Search Documents

By Davey KJ

Complex sulphide ores are characterised by complex texture of the valuable minerals. Any assessment of the performance of differential flotation circuits treating such ore should include analysis of the effects of poor liberation of the valuable minerals. Selected samples were taken from balanced size by size surveys of the flotation section of a concentrator treating an ore body containing fine grained galena and sphalerite in a matrix of iron sulphides which is mostly pyrite. liberation measurements were made using the QEM*SEM system on four or seven size fractions. The measurements indicated that less than 40 per cent of the galena and less than 60 per cent of the sphalerite in the flotation feed was liberated. The final concentrates were largely composed of composites of valuable minerals and iron sulphide however there was a small but significant fraction of liberated iron sulphide. Using the sized mineral flows obtained from the original balances and the liberation measurements, a satisfactory liberation balance was obtained. This enabled the effect of liberation on the flotation performance to be examined; not only for the entire circuit but also in the rougher, scavenger and cleaning sections. In the zinc circuit the effect of a regrind mill could be assessed. Recovery of galena in the lead circuit was limited by the recovery of composite lead particles. Recovery of liberated galena exceeded 95 per cent in all size fractions while the recovery of composite galena exceeded 85 per cent below 38 ¦m but fell sharply above 38 ¦m. Examination of the behaviour of the liberated and composite galena in the various sections of the lead flotation circuit revealed high recoveries of both liberated and composite galena particles in the roughing and scavenging sections but very low recoveries in the final two cleaning stages. Similar trends to those observed in the lead circuit applied in the zinc circuit although the performance of the liberated sphalerite also fell off at sizes greater than 38 pm in this case. Thus the zinc recovery was limited by the flotation of both the liberated and the composite sphalerite. The effect of regrinding was to increase the recovery of sphalerite mainly by reducing the amounts of sphalerite in less liberated sizes rather than by increasing the liberation of the sphalerite within a given size Fraction.

Jan 1, 1993

The value derived by good mine planning is often underestimated as many mines steer their attention to the more immediate and more easily recognised successes made by the day-to-day operational æbush fireÆ fighting. Similar to machine maintenance, the efforts made to quickly rectify short-term breakdowns are well recognised; whereas the value derived from the work in planning, scheduling and undertaking preventative maintenance is not so obvious or readily quantified. Too often the focus of the business shifts to building and supporting an efficient operations team at the expense of developing a highly experienced team of mine planning practitioners that are well trained with procedures and purpose-built tools to develop optimum mining strategies. A resource has an inherent value based on its quality parameters and its likely mining conditions. How well that value can be unlocked is governed, to a large degree, by the proficiency of the mine planning practitioners, as they, essentially, set the foundation of the mine business and the path along which the mine will operate. The importance of having a well documented and procedural mine planning methodology that integrates both a thorough technical and economic understanding of the resource cannot be over emphasised. The aim of the mine planning process is to develop a robust mine design and production capability which can best cater for future uncertainty whilst providing the best opportunity to maximise cash flow into the business. The planning process must be transparent and auditable, clearly summarising the process steps and assumptions made to arrive at a justifiable and defendable outcome. To provide maximum value to the business, the planning process must be repeatable and scalable to enable easy replication throughout the different mines and projects within an organisation. The diminishing numbers of highly experienced personnel within our industry, coupled with the growing pressure to clearly demonstrate that appropriate due diligence has been exercised, means that well documented and monitored mine planning processes using purposed built and innovative tools need to be developed to ensure optimum outcomes.

Jan 1, 2009

All minerals contain radioactive elements, from the uranium ores of the Gabon, which contained sufficient uranium to initiate a natural nuclear reactor, to the very low levels of some recent evaporites. The commonly occurring heavy minerals such as ilmenite, rutile and zircon are no exception to this and contain varying qualities of radionuclides, depending on the source. With recent changes in legislation many natural minerals may become officially classed as radioactive. Such moves can inhibit the sales and exploration of many minerals in the heavy minerals suite. The many negative perceptions associated with the word radioactivity can produce an over cautious reaction from regulators and users. This paper presents a method of managing the radioactivity issues associated with minerals such that the safety aspects of workers and public are not compromised, whilst allowing the commercial use of such minerals to continue in a sensible manner. The paper focuses mainly on the mineral zircon and its uses. However the legislation changes particularly in Europe and the USA have the potential to affect all minerals imported into or produced in those countries. The model developed for addressing the issues of zircon radioactivity may be readily applied to other minerals since legislation governing such matters is not mineral specific. There is a strong need for education of both regulators and users of minerals. Regulators are usually not aware of the specific properties or uses of individual minerals. Similarly mineral users are not aware of the radioactive nature of their materials or how to manage this property. The paper concludes by recommending strong cooperative action by both producers and users of minerals to protect the future of their industry.

Jan 1, 2001

Technical control in an industrY invariably leads to a basic contribution from the science of chemistry. It is interesting to note. that the change from the "Assay Office" to the "Chemical Laboratory" has already taken place on the majority of progressive mining fields.Although the serlvices of an efficient chemical staff are freely availed of by operating departments, it is not generally realized that practical chemistry is definitely expensive. A great deal of misplaced energy and expense can be involved in an enthusiastic research campaign where a full appreciation of laboratory economics and a balanced sense of analytical values are lacking.In order to supply data to the various departments concerning individual costs, it was decided at the North mine to issue a supplementary sheet concerning laboratory activities.The costs are compiled under the Unit System, which is based on a relative comparison between the total cost of the various determinations. carried out and the number of such determinatiQns converted to an equivalent aggregate of units.The introduction of the system necessitates the initial compiling of a table of relative units for the various estimations carried out on the works. Each laboratory will find it necessary to draw up such a table governed by local conditions, and, as will be anticipated, a relative comparison of the cost for any particular estimation will show a variation on a lead field, a copper field, or a steelworks, etc.This is due, of course, to the predominating type of routine work, cost of landing reagents, frequency of assays, etc. The satisfactory preparation of the Unit Table requires a good knowledge of laboratory procedure.

Jan 1, 1940

By J S. Moema, R Paton, J Zimba

Today, most organisations are familiar with the pressure to increase their effectiveness and efficiency, regardless of the nature of their business. Cost cutting and increased productivity are the main themes of many initiatives to ensure the profitability of operations and, ultimately, shareholder satisfaction. It is well known that the cost of comminution to liberate minerals such as gold from their respective ores is a major expense for mines. Comminution costs consist predominantly of grinding balls and electricity. However, there are no national or international standard specifications for grinding balls û on which a single mine may spend several million dollars per month. In addition, in the past mines generally did not specify the minimum requirements when purchasing grinding balls from suppliers. The result is that every supplier has its own grinding ball recipe (regarding chemistry and heat treatment), and is under no pressure to implement a quality assurance plan to ensure that a consistent product is delivered. The resulting variation in the quality of grinding balls leads to increased steel consumption rates and hence increased milling costs. A more stringent quality plan will generally not be welcomed by suppliers since this may entail further investments and/or reduce the production rate. In a sense, suppliers benefit from poor quality grinding balls as this leads to increased sales. Perhaps the main problem is a lack of understanding of the factors that influence grinding ball performance. This paper will describe the factors that influence the wear rate of grinding balls from both a microstructural perspective and a mill perspective. In addition, some insights are provided on the different grinding balls available and ways that users can verify their quality.

Jan 1, 2007

A number of mines in Australia have experienced premature detonations caused by bulk explosives reacting with the rock type being blasted. Premature detonations are extremely high risk events as they are unplanned, occurring at any place, at any time, potentially resulting in high loss (personnel and equipment). Many Australian mines have also experienced spontaneous combustion where spilt explosive reacts vigorously with the rock type. Premature detonation in these cases does not occur due to the lack of confinement and the volume of explosive present, but these reactions could impinge on the surface initiation system and provide an early warning of future premature detonations. The explosive ground reactivity phenomena is not restricted to Australia with similar incidents being reported in North and South America, South Africa, China and South East Asia. All reported incidents have two common denominators, being the presence of sulphide rock types and nitrate based explosives. Both premature detonation and spontaneous combustion result from the same series of reactions of partially weathered sulphides that ultimately result in the violent decomposition of the ammonium nitrate based explosive. A number of relatively easily observable indicators can be used to assess a particular minesiteÆs potential for explosive ground reactivity. The presence of two or more of these indicators means that minesite personnel should contact their explosives manufacturer for assistance in determining if a problem exists and if so then developing strategies to overcome the situation. The paper describes the indicators as well as discussing, via a case study, the holistic approach required to efficiently develop a relevant æSafe and Efficient Blasting ProcedureÆ to deal with explosive ground reactivity problems.

Jan 1, 1999

An Investigation on the Effect of Chrysotile Particle Shape and Anisotropic Properites on the Rheology of Chrysotile Suspensions Chrysotile, a polymorph of serpentine, is a phyllosilicate mineral that occurs as a major gangue mineral in many ores (eg Mt Keith nickel sulfide ore, Western Australia). The rheological behaviour of chrysotile stems from two main factors: its distinctive morphology and its electrical surface charge. It is believed that these factors are central to the problematic rheological behaviour and low solids throughput typically experienced in the processing of such ores. In this work, a study of the effects of chrysotile surface charge properties and particle shape on the rheology of chrysotile suspensions was conducted. It was found that the rheology of suspensions of pure chrysotile is characterised by extremely high yield stress values over a broad pH range (pH 4 to 11).The disparity in the point of zero charge and range of maximum yield stress for chrysotile is consistent with the anisotropic nature of chrysotile particles. A comparison of the rheological behaviour of quartz suspensions (non-fibrous) to that of chrysotile suspensions (fibrous) provides a practical indication of the effects of the fibrous nature of chrysotile relative to non-fibrous minerals. The long, thin fibres are easily entangled to form suspensions with much higher plastic viscosities and Bingham yield stresses than non-fibrous particles. Chrysotile particle shape and surface charge are central to the rheology of chrysotile suspensions, although shape appears to play a more significant role in this regard. This fundamental study would be beneficial to the ongoing research for improved recovery in the Mt Keith nickel sulfide ore as well as other chrysotile bearing ores.

Sep 13, 2010

By Kavetsy A

In surface mining operations, the ease with which a muckpile may be dug is a dominant factor in mining efficiency. Within broad limits this is largely independent of the fragment size dis- tribution, since the equipment used to move the broken rock is generally larger than in underground mines. In such cases, muck- pile shape and voids ratio within a muckpile heavily influence mine productivity. In a particular operation, the muckpile shape after blasting should be tailored to the digging equipment being used. A front- end loader is best suited to a low, flat-lying, loose muckpile, because of its fairly good mobility and small break-out force with its bucket. In contrast, a rope shovel lacks mobility, generates a much larger break-out force with its bucket, and fills its bucket in a vertical filling motion. Therefore, it is ideally suited to well fragmented, steep faces. In situations where a dragline is used, the requirement for a suitable muckpile depends on the operat- ing scheme of the dragline. For a conventional highwall key method the preferred work- ing level of the dragline is the same as the highwall, so that the dragline may sit over its key. In this situation, the ideal muck- pile shape involves relatively little displacement of the fragmented rock, with a minimal "power trough" at the back of the blast. In throw blasting, on the other hand, it is desirable to cast as much of the spoil as possible across the pit. It is then necessary to optimize the blast design by maximizing the throw percentage under any necessary constraints (e.g. damage, vibration, flyrock, explosive cost).

Jan 1, 1988

By Edmonds G. A

The power station went into operation in 1931, when the installed capacity was 12,500 kVA. with a loading of 4,000 kVA. In 1936 the loading increased to 6,750 kVA. which necessitated the addition of a third set which went into operation in 1937, the installed capacity at that date being 18,750 kvA. with a loading of 7,000 kVA. This remained fairly constant until 1945, when a gradual increase was noticed, the loading in 1952 being 10,598 kVA.With the addition of the copper plant, additional generating capacity was required and it was decided to raise the installed capacity by the addition of a fourth set to 34,375 kVA. with an expected loading, when producing copper, of 20,000 kViA.MAIN POWER PLANTThis consists of three GiE.e. alternators of 6,250 kVA. or 5,000 kW. at 0.8 P.F. rating and one G.E.C. alternator of 15,625 kVA. or 12,500 kW. at 0.8 P.F. rating, making a total generating capacity of 34,375 kVA.Each alternator is driven by Fraser and Chalmers turbines at 3,000 r.p.m.SYSTEMThe main 3 phase 3 wire 3,300 volt distribution system has the neutral point of alternators earthed through by one or two earthing resistors designed to limit earth fault current to 3,000 amp. for 20 seconds, in the case of the large machine, and to 1,100 amp. for 10 seconds, in the case of the smaller machines, or full load of either size machine at rated voltage.

Jan 1, 1953

The history of civilisation continues to register a steady tide towards the urban life as the basis of its social organisation. The manifestation of this movement is a continuous growth and increasing density of population in our towns and cities, as the favourite space for the development of humanity. Naturally, this trend raises a certain number of problems which grow proportionally with the size of the city. The use of the underground space has an important role to play in solving such urban problems. But various issues must be taken into account when developing urban underground space.

Jan 1, 1999

Operation of the tankhouse at the Electro lytic Refining and Smelting Company's works has been improved, but further automation is re- quired to cut the labour intensive nature of the routine tasks. Anode quality, both chemical and physical, plays an important role in efficient refinery practice, and impurities such as lead, antimony and nickel have required careful monitoring for smooth operation. The gradual replacement of copper blanks by titanium has markedly improved the quality of starting sheets, but problems have been ex- perienced with surface preconditioning of the titanium blanks. Polishing with emery paper proved to be a successful technique.

Jan 1, 1976

The mining industry in common with the rest of Australian industry is in the critical situation of facing a rapidly diminishing insurance market. Huge industrial complexes and massive mining risks with limits of liability of millions upon millions of dollars are becoming increasingly difficult to insure. Insurance underwriters are still reeling from the financial shocks of cyclones, floods and fires in Australia over the past couple of years. Risk Management which calls for manage- ment involvement in the control of losses offers a serious challenge to miners, industrialists and insurance underwriters alike. Without it the insurance market could disappear altogether.

Jan 1, 1975

In planning its production and investment activities the mining industry has generally paid too little attention to perceptive analysis of its market environment. The nature of world economic difficulties over the past decade is not a mystery. Essent- ially prolonged affluence has engendered a false sense of security and fostered entrenched vest- ed interests hostile to economic change. The overall outlook remains poor. For mining projects mineral demand affects both product prices and the availability of specific sales outlets. Long-term projection of demand is complex and a key to success is concentrating on analysis of fundamental deter- minants and avoiding mindless extrapolation.

Jan 1, 1983

By Xin J

In China, the State-run mines are currently practising an information card management system, to collect data about mine production and safety condition. Since large volumes of data will be obtained every day, efficiently and effectively processing data and sorting out valuable information will take enormous resources of manpower, if by hand. Therefore, an intelligent database system with easy data inputting was developed to assist information processors in data classifying, filing and retrieving. For analyzing and improving production performances, reliability models and production functions were embodied. The system was implemented on AST-286 in DBASE M. Preliminary applications have proved effective and successful.

Jan 1, 1991

The Income Tax Assessment Act ["the Act"] levies tax on a taxpayer's taxable income. At a time when commerce and life were more simple, the calculation of taxable income had some connection with logic and a taxpayer's capacity to pay. However, as a result of successive governments' different views of equity, their perception of avoidance, their needs for revenue and their changing views on capacity to pay, the rules determining the calculation of taxable income have continually changed to the point that logic is no longer relevant. Taxable income now is simply the product of the application of a complex set of rules.

Jan 1, 1990

By Hryniewicz M

The paper presents a sound critical estimate of mathematical models presently used for the process of compaction of fine-grained materials. It shows the mathematical model of compaction developed by the authors, which was used to formulate the program of computer simulation of the process. The examples of computer simulation experiments of compaction of selected fine-grained materials regard the results of the experiments made by the authors on variability of external friction occuring in this process. Simulation examination presented in the paper crucially contributed towards the original method of selection of rational compaction technologies of fine-grained materials developed by the authors.

Jan 1, 1993

Organic dyes such as nigrosine and sun yellow act as depressants for carbonaceous particles in the, flotation of sulphide ores. Depression is achieved when initially hydrophobic organic surfaces are made hydrophilic by preferential adsorption of dye molecules. Experimental studies, mainly on Mount Isa ores, indicate that dyes are adsorbed as planar anionic micelles attached to carbonaceous surfaces by van der Waals and ion exchange attractive interactions. Relationships appear to exist between the amount of organic matter on the surface of ground particles, the surface area of the particles, the "saturation" adsorptions of dyes, and the degree of difficulty experienced during froth flotation.

Jan 1, 1975

By Henderson J, Ward RG

Dissolved oxygen has been measured directly using a rugged, reliable, accurate electrochemical probe system developed for steelworks application by B.H.P. Central Research Laboratories. Furnace measurements show that the steel is generally supersaturated with oxygen and that oxygen contents vary considerably from heat. to heat. Ladle measurements also show considerable heat-to-heat variations. Analysis in terms of ladle deoxidation chemistry differentiates between carbon monoxide controlled and manganese silicate controlled oxygen levels. Deviations from these levels are sometimes due to aluminium present in other added ladle alloys but in some cases the plant applicability of laboratory derived equilibria is questionable.

Jan 1, 1972

Changes in prices and costs change the mineable grade and the profitabil- ity of an ore reserve. In a static world the grade required for an ore reserve is measured by the ratio: Cost/tonne of ore x 100 Price received/tonne of product and profitability by the ratio:- Price received/tonne of product Cost/tonne of product If the words cost and price refer to average cost and average price over some suitable period, say 3 to 5 years, the above ratios express the convent- ional wisdom of the mining engineer, and assume there will be no change in technology or politics.

Jan 1, 1979

Robe River Mining manages a large open pit iron ore mine in the Pilbara region of the North-West of Australia. The mine is managed for various joint venture participants.In July 1986, Robe River Mining made various changes to its management philosophy, which were heavily publicised in the media at the time.As a result of those changes to its management philosophy, Robe River Mining has been able to dramatically increase its production output, productivity, and safety performance without having to resort to major capital outlays and without the benefit of restructuring of applicable industrial awards.

Jan 1, 1992