Search Documents

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

According to the temporal and spatial distribution of regional metallogenesis, the Pacific Rim can be divided into four global metallogenetic systems. The Asia-Australia W-Sn metallogenetic belt is the typical representative of intracontinen- tal metallogenetic systems. This belt resulted from Mesozoic and partly pre-Mesozoic tectonic magmatism, mainly re- lated to S-type granite of crustal source, that was generated by collisional orogeny combined with oceanic subduction in intracontinental and continental margin settings. Based on the concept of metallogenetic series, there is a group of min- eralised ore types showing a definite spatial and temporal distribution from endogenetic to exogenetic. These metalloge- netic series are widely distributed in the Asia-Australia W-Sn metallogenetic belt, and are well developed in Southeast China. Five metallogenetic series and two petro-minerogenesis evolution models have been established according to their tectonic settings, various types of granitoids and metallogenetic evolution.

Jan 1, 1995

THIS paper is not intended to be more than a mere outline of the economic geology of Tasmania. It is desired to present in a condensed form the present state of our knowledge in regard to the distribution of the ore, coal, and oil-shale deposits of Tasmania in time and space.Tasmania is exceptionally well endowed with mineral wealth, particularly in the north-western and western districts. In the enthusiasm resulting from the first discoveries of mineral deposits at a great number of localities in those districts, it became a generally accepted belief that the whole of that portion of Tasmania constituted a continuous metalliferous province. As geological research in these, areas has progressed, however, it has become increasingly clear that ore-deposition has been confined on an economic scale to definite well-defined areas or belts which have a genetic relationship to certain tectonic and petrologic phases of the general geology. These areas or belts have recently been defined by the writer, and...

Jan 1, 1923

We often read and hear, especially in the United States, that we are running out of critical metals. These are vague forebodings of stagna- tion or winding down of our civilization. Our technological progress has been rapid in the last 50 years and is still advancing at an accelerated rate, and predictions of its long-term impact on consumption and production of metals are more hazardous than ever in the light of the great economic and political shifts that are bound to continue. There are many factors that will have a hardly predictable but profound effect on pro- duction and consumption of metals over a time span of, say, 25 years. Among such factors are recycling, substitution, availability of capital, direct involvement of governments in financing and production, and the capability of producing much lower grade ores at possibly much higher prices relative to costs in the event of scarcity. I must state at the outset that my discussion of this topic does not take into account the role that deep-sea nodules containing copper, nickel, cobalt, and manganese may play, because I don't believe production from these deposits will be of much significance within the 25 year span I will be discussing.

Jan 1, 1978

The Olympic Dam Project constitutes a major resource of Copper and Uranium and has been under intensive evaluation since the discovery in 1975.A 500 metre deep rectangular shaft has been sunk into the deposit and this has been followed by 8400 metres of level, incline and decline development. 5 surface ventilation raises have also been constructed.Large scale trackless equipment is used to carry out the development, and productivity statistics are given.The paper describes the functionalised system used in the development program and discusses the maintenance support, and services required to carry out these works.The objectives of the Exploration Development program and the satisfactory results obtained from this work are also discussed.

Jan 1, 1985

The Mount Lyell Company's concentrating mill is situated about a quarter of a mile westward of the portal of the North Lyell tunnel, which serves the North Lyell, Royal Tharsis and Crown Lyell mines, being on the 1100-ft. level of the first named. The Comstock mine is connected with the tram system at this level by five and a half miles of steam tramway, two-foot gauge being standard throughout.The plant is well placed with regard to all essential services and has an excellent water-supply from a series of three dams on the West Queen river.MILLING ORESThe mill feed is a mixture of the outputs from the foUr mines mentioned, each of which has its characteristic ore, but, generally speaking, about half of the ore consists of siliceous schists and the other half of hard grey quartzite. The schisty ores are easy to crush, but, on grinding, while the schist slimes readily, the quartz granules are hard, resulting in the handling of heavy loads on the secondary classifiers. The quartzite ores are both hard to crush and difficultto grind.The principal sulphide materials are bornite, chalcopyrite, and pyrite, chalcopyrite being the main copper-bearing mineral.The crystallization is coarse in the schisty ores, but it has been shown that even the 200 mesh (Tyler) material contains included sulphide particles. At the present time the sizing of the final tailing averages 80% through 200 mesh.

Jan 1, 1932

The Mt Keith Operation, 90 kilometres north of Leinster in the north-eastern Goldfields of Western Australia, was commissioned in October 1994. Based on a large tonnage, low-grade nickel sulphide orebody the plant was designed to produce 28 000 tonnes of nickel in a high-grade 20 per cent nickel concentrate. Following a successful and rapid start-up the operation is currently expanding to a throughput of ten million tonnes per annum (mtpa) ore and an annual production of 42 000 tonnes of nickel. This paper provides an overview of the Mt Keith Operation from commissioning to its present operation and Expansion.

Jan 1, 1996

By G Kluck, N Stoitis, D R. Seaman, R A. Lauten

The presence of clays, in particular clay slime, may complicate many mining operations. Clay slime particles may possess a negative or positive charge depending upon the pH in the process and their presence may lead to reduced recoveries in flotation processes. It is assumed that slime particles may adsorb onto the surfaces of the minerals to be floated and by doing so, reducing the efficacy of the flotation chemicals. In this work it is shown that addition of a small amount of dispersant, either a polyacrylic acid or an anionic polyphenolic polymer, increases the recovery of copper and gold, both in laboratory trials and in plant testing of an ore with high clay content. Measurements of adsorption isotherms reveal that the tested dispersants show preferential adsorption towards the clay minerals present, suggesting that the improved recovery upon dispersant addition occurs by prevention of attachment of clay slime particles onto primarily chalcocite but also chalcopyrite.CITATION:Seaman, D R, Lauten, R A, Kluck, G and Stoitis, N, 2012. Usage of anionic dispersants to reduce the impact of clay particles in flotation of copper and gold at the Telfer Mine, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Clark I, Stockton N, Warren L

Nickel flotation circuits currently experience difficulties in recovering fine particles of pentlandite less than ten microns. By agglomerating these particles using shear-flocculation it is hoped to improve the recovery of these fine particles. A sample of massive sulphide ore from the Kambalda region was separated using magnetic separation to obtain a high grade pentlandite concentrate (> 90 per cent). This was finely ground to produce a sample with particles of 50 per cent minus 10 um in size. This sample was then shear-flocculated using a variety of reagents, including xanthates, dithiophosphate and mercaptobenzothiazole (MBT). The effects of reagent type and concentration, conditioning time, impeller speed and type, and pulp density were studied. Froth flotation tests were also conducted on the shear flocculated pulps to compare the effects of xanthate and MBT on the recovery of pentlandite.

Jan 1, 1992

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

By G J. Corbett

Magmatic-related low sulfidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.   Low sulphidation systems in the south-west Pacific region exhibit a vertical zonation in deposit types: from porphyry copper-gold at deep levels, quartz-sulfide-gold at mesothermal to deep epithermal levels, carbonate-base metal gold at mainly epithermal levels, and epithermal quartz silver-gold at shallow levels. It is interpreted that the characteristics of each of these styles of deposits is produced by mixing with circulating waters of different physio-chemical compositions.

Jan 1, 1995

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

By Woodcock JT

This paper reviews the chemistry of flotation pulps with the aim of gaining a better understanding of the effect of chemical environment in flotation and ap- plying the knowledge to improving the con- trol of reagent additions. Theories of flotation are considered briefly, but they are only of limited help in specifying an appropriate chemical environment and in establishing control techniques. The chemical nature of flotation pulps is reviewed. Four distinct phases are present - solids, an aqueous liquor con- taining many dissolved reactive sub- stances, organic liquids, and gases. All of these vary in many ways and interact with each other. It has now been estab- lished that there are many previously- unsuspected materials present in plant pulps that can or might affect flotation. Concentration profiles of selected para- meters in operating plants are given to show some typical changes that occur. Recent advances in collector chemistry, especially that of xanthate and related species, are reviewed. Modes of decompo- sition and/or formation in pulps of xan- thate, dixanthogen, perxanthate, xanthyl thiosulphate, and monothiocarbonate are reviewed, and their W absorption spectra are compared. Some relevant information on dithiophosphates, mercaptobenzothia- zole, and thionocarbamate is summarized, and some speculative comments are made about reactions of these collectors.

Jan 1, 1984

JUDGING from the attitude of past and present Parliaments in Australia, it is a' reasonable assumption that encouragement of the principal industries has been adopted as a main principle in the government of the country, but while in most cases bonuses, subsidies, and other means have been proved successful and become recognized as established methods in the case of mining, which is undoubtedly one of the most important industries, the question is complicated by difference of conditions and variable quantities, and it can scarcely be said that any system has been proved generally successful. Indeed, it would not be a very extravagant statement to assert that problems connected with affording direct monetary assistance in aid of mining development, and at the same time devising a system adaptable to the varying conditions to be met, are, in every State of the Oommonwealth, matters continually exercising the minds of those concerned in providing and ailocating such assistance ie Parliament on the one hand, and the Department of Mines on the other.True, there are methods in vogue of granting State assistance to the mining industry which have undoubtedly been successful, but it is in most cases questionable whether the beneficial results following successful expenditure in one direction have compensated.

Jan 1, 1911

By G Ride

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in arid areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1971

The kinetics of desorption of nitrogen from molten iron were investigated using the electromagnetic levitation technique. The respective influences of gas flow rate and surface active element (S) were examined. A second order behaviour with respect to the nitrogen concentration in the melt prevailed at all experimental conditions. Sulphur had a marked inhibiting effect on the desorption rate. The experimental results on the rates of nitrogen desorption have been interpreted with the aid of a reaction mechanism consisting of a sequence of elementary steps.

Jan 1, 1991

This paper records the observations of faulting in the Black Star mine workings. By classifying the faults into two groups, i.e., strike faults and transverse faults, and by pointing out the differences between the groups and their effects on the silver-lead-zinc orebodies, a time relationship between the two groups of faults and the sulphide mineralisation is suggested.GENERAL GEOLOGY AND MINERALISATIONFolding and faulting are closely related to the mineralisation in the shales by silver-lead-zinc and iron sulphides.Commonly the various sulphides are fine-grained and closely associated with one another. However, exceptions do occur locally, where massive coarse galena, sphalerite, pyrite, and to a lesser extent chalcopyrite, have been observed singly or closely associated one with the other.In the main, the sulphide mineralisation forming the orebodies occurs as replacement of, and infilling along, the sheared bedding planes of the finely bedded shale host rock.The shales in general strike north-south with an average dip to 60° to the west; strong shearing along the bedding planes is evidenced by much slickensiding and slaty cleavage.Sequences of finely bedded shales of varying stratigraphic thicknesses alternate with very. massive beds, and it is in the more highly sheared thinner beds that the greatest concentration of sulphides occurs. The unmineraIised massive beds of shale, 11 in. up to 12 in. in thickness, occur singly or in groups between, and to a lesser extent. within, the orebodies. The massive beds resisted sulphide replacement and impart to the orebodies a most prominent banded structure.

Jan 1, 1953

Material hardness and environmental factors can limit or restrict conventional blasting techniques and this has led to advancements in the performance and efficiency of ripping. Not all materials can be ripped, however today's technology and experience can help make a reasonable prediction. A ripping versus blasting decision will depend on the total volume of material to be moved, the production capabilities and costs of the ripping tractor(s) and on the size and relative efficiency of drilling and Blasting.

Jan 1, 1995

Teller Underground Mine was established to extract ore from the Middle Vale Reef located on the eastern flank of Telfer Main Dome.The mine is located below a 150 m deep open pit operation. The ore body is shallow dipping highly structured, and is a main aquifer in quite difficult ground conditions.In respect of these conditions it was determined to access the orebody using an adaptation of coal mining and hard rock mining methods, with support being achieved using a combination of island pillars, rock bolts and timber stalls.The paper will describe these methods in more detail, then discuss the successes and failures of these methods when put into practice. As well, it will detail several factors whose influences were found to be greater than previously expected and stress the importance of good geotechnical advice.

Jan 1, 1993

The financing of mineral ventures is usually supported by the valuation of a mineral asset, the physical size and composition of which have been determined within quantified limits of accuracy in order that the lending or investment risk can be assessed. The Resource or Ore Reserve estimation is the measurement of that asset and may be the outcome of complicated processes of interpretation and estimation requiring an extensive knowledge and understanding of the general nature of ore occurrences, and of the particular deposit under review. In arriving at an interpretation of the nature and physical distribution of minerals in a deposit, observations may only be available from widely spaced samples and geological knowledge and principles are of prime importance. Consultants may be asked by the lending or investing body to "provide comfort" on the quality of the Resource or Reserve estimations and providing such comfort casts substantial obligations of diligence on the consultant.

Jan 1, 1990