Search Documents

By H. L. Cameron

General Statement In July, 1948, experimental aerial photography o shallow water zones on Northumberland strait was carried out by the Nova Scotia Research Foundation. This work was designed to test the feasibility of aerial photography for coastal surveys o various types, including seaweed and bottom detail surveys. In the course of the work at Lismore, undersea faulting was noted visually and was later clearly apparent in the photographs. In order to prove beyond doubt that the lineations photographed are actually faults, a ground check was made, and terrestrial stereoscopic photographs were obtained of these features where they intersect the shore line. There can be no doubt of their nature, and the type of faulting is probably thrusting due to compressive forces. This is indicated by the successive right- and left-hand displacements on intersecting faults. The age of the fracturing is post Lower-Pennsylvanian (Lismore) and is correlated with similar compression faulting in western Cape Breton. As far as can be ascertained, this is the first time that subsea faulting has been photographed, though it is quite possible that similar structures have been observed elsewhere. Location and Area Lismore is on Northumberland strait, approximately thirty-five miles east of Pictou (see index map, Figure 1). The area mapped from aerial photographs (Figure 2) is a strip approximately two miles long by a quarter of a mile wide. Figure 3 shows a stereo-pair of the aerial photographs used to construct this map. The terrestrial stereoscopic photographs (Figure 4) show one of the faults.

Jan 1, 1949

By Larry B. Smith

"Feasibility studies are the means by which mineral reserves are established prior to financing a project. However, guidelines are generally lacking for the content, data quality and accuracy of these studies. Regulators take a principle-based rather than prescriptive approach to the content of studies and look to the industry to define study content. Professional organizations, engineering firms and mining companies must eventually establish guidelines and best practices for this work. Most likely these will draw on standards or “stage gates” that have been developed by major mining houses and engineering firms. Engineering studies must: 1.,Define optimal mining and processing methods, production rates, infrastructure, product sales, environmental management and risk mitigation. 2.,Increase confidence in resources, reserves, production plans, processing performance, infrastructure design, environmental management, permitting, capital and operating costs, and financial performance to support financing. 3.,Provide engineering designs suitable for accurate cost estimates. 4.,Develop project execution plans with sufficient confidence that project delays and cost overruns will not occur. Conceptual (scoping, preliminary assessment) Establish the principal characteristics of the project from the geology, resources, metallurgy and development constraints. Assess different approaches to mining and processing. Identify project execution requirements. Test project viability with economic analyses. Recommend additional work to increase the confidence in geology, resources, metallurgical performance, infrastructure, operating and capital costs, environmental conditions and permitting to allow selection of the best development options."

Jan 1, 2003

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By Y. Chunhua, L. Chunsheng, W. Sheng

"Countercurrent solvent extraction is the dominant industrial rare earth separation method. For the rare earth separation, with low separation factors and multiple components, designing and optimization plays an important role in reaching product quality and reducing separation plant costs. Based on the theory of countercurrent extraction, cost-efficient methods, such as third-outlet separation and hyperlinked extraction processing, have been introduced following computer simulation. The consumption and fixed investment of industrial practice are compared, by which advantages of the optimized rare earth separation process are indicated. INTRODUCTIONThe rare earths (RE) have outstanding optical, magnetic and electric properties in advanced material applications and have therefore received much international attention in recent years. Liquid-liquid extraction is the major industrial RE separation method and is widely used in the industry. Supported by the government and with collaboration from the institutions and enterprises, China has made great progress in RE separation, and has become the dominant supplier of separated RE products. Complicated by multiple elements and low separation factors, careful design of RE separation processes is vital for the quality and cost of production. The theory of separation is the key to basic of flowsheet design and industrial applications.BASIC SEPARATION PROCESS AND THEORYGeneral ProcessAcidic extractants such as P507, P204 and naphthenic acid, are the most popular extractants in modern RE separation industry. In the general separating process, the extractant is saponified with a base, then ion-exchanged with RE solutions, thereby to provide stable and high RE loading in the extractant to fulfill the requirement of production quantity and quality. The RE-loaded extractant is then countercurrently extracted and scrubbed with RE solutions and the RE element thereby is purified. After the countercurrent extraction process, the RE-loaded extractant is stripped with acid to obtain an aqueous RE product, and prepare the extractant for recycling (Xu, 1995)."

Jan 1, 2012

The quality of refractory bricks and castables could be determined by direct measurements of their material properties such as elastic properties, porosity, density, etc. using conventional static or non-destructive testing (NDT) dynamic techniques. Quality monitoring of refractory linings is much more challenging and complicated. The static methods require undesirable drilling and sample extractions from the furnace structure. A more desirable alternative is the use of NDT techniques for material quality estimation. The Acousto Ultrasonic-Echo (AU-E) technique is a new stress wave propagation approach for monitoring the quality of refractory linings in operating furnaces. In this paper, the conceptual methodology for the AU-E technique is described, the capabilities and limitations are expanded, and the results from two case studies are discussed.

Jan 1, 2005

By N. Moelans, I. Bellemans, K. Verbeken

In this work, we present a phase field model to simulate the facetted crystallization of Fe3O4 in a quaternary FeO-Fe2O3-Cu2O-SiO2 melt under different partial pressures of oxygen. An important focus in creating more realistic phase field models is the incorporation of the thermodynamic driving forces in multicomponent multiphase-field models by coupling to thermodynamic databases. The diffusion of FeO, Fe2O3 and Cu2O is considered. The ratio of FeO/Fe2O3 at the upper boundary is in equilibrium with the oxygen fugacity of the atmosphere, while conserving Fe. Two-dimensional simulations are performed with different varying oxygen fugacity in the atmosphere. For the considered composition range, the growth velocities of the spinel crystals increase with decreasing oxygen fugacity. INTRODUCTION Crystallization of silicate melts has its applications in geology, pyrometallurgy and glass making. In pyrometallurgy, the solidification of slags influences the freeze lining behaviour (Campforts et al., 2007) and the cooling of slag after tapping (Durinck, Jones, Blanpain, & Wollants, 2008). Modeling of silicate melt crystallization is frequently done on the macroscopic level, using thermodynamic equilibrium calculations to determine the fractions of all phases as a function of temperature. The Factsage software and database package (Bale et al., 2016, 2009, 2002) already proved its usefulness in pyrometallurgical applications, for example to model the phase mixture after solidification of a stainless steel slag (Durinck et al., 2008). Crystallization of phases typically results in complex morphologies on the mesoscale, e.g. dendrites or facetted growth. On this mesoscale, the phase field concept has proved to be a very powerful tool (Moelans, Blanpain, & Wollants, 2008) for modeling crystallizing microstructures, because it can treat arbitrarily complex interface shapes with minimal mathematical complexity. In contrast to macroscopic models, the diffusion profiles and crystallization kinetics can be described as well as the morphology of individual crystals. First, Kobayashi (Kobayashi, 1993) simulated a growing dendrite in a pure undercooled metallic liquid. Then, Warren and Boettinger (1995) simulated a dendrite in an isothermal system considering a binary alloy. The extension to multi-phase systems was done by Steinbach et al. (1996). This was further extended by Tiaden, Nestler, Diepers, and Steinbach (1998) to a framework with coupled diffusion and phase field equations in multi-component systems.

Jan 1, 2019

By D. Purdie

"This paper aims to remind researchers, designers, operators, and managers about the benefits of seeding in the design of precipitation stages in their flowsheet. Including a high density solids (HDS™) process encourages the precipitating solids to form on the surface of existing precipitated particles. This paper discusses the application of the HDS technology at Kennecott Smelter, where the authors have witnessed significant improvements in settling and filtration rates. The authors have also applied this technology at various smelter bleed treatment plants worldwide with similar improvements in precipitation and filtration rates. HDS is a registered trademark of De Nora Water Technologies. RÉSUMÉ Cet article a pour objectif de rappeler aux chercheurs, aux concepteurs, aux exploitants et aux administrateurs les avantages de l’ensemencement dans la conception des étapes de précipitation de leur schéma de traitement. L’introduction d’un procédé des boues haute densité (procédé HDS™, de l’anglais high density sludge) encourage la formation de substances solides précipitantes à la surface des particules précipitées existantes. Cet article porte sur l’application de la technologie HDS à la fonderie Kennecott, où les auteurs ont observé des améliorations importantes au niveau de la vitesse de sédimentation et de filtration. Ils ont également appliqué cette technologie à diverses usines de traitement des rejets liquides des fonderies dans le monde entier, et ont constaté des améliorations similaires en termes de vitesse de précipitation et de filtration. Le procédé HDS est une marque de commerce déposée du fabricant De Nora Water Technologies.INTRODUCTION In 1966, the lead author worked as an assistant smelting metallurgist for the Tsumeb Corporation Limited copper and lead smelter in Tsumeb, Namibia. The smelter produced copper and lead, as well as cadmium and arsenic trioxide as byproducts. The cadmium was concentrated in the lead blast furnace off gas dust, and was collected by a baghouse. The baghouse dust was leached with dilute sulfuric acid (H2SO4) in a batch process. The iron and arsenic in the solution were oxidized with potassium permanganate (KMnO4) and basic ferric arsenate (BFAS; Fe(AsO4)x(SO4)y(OH)z·wH2O) was precipitated using milk of lime. The cadmium was cemented from the purified solution using zinc dust."

Jan 1, 2018

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By Franc R. Joubin, Donald H. James

"The Property of Rix Athabasca Uranium Mines Limited is in the Beaverlodge area of northwestern Saskatchewan. The mine is 7 miles by road north from the Lake Athabasca port of Bushell which is 250 miles north by aircraft or boat from railhead at Waterways, Alberta.The Rix property is a portion of the former DD 1 concession, obtained in 1949 from the government of Saskatchewan when private prospecting for uranium became permissible. The concession was prospected in detail during the 1950 and 1951 field seasons and a great many radioactive show-ings were discovered. Development and drilling were concentrated in two and later three of these areas, and by late 1952 enough ore had been indicated in the Leonard series and ""Smitty"" zone to justify underground development by adit-drift and shaft respectively.Four hundred feet of drift development on the Leonard No. 1 vein and the sinking of a two-level vertical shaft with related lateral development on the Smitty zone were completed in 1953. In April 1954 the Smitty section was placed in production at a rate averaging 100 tons per day, thereupon becoming the first privately owned post-war uranium producer in Canada. The ore is shipped for processing 12 miles by truck to the mill of Eldorado Mining and Refining Limited.Until recently all of the Company's production was drawn from the Smitty orebody. In April, 1955, ore production commenced from the faulted west extension of the Smitty structure, known as the Rix 62 zone, and from the Leonard No. 1 vein.The Smitty orebody (see Figure 2) is an intensely brecciated lenticular zone bordering both sides of the Smitty fault. The breccia areas are irregularly mineralized with pitchblende, very sparse galena, and pyrite in a gangue of feldspar, chlorite, calcite, and silica, all thoroughly soaked with fine-grained hematite to produce the locally-called ""red alteration"".Tenor of the ore currently being mined is classified information. The average grade estimated, prior to production, was 0.20 per cent (4.0 lbs.) U308 per ton."

Jan 1, 1949

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By G. A. Gamble

"The inlet air velocity profile of any surface mine ventilation fan is an important factor when designing the connecting ductwork from the mine shaft collar to the fan. Deficient fan performance can be the result of ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). The need for optimized inlet air conditions begins with discussing the process of performance testing during the development of the fan performance curve. Additional discussions include design of the shaft collar connection and the connecting ductwork. A preferred design of ductwork for parallel fan installations will be illustrated.INTRODUCTIONThe inlet air velocity profile of any surface installed mine ventilation fan is one of the most important factors to consider when designing the connecting ductwork from the mine shaft collar to the fan. Oftentimes deficient fan performance can be traced to poorly designed ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). Such designs may lead to added power requirement, excessive vibration and noise, and reduced fan performance.Understanding the need for optimized inlet air conditions begins with discussing the process utilized when factory testing takes place during the development of the fan performance curve.Additional discussions include design considerations for the shaft collar connection, the connecting ductwork, and fan inlet. Illustrations of cost savings and pressure losses will be included for audience consideration. The design of ductwork for parallel fan installations on the surface is another issue that requires consideration. A preferred method will be illustrated.The selection of accessory components, such as self-closing doors, can also add to the potential for reduced fan performance. Several components will be discussed.An elementary presentation of the Air Movement and Control Association (AMCA) Standard 201 “Fans and Systems” will be included to provide background for those audience members that want additional technical explanations of the need for a uniform inlet air velocity profile at the fan inlet."

Jan 1, 2019

By Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"A Jet Diffuser Flotation Column (JDFC) is a newcomer flotation device whose operation principles similar with Jameson cell but it has an essential change in downcomer. By taking into account the hydrodynamic and fluid mechanic principles (Sahbaz et al. 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogenous dissipation of the bubbles in the separation tank. Thus the performance increase has been aimed for the coarse particles.According to theoretical results, obtained by the formula of Oteyaka (1993) showing the relationship between velocity gradient and maximum floatable size for the various contact angles, the d50 of quartz flotation of JFDC is about 240 µm and 310 µm for the contact angle of 50° and 60°, respectively. This result was verified by the experiments. According to the experimental results; d50 which was accepted the maximum floatable particle size of quartz flotation of JFDC was about 256 µm and 300 µm for the contact angle of 50° and 60°, respectively.INTRODUCTIONFlotation is a kinetic process used for separation of hydrophobic particles from hydrophilic particles. There are many different parameters affects the success of the flotation and particle size is one of them. While the flotation is very efficient for intermediate size, the efficiency of the process starts to decrease for both fine and coarse sizes (Trahar, 1981; Muganda et al., 2011). Therefore; researchers have tried to find a solution for the efficiency decrease in fine and coarse sizes by modifying the chemical condition and designing the new devices. For example, Jameson cell is a unique device for the fine particle flotation due to the suitable design and fine bubble producing (Jameson, 1988; Evans et al., 1995; Sahbaz, 2010). Because of this success operation the Jameson cell is applied more than 200 flotation plants in worldwide. On the contrary, the efficiency of the cell decreases for coarse particle flotation due to the turbulence occurred in the separation tank (Sahbaz, 2010; Cowburn et al., 2007). That’s why, new flotation device was designed in loboratory scale by Sahbaz, Oteyaka and Ucar in 2010s and it has been called as Jet Diffuser Flotation Column (JDFC) recently."

Jan 1, 2016

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter's rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it 'is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

By R. E. Stewart

"Using the concept of economic life and marginal analysis, it can be shown that proper equipment replacement timing can save a mining company many thousands of dollars. To assist management with determining the economic life of mining equipment, a new computer package has been developed. The package, called ERG (equipment replacement guide), incorporates all important economic factors related to equipment usage, such as operating costs, maintenance costs, salvage values, depreciation, volume of work, tax credits, inflation rates, ROJ, etc. The information is used in a series of equations which balance the costs of new equipment against the total cost of old equipment. The solution of the equations determines economic life and the point in time when the old equipment should be replaced. IntroductionIn an operating mine, equipment must eventually be replaced or downgraded for a variety of reasons. Fleets of haul trucks, dozers and other major pieces of equipment deteriorate over time until the mounting costs of maintenance and repair force either a major overhaul or the ir replacement by new and more efficient pieces of equipment.The question of determining the best time to replace old equipment has been approached in many different ways. Various methods, ranging from operating experience, intuition and physical necessity to sophisticated computer models have been devised to help cope with equipment replacement decisions . The best of the se will incorporate the most important economic factors related to equipment usage, such as operating and maintenance costs, salvage values, depreciation, work delivered, the cost of capital, tax credits and, of course, the effects of inflation.Economic TheoryThe fundamentals of equipment replacement theory grew out of the interaction between economics, engineering and finance. The use of annual cost comparisons and rate-of return calculations were helpful in handling situations in which assets with different finite lives were being compared. Later developments bringing together the concept of economic life and marginal analysis helped provide additional refinements to the theory. Taylorui showed that the displacement of an aging asset with a similar, but newer, asset can be justified economically when the marginal cost of keeping the asset one more year exceeds the minimum uniform annual cost equivalent of the proposed replacement."

Jan 1, 1980

By Ming’an Wei, Qifu Duan, Chengtie Wang, Jianmin Wu, Erdenet Mining Corporation, Lusheng Zhou, Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company SKEGA first introduced the rubber magnetic liner, and then followed by the Chinese metal magnetic liners. Traditionally, both liners were used in secondary and regrind ball mills, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design globally. Due to the larger ball mills and thus larger grinding balls (up to 80 mm) especially in non-ferrous metal industry, the application of magnetic liners has been very limited. Based on the new development of materials, the HMR Group Limited has been exploring new designs of magnetic liners which led to the invention of the Nano Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5m x 6.5m ball mill with 80 mm balls at the Erdenet Copper Mine in Mongolia. Although the first set of liner had a service life of 12 months, the design of the second set was modified and improved to accommodate the operating conditions, which is expected to reach least 24 months service life. The original manganese steel liner only had about 8 months liner life.1. IntroductionMineral processing is an essential operation for the development and utilization of mineral resources. The effective concentration of various useful minerals depends on sufficient liberation of the mineral particles in the ore. The crushing and grinding process such as ball milling are the most common way to achieve proper liberation size. Mill liner is an eternal topic for the operations, not only because it protects the equipment, but also affects the mill grinding efficiency and availability. In recent years, magnetic mill liners have been developed that can easily meet the production targets with numerous benefits, such as zero maintenance, reducing specific energy consumption and improving grinding efficiency."

Jan 1, 2016

By R. O. Loutfy, J. C. Withers

"Titanium powder is produced from a small fraction of sieved sponge, HDH of sponge or gas blown from a melt produced billet. Ore from foreign sources is chlorinated in a very high temperature fluid bed to make TiCl4, then vacuum distilled purified and then reduced to sponge by Kroll processing. Domestic ores of ilmenite or perovskite can be carbothermically reduced to Ti2OC which can be chlorinated at low temperatures of 250–400°C to produce TiCl4 which can be electrolyzed in a fused salt to Ti powder, or the Ti2OC used as an anode in electrolysis to produce Ti powder. The electrolysis process can be operated continuously to produce Ti powder at a lower cost than Kroll processed sponge including produce control size powder. Electrolysis processing was scaled up and operated at the commercial demonstration stage on a continued basis that verifies the potential of a low cost process to produce Ti powder.INTRODUCTIONTitanium and alloys of titanium powder have been elevated to strategic status resulting from a focus of producing meltless titanium components as well as a feed for additive manufacturing processing. However, the high cost of titanium powder has limited wide scale implementation of using titanium powder as a feed to any process to produce titanium components. Titanium powder free of alloying is available as sponge fines from the Kroll process as illustrated in Figure 1. Titanium alloy powder is much more expensive, also illustrated in Figure 1 produced from an alloy ingot or mil product as the feed and then transformed into powder by one of several melt form processes which accounts for the high cost of titanium alloy powder at approximately $60–150/lb. Ton lots of titanium alloy powder (i.e. Ti-6Al-4V) from one source is quoted at $120/lb. in the U.S. It appears that alloy powder production cost by current processing is not sensitive to volume."

Jan 1, 2016

By S. C. Ells

Introduction An investigation of the bituminous sands of Alberta was begun by the Mines Branch, Department of Mines, in 1913. This investigation was interrupted during the period 1916-19, but was resumed in 1920. Work completed in October 1924 has included detailed topographical surveys of extensive areas, examination and sampling of principal outcrops, the mining of trial shipments, laying of demonstration pavements, and a study of methods adapted to the recovery of hydrocarbons from the crude bituminous sand. Bituminous sand consists, for the most part, of clear quartz grains, cemented together by petroleum residuum or bitumen. In form the quartz grains are most irregular, varying from sharply angular to smooth, waterworn shapes. The bitumen has a specific gravity of 1.018 and has a penetration of 9.00 mm. (77° F. 100 grams 1 sec.). The percentage of bitumen associated with the sand varies from 5 to 25 per cent. A large tonnage is available in which the percentage of bitqmen is 15 per cent or over. Production Up to the present time, production has been restricted to requirements for experimental .and demonstration work. The total quantity shipped for such purposes has not exceeded 750 tons.

Jan 1, 1925

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019