Search Documents

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By Aly M. Mohammad

The Delaware River Tramway will link civic and retail developments in Philadelphia, Pennsylvania and Camden, New Jersey. Twin 300-foot towers will anchor the cables at either side of the river. Four high capacity drilled shafts designed by the Geotechnical Department of DMJM+HARRIS support each of the towers. At the Philadelphia tower, each 6-foot diameter shaft extends 130 feet deep and terminates with a 30-foot rock socket. The shafts are situated within the footprint of an existing relieving platform, which complicates the typical construction sequence. Also, the subsurface conditions at the site provide a unique challenge in both the design and construction of the drilled shafts. During the construction of the four-drilled shafts for the Philadelphia tower, a 6000-ton Osterberg load test was performed on the first shaft to verify design assumption and confirm the shaft capacity. The results of the test were utilized to establish load transfer characteristics and develop foundation design parameters suitable for the site conditions. By doing so the Design Engineer was able to reduce the length of the rock sockets on the remaining production shafts by approximately 5 feet per shaft. As a result, the test provided a significant cost saving to the Owner by eliminating 15 feet of rock drilling from the construction costs. This paper presents a description of the unique design and construction methods adopted for the foundations, also on the Osterberg load test including equipment used, number and locations of strain gages, and interpretation of results. The results and findings presented in this paper could benefit both the design and construction industries because it provides a comparison between geotechnical design assumption and actual field measurements; which has always been a challenge particularly for rock formation.

Jan 1, 2002

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006

By Liqun Liang

Various nondestructive testing (NDT) inspection methods are available to evaluate the structural integrity of cast-in-place shafts. The widely used methods include Cross Hole Sonic Logging Testing and Low Strain Testing. Due to its advantages such as low cost, easy operation, quickness and flexibility (no need to plan ahead and prepare inspection tubes or other devices), Low Strain Test is frequently specified in quality assurance programs of many countries or when doubts arise as to the integrity of the finished shafts/piles. The method is well suited for small to middle sized shafts. However it is an indirect NDT testing method and has certain limitations. Data interpretation requires proper training, experience and judgment and, therefore, inconsistent conclusions and reporting may be provided by different testers. To avoid or reduce such inconsistencies, it is best to follow a standardized data interpretation and record classification system. In this paper, a new classification method is presented with examples. A step-by-step data evaluation and interpretation procedure is proposed with examples of real cases to help understand the LST data. The paper also makes recommendations for measures to be taken when anomalies are detected in tested production piles.

Jan 1, 2011

By Gerry Houlahan

The east span of the 3.5 km long SF-Oakland Bay Bridge is supported by different types of foundations along its span. Starting from the west, its first 460 m section comprising twin concrete box-girders is supported by sands and rock on Yerba Buena Island. A 620 m long steel suspension span then bridges a 25 m deep channel that is formed in sediments overlying rock. Twin concrete box girder structures, each 2.4 km long, complete the stretch over the remainder of San Francisco Bay to the engineered earth fill landing at its east end. For most of its length, the Skyway bridges water 3 to 10 m deep over soft surficial Young Bay Mud. The foundation types include spread footings with hold-downs, steel and concrete piles that are set in drilled rock sockets up to 3 m in diameter and 2.5 m diameter steel tubular piles driven to penetrations of up to 100 m. The design and construction-related considerations are presented. The different foundation types, influences of the site geology and earthquake demands on the substructures are discussed. The seismic motions of the bridge superstructures and substructures, as well as the depth-varying soil motions, influenced the foundation design. Together with performance-based design criteria, including post-earthquake footing displacement limits, these seismic demands influenced various aspects of the foundation design, including the use of battered and vertical piles.

Jan 1, 2005

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By Louis Donolo

New buildings in today's urban environment, especially in down-town areas, invariably involve the construction of multiple level basements. Used for parking, storage and commercial space, these underground structures normally extend 30 to 50' and more below grade and, to make optimum use of expensive land, they usually occupy the full site right up to street/sidewalk and property lines. SOIL SUPPORT SOLUTIONS Building these basements requires vertical excavation, and consequently, a temporary soil support system which will eventually be replaced by the permanent foundation walls of the structure.

Jan 1, 1987

By Stefan Larsson, Sebastian Adevik, Sadek Baker, Razvan Ignat

"Abstract Uncertain strength, deformation and flow properties in dry deep mixing columns often lead to conservative choices concerning design values where the design is regularly complemented with a surcharge fill. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle. The deformation properties of a ground improvement were studied by means of two small embankment load tests. The settlement measurements were also used in FEM analyses, where the effect of surcharge on creep settlements was investigated. Based on the results, the effects of the surcharge were considered negligible and could safely be ignored. The project is an example how the contractor can use a field test as an effective design approach.IntroductionGround improvement of soft soils with dry deep mixing columns, or lime-cement columns, is often combined with a surcharge fill. The main reason for using a surcharge is to force the primary settlement and some of the secondary settlement that would have occurred under the final embankment height alone, to take place under the surcharge loading. Another reason is to level out uneven settlements. Strength and deformation properties in improved soil cannot be sufficiently assessed in advance, before columns have been tested on-site, and this uncertainty often lead to conservative choices concerning design values. In order to compensate for a slow forecasted consolidation process, the design is regularly complemented with a surcharge. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle.Extensive research undertaken by Åhnberg (2006, 2007) shows, by means of triaxial and oedometer tests, that cementation processes and a load acting on the columns during hardening, makes the improved soil to behave as a heavily over-consolidated soil due to an increase in quasi pre-consolidation pressure. The effects of using a surcharge on the time for consolidation and creep properties are thus probably small, since the stress level does not normally exceed this quasi pre-consolidation pressure. A study presented by Venda Oliveira et al. (2013) shows that the stress level within small ranges has limited effect on the creep properties.This paper presents a case study where the deformation properties of a ground improvement using dry deep mixing columns was investigated by load tests on two small test embankments. The tests were performed at the Interchange Värtan project site, which is part of the Norra länken infrastructure project in Stockholm. The tests were not performed as a research project but simple load tests performed by the contractor with the purpose of rationalizing the design delivered by the client. One purpose of the load tests was to assess the deformations when the columns are loaded temporarily by overlaying concrete works. Another purpose was to provide some input data to a study of the effects of using surcharge on creep settlements. The analysis was conducted as finite element modeling using the commercial code PLAXIS, where creep settlements can be simulated using the built-in Soft Soil Creep model."

Jan 1, 2014

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980's. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile's resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By Richard J. Finno

Detailed measurements made at a test section adjacent to a deep braced cut and other published data are combined to illustrate the limitations of the common methods of predicting movements associated with excavations in soft to medium clay. While past performance data can be used to estimate expected responses before construction in many cases, actual wall and soil deformations throughout construction can only be estimated using finite element procedures. Success of such analyses depends equally upon considering all aspects of construction that induce strains in adjacent soil, such as wall installation, excavation and bracing sequence, and time, and adequately modeling soil stress-strain behavior. Even when these two criteria are met, soil deformations can not be predicted adequately when strain levels exceed those that produce peak shear stress.

Jan 1, 1991

By Nicolas Denies, Gust Van Lysebetten, Bart Lameire, Jan Maertens, André Vervoort, Noël Huybrechts, Flor De Cock

"Abstract Originally developed for ground improvement works, the deep mixing method (DMM) has increasingly been applied in recent years for the realization of soil and water retaining structures and as alternative to traditional foundation solutions. From practice, there is a real need for practical guidelines dealing with the execution, the design and the control of such applications. With the aim of developing such guidelines, the BBRI ‘Soil Mix’ project was initiated in 2009. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites has been tested. In spite of the large advances in the mechanical characterization of the DSM material, one major issue remains the representativeness of the typical core samples in comparison with the real scale behavior of the soil mix elements. There is among others the question of the influence of the unmixed soft soil inclusions on this behavior and the issue of the scale effect which must be considered in the design. In order to investigate these questions, 8 large scale UCS tests and 17 large scale bending tests have been performed on excavated soil mix elements. The present paper discusses results of this experimental campaign, presents some research perspectives and highlights different aspects related to the design of soil mix elements for the realization of retaining wall or foundation solution.INTRODUCTIONSince several decennia, the deep mixing method (DMM) has been used to improve the strength and deformation characteristics of weak soils. In recent years, deep mixing has increasingly been applied – in Belgium and in other countries – for the realization of soil and water retaining structures and alternative foundation concepts. With regard to the execution of the DMM, one can refer to the European standard EN 14679 on deep mixing (2005) that was elaborated under the umbrella of CEN TC 288 “Execution of special geotechnical works”. However, from practice, it has been experienced that this execution standard does not provide enough pragmatic information and guidelines, in particular for the more recent applications of the deep mixing method (with retaining and bearing functions). The same need by the sector for guidance rules linked to design aspects in the context of Eurocode 7 was experienced as well. With the aim of developing such guidelines and in order to provide feedback to the European standardization platforms, the Belgian Building Research Institute (BBRI) has initiated the BBRI ‘Soil Mix’ project (2009-2013) in collaboration with the KU Leuven and the Belgian Association of Foundation Contractors (ABEF), the Belgian branch of the EFFC. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites, with various soil conditions and for different execution processes (CVR C-mix®, TSM and CSM), has been tested (Denies et al., 2012)."

Jan 1, 2014

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By Michael J. Brown

It is often necessary to undertake some form of pile testing to verify design calculations. Historically this has been limited to static and dynamic tests. Newer rapid testing methods such as Statnamic are seeing more frequent use. This form of testing can be advantageous due to short set up time and test duration. Although the methodology suffers from a lack of formalised guidance and may prove difficult to analyse in certain soil conditions. This paper investigates the suitability of Statnamic testing and analysis for a range of soil and pile types as well as different installation methods through a number of case studies undertaken in the UK. Recommendations are made on test specification and analysis.

Jan 1, 2006

By W. Y. Xu

In comparison with shallow foundation, usually higher bearing capacity, smaller average settlement and better stability are the engineering characteristics of pile foundation. Besides, a smaller differential settlement and a lower settlement rate which will converge quickly are more important characteristics. The superstructure of the building with pile foundation may not meet with significant differential settlement. In this paper, settlement records and other data of different kinds of buildings are chosen to illustrate the characteristics of pile foundation. Moreover, some technical problems in connection with foundation engineering solved in consideration of the above mentioned characteristics of pile foundation are also introduced.

Jan 1, 2010

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By Matthew Janes

Statnamic load testing is becoming widely accepted as a method to quickly and economically determine the load-deflection behaviour and ultimate static resistance of high capacity deep foundations. Strain instrumented large diameter bored shafts were tested at four locations for the federal and state Departments of Transportation in the United States. Tests were conducted vertically (to 30 MN) and laterally on the shafts and, in some cases, testing was completed over water. Instrumented shaft test results provided shaft load distribution with depth and shaft shear transfer stress throughout the soil stratum. Shaft end bearing and ultimate end bearing stress values were provided. On two projects, Osterberg load cells provided comparative static data for skin friction and end bearing. Correlations between Statnamic derived static load-displacement results and Osterberg load-deflection results are very good. Statnamic lateral load test results were correlated with static lateral results in addition to providing useful dynamic response and damping data.

Jan 1, 1996

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By Virendra Singh

The load settlement behaviour of single pile or pile group may be obtained using computer based methods such as the finite or boundary element techniques. An alternative method of obtaining the vertical soil stresses adjacent to the Pile is presented Based on calculated stresses consolidation settlement for Piles foundation is obtained. This approach may be computationally more attractive than the more general finite or boundary element techniques.

Jan 1, 1996