Search Documents

By Ken Schei, Martin Reed, Samuel Bowser, John Wright

From October 18 through October 21, 2001, United States Antarctic Program blasters opened ten access holes for research divers in 11-ft. thick sea ice at Explorers Cove, McMurdo Sound, Antarctica. During this project, a blasting seismograph with a hydrophone accessory was used to monitor the underwater shock waves associated with the blasting technique. Shock wave values averaged 42.3 psi for initial (cratering) shots and 5.9 for subsequent clearing shots, indicating that the ice absorbs most of the shock wave. The results also provide data for refining safety protocols for divers and for the protection of marine biota.

Jan 1, 2003

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By D. S. Preece, S. Silling, A. Bhuiyan, C. M. Lownds

GEM (Geologic Element Motion) is a Discrete Element Method (DEM) capability for blast-induced heave simulation with a very fast computational algorithm that can efficiently treat many different element shapes by utilizing alternating arcs and lines. GEM calculates rock motion from a knowledge of the gas pressure moving the elements. This requires an expression for the pressure vs volume, or the adiabat, of the explosion product gases. This work uses an analytical expression for the adiabat derived from the explosive’s properties. The effect of the explosive detonation pressure in crushing an annulus of rock, and setting up a shock wave, is termed Brisance. GEM incorporates a working hypothesis for the deleterious effect of Brisance on subsequent rock motion.

Jan 1, 2024

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Michael Milstein

Northwest Research Station said as more and more older dams are removed to benefit fish, it’s become clearer that rivers rework themselves quickly.“Where the dam is relatively small, it’s a quick response,” he said. “The river quickly forgets.”

Jan 1, 2010

By Laurent Airaud

For around ten years, electronic detonators are available for those who want to use advanced methods and to apply theories promoted by engineers and professors to reduce blast concerns or improve fragmentation and dilution. Furthermore, decision makers can verify the use of electronic detonators to drive down mining costs. Engineers and more specifically blasters are the actual users and have to be convinced of the easiness of electronic detonators. This paper deals with electronic detonators and the notion of easiness. Common feelings about the notion of easiness are discussed. Then, examples of new technologies like, automobile, photography or Information Technology are discussed to observe how they progressed throughout time with new features and sales volume. For the specific explosive initiation industry, each step of the life of an electronic detonator is dealt with concerning the easiness and a table is used to quantify this notion.

Jan 1, 2004

By J. P. Remi Proulx, Areli Rodriguez, Ruilin Yang

Historically, presplitting has been considered effective in reducing the impact of blast vibrations on highwalls. However, it remains a debated topic: how significantly can it protect highwalls, and is it worth the cost and effort to implement presplit blasting techniques? In hard rock, presplit blasting can leave half-barrels on the highwalls, clearly demonstrating its usefulness. However, in a fractured rock mass, the half-barrels from presplit blasting may not appear in most cases, leading to questions about its role in protecting highwalls. Previous studies in the literature used geophones to measure blast vibrations at far distances and could not ascertain the significant benefit of presplit blasting in reducing the impact of blast vibrations on highwalls. Additionally, no studies in the literature address the role of presplitting in alleviating blasting-released gas pressure that could penetrate joints and open new fractures in highwalls. Yang & Proulx (2019) and Yang et al. (2022) using near-field blast vibration monitoring of signature hole blasts have revealed that the peak particle velocity (PPV) of blast vibrations at a scaled distance of 1 m/kg^0.5 can be reduced by 50% or more for presplit-filtered vibrations. These results have been confirmed for both hard rock and fractured ground. In addition to summarizing the reduction in blast vibrations due to presplitting for both hard rock and a fractured rock mass, this paper demonstrates the relief of subsequent blasting gases after the detonation of blastholes. This is shown through video recordings of gas ejections from a row of empty previously fired presplit blastholes located 6 to 9 meters away from the detonation edge or final buffer row of a blasthole pattern. The results clearly show that presplitting not only lowers blast vibration PPV’s but also reduces the entry of the gases produced by the detonation process into rock fractures and or open joints.

Jan 21, 2025

By Adrian J. Moore, Alan B. Richards

Responsible blasting requires that rock throw be controlled to ensure that no danger will result to people and property. This paper describes the development and testing of empirical field calibrated formulae that can be used to evaluate rock throw, provide an early warning of when reduced burden will endanger people and property, and prevent flyrock incidents. Inputs to the formulae are charge mass, burden or stemming height, and a site constant that lies within a general range that can be tightened by site calibration. The output is the distance that rock will be thrown, and this ‘design your own flyrock’ quantification can be used to establish both safe clearance distances, and the critical range of burdens and stemming heights where the situation changes rapidly from safe to hazardous. Examples are given of the use of the model to control flyrock in open-pit mining and quarry operations, in situations which are controlled by both burden and stemming height.

Jan 1, 2004

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By Robert Hopler

A detonator is a copper tube about a quarter of an inch in diameter and an inch and a half long, closed at one end and containing in the closed end a small charge of fulminate of mercury, which has been found to be the best explosive for detonating dynamite. The fulminate charge is a very powerful explosive very sensitive to friction, lows or heat and very poisonous. When exploded it has an intense local action, shattering things in its immediate vicinity, but not extending very far away from the explosion. This kind of detonator is intended to be exploded by a spark from burning fuse.

Jan 1, 2014

By Jason Baird, Braden Lusk, Dominique Nolan, Allen Stults

Conical shaped charges have been used to penetrate rock for many years now. Examinations have been made looking at shaped charge liner geometry, material, and standoff, as well as explosive composition, confinement and initiation. Most of the testing conducted towards penetration rather than cratering has fallen within the realm of the petroleum industry and as such been confined to specific rock types, with test apparatus that include simulated down hole (subterranean) environments. The testing conducted within this experimentation is conducted at ground level, in small scale samples, using a single standoff, against multiple rock types. The data collected from that testing is examined here and relationships between physical properties of the rock and the liner are analyzed. The analysis of that data raises the possibility of a relationship that may lead to new empirical methods of penetration prediction in rock.

Jan 1, 2012

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By M. Gonçalves Peixoto da Silva, E. Rodrigo Carvalho Souza Siqueira

Mining in narrow veins is commonly applied for precious metals, generally carried out to extract gold in underground mines, due to the ore occurrence on narrow veins, mainly up to 2-meter large. The current work presents the implementation of the methodology in a zinc mine located in the state of Minas Gerais in Brazil. The Vazante Mine through the years has always carried out mining on stopes with a thickness larger than 3,5 meters, but nowadays due to the need to reduce the waste planned in its blocks, as well as increase the useful life of mine, mining has been implemented in blocks that are less than two meters. Given this, the challenge is to be able to carry out blasts that does not exceed the operational dilution required and does not generate an impact on recovery, as working with extremely heterogeneous stopes. This study seeks to correlate the main characteristics of stopes and its relationship with the results obtained in the execution of those blasts. Also, it proposes an analysis between the empirical data, and existing theoretical references, creating ideal mining parameters, such as minimum thickness, maximum height, and optimum timing in the blast plan. One of the main challenges for carrying out this mining method is the control of operational dilution, generally pointed out as the biggest difficulty for companies that adopt this methodology, due to the thickness of those stopes, any displacement can make it unfeasible, thus the technical level on carrying out the drilling and loading of these blocks must be impeccable, an understanding of the structural geology of the site is also essential for dilution control. The outcome will be a set of ideal parameters and mining methodology to guarantee the success in execution of these blocks, thus bringing a financial benefit to the company.

Jan 21, 2025

By Guo Ziqing, Tang Qiuming, Liu Yuanyuan

The channel-type non-mechanical stirring production process is a new developed technology for emulsion explosives in recent years. It removes traditional equipment such as mechanical-mixing emulsification, mechanical-mixing sensitization, matrix pumping, and explosive pumping, and has been applied in China. This technique achieves a fusion of higher intrinsic safety and lower cost, as well as the excellent quality of products and high efficiency of production. The emulsion particle diameter is about 0.5μm. The storage period of emulsion explosive produced with span-80 emulsifier is more than 7 months.

Jan 21, 2025

By Joseph A. Meyers

NYC has always been a high-profile target for both foreign and domestic terrorists. Explosives have always been the go-to tool for terrorists to bring about serious physical injury, death, and property damage in our society. Today with the anti-police movement gaining traction in the United States and anarchists groups using homemade explosives against law enforcement and municipalities, it is the responsibility of the explosives industry to ensure that every explosive product on a blasting site is secure. We must prevent the theft of these energetic materials used on projects and sold by vendors so they are not used by these terrorists. We have learned many lessons here in NYC which began with the theft of explosives used for blasting projects in NYC to supply the IRA (Irish Republican Army) 50 years ago. The liability is too significant to take short cuts in securing energetic materials. Over the years through cooperation with all agencies and the industry we in NYC have developed certain proven protocol and procedures we would like to share with the industry. An efficient and effective security plan for the logistic movement of explosives, as well as for the blast site is imperative to keeping the good name of the industry from negative repercussions and possible additional bureaucratic oversight of an industry that is highly regulated and still recovering from the pandemic. Communication, security assessments and transparency with all stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the overall security for the blasting project. This SOP (standard operating procedure) will allow the AHJ to become a proactive partner in the security of the blasting project. If the AHJ is not a law enforcement agency, the law enforcement agency specialty unit must be notified and included in all phases of the project. The security for a blasting project with AHJ and law enforcement input starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. This includes threat assessments on new and existing structures. SME’s (Subject Matter Experts) must be present at all stages. The blasting industry and regulators must work collaboratively to improve safety, security, and create a dialogue with law enforcement and the AHJ. Relationships are built through trust, teamwork, transparency, and communication and greatly improve the safety of our great country.

Jan 21, 2025

By William Hissem

When we look out on our business landscape today, the words higher, faster, fdwther come to mind. Compliance issues, business integration, increasing production and profitability demands are converging in an age old industry and giving it a new twist. Not that the rock changes, rather that as the variables of our business change, the resulting “cut-off grade in business” turns ore into rock or rock into ore. The trick is to emphasize the latter. As with the miners of yore, what was recovered from the business enterprise had a lot to do with tools and skill. So it is today. When the casual observer looks at drilling and blasting operations today, many see the same basic offering in terms of equipment types and process. Looks, however, can be deceiving. As with the aviation sector, a given machine might took similar to previous generations of equipment, but in fact is radically different in terms of power, efficiency, accuracy, and range. So it is with hydraulic top-hammer drills today.

Jan 1, 2000

By César Ugaz Castañeda, Paulo Fernández Alvarado, Richard Sotomayor Oblitas, Rocke Enríquez

Mina El toro has been making substantial changes in its operation to improve its social impact and productivity. Because of the use of gasified emulsions and electronic initiation system, it was possible to mitigate vibrations and carry out massive blasting, increasing its production by 4.2% and minimizing complaints from communities.

Feb 1, 2020

By Douglas Bartley

As the economy continues to slowly recover, our industry continues to finds ways to increase productivity while being forced to cut costs. The drilling and blasting process is the starting point of any aggregate or mining process. Many people refer to it as the “Primary Crusher” as it will always be more efficient to crush rock with explosives energy than it will be mechanical energy. It is the more efficient use of this energy that is addressed in this paper.

Jan 1, 2012

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010

By (Journal for the Fields of Gunpowder and Explosives) Germany (1914 Issues)

RBH Note: The following items are a deviation from the usual content of these articles, but I thought they were kind of interesting from an historical point of view (other than just explosives-history historical.) The interesting things to me are the military-related products, keeping in mind that World War I didn’t start until August, 1914, and then it was kind of an accident of political alliances gone awry. Obviously companies in Germany saw it coming. Of course, all the ads also included dynamite and safety explosives for mining and tunneling as well as the military items.

Jan 1, 2015