Search Documents

By D. R. Reeves

This paper describes the geophysical Jogging of coal that is being carried out for the National Coal Board in the United Kingdom. An explanation of the technique is given and results are presented showing estimations of seam thickness to within ±0.5 in. and ash content to accuracies of ±2.5 per cent. The basic method of interpretation is outlined and some conclusions regarding the conditions of roof and floor material which may be deduced from the logs are explained. An indication of future developments in this field, including the identification of coal type and moisture content, is given.

Jan 1, 1971

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By M. H. Allan

SASKATCHEWAN POWER CORPORATION is a Provincial Crown Corporation responsible for the production transmission and distribution of electric power and natural gas in the Province of Saskatchewan. Through the electric power responsibility, we became interested in the coal reserves in Saskatchewan, which, although still somewhat of an "orphan fuel" in the early and mid 1950's, gave the promise of providing a low-cost source of energy for electric generation. Coal in Saskatchewan, a lignite with an "as-received" heating value of from 5000 to 6500 Btu's per lb and up to 40% moisture, was first recorded in 1853 . By the end of the 19th century, many small mines were in operation in the Estevan, Coronach and Shaunavon areas supplying local inhabitants with a cheap source of heat. These small mines, some of them prosperous, some of them not, continued operation right up to the late 1940's, when oil replaced coal in the market place. The year 1930, however, saw the introduction of the new technique of strip mining in the Estevan area. This technique revolutionized coal mining. It was now possible to use large machinery to uncover the coal and cast the overburden to one side instead of burrowing through thin seams of coal varying from 2 to 10 feet thick. The overburden cast aside by these large mechanical shovels, or later draglines, created heaps of spoil which at that time, during the depression, were a sure sign of prosperity and the welcome news that people had jobs. By the late 1940's, coal production had dropped off, but the spoil piles remained and were now labelled by some as "scars on the landscape", even though there had been some natural succession of grasses. In addition, some people had planted trees in experimental plots and even some aerial seeding had been done.

Jan 1, 1978

By C. J. Sullivan

Many metalliferous ?provinces are co-extensive with particular groups of sedimentary, volcanic, or :basic plutonic rocks. Deposits may be truly syngenetic (Rand, Rhodesia-Katanga, Mans-field, Blind River, White Pine); re-. concentrated by circulating waters (Colorado Plateau, Red Bed Coppers) ; or re-concentrated thermally during metamorphism and granitization (most uranium and lead-zinc provinces ?and some copper and gold provinces). Basalts may yield important cop-per provinces when folded and re-heated. Granitization of basalts which have not reached the chlorite-carbon-ate phase of metamorphism may produce copper provinces. If they reach ?the chlorite-carbonate stage, granitization may result in a gold province. Copper and copper-nickel provinces may result if gabbros are granitized, and a ?similar alteration of per-idotite may result in asbestos or nickel ores. Many similar associations are known. Granite is not a source of ore, but a result of heat. A classification of ?ore with respect to source rocks is of greater prospecting value than are classifications based on magmatic differentiation and hydrother-mal solution theories. Volcanic centres are important ore foci because the thermally unstable metallic sulphides may be concentrated here by a distillation process. The ores found in the hot spring deposits, viz., mercury, mercury sulphide, sulphur, and the compounds of ?antimony and arsenic, are not those which are soluble in water at low temperature (epithermal sub-division of hydrothermal class), abrut those which are unstable thermally at comparatively low temperatures . Water is one of the most common thermally unstable minerals, and generally accompanies the thermally activated ore-forming sulphides.

Jan 1, 1957

By S. Parkash, A. J. Szladow

Vigorous agitation of suspensions of coking coals in water (or light mineral oils) will often result in catast rophic loss of caking properties. It is shown that this deterioration is not a consequence of oxidation of the coals (by dissolved oxygen), but that it can be qualitatively connected with internal "solid-state" reactions which appear to derive their activation energies from cavitation of the liquid.

Jan 1, 1971

By Scott L. Ewart, William M. Bryden, Donald E. Wakefield

"Osler, Hoskin & Harcourt develops commentaries from time to time on topics of legal interest. These may deal with new legislation, changes or developments in government policy or recent judicial decisions of importance to its clients. The commentaries are, of necessity, general in nature. Because the law which they deal with is often new and untested, it is hard to arrive at precise statements of the way in which the principle s discussed in a commentary might be applied in specific circumstances. When further guidance is needed , consult a solicitor.The purpose of the Bill is to simplify, modernize and standardize the regulation of mineral exploration and development in Ontario. Many of the changes proposed by the Bill are of an administrative nature and move much of the detail with respect to staking, assessment work, prospecting work, surveys, quarry permits and leases contained in the existing Mining Act to the Regulations contemplated under the Bill.The Bill will undergo revision and be re-introduced and therefore it is not the intention of this present article to detail the specific changes contemplated by the Bill; however , its more significant changes are as follows:1. Provision is made for a lifetime prospector's licence with the elimination of annual renewals;2. Perimeter staking of a block o f claims is permitted to reduce the cost of staking;3. Assessment work requirements are expressed in term s of dollars spent rather than days worked;4. Persons doing exploratory work are required to furnish notice to owners of surface rights of intention to perform assessment work;5. Annual work summaries will be available to the industry to lessen duplication in exploration work;6. The option of continuing assessment work rather than applying for a lease is provided;"

Jan 1, 1984

By A. Sutherland Brown

"The Red Rose Mine is in the Rocher Deboule Range, 8 miles south of Hazelton. The mill camp (elevation 4,000 feet) is on Red Rose Creek, 11 miles by road from Skeena Crossing. The mine camp is one mile northeast and 1,600 feet above the mill camp on a spur of Red Rose Peak.The Red Rose mine was described in the Jubilee Volume, Structural Geology of Canadian Ore Deposits (Davis, pp. 129-131), but regional geology and mine development have progressed to a stage at which a more complete description is possible.The property was first located in 1912, and for the next 7 years was prospected actively for gold and copper on the southern extension of the Red Rose shear. Scheelite was first discovered in the vein in the northern part of the shear in 1923. The Consolidated Mining and Smelting Company of Canada, Limited optioned the property in 1939, and after a drilling program in 1940 the present mine development was initiated in the vein in the northern part of the shear. A 75-ton-per-day mill started operating early in 1942 and continued until 1943. The property was inactive until 195 l, when Western Tungsten Copper Mines Limited leased the property from The Consolidated Mining and Smelting Company of Canada, Limited. A mill, which later was enlarged to 140 tons per day, started operations at the end of 1951. The mine and mill were closed in December, 1954.The mine has twelve levels and sub1evels, and most of the workings are in the plane of the vein (see Figure 2a). The level interval is not constant, but between the lower four levels is 87 feet (100 feet in the plane of the vein). Access is provided by four adits; the 800 (elevation 5,659 feet), 600 (5,920 feet), 300 (6, 133 feet) and 200 levels (6,237 feet). The 600 level is the main haulage, and from it the ore is transported to the mill by aerial tram. From this level an inclined shaft extends in the vein to the lowest level (I, 100)."

Jan 1, 1949

By Daniel Murray

"ACCIDENT PREVENTION in and around coal mines presents many problems of a type which are not encountered in any other industry. This is particularly true of the coal mines in Nova Scotia, where the underground workings are very extensive and the area of exposure to workmen is very great.Roof conditions at the coal faces and in the waste change very rapidly, almost from hour to hour, and it is at these places that the greatest dangers exist and where most mine accidents occur. It is only natural, therefore, that our attention, as far as accident prevention is concerned, should be concentrated •at the coal faces and in the waste, especially in mines where the longwall system is used in the operation •of the seam.It has been said that no hard and fast rules can be set down for timbering at the coal faces and in the waste in the coal mines in this area. We do not subscribe to this theory, however, for the following reasons:On the longwall faces in No. 18 Colliery of the Dominion Coal Company, Limited, where the 'Dosco Miner' has been in operation and where there is a very rigid system of timbering and roof supports, which is strictly followed, only one compensable accident has occurred on those faces from May 2ndJ 1950, to the time of writing this paper, February 3rd, 1953.The 'Dosco Miner' has worked on four different longwall faces in this mine and has mined and loaded some hundreds of thousands of tons of coal."

Jan 1, 1953

By J. E. Gill

"THE YEAR 1959 appeared to be a good one in which to attempt a summary of progress in the location and study of sulphide deposits in Canada because a temporary surplus of metals caused prices to fall and many geologists who had been working like beavers were suddenly not so hard pressed. So it was •decided to arrange a Symposium. The response to the call for contributions was excellent and the result is the interesting collection of papers that follow.Activity in the search for massive sulphide deposits has never been as intense as in Canada since 1954. That was the year when the airborne electro-magnetometer first became generally available on a contract basis. These instruments work best on massive sulphide bodies, as do most of the ground electrical survey devices, so much of the new information relates to these. It was decided, therefore, to focus attention in the preparation of symposium papers on such masses. This served also to keep the survey within reasonable limits."

Jan 1, 1960

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

By R. L. Brown

The burning sulphide ores in the Sullivan Mine generate sulphur dioxide gases. This paper is concerned with a description of the environmental impact of SO2 on air quality in the mine and on the surface in the vicinity of the mine. As a result of surface caving, SO2 has been able to vent to surface and winds have carried it into one residential area of Kimberley. Monitoring practices are described.

Jan 1, 1977

By D. Mills, W. J. Brantina

"Mechanical and magnetic characteristics of ferromagnetic materials were investigated by a pulsed ultra-sonic technique. Two instruments, the Ultrasonic Attenuation Comparator (Sperry) and the standard type Reflectoscope (Sperry) were used for measurements of the attenuation of the ultrasonic pulse. The effects of elastic tensile and compressive stresses on the attenuation of annealed and cold worked material are described. In addition, the effects of plastic de-formation, relaxation and aging processes and different ultrasonic test frequencies are reported. The results for Armco iron, SAE 1020 steel, SAE 4340 steel and AISI 420 stainless steel are shown. Under the test conditions, the attenuation was found to be largely a sum of two components; a ""dislocation"" component associated with the losses accompanying the oscillations of dislocation line segments and a ""ferromagnetic"" component associated with the microeddy currents generated by magnetic domain wall oscillations. Either of these components might be dominant depending on the nature of the particular specimen and the test conditions. Finally, the possibilities of using ultrasonics in residual stress determinations, in fatigue studies and in the study of the ductile-brittle transition in ferrous materials, are briefly discussed."

Jan 1, 1960

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Mongolia is a country rich in rare earth resources. In the experiments carried out samples of the Mongolian ore were processed to obtain a lanthanide concentrate. The concentrate underwent hydrometallurgical processing. At the same time radioactive elements were removed. The lanthanides were obtained in the form of hydroxides that were further processed in order to get concentrated products. As a result cerium, lanthanum and neodymium-praseodymium concentrates were separated in the process. Also a concentrate of remaining elements: samarium, europium, gadolinium, terbium, dysprosium, holmium and erbium was obtained. INTRODUCTIONAccording to the assessment of the US Geological Survey, Mongolia possesses 16.77 % of the world total rare earth (RE) resources (Daly, 2011); that is the second largest RE reserve in the world, estimated to be 31 million tonnes in terms of rare earth oxides (REO). In the face of Chinese RE trade restrictions, Mongolia emerged as an important economical partner in mining and exploitation of these critical raw materials. This country is recognized as having more than five large RE deposits in the southern provinces. The most important are Lugeengol (Lugin Gol), Mushgia Khudag, Khotgor and Khalzan Buregtei (Eurasia, 2010). The Mongolian government has taken measures to facilitate western investments, nevertheless the country is economically dependent on China, the basic trading partner, particularly where exports are concerned.In the late 1970s Hydromet Kowary Enterprise, Poland, took up, along with the Wroclaw University of Technology, research and technological study on lanthanides recovery from raw materials of Vietnamese and Mongolian origin and from Indian monazite sands (Kowalczyk, 1990; Kowalczyk & Mazanek, 1987; 1990). For that purpose, a rare earth processing plant had been constructed with the capacity of about 10 t/year of hydroxide concentrate. The facility included several technological operations like grinding, flotation, hydroxide concentrate production in the hydrometallurgical processing, particular RE separation, and production of commercial products in form of CeO2, La2O3, Nd2O3, Pr2O3, and misch metal. Additionally work had been carried out in Kowary on the manufacture of yttrium and europium oxides of high purity, which were intended for color TV picture tube production in Poland."

Jan 1, 2012

By K. D. Watson

"THE Mindamar zinc-lead-copper mine, owned by Mindamar Metals Corporation Limited, is at Stirling in Richmond County, near the south-eastern shore of Cape Breton Island, Nova Scotia (Figure I). It is connected by several roads with the Canadian National railway at Sydney and St. Peters.The deposit is said to have been discovered around 1895 as an outcrop in the bed of Copper brook, but the details are obscure. Not until 1925, when it was optioned by American Cyanamid Company, was it developed underground. Between 1927 and 1938, the 1-nine was operated intermittently by The British Metal Corporation (Canada) Limited, and yielded approximately 200,000 tons of ore averaging about IO per cent zinc, 2 per cent lead, I per cent copper, and small quantities of silver and gold. In December 1950, Dome Exploration (Canada) Limited made an agreement with Mindamar Metaî Corporation Limited, which was exploring the old mine, to assume management and prepare the property for production. Production started in April 1952 with a new mill and a new four-compartment shaft, and between that time and the end of 1954 it has totalled 545,347 tons of ore averaging 5·89 per cent zinc, 1·35 per cent lead, 0·66 per cent copper, 0·032 oz. gold, and 2 151 oz. silver.The Mindamar orebodies are irregular lenses and large veins lying within a wide, almost vertical shear zone of remarkable persistency. The shear zone consists mainly of well-foliated sericite schist derived from siliceous siltstone, and it contains a vast amount of dolomite and magne-site of hydrothermal origin. Most of the ore is extremely fine-grained and some of the high-grade material has a conspicuous thinly layered structure. The metallic minerals, in order of decreasing abundance, are pyrite, sphalerite, chalcopyrite, galena, and tennantite; the gangue minerals, in the same order, are dolomite and magnesite, quartz, sericite, talc, chlorite, barite, albite, and alunite.The geological setting of the deposit is shown in Figure 2. Except along streams and lake shores, almost all of the bedrock is concealed by glacial drift. The group of rocks in which the deposit occurs consists principally of greywacke, siltstone, tuff, brecoia, and Javas, and has been correlated lithologically with the Bourinot group of Middle Cambrian age. A short distance west of the mine, these rocks are in contact along the Stirling fault with conglomerate, arkosic sandstone, and quartzite belonging to the Middle River group of Silurian or Devonian (?) age, which elsewhere in the area overlies the Bourinot group unconformably. The large bodies of granitic rocks in the region, and the large lenticular masses of diorite and quartz diorite associated with them, have been assigned by Weeks (5, pp. 68-69) to the Devonian."

Jan 1, 1949

By John Canterford

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15,000 t/a magnesium alloy production facility in Nanjing, China, Site construction commenced in February 2005 with installation of all major components completed by the end of October 2005, Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005, Since that time ramp-up to the name plate capacity has been undertaken, This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By A. B. Irwin

Abstract The techniques used in recognizing, recording, and interpreting structures in the Slocan sedimentary ceries in the West Kootenay district of B.C. are presented here in the hope that they will be of use to others working in complexly folded areas. The general pattern of folding in the Central Slocan area is obscured by lack of outcrop over a large part of the country, lack of marker horizons, local complexities of folding, and several systems of faulting. 1t was found necessary to observe and record in great detail all primary and secondary structural features and to analyse those observations on a statistical basis. The determination of bedding tops as well as bedding attitudes proved to be of fundamental importance in determining the pattern of folding. The interpretation of secondary linear and planar structures confirm:; this pattern. Accordingly, the thickness of the Slocan sedimentary series is computed to be several times that formerly postulated. Introduction The data upon which this paper is based were collected largely during the field seasons of 1947 and 1948 when the writer was employed by the British Columbia Department of Mines on detailed mapping in the Slocan mining camp. Additional observations were made by the writer during 1950 when engaged in property examinations for the Geological Survey of Canada. This presentation is largely a condensation of part of a more comprehensive thesis (5) and is restricted to observations and conclusions pertaining to the mapping of complex folds, stripped of any hypothetical discussion. Except for some unique occurrences of primary structures, there are no features or techniques described here which are not presented in standard textbooks on structural geology. It is felt that the major contribution of this paper is the method used in applying these standard techniques to a specific field problem and in interpreting the results.

Jan 1, 1951

By T. Richard Davies

This paper primarily deals with the application of wearfacing materials and their role within a well-established preventive maintenance welding program. Some examples are shown, as well as a synopsis of possible benefits and a compendium of methods and materials.

Jan 1, 1979

By Daniel Torres Espinoza, Jose Pinedo

"Ventilation is a vital service in underground mines, required to provide fresh air to the work force and dilute diesel equipment gases (CO, NOx) and diesel particulate matters (DPM). At a Mexican precious metal mine in the state of Chihuahua there is a VOD system implemented using Howden’s control and monitoring system and a state of the art tagging and tracking technology. The JM zone of the mine is ventilated using a push and pull system, using automated regulators on each level to control the air going in and out of the levels. The implementation of advanced control strategies using Howden’s VentSim™CONTROL allows the mine to generate significant savings and increase health and safety of the workers.INTRODUCTIONIn underground mines, ventilation is a requirement in order to maintain the fresh air needed for personnel and equipment. Ventilation regulations dictate the amount of air required underground to carry out day to day operations by limiting the exposure that workers have to toxic gases and other pollutants. Regulations for required airflow in underground operations for diesel pollutants are generally provided on vehicle rated brake horsepower, in Mexico the requirement is 75 cfm/bhp. In underground mines, ventilation services can account to up to 75% of the mine’s energy consumption, and it is very common for fans to operate all the time because of a lack of control infrastructure for the ventilation system. By the implementation of a Ventilation On Demand (VOD) system a mine can reduce this consumption with different control strategies. The main infrastructure required to implement this system consists of remote control of ventilation infrastructure (fans and regulators), a communication network between throughout the mine with the surface and a tracking system for personnel and diesel equipment. Software is required to determine fresh air requirements based on the tracking system data and then send the control commands to the different ventilation infrastructure. In 2015, San Julian Mine acquired Howden’s VentSim™CONTROL (formally SmartEXEC) and the hardware solution to deploy a VOD system at their operation. The VOD system and Fresnillo plc’s San Julian Mine in Chihuahua, Mexico, consists of control of 10 surface exhaust fans, 2 surface intake fans, and 12 underground automated regulators. It also includes the monitoring of 46 flow sensors, 28 CO sensors, 28 NO?? sensors and 42 temperature and humidity sensors, approximately 500 personnel tags, approximately 220 vehicle tracking tags with diesel status (ON or OFF) and approximately 250 tracking zones. This paper discusses the control strategies that have been implemented at San Julian Mine since the system was commissioned and the next steps that will be taken at the mine with the system as they test different level on VOD."

Jan 1, 2019

By B. K. Mishra, P. Patnaik, B. C. Tripathy, I. N. Bhattacharya

Cobalt is an essential metal considering its numerous industrial applications. The demand for the metal is increasing due to its wide range of use in, for example, rechargeable batteries and as an alloying element in super alloys. Cost effective production of Co is critical. Electrowinning from aqueous sulphate solutions is the preferred technology available for the production of Co. Attempts are being made to produce uniform, smooth and bright deposits of cobalt metal. Use of organic additives in the electrolytic bath improves current efficiency and deposit morphology of the metal. We investigated the effect of quaternary amines TEABr, TPABr and TBABr during cobalt electrowinning from aqueous sulphate solutions. Among the additives studied, TEABr yielded the best results. Smooth and bright deposits of cobalt were obtained at low concentration of TEABr (10 mg/L) maintaining a very high current efficiency of 99.6%. X-ray crystallography indicated that (100) is the most preferred plane of crystal growth.

Jan 1, 2014