Search Documents

By R. R. Potter

"New Brunswick became a separate province in 1784, shortly after the influx of a large number of Loyalists from the United States. Many of these people settled along the Saint John River, including the area of excellent farmland near the present town of Woodstock. There were indications that some of these early settlers recognized iron formations in the vicinity of Woodstock about 1820, however the nature of the deposits was not known until 1836 when Dr. C. T. Jackson, a geologist commissioned by the State of Maine, investigated the mineral potential of the area. Jackson(1) described the ""ore"" as compact red hematite yielding 44 per cent pure metallic iron, and suggested that sizable tonnages may be present. It was about this time that an extensive limonite deposit was found in north-central Maine, near Mt. Katahdin. Other iron depostis were found in the Nictaux area of Nova Scotia, and a few years later at Londonderry* (Fig. 1). In 1837, Richard Ketchum of Jacksonville, on whose land iron ores had been found, petitioned the provincial government to incorporate a company. After much study, the York and Carleton Mining Company Bill was passed on March 15, 184 7. Several other petitions were passed permitting the company to construct roads, obtain woodland, etc. (2) . The first blast furnace was erected in 1848 on the west bank of the Saint John River near the mouth of Lanes Creek."

Jan 1, 1999

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By M. P. Brameld, G. Archambault, R. H. McCorkell

"The rates. J. at which materials emit radon are of interest in studies of the sources of radon in mines. buildings. soils overburden and other places where it may indicate the location of ore or be a health hazard. Here J values were determined by measuring the radon concentrations by means of scintillation counters or alpha-particle track detectors in chambers in which specimens were sealed. Errors in the measurements due to leakage from the chambers. lack of secular equilibrium in the decay series of the radon measured, or the limited rate of diffusion of radon from powders or within the chambers were shown to be insignificant or could be corrected. Scintillation counter measurements are highly reproducible; track detector measurements also appear useable and may be made on many small samples using small, simple chambers. J measurements were made for uranium ores, drill cores, standard CANMET pulps. concrete and gypsum board. Powdering of ores had little effect on their J values.IntroductionIn the mining and mineral sciences, radon (222Rn) is of interest chiefly for two reasons: in geochemical exploration for mineral deposits its presence in soil. overburden and water in more than background concentrations may indicate the existence and locations of uranium deposits and, if present in sufficient concentrations, it is a possible health hazard in mines, mills and other places where people live and work. The latter aspect of radon's role has received considerable attention recently(1,2,3,4,5), and surveys of soil-gas radon concentrations have been used for some time in searches for uranium deposits(6,7,8,9,)."

Jan 1, 1981

By B. Coupal, F. D'Hennezel

Sorption measurements show that peat moss has much stronger affinity for oil than straw, which is currently used. Microscopic studies of peat moss show a highly porous and fibrous material, and this property, associated with the phenomenon of selective absorption, had been used to absorb oil. Laboratory experiments show that peat moss absorbs up to eight times its weight of oil. Field tests have proved that peat moss can be an effective absorbent and can be used on a large scale.

Jan 1, 1972

By D. Cruden

DISCODAT is a system of computer programs written for CANMET, Canadian Department of Energy, Mines and resources, to be used in analyzing geological data for rock slope design. The programs were written in Fortran IV for an IBM 360/67 computer. A program conditions field data from field forms for storage in a line file. Data may be selectively retrieved from the line file by a general retrieval program which uses a variety of relational operators. The retrieved data may be displayed as structural diagrams or histograms produced on a line printer or in a number of maps produced on a drum plotter. There is a logical sequence which leads to the characterization of those elements of the subfabrics of a rock mass which may be kinematically active. Structural domains within the rock mass can also be outlined by a procedure described as areal analysis. Costs for a complete analysis are usually substantially less than $l/discontinuity.

Jan 1, 1978

By Abdelhak Bentriou

The choice of tool for the first well of an oilfield or gasfield is an important factor, given that we will be drilling with the same type of tool for the entire phase and explains why we need to have another type for comparison based on the efficiency of the tool and its ability to crush the rock, and the wear of different types of tools. Development of theoretical and practical tests to determine the optimal regime for drilling is required to take into account the characteristics of rock layers crossed. Classification of boring tools is based on the geometry of the teeth and depends on the hardness, the abrasiveness of rocks as well as their hydraulic system, but it is better to classify them according to the working conditions with a coefficient designating a discriminant. This is called physical characteristic of the drilling tool. The goal is to designate each element of the tool by a coefficient. Results were obtained from laboratory tests. Modeling the initial rate of progress by different types of tools allowed us to determine an adequate mathematical model of the speed initial progress in clean conditions. Using experimental data and statistics we have established the mathematical model of the average speed of progress as a function of time. With these equations we can determine the wear evaluation and analysis of these factors as an approach to classification according to their characteristics. The main equations for the selection of drilling tools will be based on the optimization of drilling parameters for each type of tool. After analysis, we choose the tool that gives a better forward speed with an optimal load and axial rotation.

Aug 1, 2013

By M. Thérien, M. Rémillard

"Data from two industrial plants are treated by mass balance package BILMAT. The first application concerned a base metals/precious metals (PM) producer and the second, implementation of a hydrocyclone for the recovery of iron chips in the granite industry. Also LOTUS 123 software can easily be adapted for laboratory test mass balances using an IBM-PC computer. INTRODUCTIONThe present paper deals with two different BILMAT program applications. The first application concerns a copper-zinc-gol d-sil Yer producer based in North-western Quebec and the second, concerns the iriplementation of a hydrocyclone for the recovery of iron chips in Quebec granite company.Afterwards, we deal with some LOTUS 123 software applications for laboratory test mass balances using an IBM-PC.1. Base metal and P.M. producerNoranda Inc, Mattagami division, which operates mines in North Western Quebec, produces copper and zinc concentrates from a sulphide ore. Small amounts of gold (0,34 g/t) and silver (20 g/tl are present. At the time of the study, only 30% of the silver content was recovered in the copper concentrate. The main objective of this study is, to evaluate the metallurgical behaviour of silver in the flotation circuits, to increase its recovery in the copper concentrate and therefore to improve its final economic value. It is then worthwhile to identify the silver bearing minerals and to determine the critical flotation stages where they are lost. The methodology proposed is based on the coupling of a mineralogical study and a detailed mass balance ca1cu1ation in the flotation circuit performed using the BILMAT mass balance package (1, 2, 3).The results are discussed with respect to the distribution of silver in the circuit. The recoveries obtained at the various separation stages for the minerals present in the ore are also discussed."

Jan 1, 1987

By Thomas Hauquin, Olivier Deck, Yann Gunzburger

"In this study, 2D numerical modeling of a room-and-pillar mine is conducted along with the calculation of all terms of the mechanical energy balance. Simulations of different geometrical and geomechanical configurations are performed in order to investigate the conditions that favor a high seismic energy release (instability) during the excavation (removal) of one single pillar. At first, classical stressstrain simulations enable us to estimate the elastic and quasi-static response of the mine. Then, owing to the implementation of new functions in the modeling code, the seismic energy released when the pillar is removed is calculated. The obtained values are found to be in agreement with those calculated analytically using a modified energy balance based on the works by Cook (1967) and Salamon (1984).It is shown that the mine’s proneness to release large amounts of seismic energy, after sudden removal of one single pillar, mainly depends on three parameters: the initial extraction ratio of the mine, the depth of the exploited seam and the Young’s modulus of the surrounding rock mass compared to that of the ore. Moreover, it is pointed out that the magnitude of the seismic energy can be greater than that of the stored elastic energy, meaning that the dynamic (seismic) transient stresses should not be neglected when compared to the quasi-static stresses, particularly when trying to prevent the risk of rockburst and collapse in underground mines."

Jan 1, 2015

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

By C Kumar

Scaffolds are temporary structures built to facilitate construction activities on site. A considerable amount of resources are allocated to scaffolding on industrial projects. Variability in geometrical features and space accessibility of structures on industrial projects, in addition to involvement of different trades that share the use of scaffolds, requires an extensive understanding of scaffolding requirements. Hence, it?s important to plan and estimate scaffolding man-hour requirements for the different construction areas on an industrial site. Contributing factors involved in such estimates include the list of trades that work in a construction area, trade working hours, volume of work, geometry of equipment erected, etc. A simulation template for predicting scaffold erection man-hour values for individual construction areas in an industrial project was developed in Simphony 4.0. The template is based on mapping the geometry of equipment and other factors to man-hours of scaffold work. The template facilitates the use of distributions as inputs and produces a range estimate of scaffold man-hours. The mapping is based on a linear regression model derived from existing project data from PCL Industrial Management Inc. The template is being further developed to incorporate the ability to predict scaffold erection schedule and material requirements based on construction work areas or equipment lists of an industrial construction project.

Aug 1, 2013

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By Ken G. Kress

Syphons can be a simple, reliable and proven alternative to otherwise more complex pumping systems or low level outlet works. In a simple form they consist of a pipeline constructed over the top of an embankment or high topographic feature, connecting a source pond to a receiving pond or channel (see Photograph 1). The syphon action is initiated by removing air from the pipeline (priming) using simple devices which can be purchased ?off the shelf?. Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate or other devices. Repriming is not required even if the flow is stopped, provided the syphon is not drained. A limiting factor in considering a syphon as a design option is the maximum lift (i.e., vertical distance from source pond level to summit of syphon) which is approximately 9 metres, or less, dependent on syphon pipe features and site conditions. Pipeline syphons can be quickly constructed from readily available materials including steel, polyethylene and PVC pipe. They are particularly well suited to many of the unique conditions often encountered at minesites. This paper identifies situations that can sometimes be best resolved using pipeline syphons. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

May 1, 2001

By Robert B. Parsons

"One of the disadvantages of the federal government's idea of ""taxation by consultation"" is that it seems to take longer to enact new legislation. The proposed new rules for taxing automobile benefits is one example. Here is a ball which has been batted around between government and the public several times and still has not come down to earth. Fasten your seatbelts, there may be more to come. IntroductionThe draft legislation released on April 13 contains the details of the government's current proposals on car expenses and benefits. They differ significantly from the last announced position. Finance Minister Wilson has indicated that the release in draft form will provide an opportunity for the Commons Standing Committee on Finance and Economic Affairs (the Blenkarn committee) and other interested persons to comment before the legislation is introduced in Parliament. Accordingly, there may yet be revisions.Notwithstanding the prospect of further changes, the proposed rules generally come into force in 1988. While taxpayers may welcome some of these changes, particularly the increase in the tax-exempt allowance, many must be frustrated that, at this late date, the rules for the current taxation year are not yet finalized."

Jan 1, 1988

By V. Prodanovic, M. Militzer

Production of advanced linepipe steels with strength levels of 685MPa (100ksi) and higher requires excellent control of runout table cooling to produce the desired final fine-grained microstructures, which may include acicular ferrite. Cooling is exerted on the runout table by applying water jets onto the hot surface of the strip and heat is removed from the steel by forced convective boiling. The associated boiling mechanisms are complex and include film, transition and nucleate boiling. A pilot-scale runout table test rig has been built to systematically study boiling heat transfer from a moving steel plate by employing industrial scale headers. Experiments were conducted using test plates moving at speeds between 0.3 m/s and 1.4 m/s. The plates were cooled down from 850°C to temperatures below saturation by a single water jet supplied through an industrial size circular nozzle. Based on these experiments heat fluxes were determined and further used to develop improved runout table cooling models.

Jan 1, 2005

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By A. MacKinnon, P. W. Kingston, W. F. Caley

"Wollastonite (CaSiO3]) is experiencing increased usage in a variety of applications, such as fillers in paints, plastics and resins, as an extender to replace both non-fibrous and fibrous materials (e.g. asbestos), and in the glass and ceramics industries. Significant new deposits of wollastonite have been discovered in Marmora Township, about 175 km northeast of Toronto. The geological setting of these large-tonnage. High grade deposits has recently been investigated to assess the possibility of their development. A preliminary study of the chemistry, as well as the mineralogy of six occurrences is presented. Based upon this information, it is suggested that several of the deposits have an excellent development potential.INTRODUCTIONWollastonite is an anhydrous calcium metasilicate (CaSiO3), with a theoretical composition of 48.3% CaO and 51.7% SiO2; the calcium may be partially replaced by iron, manganese, magnesium, and strontium. Commonly associated minerals include diopside, tremolite, idocrase, grossularite andradite, quartz, and calcite. Wollastonite forms as a contact metamorphic mineral within impure limestone near intrusive bodies of granite, or other acidic rocks, as the result of metasomatism of calcareous sedimentary rocks, or by the crystallization of certain magmas (e.g. carbonautes). Generally, the reaction of calcite with silica to produce wollastonite occurs when siliceous hydrothermal fluids from a granitic intrusion or primary silica in the limestone/marble react with calcite in limestone at temperatures between 450°C and 600°C."

Jan 1, 1989

By Robert D. Brown

"Important tax changes, many of them of direct interest to the mining industry, were contained in the budgets brought down by federal and provincial finance ministers across Canada this spring. This month, Tax Notes presents a brief summary of important tax changes introduced at the federal and provincial levels in the last few months.IntroductionIn the March 1980 issue of the CIM Bulletin, Tax Notes surmised that the short-lived 1979 budget proposals of the former Conservative government offered a unique glimpse of budgetary changes that might be unfolded in 1980. Scene II of this ""now you see it-now you don't"" drama opened on April 21, 1980, when Finance Minister Allen MacEachen, in an ""economic statement""' reintroduced a selection of tax proposals taken from the ill-fated Conservative' budget of December 11, 1979, but refused to bring forward major new proposals in tax and finance.Mr. MacEachen proposed a 5% surtax on federal corporation income tax to apply in the 2 years from January 1, 1980 to December 31, 1981, as a slightly modified version of the same surtax proposed by former Finance Minister Crosbie in his December budget address. Mr. MacEachen also reintroduced a number of technical amendments which would affect the taxation of mining income in certain instances. In addition, a large number of other tax proposals suggested in the previous Conservative budget were also reintroduced, although there are some notable omissions."

Jan 1, 1980