Search Documents

By Percy Coulter

"GeneralThe Malartic Gold Fields mill is presently treating ore from four different companies. The ore is delivered by truck, by the shipper, and dumped into the Malartic Gold Fields ore bin. This ore varies in size from 'Run of mine' to minus 8 11, All ore is crushed to pass a 3/ 8 11 x 4 11 cross slotted screen.Weighing and SamplingAfter crushing the ore passes over an adequate-weigher (250 T .P.H. capacity) on its way to the fine ore bins. This weigher has a remote counter at the sampling point.A 36” Vezin sampler cuts 15% from the ore stream as it enters the mill bins. This portion is elevated, by means of a short belt conveyor, to feed the No. 2 Vezin sampler. (This elevation is necessary to give headroom for the following machines). The ore on the conveyor is levelled to give a uniform stream to the second sample cutter. The second, third and fourth cutters are 2411 •The No. 2 Vezin sampler cuts 19% from its feed and this portion falls directly into a 1611 x 1011 Denver rolls crusher. This crusher reduces the ore to -1/ 8 11 , approximately. The discharge from the rolls crusher falls on a revolving circular plate with scraper, which gives a uniform stream to the No. 3 Vezin sampler.The No. 3 Vezin cuts 10% from its feed. This portion falls on another revolving plate to give a uniform stream to feed No. 4 Vezin."

Jan 1, 1966

By M. Hajian Heidary

In this investigation, effect of pressure depth on the globulizations of AZ91 magnesium alloy was studied. Cylindrical samples of AZ91 alloy with 1 cm and 2cm in height and 2.5cm in diameter (H/D = 0.4 and 0.8) were prepared, then the samples were hot pressed at 10 and 30% strain at a constant temperature of 200°C; subsequently reheated at 555°C in different times. Results obtained from optical microscopy (OM) showed that the thickness of the samples and consequently, depth of strain affected regions have remarkable effect on the degree of globulization. In addition, it was found that at a constant strain and holding time, structure of thinner samples is more globular than thicker ones.

Jan 1, 2007

By S. Vaidya, R. C. McKellar, N. K. Sinha

Nominally [001]-oriented nickel-base single crystal (SX) superalloy CMSX-10 was investigated at 900°C under constant load, equivalent to an initial stress of 700 MPa, for creep strains from 7% to fracture strain (18.2%). The cross-sectional dimensions of initially uniform cylindrical specimens were measured along their entire length after the tests. The cross-section changed from circular to near elliptical shape. The anisotropic deformation, measured in terms of eccentricity, increased with the increasing strain level, but for a given strain level, it remained constant along the entire length of the initially uniform gauge section. The results are discussed in terms of diameter, eccentricity, area, local stress and microstructural observations. The most striking observation was the fact that all the specimens displayed a yoke-like shape, or the reduction of cross sectional area, at two locations within the originally uniform gauge section. Such observations have not been reported in the literature for single crystal superalloys.

Jan 1, 2006

By Rodrigo A. Marinho

Erratic high grade values are as common in Nature as they are a source of problems for resource estimators. In some highly erratic metal deposits, less than 2% of the drilling samples can represent more than 10% of the total metal in the blocks and they are associated with a high risk level. There is a risk of local overestimation but also of global overestimation, with the high grades being projected over too large a volume. Capping or restriction of these outliers control is being widely used in the industry and commonly applied in resource estimation for the last three decades. The primary purpose of this paper is to present and describe the most applied methodologies for restricting the extrapolation of high grade samples and discuss the results based on a theoretical simulated model. Additionally, this paper demonstrates the economical impact associated with the high-grade and the project risk profile associated with each method.

Oct 1, 2009

By Joseph H. Harris

Shebandowan Mine presents a unique opportunity for the mining industry to demonstrate its willingness and ability to use electrical energy effectively. The mine is a typical 250D-ton/day operation supplied by a i5-MVA power transformer. it is a recent, up-to-date design and operates on a four-day/week, two-shift/day basis. The paper outlines an energy profile based on historical data. It accurately describes the individual and total energy input For: (1) production and non-productive junctions; (2) production and down-time periods; (3) peak and average activity levels; and (4) principal energy utilization equipment. A comparison is then made of production data to electrical data, and production and electrical data to design data. The paper concludes that energy management has an important benefit for the mining industry by assisting in maintaining a competitive operation through reduced costs and fewer production slow-downs in the event of energy shortages.

Jan 1, 1979

By Julie Q. Shang

The electrokinetic (EK) technology for dewatering of two tailings from the uranium mines in Northern Saskatchewan is studied in bench scale experiments. The study includes four phases: 1. Characterization of two uranium mine tailings; 2. Assessment of voltage loss on the coated Ti anode and water interface. 3. EK cell test series to measure electrokinetic permeability (ke) of two tailings; 4. EK dewatering test series to study electrokinetic enhanced gravity dewatering on two tailings samples. The results have demonstrated that both tailings responded positively to the EK process. For the tailings containing gypsum, the EK dewatering should be a short term process (within one hour) with anode conditioning (pH adjustment). The tailings containing clay minerals responded well to EK dewatering, in which pH adjustment is optional and will further enhance the EK flow. Both tailings as tested have low hydraulic conductivity and are particularly suitable for EK dewatering and consolidation.

Aug 1, 2010

By Pierre Bénard

To achieve penetration on the energy market, hydrogen must overcome obstacles in the areas of storage, safety and infrastructure. One of the most important is the onboard storage of hydrogen for transportation applications, where large performance gaps exist between the current state of the technology and user expectations. In order to develop and demonstrate viable hydrogen storage technologies for cars, a set of gravimetric and volumetric system targets have been proposed by the US Department of Energy, based on achieving a driving range of 500 km for a hydrogen powered vehicle. A factor of 2 to 3 improvement in both hydrogen storage capacity and energy density is needed along with several other performance goals. Another key issue is safety. Although some of the safety issues can be arguably assigned to misperceptions, hydrogen has specific properties that have to be addressed, particularly in confined geometries where the risk of hydrogen detonations becomes an issue.

May 1, 2007

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By Steven R. McCutcheon

"The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No. 12, with total reserves (including past production) of 148 million tonnes grading about 12.5% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz (± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeo chemistry of least altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary signature. The two types can be distinguished on the basis of total alkalies (Na2 + K2O) versus SiO2/Al2O3 and Ti02 versus Fe/(Fe +Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies Oacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal bearing fluids and cold seawater. High Fe/(Fe+Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophicallyfrom an acquifer in the footwall stratigraphy."

Jan 1, 1992

By Simon C. Dominy, Ian M. Platten

"Abstract - Gold-bearing quartz reefs commonly show extremely erratic and unpredictable grade variation, although gross geological continuity may be good. This type of variation is often described as being nuggety or having a high nugget effect and can be measured quantitatively using the semivariogram. Understanding of geological features such as reef texture and structure will provide improved models for the interpretation of assay data, drill core descriptions, etc. In this paper, a case study from the quartz-hosted gold occurrences in the Gwynfynydd mine, United Kingdom, is described. The work provides a starting point for models of lateral variation and demonstrates the types of structural and textural features that may be sought to give clues to the prediction of gold distribution in similar deposits. Gold deposition at Gwynfynydd is primarily associated with the reef footwall. The host veins form a discrete group of structures that may have been emplaced early in the sequence of quartz veins forming the reef. This potentially exposes them to a maximum number of dissection events during repeat dilations of the lode. Gold was deposited in the local porosity at extreme concentrations, equivalent to kg/t grades, when the host fissure had become filled with a porous framework of crystalline quartz and sulfides. Distribution of porosity varied laterally along the vein as the result of the formation of clump-like growths of minerals from the vein walls. The growth style is relevant to the distribution of gold although it may not be relevant to the occurrence of gold in a particular vein. The preservation of pores with some connectivity late in the vein fill sequence may be important in permitting continued but slow fluid flows. This facilitates effective fluid reaction with wall rock-derived methane, thus changing the relative rates of gold and quartz deposition in favor of gold. The textural studies explain the first-order control of nugget distribution at Gwynfynydd but do not allow for prediction and optimization of the resource estimation process. This is principally because of the very low geological continuity and poor predictability of the high-grade pockets. Nonetheless, the work does provide a clear geological explanation for the erratic nature of the gold. It indicates textures and structures that can be used to determine geological continuity of the goldbearing elements within the gross reef envelope."

Jan 1, 2001

By Willie Manfrey, Richard Klimpel

This paper describes the effects of slurry viscosity on the selection-for-breakage and breakage distribution parameters in the wet grinding of cres. A series of experimental tests were run on laboratory scale ball mills. Slurry viscosities were modified by varying the solids/water ratio with and without the presence of selected chemicals. Very consistent and predictable correlations are shown to exist. The grinding parameters were calculated using a computerized back -calculation technique developed by Klimpel and Austin. Industrial scale circuit calculations and preliminary plant trial data suggest that considerable increases in throughput and/or fineness of grind can he achieved through the judicious use of chemical additives.

Jan 1, 1977

By F. Rosenblum, P. Spira

"A correlation has been established between the oxygen demand of Brunswick Mining and Smelting ore and flotation results at the bench, pilot plant and operating plant scale. A method of dete""1llining the aeration requirement of sulphide ores on the basis of this correlation is presented. It is shown that abraded iron from grinding media plays an important role in aeration and flotation. Laboratory grinding must therefore be conducted under controlled conditions with suitable grinding media in order to obtain the true aeration requirement of the ore.A method of evaluating aerator efficiency, also based on oxygen demand measurements, has been used successfully at Brunswick Mining to design pilot plant and full-scale aeration systems.1. IntroductionPre-flotation aeration of sulphide pulps has been practiced in the Noranda Group for many years to help in the depression of pyrite and pyrrhotite and to promote chalcopyrite and/or galena. Recently, two out of three parallel circuits at the Brunswick Mining and Smelting Corp. Ltd. concentrator have been converted on a test basis to a new flowsheet incorporating aeration as a basic step. Among other benefits, a substantial decrease in the middlings load has been achieved as a result of improved pyrite rejection. There has been increasing interest in other organizations in the potential advantages to be derived from' aeration in terms of improved metallurgy and/or decreased reagent consumption."

Jan 1, 1978

By Robert D. Brown

The federal government kicked off the new budget season in November 1978, when Finance Minister Chretien announced a handful of proposed amendments to provisions of the federal Income Tax Act and Regulations affecting mining. (See Tax Notes in the January 1979 issue of the CIM Bulletin.) Declaring in his budget speech that these changes were in response to the report of the joint federal/provincial task force on resource taxation, Mr. Chretien tossed the ball to the provinces-" I want to take the lead here... I feel confident that the provinces will do their part". Quebec and Ontario, picking up the ball in their spring budgets, have announced favourable modifications to the provincial taxes on mining, with these moves being paralleled in the recent Manitoba budget, which proposes a flatrate mining tax to replace the previous controversial two-tier royalty. In the meantime, the federal government passed a host of amendments to the federal earned depletion regulations. The result is yet another batch of complex tax changes for the industry to note and digest, but this time with the hopeful factor that most of the changes are favourable to the industry. This article reviews the current status of the federal budget changes, comments on the Ontario, Quebec and Manitoba proposals, and reports on the changes to the earned depletion regulations that were passed by Order-in Council in March 1979.

Jan 1, 1979

By David M. Parkes, George E. Davies

"Mathematically, the proposed formula is: ""Human Effectiveness + Technological Improvement = Success in the Nineties"". A brief review is made of geology, level of technology, management and labour situations, and range of production costs in coal producing countries. This comparison shows keen competition for Canadian coals, especially from the People's Republic of China, South Africa and Australia. Domestic competition comes from nuclear energy, hydro-electric generation, natural gas (if permitted) and eastern United States coal.The huge increase in the size and power of surface mining equipment in the last forty years led to modern large-scale open pit mining. While conventional truck and shovel operations will continue to be widely used, more continuous mining and conveying systems will be installed as pits become deeper and haul distances longer. Computer systems will become more sophisticated and their applications more widespread, leading to higher productivity and closer control of all operations and equipment performances and to partial or complete automation of certain operations.The underground revival will be driven by a new generation of mining people, cooperating to produce over 3 million t/y from 300 m longwall faces retreating over 3 km resulting in mine productivities of over 40 tonnes per man shift, as is already achieved in several mines throughout the world. Continuous operation using on-line control system will assist in consistent production with availabilities over 75%."

Jan 1, 1991

By Donald J. Farrish

"Mr. Chairman and fellow CMP members, most of these remarks will be made with particular reference to copper concentrate but the basics apply generally to other metal concentrates as well.For very good reasons, using copper as an example, smelting capacity usually is located either close to mine production or close to areas of high copper consumption. The mine producer can add on smelting capacity to insure that the copper in his concentrate can be processed into a marketable form under more or less controlled conditions including costs. On the other hand, the consumer wishing to assure a better supply of copper likewise can build smelting capacity and offer treatment charges attractive enough to discourage mines from investing in their own facilities. In this regard, freight is an important factor. Bulk shipments from the heart of Africa with a large overland component are uneconomic whereas concentrate movements from Australia or South America compare favourably with smaller metal shipments.A mine project which incorporates smelting capacity, will often, through the presence of this capacity, encourage active exploration and development of additional concentrate production in the vicinity. The usual result is that new mines within reasonable distance of the smelter will be able to avoid the capital required to build their own smelting and refining facilities and that the existing facilities will expand to appreciate economies of scale."

Jan 1, 1978

By V. M. Robb, F. Walraven, L. J. Robb

"The old Albert Silver Mine is a polymetallic deposit comprising concentrations of CuPb- Zn-Ag-U-F within a set of sub-parallel quartz-hematite veins which occur within the fine-grained apical phase of the 2050 Ma old A-type Bushveld granites. Mineralization occurs as an early pyritechalcopyrite- arsenopyrite-galena-sphalerite-(argentiferous) tetrahedrite paragenesis followed by a later, more oxidized assemblage comprising chlorite-hematite-fluorite-pitchblende. Accumulation of metals appears to have taken place at the interface between a coarse-grained porphyritic granite and an overlying fine-grained phase: veins occur in the latter and represent leakage of magmatic fluids from the differentiated, water-saturated, subjacent granite.Mineralization processes in the Bushveld granites are believed to be related to long-lived circulation of dominantly magmatic fluids stimulated by the high heat productive capacity of the host rocks. Endo- and exogranitic tin-tungsten and base metal mineralization formed during an evolving hydrothermal system that lasted for several hundred million years, forming innumerable small- to mediumscale polymetallic deposits. At the Albert Silver Mine, unroofmg of the cover sequences at circa 1600 Ma to 1700 Ma resulted in the incursion of lower-temperature, high-f02 meteoric fluids which remobilized the earlier sulfides and introduced the paragenetically late U-F mineralization."

Jan 1, 1994

By Elhachmi Es-Sadiqi

"For over 40 years, CANMET has focused its research on value-added products and energy efficiency in the metals industry. The Efficient Metal Production Program is currently managed by Dr. Elhachmi Es-Sadiqi, and the Canadian steel industry is its main client — both directly and through international organizations such as the American Iron and Steel Institute (AISI) and the International Lead and Zinc Research Organization. AISI membership includes Canadian steel companies IPSCO, Dofasco, Stelco, Algoma Steel and Sidbec Dosco.Canada’s steel industry makes important contributions to the economy. The industry comprises 14 companies and employs 33 600 people in locations such as Sydney, Nova Scotia; Tracy, Quebec; Selkirk, Manitoba; Saskatoon, Saskatchewan; and Sault Ste. Marie, Ontario. With annual production at about 16 million tonnes, sales in 1995 totalled $11 billion, $3.8 billion of which was exported.Canada’s steel industry supplies the transportation, oil and gas, appliance, packaging and construction industries. It is at the forefront of new technology use and has a substantial support network to provide raw materials, equipment and service. Three main segments of the industry include flat-rolled products (e.g., plate and sheet steels), long products (e.g., concrete reinforcing bar and structural steel), and specialty and alloy steels (e.g., stainless steel and tool steels, in both long and flat products)."

Jan 1, 1998

By G. N. Carlson, C. H. Hazelroth, D. R. Dorrance

"Located on the north shore of the St. Lawrence River at Pointe Noire, Quebec are the agglomeration and ship-ping facilities of the Wabush Mines complex. Here, the specular hematite concentrate from the Scully Mine is received for further processing. Modern facilities for handling the ore, either to the 1plant or to stockpile, provide quick and efficient operation of the ore receiving station. Physical preparation of the ore for balling is accomplished with regrind ball mills, filters, bentonite crushing and drying facilities, pumps and related conveying circuits. Rotating table feeders deliver the reground and de-watered ore from storage bins to balling drums, where green ball or green pellet formation is achieved. The green balls are then conveyed to the indurating section. Three Dravo-Lurgi travelling grates, producing a total of 6,000,000 long dry tons of pellets per year, are used in the indurating phase of the operation. These grates, having 38 windboxes and firing at a temperature of 2,500°F, harden the pellets for shipment to various blast furnaces throughout the world."

Jan 1, 1969

By W. Marnette

The copper demand is booming. New epicentres with strong dynamic economic growth have arisen in China and other emerging markets. Furthermore, Europe contributes to higher copper demand due to positive economic growth. China and India are therefore expanding their smelter industries, with the backing of a coordinated policy of global raw material sourcing, which includes investments in raw material deposits and state-run measures to support their international trade and competition. Likewise, Europe faces scarcity of copper raw materials. The copper industry in Europe is historically grown and shows excellence in environmental protection and technical leadership. Recycling has always been an important sector. This reiterates the recycling-know-how which exists in the European sector. However, Europe still relies on importing a considerable amount of raw materials from foreign countries. As a result, the global competition for copper and copper raw materials has increased. Tough competition as regards industrial location and costs, the emergence of corporate concentrations and the use of protectionist trading practices by countries like China and India, which distort the markets, now determine the picture. Hence, a copper smelter in Europe is forced to develop tailor-made concepts to safeguard and improve its international competitive position. It is imperative that this is also flanked by improved conditions on the local level and a European raw material policy which takes account of the changed situation on the world market.

Jan 1, 2007

By J. A. Drozdiak, A. Bamber

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012