Search Documents

A line of nine self-aspirating W emco cells, part of the Rougher circuit at Division Salvador, Codelco Chile, was retrofitted to allow operation with forced air. Each cell could be operated self-aspirated or with compressed air supplied through a 4-inch line equipped with a mass flow meter. Gas dispersion was characterized for the two modes of operation. Metallurgical performance was compared under self-aspirated conditions and with different gas profiles under forced air conditions. Cell characterization demonstrated that with forced-air the cells could not evenly distribute air across the cell volume. Bubble size increased with gas velocity, as expected, with no difference between self-aspirated and forced-air operation. A systematic increase in bubble size down the bank was found. Cumulative bubble surface area flux down the bank showed no major differences between surveys. However, grade-recovery curves revealed that the highest recoveries were invariably obtained with forced air operation. Plotting concentrate mass recovery vs. enrichment ratio showed that the line performance could be controlled over a wider range when forced air was used.

Jan 1, 2007

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By N. Kolev, M. Poibrenski, I. Nishkov

"The following paper examines the flotation of copper porphyry ores in Assarel concentrator with focus on the reasons for low molybdenum recovery in the final copper concentrate. The copper-porphyry ore of the Assarel deposit is characterized by its variable mineral composition and high clay content, which influence the process efficiency of their concentration. Particle size distribution, chemical and mineralogical analyses have been made on various flotation products showing the distribution of the main elements of interest - copper and molybdenum. It was found that molybdenum is not concentrated into the final copper concentrate as usual in the flotation of copper-molybdenum ores but into the tailings of the copper selective flotation (cleaner tailings). An attempt to explain these results has been made with proposals to improve molybdenum flotation. Low floatability of molybdenite is caused by the ultrafine clay minerals content in both the run-of-mine ore and copper flotation streams. In order to achieve selectivity of copper minerals against pyrite a significant amount of lime is used in the plant leading to higher pH conditions, which could be another possible explanation for the molybdenite depression. The results obtained after the laboratory experiments, showed that it is possible to restore molybdenite floatability using traditional reagents such as diesel, kerosene, etc., and introducing a new polymeric reagent as froth modifier.INTRODUCTIONOne of the main technical difficulties in the area of copper-molybdenum flotation is the selective recovery of both metals, especially the fine (<40 micron) mineral particles. The problem is even more serious when Cu-Mo ore treated contains a lot of natural fine particles, predominantly clays, micas and other gangue minerals. Peng and Zhao (2011) conclude that the mineral processing industry is well aware of the difficulty in treating ores in the presence of clay minerals. Tremolada et al (2010) found that clay minerals have been named as the main problem in ore beneficiation processes due to their small size, which cause a higher viscosity in grinding. In flotation, these clay minerals have natural hydrophobicity or float by entrainment.The impact of clay mineralogy on flotation performance has been reviewed in the literature and the various deleterious roles of clay minerals have been investigated (Bulatovic, Wyslouzil & Kant 1999; Jorjani et al, 2011; Farrokhpay, Bradshaw & Dunn, 2013). It is widely accepted that the actual flotation recovery problem appears to be caused by the properties of these fine particles: small mass (and/or momentum) – high interfacial free energy (Rubio et al., 2007; Farrokhpay, 2011). In most cases, the loss in recovery is found to be insignificant, but the detrimental effect on the concentrate grade is found to be more prominent. The main reasons for the flotation inefficiency are the low probability of bubble-particle collision and adhesion, formation of dense froths and as a result - low process kinetics. A great deal of fine valuable minerals is discarded as slime in flotation due to lack of effective recovery methods."

Jan 1, 2016

By H. A. Wentworth

The Central Manitoba mining district, as spoken of in Manitoba, refers to that portion of the country lying between lake Winnipeg on the west and the Ontario boundary on the east, and from a few miles north of the Wanipigow (or Hole) river on the north, to a few miles south of the Bird river. It embraces two known mineralized belts; the gold area in the north, extending from the shores of lake Winnipeg almost to the Ontario boundary (in a slightly southeasterly direction) a zone some eight or ten miles wide and perhaps forty miles long, lying (for the most part) north, and parallel to, the Manigotagan river; and the Bird river copper and coppernickel deposits, an area not yet clearly defined, but in general lying immediately north of, and roughly parallel to, the Bird river. To the south of the Bird river is a somewhat differently mineralized area, numerous pegmatite dykes being found, with minerals typically associated with such rocks. More specifically, the known gold deposits are largely segregated in the above belt; (1) around English brook; (2) along the north shore of Wanipigow lake; the Rice lake area (about midway of the belt); and the Long Lake-Bulldog lake area, at the eastern end of the belt. Not all the known gold occurences are found in these segregations, but the density of claim staking in these areas is perhaps an indication of the greater number of prospects found in them to date.

Jan 1, 1925

By I. Protkova

Versa Power Systems solid oxide fuel cell (SOFC) stacks operate at intermediate temperatures 700 ? 800 °C allowing the use of metallic interconnects. Thermal expansion good matching with other stack components and cost restriction led to selecting ferritic stainless steels as interconnect material. Analytical tools and techniques were developed to understand the ferritic stainless steel behavior at high temperature while exposed to dual environment. Analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) have provided valuable information towards describing interconnect degradation in a variety of testing conditions. Several examples are presented to demonstrate interconnect oxidation and its relation with SOFC testing results.

Jan 1, 2005

By L. I. Kiss, S. Perron, S. Poncsák, A. Perron

Aluminium industry has an increasing interest in the diminution of the energy consumption of the Hall-Heroult process by the reduction of the anode bottom covering with gas. Electrically isolating carbon-dioxide bubbles, produced at the anode, increase the ohmic resistance of the cell. As the gas production rate is determined by the applied current density, anode covering can be decreased only by a faster evacuation of the gas from the inter-electrode space. Among others, the inclination and curvature of the anode bottom promotes the release of the bubbles and thus decreases the mean value of the covering. Indeed, anode, insert in the molten cryolite bath has a square shape with horizontal bottom. However, inhomogeneous anode consumption, electro-erosion, bath circulation and the inclination of the bath-metal interface modify this shape gradually during electrolysis. Anode bottoms become inclined with rounded comers. This concentrates the gas generation to the center zone of the anode. As the bubble layer cannot be observed directly because of the hostile environment and the opacity of the bath, real scale air-water systems are used to study the impact of the anode geometry on the anode covering and the bubble induced flow. However, the physical properties of such a system are different than that we can found in the real cells. A simulator using the Lagrangian description of the bubble layer has been built and presented in earlier papers. This tool was used to investigate the effect of the anode inclination on gas covering and bath velocity, for both C02-cryolite and air-water system. Results obtained for the second system were compared to experimental data .

Jan 1, 2006

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By Christopher A. Jacobs

Project managers aim to maximise the NPV of their projects, but don&apos;t always appreciate the relationship between mine throughput, project value and the discount rate being used to evaluate their projects. Rate of production or throughput is perhaps one of the most crucial decisions a project manager must make, but if this choice is made arbitrarily, much effort may be spent on a feasibility study that does not optimise project value. The timing of the study in relation to the stage of exploration is examined and simple techniques are presented that project engineers and managers can use to home in on a production rate which will give their project the greatest chance of success.

May 1, 2006

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945

By F. Parada

During copper smelting and converting processes, slag generated is pyrometallurgically cleaned and then disposed, containing around 1 % of this metal. However, important amount of molybdenum initially contained in concentrates also goes to the slag phase. Research on molybdenum recovery from water granulated slags using acid leaching at low temperatures was conducted to find an efficient way for molybdenum extraction with lower magnetite in the slag. However because of the high fayalite content high acid consumption was found. Molybdenum can be recovered from solution using ionic exchange resins, but high silica content interferes with extraction. Some studies addressed to minimize silica extraction as well as alternatives of selective silica precipitation in order to develop a technically feasible process.

Jan 1, 2007

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By A. M. Reyes

Flow field hydrodynamics of serpentine flow channels was investigated numerically using computational fluid dynamics (CFD). The velocity profile simulated by the CFD model was evaluated with respect to experimental results from the literature. Rectangular and tapered flow channels were compared with respect to mixing and water management capabilities, and pressure drop. The CFD model was further developed to account for electrochemical reaction on the cathode side to determine which channel configuration was most effective in reactant conversion. The velocity profile differences between the channels were found to impact reactant conversion, as the rectangular channel had the highest conversion. With respect to water management, although the tapered channel was found to have a higher overall pressure drop, the rectangular channel was found to have higher shear and pressure forces acting on simulated liquid water droplets in the channel.

Jan 1, 2005

By Samuel Nunoo

Gibraltar Mine is an open pit copper-molybdenum mine in central British Columbia. The stability and potential failure modes of pit walls in the Granite Pit are controlled by the orientations of joints and faults. The structural geology also has an impact on as-mined bench geometries. Geotechnical mapping and surveying were conducted using stereo photographs and photogrammetry software. Detailed digital terrain models were constructed to determine the pit wall geometry and the locations and orientations of larger structural features. The pit wall geometry is compared to conventional survey results and the mapped structures are compared to results from a nearby geotechnical borehole.

Aug 1, 2013

By P. Gautier

Current feedstock in the aluminum hot forging processes can be used in the cast or extruded forms. The microstructural variation between as-cast and extruded materials could result in different mechanical properties and corrosion resistance for hot-forged products. Corrosion performances were examined for forged parts produced by two AA6082 feedstocks at different conditions using the following corrosion tests: open circuit potential, anodic polarization, salt spray exposure and corrosion fatigue. With the help of optical and scanning electron microscopes, metallographical investigations were carried out on cast-forged and extruded-forged materials before and after corrosion. The corrosion behavior of both materials was compared in both as-forged and aged tempers. Results show that there is no significant difference in the corrosion performance for final cast-forged and extruded-forged products.

Jan 1, 2011

By D. J. Charlton

"IntroductionMaintenance is a business, which to be successful, requires good management, systems and reporting. The prime objective of the maintenance management group, be they large or small, must be to anticipate and prevent interruptions in operations by keeping equipment in good mechanical condition. This objective should be carried out at minimum cost consistent with maximum productiveness.The objective of this chapter is to give an insight into the various aspects of maintenance management that must be considered to effectively and efficiently operate a mill complex. The degree to which the maintenance sub-systems are developed in an operating mill will be determined by the size of the mill and the needs of the operation.The criterion of the management system used is that the system serve the operation and not vice versa. The systems presented should be considered as tools and, as with all tools, they must be sharpened and replaced as the need arises or as more effective tools become available.To understand what is involved in maintenance management, it is worthwhile to consider a systems approach to analyzing management problems. This approach was developed by J.A.B. Rae while reviewing maintenance management systems for Cominco Ltd.A very simple system involving managing results and objectives is shown diagrammatically in Figure 1.The systems approach to organizational development involves four basic elements: an objective, a result, an activity and feedback. In the analysis, the activity element is broken down into individual actions that people could be held responsible for. If we introduce the action of operating into the diagram of Figure l, we arrive diagrammatically in Figure 2."

Jan 1, 1989

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By M. Pötsch, W. Schubert

"The kinematic analysis of rock blocks is one part of a block stability assessment. It provides information about a block’s movability, i.e. if a block can detach from the adjacent rock mass and move towards the free space. This paper introduces an analytical method for the analysis of pure rotations of arbitrary finite polyhedral blocks. It enables the engineer to judge a block’s rotatability about a corner or an edge. The method is presented using a graphical and computational method. The application of the method is illustrated with an example. INTRODUCTIONThe kinematic analysis of rock blocks deals with the determination of the movability of blocks. Established methods typically cover: (a) translational motion (John 1968, Markland 1972, Londe et al. 1969, 1970, Goodman & Shi 1985, Warburton 1981) and (b) the specific rotational cases Toppling (Goodman & Bray 1977) and Slumping (Kieffer 1998). Mauldon & Goodman (1990, 1996) and Tonon (1998) introduced rotational kinematic analyses for three-joint pyramids and tetrahedral blocks extending Goodman & Shi’s block theory.All mentioned methods are subject to assumptions that limit the applicability to engineering problems. For example, the kinematic test of daylighting joints or intersections inherently assumes a finite block, which only can be proved by the finiteness theorem (Goodman & Shi 1985). Daylighting of an intersection or plane is not a sufficient condition for removability. Goodman & Shi’s and Warburton’s methods are limited to translational block motion. The methods for block rotations so far address tetrahedral blocks only. They also address only pure rotational modes and neglect the general motion of a rigid body. This paper introduces an analytical method for the analysis of the kinematic rotatability of finite rock blocks. It extends Mauldon's and Tonon's theory of rotatability of tetrahedra to arbitrary polyhedral blocks. A graphical method using the stereographic projection and a computational method are presented."

Jan 1, 2015

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015