements. Chapter 3, 4, and 5 supply basic information on electrical theory, circuit analysis, and motors. Next, the Grounding and Distribution Chapters detail unique aspects of mine power systems. Elements of surface and underground use are included in all these chapters. An index concludes Volume I and is cross-referenced to both report volumes.

Jan 1, 1982

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By J. E. Hamak

This publication contains analyses and related source data for 266 natural gas samples from 20 States and 2 foreign countries. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of the U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1992

By R. Hogg, Y. Lee, D. E. Rannels

"Lee, Yu-Chen, Richard Hogg, and D. Eugene Rannels. Extracellular matrix synthesis by coal dust-exposed type II epithelial cells. Am. J. Physiol. 267 (Lung Cell. Mol. Physiol. 11): L365–L374, 1994.—Although integrity of the alveolar basement membrane may influence progression of lung injury induced by inhaled particulates, little is known about direct effects of coal dusts on the alveolar epithelium or its extracellu¬lar matrix (ECM). Effects of dust on synthesis of cell and ECM proteins by type II cells (T2P) was thus investigated. Three coal dusts (anthracite no. 867; bituminous no. 1451 and no. 1361) and mine dust MIT-3, of respirable size, were studied as a function of dose and time over 3 days of primary T2P culture. On day 1, 750 µg/ml of 867 were required to increase relative synthesis of ECM proteins (ECM/cell). MIT-3, 1451, and 1361 were without effect. By day 3, 867 or MIT-3 increased ECM/ cell 60-100% at 300 µg/ml; 1451 produced modest, dose-dependent stimulation, whereas 1361 remained without effect. None of the dusts caused significant cytotoxicity. The results show dose- and time-dependent effects of well-characterized coal and mine dusts to modify partitioning of newly synthesized proteins into the ECM and suggest that coal dust exposure may modulate structure or function of the subepithelial basement membrane.basement membrane; cell culture; inorganic dust; lung injury; extracellular matrix deposition; pulmonary epitheliumCHRONIC EXPOSURE to coal dust may be associated with development of pulmonary fibrosis and consequent loss of normal lung function (see Ref. 26 for review). Al¬though the pathways of inorganic dust-induced lung injury are recognized to involve an inflammatory re¬sponse, the underlying pathogenic mechanisms are not understood in detail. Acute and chronic responses to dust exposure involve a variety of interacting cells of the immune system, including macrophages, T cells, and B cells, along with pulmonary fibroblasts. These responses reflect direct effects of the dust particles, as well as indirect effects mediated by soluble factors, including cytokines and eicosanoids (see Ref. 41 for review).Studies of pulmonary macrophages and fibroblasts following silica exposure suggest that dust-induced damage at the airway surface may involve cellular injury through oxidant-mediated pathways. Coal dusts and related inorganic particulates can activate the alveolar macrophage (42) to produce fibronectin (15) and cytokines, such as interleukin-1 or tumor necrosis factor (4) and/or other soluble products which act locally (29) to cause acute cellular injury and to initiate the progression of fibrotic lung damage (16). Type I epithelial cells are typically more susceptible than type II cells to oxidant injury. Type I cell damage and subsequent death leads to denudation of the subepithelial basement membrane (2, 21) and can be associated with leakage of plasma constituents from the pulmonary vasculature into the alveolar compartment (13)."

Dec 1, 1995

By Forrest T. Moyer

Quarry accidents in 1963 caused 61 fatal and 3,468 nonfatal injuries which occurred at respective frequency rates of 0.31 and 17.91 per million man-hours of worktime. The fatality record in 1963 was better than in 1962 but was appreciably worse than in 1.961. For nonfatal injuries, the 1963 record was slightly worse than in 1962 but was better than in 1961. The injury--severity rate of 2,913 days lost or charged per million man-hours in 1963 was better than that of 3,046 in 1962, the first year for which such data became available. The average severity of all injuries in 1963 was 160 days lost or charged per injury, 15 less than in 1962. An average of 91,960 men were at work on active days in 1963 and these men had an aggregate worktime of 193.7 million man-hours during the year.

Jan 1, 1972

By N. L. Wimmler

The chromite deposits along the Stillwater complex in Stillwater and Sweetgrass Counties, Mont., have at various times been studied and reported on by the Federal Geological Survey, the Montana Bureau of Mines and Geology, other Government agencies, and private interests, Several of the deposits were explored to a mall extent by the owners during the World War of 1914-17, but no production resulted. The importance of these deposits and the urgent necessity of developing large domestic sources of chromite were realized shortly before the beginning of the recent World War. These deposits were therefore investigated and developed by Government agencies and., as a result, now afford the largest known reserves of chromium in the United States. In 1939, under the authority of the Strategic Minerals Act, the Bureau of Mines and the Geological Survey made preliminary investigations of these deposits. As a result, the Bureau of Mines conducted an extensive program of trenching, diamond core drilling, and sampling. This work was begun in August 1939 and continued to April 1943. The Bureau of Mines also performed numerous metallurgical tests on the beneficiation of the chromite ores and concentrates and for the production of chromium metal there from. Research continues as a means toward utilizing these ores.

Jan 1, 1948

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that affects the net expansion of the change in both industrial and test ovens. Various test results have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; out no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors. While investigating the reactivity of cokes made by the BM-AGA method,6/ Reynolds7/ found that granular low-temperature cokes shrink considerably then reheated to higher temperatures. This shrinkage was large enough to influence the behavior of the charge (net expansion or contraction) in a coke oven to a marked extent. Since that time the Bureau of nines has investigated the shrinkage of coke different methods, all of thick had one common objective - the elimination of the effect of other factors, such as swelling in the plastic range, which could either partly or completely mask the shrinkage of the coke. Only parts of these studies have been published8/9/ in abbreviated form in]

Jan 1, 1940

By J. W. Paul

Mine foremen are employed in coal mines for two reasons: First, so that the underground work. may proceed in an orderly manner and that each employee gives attention to his duties; and second, by reason of the State law which re- quires the employment of such officials to see that the laws relating to safety are carried out. It may be seen that, with these two duties, the foreman has wide scope of authority and much responsibility. As foreman of operations he has to meet certain economic questions that contribute to the cost of producing the coal, and as the agent of the State he must also supervise and coordinate the work in such manner as to insure that the employees work under safe conditions. As the roof of coal mines is the source of the greatest hazard naturally the care of the roof must take much thought and planning on the part of the fore- man; and this circular is therefore presented to call attention to some things he may do to prevent injury to the workmen by falls of the roof material or coal. Mine foremen, in the principal coal-producing States, are certified by a State board which prescribes certain qualifications, experience, and character, attested by examination and personal endorsement. Certified foremen, therefore, are men who have had experience underground and know roof conditions and timber- ing methods. The suggestions herein are based upon observations made at many mines and collectively embrace practices that have been found to be in effect and pro- moted by experienced mine foremen:

Sep 1, 1930

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made an the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By D. A. Larson

This is the second in a series of Bureau of Mines reports which de-scribe experiments designed to devise an efficient, economic mechanical fragmentation technique for hard rock. The previous study described the development of the ripper cutting technique to successfully cut hard rock with 3-to 6-in-wide drag cutters. This study was conducted to test the ripper cutting technique at full scale using 9-in-wide drag cutters. The experiments were conducted with a special test device that cut shallow, 6-by 6-ft openings in 9,200-lbf/in2 compressive-strength concrete blocks. The tests showed that ripper cutting can excavate large-scale openings of the type required by the mining industry at a production rate that outperforms the conventional drill-blast technique. Moreover, the system can produce openings of various sizes and shapes, is simple to oper-ate and maintain, and produces very little dust or noise during operation. The system appears to meet all of the criteria for a successful hard-rock mining machine.

Jan 1, 1987

By Steven J. Page, John A. Organiscak

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grind ability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated with ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss(ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-m coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.

Jan 10, 1998

By S. C. Termes, P. E. Richardson, R. L. Wilfong

"The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly disseminated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. Post flocculation separations resulted in flocculated bornite in grades as high as 92 pct. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s). INTRODUCTIONBecause of the increasing interest in selective flocculation as a beneficiation technique for low-grade, highly disseminated ores and for selective desliming, the Bureau of Mines has been investigating the flocculation behavior of several cross-linked starch derivatives containing chelating groups. This report dis cusses the flocculation of sulfide mineral fines by insoluble cross-linked starch xanthate (ISX).Polymeric materials such as ISX, which contain a chelating group of known re¬activity towards specific mineral surfaces, were first proposed by Slater, Clark, and Kitchener (1), 3 Kitchener (2), and Attia and Kitchener (3) as selective flocculants for mineral fines with particle aggregation possible through a bridging mechanism. ISX appeared to be attractive as a sulfide mineral flocculant because (1) alkyl xanthates are known to react selectively with sulfide minerals"

Jan 1, 1983

By E. C. Lane

[The motor gasoline that s being marketed in the United States this summer slightly more volatile then that sold a year ago. This increase in volatility is shown by a general lowering ref the average distillation rang, of about 2°F. During the post 10 years the Bureau of Mines has made semiannual surveys of the gasoline marketed in the United States, the survey just completed being the twentieth in the series. The 12 cities in which samples were collected have beer chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.]

Jan 1, 1929

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon&apos;s economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country&apos;s only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon&apos;s gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon&apos;s ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985

By Neal M. Muir, Robert S. Sanford, Bruce I. Thomas

"INTRODUCTION The presence of the zinc-lead-copper deposits an the north slope of Mount Eielson, Mount McKinley National Park, Alaska, has been known for many years. The deposits were examined by J. C. Reed, a geologist of the United States Geological Survey during the summer of 1931. In the summer of 1943 the authors and Clyde Wahrhaftig, a geologist of the Geological Survey, examined the deposits.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.Particular acknowledgment is due to Heine Kenworthy, who conducted the beneficiation tests under the supervision of C. Travis Anderson; to Clyde Wahrahaftig of the Geological Survey, who completed the Geologic and topographic maps, to Grant Pearson of the National Park Service; and to O. M. Grant and Mrs. Frank McGarvoy for their assistance during the examination."

Nov 1, 1947

By L. R. Burdick, J. F. Barkley

"The agglomerating index of coal is an index based upon the nature of the coke residue left when the standard volatile-matter determination of the well-known proximate analysis is made. In this determination a small amount of coal is heated in a container to about 950° C. (1,742° F.), at which temperature the volatile matter is driven off, leaving a coke formation. The coke residues for various coals are quite different in physical structure: and, for some time past, work has been done on studies of the nature of these residues in connection with the coking of coal. In 1934 Gilmore, Connell, and Nicolls proposed use of the agglomerating index for indicating the dividing line between noncaking coals and those having weakly caking properties. 4/ Its use was adopted in the standard classification of coals by rank as a requisite physical property index to differentiate semianthracite from low-volatile bituminous coal and also high-volatile ""C"" bituminous from subbituminous ""A"" coal, as shown in table 1, the standard coal classification adopted by the American Society for Testing Materials and the American Standards Association. 5./In studying the agglomerating properties of coals based on the coke residue the Bureau of Mines has adopted the notation given in table 2. Coals that in the volatile-matter determination give a coke residue either in the form of an agglomerate button that will support a 500-gram weight without pulverizing or a button that shows swelling or cell structure are considered to be agglomerating."

Nov 1, 1938

By Richard W. Lusignea

This report describes a program to evaluate the feasibility of determining roof features which occur in United States coal mines from changes in bolting machine drilling parameters. The ultimate purpose of this effort is the development of an instrumented roof bolting machine which can detect hazardous roof conditions and/or indicate when the existing roof control plan is inadequate. A survey of hazardous conditions occurring in United States coal mines is included, along with the slang expressions for these conditions, and their relative degree of hazard. Specific machine parameters are identified for detecting the specific roof conditions. Measurement concepts are proposed using readily available instrumentation in most cases. Various systems are evaluated and tradeoffs presented. An implementation plan is proposed for developing a prototype system and using it in an operating coal mine.

Jan 1, 1978