Search Documents

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By Kfw Eick

The paper describes the use of the Nonel millisecond delay blasting system in narrow, deep, tabular ore bodies and briefly describes the standard stoping method as used on Harmony Gold Mine and compares this with the new Nonel short panel system.

Jan 1, 1990

By W. Birch, G. D. Rangel-Sharp, L. Bermingham

For many years, the accepted method of Measuring the Velocity of Detonation (VOD) in blast holes has been to use an electric cable of a constant resistance per metre. Thus as the wire is consumed by the explosive in the blast hole, the change in resistance is monitored and when this data is plotted against the time period of the in hole explosion, the VOD can be calculated.

Jan 1, 2011

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By C James Dahn

A new generation of high performance and high density ammonium nitrate prills have been developed. These cycled "prills" offer significant improvement in ANFO mixing time, detonation velocity performance, and heaving capabilities. In addition, their safety characteristics are better than standard ANFO explosives.

Jan 1, 1980

By Travis Watts, Chris Prater, G. T. Lineberry

Moving overburden at minimal cost is becoming increasingly important to coal mining companies throughout the U.S. The coal market is currently doing well, with an average spot coal price for Central Appalachia product (12,500 Btu, 1.2 SO2) standing at $62.00 for the week ending November 11, 2005, so it is at this time that companies stand to achieve healthy rates of return on their investments. Cast blasting is one method of blasting used effectively by some surface mining operations. This method allows most of the overburden to be removed and placed (cast) directly in the spoil pile by the use of explosive energy. With the proper design of a cast blast, a high percentage of overburden material can be directed into piles without the use of earthmoving equipment, hence increasing production and lowering the cost associated with overburden removal.

Jan 1, 2006

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue.

Feb 1, 2020

By Roger Keller, Jason Ryan

A number of studies have evaluated excavation methods for the construction of subsurface facilities for a potential deep geologic repository for the disposal of nuclear waste at Yucca Mountain, NV. Many of these studies suggest that where TBM (tunnel boring machine) methods are not applicable and alternative mechanical excavation methods can not efficiently excavate harder rock drill and blast methods may be the most efficient means of excavation. However, a number of concerns regarding drill and blast applications have been raised in these evaluations, most notably the affects of blasting on the surrounding perimeter, as isolation of the waste by the natural barrier of the surrounding rock is a key element in the concept of a deep geologic repository.

Jan 1, 2001

By Türker Hüdaverdi, Özge Akyildiz

"Efficiency of blast operations depends on fragmentation, overbreak, muckpile profile anddisplacement, vibration, airblast, flyrock and damage to wall or slope stability. To provide all these conditions at the optimal level, determination of rock mass properties (in-situ block size, joint spacing and orientation) is the very first step during design stage of rock blasting. Image analysis software is used not only to determine the fragmentation level of muckpile but also to characterize the bench face. In this study, an image analysis software was used to determine apparent block size of bench face and to measure blast fragmentation of muckpile. The source of errors and the vital points to be taken into consideration were explained for bench face characterization andfragmentation measurement. Since it provides much better results than previous techniques and it is not intrusive to production process, image analysis technique is considered as one of the most efficient and preferred way for fragmentation analysis. Besides these advantages, there are some weak points of image analysis software. Lighting is one of the most important factors for photographs captured for in-situ block size analysis and fragmentation analysis. Lighting determines shadow formation. In an ideal image, particles are clearly delineated by soft shadows. If shadows are too strong (dark), analysis suffers. Appropriate scale should be replaced onto blast muckpile during site measurements. The location of the scale in image affects the results of analysis. Also, the densityand orientation of discontinuities should be considered during application of image analysis technique to characterize bench faces. In this study, image analysis software was applied in thesandstone, limestone quarries of Istanbul region and an open pit boron mine. All image analysis, evaluations and results were made based on the site measurements."

Jan 1, 2017

By A K. Raina, P B. Chourdhury

Flyrock is the unwanted throw of rock fragments to excessive distances in opencast blasting. The incidence is relative in nature incorporating the distance of objects of concern like structures within and outside the mine, equipment within the mine & near the blast and persons within and off the mine. Several attempts to predict and defi ne fl yrock made worldwide could not address the problem since the phenomenon is not a regular feature in blasting. This probabilistic nature of fl yrock allows for risk calculation. CIMFR, India developed a Factor of Safety based risk criterion (10, 14) for evaluation of throw/ fl yrock in opencast mines that incorporates all the above in terms of distance and allowable limit of throw – which in turn determines the risk. The criterion provides the blaster a tool for mathematical evaluation of fl yrock risk in terms of a Factor of Safety and threat ratio (defi ned for the 1st time), thereby enhancing confidence when blasting. The method is easy to use and has been applied to several mines in India and the results are signifi cant. This paper details the evolution of the concept and its application in three limestone mines of India and the results obtained. The application of the method for defi ning a fl exible danger zone is also discussed.

Jan 1, 2008

By Jim Hall, Denis Rickman, Jon Windham, John Ehrgott, Stephen Akers, Byron Armstrong

With the growing concerns about terrorism world-wide, numerous agencies conduct experiments to investigate the effects of terrorist vehicle bombs. In many cases, the vehicle bomb of interest utilizes some form of ammonium nitrate/fuel oil (ANFO) as the explosive source. Due to the high cost of fullscale testing, it is advantageous to conduct at least some vehicle bomb experiments at reduced scale. Extensive testing has shown that ANFO is a non-ideal explosive, and its explosive output does not scale reliably at explosive masses below approximately 400 lb (182 kg). Most scale-model testing requires explosive masses 1 to 5 orders of magnitude smaller. Thus, scale-model testing is typically conducted with “ideal” explosives, such as composition C-4, which perform in a scalable manner at virtually any charge mass. The utilization of an ideal explosive to model ANFO requires the existence of an accurate means of equating the performance of the two explosives. The airblast equivalence of C-4 and ANFO has been well established. However, the cratering equivalence of these explosives is not thoroughly quantified. This is especially true for the case of an above-ground detonation, which is precisely the scenario of interest in vehicle bomb studies. A study has been conducted to better define the cratering equivalence of C-4 and ANFO for above-ground detonations. This paper presents a discussion of results from this research.

Jan 1, 2008

By Kenneth K. Eltschlager, Richard R. Brochu

At the International Society of Explosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this committee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same within stated tolerances.

Jan 1, 1999

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006

By Raymond V. Adolphson

The introduction of a new explosive component in 1955-56, called ANFO, featured much safer, effective blasting characteristics when compared to dynamite, accompanied by a notable reduction in cost. These savings mounted as borehole diameter or depth was increased with ANFO volume subsequently enlarged.

Jan 1, 1983

By Peter P. Harvey

The Nonel Primadet is a non-electric delay blasting cap initiation system. The most recent field application of the system in the Southwest has been at the Magma Superior Mine, Superior, Arizona.

Jan 1, 1978

By William E. Hill

The blasting program at the Valdez Creek Placer Mine must deal with challenging situations throughout the year. During the short summer, extreme water conditions must be confronted, while the winter months present problems of a different nature, where the overburden freezes to a depth of up to 18 feet. These obstacles require techniques borrowed from hardrock blasting combined with creative experimentation to overcome.

Jan 1, 1994

By Robert Hopler

In part four, the instrumentation used to detect the vibrations from the 1876 Hell Gate (East River, New York) reef-clearing blast was discussed. The apparatus consisted of cups of mercury and microscopes or other magnifying instruments to detect ripples or waves on the surface of the liquid metal.

Jan 1, 2007

By Lon D. Santis

This paper reports on an evaluation of the safety characteristics of short lead, 5 centimeter (cm), Magnadet1 detonators. The Magnadet initiation system uses magnetic induction principles to transfer electric energy from the firing line to the detonator without a physical connection. This study was initiated because the Magnadet initiation system represents a new technology and the Bureau is interested in ensuring that no potential safety hazards are introduced into the nation's mining environment. The Magnadet system and its proper use are described along with a discussion of how it works. The potential hazards examined are: stray current from mine service power, lightning, DC current, static electricity, and radio frequency transmissions. Tip strength is also evaluated. Experiments were conducted to evaluate some hazards and theoretical methods were used to evaluate others. The results showed that the Magnadet short lead initiation system does not exhibit any unusual safety hazards. The new system is at least six times as resistant to common hazards as currently used electric initiation systems, so long as the insulation is intact.

Jan 1, 1992

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By Brad Bockey

Whether you are a driver, blaster, or are in charge of filing, you must recognize the importance associated with DOT-required recordkeeping. As various agencies become intertwined with rules governing the explosives industry, the records we produce must be as accurate as possible. The time is right for reviewing your paperwork process from start to finish.

Jan 1, 2011