Search Documents

By Linghu Changjin

Based on the characteristics of typical marine sedimentary phosphate rock in Guizhou, Southwest China, together with the research findings made on the surface electric properties of pure collophanites taken from different areas in pure water and under the action of collectors, a pure minerals flotation test of collophanite was conducted in this research. The differences of collophanite flotation behavior and the effects of the different pH values, varieties, and dosage of collector on flotation separation of collophanite were studied. It is suggested that that in pure water, collophanite had a negative charge within a wide pH range. The electro negativity values of collophanite increased with the addition of collectors GJBW and WF-01. When GJBW and WF-01 were used as collectors, the collophanite was depressed in acid medium, but had a good flotability in basic medium.

Sep 1, 2012

By P. Altinkaya, O. Celep, H. Deveci, E. Y. Yazici

"Copper-bearing gold ores have proved difficult to treat in conventional cyanide leaching process owing to prohibitively high consumption of cyanide by readily soluble copper minerals interfering with gold extraction. Cyanide leaching of gold from copper-rich ores can be improved by intensive cyanidation or application of physical and chemical pre-treatment methods (e.g., ultra-fine grinding, roasting and leaching). In this study, nitric acid leaching of a copper-bearing pyritic concentrate (0.3% Cu, 62 g/t Au and 110 g/t Ag) as pre-treatment prior to cyanidation was investigated. The mineralogical analysis of the concentrate has revealed that it is composed of mainly quartz (25%), pyrite (32.7%), sphalerite (5.37 %), galena (2.12 wt %) and anglesite (1.13 %). Arsenopyrite, chalcopyrite, covellite and bournonite were also detected as minor phases present. Previous studies carried out by the authors showed that direct cyanidation (1.5 g/L NaCN) of the as-received concentrate (d80: 80 µm) produced low gold (45% Au) and silver (46% Ag) extractions. Nitric acid pretreatment of the as-received concentrate was performed for 5 hours at 1-5 M HNO3 and 80oC. In these tests, 65% Cu/Pb and 94% Zn were leached. The nitric acid pre-treatment improved the extraction of gold and silver in subsequent cyanide leaching (1.5 g/L NaCN) to 82% Au and 87.5% Ag with a concomitant decrease (up to 54%) in cyanide consumption. It can be inferred from these findings that the removal of copper from the concentrate and the liberation of the occluded gold by nitric acid leaching as pretreatments can be appropriately employed for the treatment of the copper-bearing pyritic concentrate with high gold/silver content. INTRODUCTION Refractory ores are often characterized by their low amenability to cyanide leaching resulting low (often <80%) Au/Ag extractions (Bhappu, 1990; Celep et al., 2009; Marsden and House, 2006). One of the most common causes of refractoriness is the physical or chemical encapsulation of submicroscopic or fine-grained gold in sulphide minerals such as arsenopyrite and pyrite (La Brooy et al., 1994; Vaughan, 2004). To render refractory gold ores/concentrates amenable to cyanide leaching, the decomposition of sulphide minerals within a pre-treatment process to expose the encapsulated gold grains to the action of cyanide is required. In this regard, roasting, pressure oxidation and biooxidation are commercially used processes for pretreatment of arsenopyrite/pyrite gold ores/concentrates ahead of cyanide leaching (La Brooy et al., 1994). Presence of cyanide-soluble copper minerals in the ore leads to low gold recoveries and high cyanide consumptions under conventional cyanide leaching conditions. High cyanide concentrations (CN:Cu>4) should be employed to achieve high gold recoveries from copper-rich gold ores/concentrates. This may require recovery of cyanide from effluents. In this regard, SART Process (sulphidisation-acidification-recycling-thickening) employed industrially for recovery of cyanide and copper as a by-product. This process simply relies on the addition of sulphide (as Na2S, NaSH or H2S) to the leach solution prior to the acidification to pH 4-5. This results in the precipitation of copper as Cu2S and occurrence of free cyanide which is recycled to the leaching circuit after S/L separation (Dai et al., 2012)."

Jan 1, 2018

By D. Chen

The experiment adopted magnetic separation-priority flotation (first to float copper,then float lead) combined technology to deal with a complex Cu,Pb ,Zn multi-metals ore which has high sulphur content, difficult to separate Cu, Pb ,Zn minerals from sulphur and separate Cu from Pb. Floatable pyrrhotite was separated through magnetic separation which could eliminate the adverse effect on the flotation followed up. And then adopting the priority flotation process to recover the Cu, Pb ,Zn from the magnetic tailings. In priority, flotation Cu, BP(a kind of ethionine ester collector ) and ethyl xanthogenate were used as the collector, LD-1 and sodium sulphite were used as the depressant.The depressants combined with humic acid sodium and lime were used for chalcopyrite ? pyrite separation to further improve the copper concentrate grade. Considering the raw ore that contain 0.32% copper, 0.54% lead and 25.54% sulfur. The copper concentrate grade is 23.61%. The lead content of copper concentrate is only 0.85% . The recovery of copper is 75.03%,and the lead concentrate grade is 54.58%, the copper content of lead concentrate is only 0.81% and the recovery of lead concentrate is 62.24%. The mineral processing indexes were excellent, finally realizing the high effective separation of Cu, Pb , Zn and pyrite. This technique provides a new approach to highly utilize complex copper-lead-zinc ore.

Sep 1, 2012

By Subrata Roy

The slag produced in metallurgical smelting processes contains considerable amount of valuable metals. The present work focuses on recovery of copper value by froth flotation from the copper smelter slag. The slag samples are subjected to detailed characterization including automated quantitative mineralogy using Mineral Liberation Analyzer (MLA). The MLA results indicate that a part of copper is present in sulphide form in fayalite (iron-silicate) matrix and very poorly liberated. SEM-EDX analyses also reveal that a certain part of the copper is present within the fayalite (Fe-Ca-Si) matrix, perhaps either as lattice impurity or very fine grain. The copper smelter slag is ground in wet mode in a ball mill, to particle size distribution suitable for flotation. Subsequently, the slurry undergoes froth-flotation in lab-scale Denver-type flotation cell. Various combinations of sodium iso-propyl xanthate (SIPX) and alkyl hydroxamate collectors are used along with pine oil as frother. A multiple collector dosage is required for effective flotation of non-sulphide copper phases associated fayalite and alkyl hydroxamate is identified as one of the effective collector for non-sulphide minerals. The copper recovery can be enhanced by 7-10% with a combination of collectors as compared to conventional sulphide flotation using only xanthate type collectors. However, the grade decreases to some extent. Keywords: flotation, copper slag, hydroxamate collector

Sep 1, 2012

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By A. Pandey

Over the years, Coal Beneficiation at Tata Steel - West Bokaro has seen varied changes. With increasing R.O.M throughputs & lowering of the concentrate ash, Fine Coal Beneficiation process has thrown up myriad challenges. Development of Synthetic Collector was initiated couple of years back with Technical assistance from NLC Nalco India Ltd. Coal from West Bokaro unit was sent to Nalco?s Naperville (US) research lab for developing Tailor made synthetic collector . After comprehensive lab flotation studies, synthetic collector was developed & recommended for plant evaluation. The lab scale results were very promising in terms of improved separation efficiency & yield at similar ash level. The collector sample received from Nalco research laboratory were revalidated at Nalco Kolkata lab and finally at Tata Steel West Bokaro lab, confirming the promising results. (S.E 25-30 % better than HS Diesel) The key factors playing out for this improvement initiative are a) Scope for improvement in Clean Coal Yield at same or lower ash level coupled with improved Selectivity and Separation Efficiency b) Introduction of a Synthetic Collector with a Green Chemistry and subsequent replacement of H S Diesel, which is highly inflammable with a less inflammable & safer product Trial was conducted at plant scale in two phases and comparative performance of the Collector vis-à-vis Diesel was evaluated across the following Coal Seams of Q- SE (Seam VII, VIII, VI, IX and X). The results generated are very promising and the improvements observed are summarized below. ? Separation efficiency improvement by more than 20% observed. ? Flotation Fines yield increase varied from 0.6- 1.5 % on raw coal basis across different seams. ? Consumption pattern is 20-25 % lower than Diesel. Keywords: synthetic collector, west bokaro, coal beneficiation, HSD

Sep 1, 2012

By B. Orberger

The fine fraction (< 2 mm) of the high grade Mn-ore from the world class Moanda deposit, Francevillan basin, in Gabon, contains up to 30 wt. % of manganese and about 0.4 wt. % phosphorous. A pilot study at laboratory scale integrating mineralogy and geochemistry before and after ultrasonic treatment was conducted on the fine fraction (< 2 mm) of oxidized Mn ore in order to reduce the phosphorous content and enrich this fraction in manganese. The fine fraction was dried, crushed at 2 cm and sieved at 2 mm. The two fractions (< 2 mm and 2 mm ? 2 cm) were investigated by X-ray diffraction and scanning electron microprobe ? electron dispersive spectroscopy analyses. Both fractions contain lithiophorite, cryptomelane and pyrolusite as Mn carrier, and goethite, muscovite, illite and quartz as contaminants. The Mn hydroxide nsutite was only found in the fraction 2mm ? 2 cm.The < 2 mm fraction is significantly richer in goethite, muscovite/illite, and quartz. Phosphorous carriers are mainly goethite (up to 2.8 wt. % P2O5), while the Mn minerals contain up to 0.8 wt. % P2O5. The Mn minerals are partly included in an agglomerate of goethite, muscovite/illite, and quartz. The < 2 mm fraction was treated by ultrasound for 30 s in normal water. Mineralogical and chemical analyses after ultrasound treatment showed that the Mn-minerals were largely liberated from the goethite-muscovite-illite agglomerate. Mass balance calculations show that after ultrasonic treatment the < 2 mm fraction was ? 50 % enriched in Mn and ?50 % impoverished in P.

Sep 1, 2012

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By Rogerio de Oliveira Baldoino

The sedimentary phosphate deposit of Bayovar is located in a very dry area of Peru (desert of Sechura) which is close to the Pacific coast. It consists of seven superposed layers (beds) which call for different strategy of concentration. The ore is composed predominantly by apatite (84% in weight basis) plus silicates (16%). In order to treat the ore from beds 1-5, a suitable standard mineral processing circuit (composed of scrubbing, screening, attrition and desliming) started its operation in 2010, yielding 3.9 Mt/y of concentrate assaying 30% of P2O5. To concentrate phosphate from beds 6-7, however, it is necessary to carry out further cationic reverse flotation of silicates, at neutral pH, to yield a concentrate, which meets market specification. The new process was developed in laboratory scale by a collaborative program conducted between Vale S.A. and the University of Sao Paulo-Brazil. A pilot plant has currently been running in order to confirm the very good results yielded in laboratory scale. The successful accomplishment of flotation in the current beneficiation flow sheet will enable a capacity expansion of 1.9 Mt/y of concentrate assaying 30% of P2O5. As water resources are very limited at Bayovar region, all the steps of concentration, including flotation, must be performed with seawater, which must be continuously recycled. This work addresses some relevant topics related to the use of seawater in the reverse cationic flotation of silicates: influence of temperature, water quality (ageing and chemical composition) and collector type (ether amine versus condensate). The results indicate that condensate amine works better than ether amine. If flotation is conducted with the former collector, the separation process is able to tolerate changes in temperature (25-40oC) and water quality caused by either evaporation or ageing. Keywords: phosphate, flotation, seawater, temperature, ageing, concentration, salt

Sep 1, 2012

Compressive crushing is applied in crushing plants used in mineral, mining, and aggregate in-dustry for fragmentation of rock materials. From a global perspective, the total volume of crushed rock is massive and corresponds to several billion tons. All societies have to fulfil a daily need of rock material products and its derivatives such as metals and minerals. The business for metals and minerals is global while the aggregates production is mainly a local industry. This paper presents a broader overview of optimisation with respect to product yield, use of natural resources and energy consumption. High level plant optimisation of compressive crushing plants is covered as well as real-time optimisation and optimisation of single production units. Each of three optimisation areas are presented and a discussion around how these three areas will be able to communicate with each other is given. Several models, e.g. process performance behav-iour with respect to wear, as well as fitness functions can be common for all three areas. Well-defined and representative fitness functions are of the utmost importance in order to assure that the optimisation results reflect the production targets. It is concluded that great benefits can be achieved by linking together different areas of optimisa-tion. The future for compressing crushing lies, without a doubt, in tailored processes both with re-spect to machines optimised for each customer, plant parameters and operation routines as well as an on-line adjustment, which takes into account current information and control possibilities.

Jan 1, 2014

In order to determine the optimal process parameters of agitation leaching and provide industrial process design parameters, experiments were carried out on leaching behaviors of copper oxide ore with high mud content. Condition tests show that the main factors affect the leaching efficiency as follows: Temperature, Initial acid concentration, leaching time and particle size. As the temperature increases, the copper leaching rate was increased. At 60 ?, the initial acid concentration 80g / L, leaching time 2h, liquid-solid ratio 2:1 and grinding fineness65%-0.074mm, the optimal copper extraction was 83.15%, the acid consumption was 187.91kg / t. ore. Keywords: agitation leaching, copper oxide ore, mud

Sep 1, 2012

By J. E. Gebhardt

Progress is reported on capturing the effects of gangue chemistry in the context of a comprehensive stockpile heap leach model for leaching copper sulfide ores, employing leading edge computational fluid dynamics (CFD) technology. The stockpile is a complex multi-phase process, comprising of a solid porous media, with complex fluid flow, gas and liquid phases, competing solid-liquid reactions, dissolution of minerals and transport through the heap. The model accounts for many of the challenging physical and chemical features of the heap, including transport and reactions kinetics for the important copper and iron sulfide minerals, ferrous oxidation, bacterial effects, thermal energy, acid and sulfate balances. In this contribution, the model has been extended to incorporate dissolution of various species from gangue reactions and precipitation of hydronium and potassium jarosite, ferric hydroxide, alunite, and gypsum. The effect of aeration on the simulation of a copper sulfide heap leach is provided as an example.

Sep 1, 2012

By Z. Q. He

This paper introduces the structure and working principle of SLon magnetic separator that has excellent performance in iron removal, and summarizes a part of the examples of applications, which applies this machine to remove iron from non-metallic ores, and shows widespread prospect of application of this machine in the purification of non-metallic ores.

Jan 1, 2014

By T. Badrujaman

In September 2005, after 30 years experiencing in operating an ESF using a falling water film shell cooling system, Antam entered the new era in operating an ESF, after completely modernized its ESF No. 2 from a falling water film shell cooling system to a copper cooling system. Further, in the beginning of 2007, Ferronickel plant No. 3, where its ESF also uses copper coolers, was successfully commissioned. By operating an ESF using a copper cooling technology, Antam has to face some challenges to establish the operation stability. Besides that, the chances to maximize the furnace efficiency are greatly opened. The shielded-arc mode of electrode tip is selected to operate an ESF under relatively high furnace power to produce metal having tap temperature below 1500? and slag having tap temperature below 1600?. It leads to electric current unbalance. Further, operating an ESF using a copper cooler system under high voltage as consequence of the furnace power raise increases metal and slag tap temperature. This condition damages furnace integrity fast. Besides that, relatively high metal temperature increases its pressure during metal tapping. It leads to failure in closing the metal tap hole. The main different ways in operating an ESF using a falling water film shell cooling system and a copper cooling system lie in the electrode tip mode, the water specification used for cooler, metal tap block maintenance and allowed metal & slag level in furnace. Since a copper cooler system allows an ESF to be operated by consuming nickel ore having ratio Fe / Ni up to eight and producing slag having relatively high Fe content in slag, an undesirable silicon reversion phenomenon becomes an obstacle in reaching the operation stability. A copper cooler technology lets Antam to take a chance to increase its capacity. Modernizing the ESF No.2 had increased its furnace power from 17 MWh to 25 MWh. Meanwhile the ESF No. 3 can be operated up to 42 MWh. This technology allows an ESF to be operated under relatively high furnace power above 25 MWh safely as well as prolong the campaign life of ESF brick. Further, lowering ESF power consumption, extending the limitation of ratio S/M in nickel ore consumed and adjusting Ni grade in ferronickel product can be gained by applying this technology.

Jan 1, 2014

By Xin Tan

In this paper, two types of low-grade complex zinc oxide ores (sandstone and limestone ores) from Yunnan province, China were investigated. A large number of argillaceous and alkaline gangue makes it infeasible to treat the ores with heap leaching. Although wet metallurgy can be considered, the lower efficiency of liquid-solid separation, the high cost, and low revenue limit this technology to be put into practice in large-scale. In order to solve this problem, a new technology combining mineral processing method with metallurgy technique is studied to process this refractory ore that consists of sandstone ore with 5.84 per centZn and limestone ore with 6.50 per centZn. The results of the tests showed that zinc can effectively be recovered from two types of the ores by using the new technology, and the acid consumption can be remarkably reduced. For sandstone sample, 82.96 per cent Zn was recovered by flotation and final Zn recovery by flotation+ hydro-metallurgy can be up to 78.17 per cent from the ore. In addition, for sandstone, acid consumption can be reduced from 270kg/t by direct acid, leaching to 76.92kg/t by flotation + hydrometallurgy combination. For limestone sample, 85.90 per centZn was recovered by flotation and totally 80.95 per cent Zn can be recovered by new technology which is a combination of mineral processing and metallurgy. Besides, H2SO4 consumption can be reduced from 450kg/t for sandstone originally to113.79kg/t after using new technology. One merit of this new process technology is that the zinc sulfides and oxides can be recovered without desliming in the flotation cells at the different stage and make sure the concentrate products as a good feed for hydrometallurgical technology. This study provided pretty good technical support for tapping low-grade refractory zinc oxide ores. Keywords: low-grade zinc oxide ores, limonite, non-desliming beneficiation, flotation + hydrometallurgy combination

Sep 1, 2012

By M. R. Hosseini

Among all gravity concentration methods, Shaking-table is the most effective one from the metallurgical point of view. In this study, Shaking-table was used for concentrating a manganese ore sample from Ghasem Abad area in Kerman, Iran. Experiments were designed by using L8Taguchi design with five variables and each variable in two levels. The influence of each variable and their interactions on the operation of the device was studied. The variables under investigation were: table slope, table frequency, water flowrate, feed rate, and particle size. The manganese concentrate grade and recovery were used as response variables. It was shown that water flowrate, table slope, feed rate, and particle size are the significant variable on concentrate grade; while, all the variables influence manganese recovery.

Jan 1, 2014

By D. P. Chakraborty

Joda East Iron Mine, one of the captive iron ore sources of Tata steel, located in the state of Odisha in eastern India caters to approximately 45% of the iron ore requirement of the Jamshedpur Steel Plant. The iron ore occurring in the mine having high in iron content along with high in alumina. Clay and gibbsite are the predominant mineral phases present as surface coating, fracture filling and/or free occurring and are responsible for alumina content higher. Alumina in iron ore impacts the techno-economic performance of a steel plant by impacting sintering and blast furnace productivity. The impact is even higher when it comes to fine ore used in the blast furnaces in the form of sinter as it constitutes a major portion of the blast furnace burden. Therefore, it is beneficial to upgrade iron ore in the mine head and to reduce alumina before it is subjected to agglomeration. Mineralogical test works reveal, that alumina in iron fines is mainly associated with the clay attached to the hematite particles, either free or interlocked to a very fine size. The paper describes the efforts made to reduce alumina in the iron fines in Joda East processing plant, without much of capital investment for a very sophisticated fines beneficiation circuit. In this process, a suitable dispersant was added in the plant that dispersed the masked slime coating over the iron ore fines, thereby making a better quality iron ore fines with reduced alumina content. The alumina in fines improved by 0.2 units? means from a label of 2.4-2.6 % reduced to 2.2-2.4 %. With this initiative, not only the primary objective of alumina reduction is met but also it has given substantial benefit in reduction of silica and as well as moisture in product. This moisture reduction also has given bottom line impact by reducing idle freight and royalty.

Sep 1, 2012

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014

By Z. He

Based on full investigation of the characteristic of sphalerite in the residue obtained from cyanidation leaching process and the study of the mechanism of the interaction between flotation reagents and sphalerite with the aid of electrochemical analysis, the reagent named YO was developed for eliminating the depression effect of CN- on sphalerite and reducing the dosage of CuSO4. The achievements have been used in commercial production for the treatment of the cyanidation residue to recover the zinc minerals, obtaining a zinc concentrate with grade of 56.49% Zn and recovery of 86.63% Zn.

Jan 1, 2014