Search Documents

Cessation of mining on the Bendigo goldfield makes it evident that, as the older generation fades away, knowledge of the famous Bendigo saddle reefs will be limited in the future by their written records. It is important therefore that the summarised account by D. E. Thomas (1953) in the Geology of Australian Ore Deposits should not be misleading. Fig. 6 in this article is stated to portray a cross section and longitudinal section through a series of gold shoots in the Garden Gully 300 ft. reef. The gold shoot along the capof the saddle reef is represented as extending down the east leg in a series of prongs, with the tips of the prongs about 50 ft. apart. It is the purpose of this note to indicate that this illustration can be suspected to be a diagram of the old stopes instead of a diagram of the distribution of gold in the quartz.The original sketches of Figs. 6 and 7 in Thomas' account were extracted, I believe, from the field note books of H. S. Whitelaw, years after his death in the late twenties. Whitelaw was stationed in the Bendigo office of the Geological Survey of Victoria, carrying out geological surveys of the Bendigo mines. He was there for many years before the Gold Research committee started its investigations in 1916 and he was acutely aware of the problem attached to the distribution of gold in the reefs. He had felt concern that manyauriferous reefs were being mined without adequate study and record and he decided, as he expressed it to me, to pick up what he could as he went along. There can be little doubt that the diagrams of Figs. 6 and 7 are products of this resolve.Opportunities to investigate gold occurrences at Bendigo were limited before 1916 because the field was operated by Manuscript received at The Institute 18th November, 1960.

Jan 1, 1961

By Schlanger H. P

A theoretical model for gas outbursts in underground coal mines is as follows. An outburst is the structural failure ofcoal due to excess stress resulting from body forces caused by gas pressure gradients. These body forces influence the stability of a mine face in the same manner that gravitational body forces affect the stability of the roof of a mine. The magnitude ofthese body forces can be appreciated when it is realized that for an average density coal, the gravitational body force is equal in magnitude to the force from a gas flow with a pressure gradient of 14 kPa m-I. Gas pressure gradients and the resultant stresses within a seam can be calculated with numerical methods. Thus, providing the necessary parameters can be measured or estimated, in principle the theory can be applied to compare the outburst risk of various mining arrangements.

Jan 1, 1985

Interest in industrial minerals in recent years has increased to such an extent that it has taken them into the mainstream of the Australian mineral industry. Notwithstanding that time series data on the values of production, exports, and imports show that industrial minerals are overshadowed by metals and energy minerals, their contribution to the national economy is important and more significant than would seem to be indicated by the statistics. Whereas the ex mine value of metals generally includes some processing (at least to a concentrate stage), most industrial minerals are valued at little more than their extraction cost, in addition to which such costs are generally low because most industrial minerals are exploited in low-cost surface operations. Consequently, values of mine production of metals and industrial minerals are not strictly comparable in that values of mine production of metals tend to be overstated Short term growth of the industrial minerals sector is assured because of several new projects already commissioned but not yet reflected in the statistics. Longer term growth is also assured, based on various other major projects that are likely to come on stream in the early to mid 1990s.

Jan 1, 1989

With the exhaustion of orebodies close to the main haulage shaft of the Emperor mine, an increased rate of development, aimed at earlier investigation of values disclosed by exploration drill holes has been attained with an overall reduction in unit costs.This paper describes the techniques used in rates of advance up to and exceeding 1,000 ft per 28-day period.

Jan 1, 1966

Suddenly, mining has been thrust into the limelight. It has a large image that casts its shadow over New Zealand. Is it any wonder that resistance has heightened and that an almost unprepared populous is currently struggling to protect the very land they hold dear. Next to the atomic bomb, mining has the demonstrated power to massively change the land and its side effects can pollute many miles beyond the operation. During the past year, New Zealand concern over the possible effects of the mining proposals has become acute. This was specially so in the areas of special environmental quality, such as the Coromandel, and here a very unhappy situation has arisen.

Jan 1, 1981

By B Belle

In a predrained gassy coalmine, ventilation control plays a secondary role to the longwall (LW) goaf drainage systems to safely manage panel return gas levels. Typically, the LW specific gas emission (SGE) estimation models provide anticipated goaf gas emissions and arriving at required gas drainage capacity for various coal production scenarios. A study comparing the various LW goaf gas hole spacing patterns with weekly production rates of up to 270 kt/w of an operating mine with high SGE rates (~20 m3/t) was carried out. The goaf capture efficiency of LW panels ranged from 64 per cent to 85 per cent. For the first time, gas content of upper seam data post LW retreat were used to verify the current SGE prediction models. This study has shown that an average of 50 m goaf spacing is optimal for management of high production retreat gassy LW panels in presence of multiple upper and lower seams with gas emission zone influence reaching up to 200 m above workings. Due to the horizontal stress direction related geotechnical issues, goaf hole failures just behind the LW face is a recurring challenge resulting in significant and immediate increase in LW panel return gas levels. This paper highlights the shortcomings of current SGE prediction models for goaf gas estimation, and evolution of 50 m goaf hole spacing embedded in design process in managing the LW tailgate gas levels.CITATION:Belle, B, 2017. Optimal goaf hole spacing in high production gassy Australian longwall mines – operational experiences, in Proceedings Australian Mine Vent Conference 2017, pp 15–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The morphological changes that gold undergoes during transport in gravel-bed rivers are a function of transport distance in particular, as well as bedload material, river gradient and velocity, and bed roughness. Gold size, shape and outline are modified by abrasion, flattening, folding and breakage during transport. The resultant morphological characteristics can be used to predict source types, source location and transport distance, as well as the origin and dispersal patterns of gold in ancient placers where the transport history is unknown.

Jan 1, 1998

Process Simulation and Plant Design of a Mineral Selective Magnetising Flash Roasting Plant Using Neutrons

Sep 13, 2010

By Mech B

This paper gives a general description of mining practice at The Zinc Corporation Ltd., Broken Hill, New South Wales.The basic mining methods are those which have been common in Broken Hill for many years and have been well described in previous Proceedings. The main object of this paper is to indicate developments which have occurred in recent years and to describe changes in layout, mining methods and equipment which are taking place at present.The following headings have been adopted: History Geology and general characteristics of the orebodies, Geology, The lead lode, The zinc lode, General characteristics, Ore reserves, General mining method, Exploration and diamond drilling, Shafts and shaft sinking, Main shaft, Old main shaft, Block 5 shaft, New upcast airway, Development, Level interval, Level layout, Driving and crosscutting, Winzing, Rising, and Stope preparation.

Jan 1, 1946

The reconstruction of the world after the present war must inevitably be profoundly influenced by the rise and progress of New China.The principle of Chinese mathrity has been admitted by Great Britain and the United States by their abjuration of extra-territorial tights, and by the withdrawal of the Maritime Customs Administration. The United States admits equality by her declaration that Chinese are eligible for American citizenship, and the reaction to this will be swift enmity to such peoples as may impose humiliating restrictions upon Chinese citizens.Finally, the decisions of the Moscow Conference and the recent meeting of National leaders in Cairo give partnership rights to this new State in post-war reconstruction, and open the way for a rapid realization of her destiny.It seems certain that China, if so she wills, can become, within a generation or so, one of the considerable forces of the world. The toad she wiII follow will be lighted by her own inherent and intrinsic genius. Her speed of progress can no longer be forcibly influenced by other nations and the attitude towards her of somewhat contemptuous patronage hitherto adopted by the European communities bordering the Pacific Ocean must be radically modified.It is doubtful whether the European will ever reach full understanding of Chinese mentality. The Chinese "way of life" since the dawn of her civilization has been totally divergent from that of the European, but the enormous potential strength, due to the simplicity of their requirements and their steadfast industry, is a function of that "way of life." On the other hand the trend of reorganization must obviously be towards Western standards; and a wide knowledge of the potential strength of the Chinese is possible and will be essential in our post-war world. The following, necessarily inadequate, notes are therefore offered, as an indication of the obstacles to be overcome and the capacity of the Chinese executives and operatives to overcome them.For 'thirteen centuries the political and social structure of China proper (ie, excluding Mongolia, Manchuria and Tibet) has been rigidly shaped by the philosophy of Lao Tze and the ethics' of Confucius. This Taoism, which is described as the "way of harmony" with its three jewels of character, gentleness, economy and humility, advocates the minimum of social, economic and political organization and still gives the key to the Chinese character.The Mongol and Manchu conquests of the 12th and 17th centuries, respectively, could hardly be dignified with the name of war, but the superior intelligence and harder mentality of the unwarlike Chinese finally absorbed...

Jan 1, 1944

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

The demand for gallium has increased significantly over the last few decades due to the expanding use of Ga compounds in the electronics industry. Because it is widely dispersed and rarely found naturally in concentrations greater than 0.1%, Ga is expensive (approximately US$500/kg) and difficult to produce in large quantities.   A previous study of metals in geothermal systems reported significant quantities of Ga present in the muds on the northeast margin of Lake Rotokawa, an acidic lake associated with a high-temperature geothermal field situated in the Taupo Volcanic Zone of New Zealand. Similar muds are present in many other geothermal fields in the zone, suggesting that geothermal muds could be a commercial source ofGa.

Jan 1, 1994

The following paper describes the refining practice for the production of lead, silver and gold at the works of The Broken Hill Associated Smelters Pty. Ltd., Port Pirie, South Australia.The refinery is situated on the wharf frontage and is built parallel with it. The refinery occupies an area of approximately 3380 square yards. (Fig. 8)There are two buildings, one containing the softening and de-silverising sections, measuring 225 ft. x 57t ft., while the other building, which measures 225 ft. x 90 ft. covers the de-zincing, lead moulding, retorting, cupellation, and dore parting sections. (Fig. 1)The retorting, cupellation, and dore parting sections are completely isolated from the rest of the plant by strong small-mesh wire gratings welded to steel uprights. The dore parting plant and generator room are further isolated by a brick wall, built up to the roof. The two main buildings are steel structures, with outer walls and roof of "Robertson" corrugated sheeting; the side and end walls are open for some distance above the ground, and this, coupled with the high roof which is 50 ft. from ground level, ensures the free access of air and light. Conditions are such that operators work in a clear atmosphere.

Jan 1, 1937

Valuable Components Recovery from Lead-Zinc Metallurgical Slag

Sep 13, 2010

A Sun SPARCstation based computer network is utilised to store and process mining data at the Macraes Gold Mine. Techbase and Medsystem software running on the SunOS unix platform is used to generate all data plans, sections and other design data required on a daily basis to run the mining operation. The Macraes site is regarded as a fully integrated site where all geological, grade control, exploration, orebody modelling, resource estimation, pit optimisation and mine design is undertaken on site by MacraesÆ professional staff. The methodologies employed are regarded as æstate-of-the-artÆ where computerisation allows the rapid and efficient evaluation of large quantities of mining data by a handful of professional personnel. Ore reserves are estimated using an indicator kriging method and roving cone pit optimisation, a complex process that would not have been achievable in pre-computing days.

Jan 1, 1992

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99· 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The mineral processing industry is in boom times. The focus on mill availability and therefore profitability has never been greater, as grinding mill maintenance often dictates the entire plant shut down duration. Advances in mill systemsÆ quality and reliability and the faster, safer relining afforded by RMEÆs Mill Relining Systems have significantly enhanced grinding plant availability and utilisation. Yet relining performance is still affected by the design and planning by a team of stakeholders long before the maintenance team set foot in the mill. For a greenfield grinding plant project, these team players include: 1. project owner, 2. project manager, 3. mill supplier, 4. liner supplier, 5. plant operating personnel, 6. plant maintenance personnel, 7. mill relining crew, and  8. mill reline system supplier (RME). The complex and sometimes competing design demands of mill construction and operation together with the pressure of tight timelines can result in even simple maintenance requirements being overlooked let alone optimising plant design and planning for maintenance. This paper identifies all the involved stakeholders in an effective mill relining 'team' and gives principles and considerations for each to more effectively achieve the goals within their vital roles. This paper is aimed to be a practical guide for grinding mill designers and planners to more fully exploit the advances in Mill Relining Systems and improve their mill profitability.

Jan 1, 2008

By K Lownie, R Sani, A Sianturi

Part of the PT Freeport Indonesia (PTFI) mine production is in the process of transitioning from the deep ore zone (DOZ) mine to the deep mill level zone (DMLZ) mine. The DMLZ mine is the next lift in the caving series and lies 500 m below the current DOZ footprint.In order to reduce the need for a very expensive additional ventilation system for the DMLZ mine, it was decided to reconfigure some infrastructure and upgrade the performance of the three existing DOZ mixed flow ventilation fans in situ, reducing the new fans required to two. This was far less costly than providing complete new installations.These fans are installed in individual underground chambers in DOZ mine exhaust drifts and connected to the DMLZ mine exhaust drifts system in 7 m × 7 m airways size, through sets of 6 m diameter by 500 m high raises.The upgrade process involved replacement of motors, fan shafts and bearings. The existing 1600 kW DOZ mixed flow fans are 3500 mm diameter and operate at a speed of 595 rev/min and were originally designed to deliver 390 m3/s at 3.3 kPa. Efficiency optimisation may be required at a later date.The upgraded DMLZ fans are required to deliver 425 m3/s at 3.7 kPa and it was necessary to increase in motor size and speed to 2200 kW at 710 rev/min. This paper will discuss the fan upgrade project and in particular the integration of an unusual ventilation system, which is based on the semi parallel operation of multiple large fans.CITATION:Sani, R, Sianturi, A and Lownie, K, 2017. Operation of deep mill level zone mixed flow fans after the first fan upgrade – a parallel fans case study, in Proceedings Australian Mine Vent Conference 2017, pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

As in other countries, gold mining inNew Zealand has been cyclic in character. Looking at these cycles may provide insights as to what may occur in the future and that is the basis for this study.   New Zealand has experienced four gold mining cycles. The first began in 1857, peaked in 1866 and terminated in 1890. This cycle was characterised by alluvial gold mining by individuals and small groups. This is referred to as the Labour Led cycle. The second cycle began in 1890 and reached its peak in 1906 and terminated in 1929. This cycle was characterised by the use of dredges in alluvial gold mining and was also the peak of hard rock mining. This cycle is referred to as the Technology Led Cycle. The third cycle peaked in 1940. This cycle was far less significant than the previous cycles, arising out of the depression when the unemployed embarked on small scale alluvial mining. This overprinted the continuing decline that occurred after 1906. This cycle is here referred to as the Depression Overprint Cycle.   The fourth cycle began in 1984 when production began to climb rapidly from a very low base. The growth in production was spurred by rising gold prices in the early 1980s resulting in relatively low grade gold-bearing alluvial ground becoming economic. But in the 1990s, production from the new hardrock mines in Coromandel and Otago has overshadowed alluvial production. This cycle is here referred to as the Price Led cycle.   What are the future prospects for gold in New Zealand? Although there are many factors involved, this will be largely determined by two factors; firstly, continued access to prospective gold-bearing properties, and secondly, the price of gold. Based on these factors, three future industry scenarios have been developed. The first of these is industry collapse, in which access to prospective property is constrained and prices mayor may not weaken. The second is industry consolidation, in which the available ground is accumulated by a small number of large companies who can use economies of scale to weather price fluctuations. The third scenario is industry growth, in which access to prospective ground is constrained in environmentally sensitive areas but is otherwise relatively unconstrained. Efficient companies are allowed to work in a policy and economic framework that allows them to make a major contribution to the economy.   While the industry cannot control these critical factors, a good knowledge of the positive role gold mining could play in the future economy may provide a framework by which the access issue, in particular, may be addressed from a balanced perspective.

Jan 1, 1994