Search Documents

By Just G. D

The results of a geostatistical analysis of geochemical data obtained from field measurements are described in the paper. Q values derived from seismic signal rise times for different travel paths in the rock masses were used in the study. Cross-hole seismic measurements made at surface and underground sites formed the basis for the work. Geostatistical estimation of average l/Q values for area of the rock were compared with geological interpretions of rock type distributions. Reasonable correlations were obtained between the two methods of rock quality estimation.

Jan 1, 1988

Over the last few years several important developments have taken place in the Electro- lyte Purification Plant at Copper Refineries Pty. Ltd. A fully automated system for the continuous removal of arsenic has been develop- ed. A submerged combustion process for the removal of nickel has been developed to a stage where patent coverage has been obtained in most of the copper producing countries. A plant has recently been commissioned for the production of Tetra Cupric Arsenate, which it is hoped will find a ready market in the timber preservation industry.

Jan 1, 1974

By Bangerter PJ

The use of gravity concentration is, and has always been, the conventional primary method for gold recovery from alluvial deposits. The development of high capacity cone concentrators and metallurgically efficient wash-waterless spiral separators has had some impact in the technology for alluvial gold processing, but perhaps more significantly has led to the relatively recent use of this gravity concentration technology in grinding circuits of hard rock ore for "coarse" gold removal and for scavenging gold locked in sulphides from cyanidation tailings streams.Gravity concentration systems are relatively low-cost, non-polluting and energy efficient; and their judicial use in gold treatment plants can significantly reduce overall capital and operating costs.The application of modern gravity concentration technology to hard-rock and alluvial gold ore treatment is discussed. Flowsheets and test and operating data from a number of gold processing operations incorporating gravity concentration treatment are presented.

Jan 1, 1984

The first stage in process design for coal preparation is a study of the coal seam and its associated features followed by an examination of the mining method to.be employed and the coal market requirements. Normally benefication is based upon the differences in relative densities of the coal constituents and asso- ciated ash forming components. Since initial liberation is obtained at a relatively large particle size, the size to which coal is crushed is more subject to the market requirements than to liberation studies. It is possible to estimate energy requirements for comminution and recoveries and product grades can be cal- culated following the interpretation of standard laboratory tests. Numerous units are available for the separation and concentration of the components of run of mine coal in- cluding jigging, dense media separators, and for the finer particle size fractions, flowing film separators, dense media cyclones and froth flotation.

Jan 1, 1975

By Denholm WT

Current control practice is reviewed for agglomeration processes, including pelletising, sintering and induration; and for smelting processes, including blast and reverberatory furnaces, flash smelting, the intensive bath smelting processes together with converting. The importance of sensors for on-line control and the status of mathematical modelling is discussed.Future progress in automatic control will require improved component specific sensors and the use of validated mathematical models running in parallel with the process. The possibilities in both these areas are reviewed in light of the trends towards more intensive smelting processes.

Jan 1, 1985

By Pinn N

Geosynthetics is an all encompassing word to describe a number of man-made products usually from hydrocarbons which are used in conjunction with the soil. The specific products are:Geotextiles Geomembranes GeonetsGeogrids GeocompositesIn mine establishment and associated construction work, Geosynthetics have proven to be successful in a wide range of applications. For example, geotextiles are now used to assist with the establishment of access roads, site preparation, haul roads and in connection with the construction of embankments for storage ponds and dams as well as for general hydraulic and foundation engineering problems.

Jan 1, 1990

By Kerr I. D, Kennedy M

Flash X-radiographs were obtained of commercial electric No 6 and No 8* strength aluminium tube detonators in small-diameter cartridges of emulsion explosive at various times after fusehead operation. The trigger system for the radiography was based on the detection of light following fusehead firing via optical fibres inserted into the fusehead cavity during detonator assembly. These experiments were simulated using a finite element hydrocode with realistic treatment of the non-ideal reaction kinetics. Excellent agreement was demonstrated for the shape and position of the shock waves. In both cases, initiation of the emulsion was predominantly forward from the detonator. For the No 8* strength detonator, this initiation resulted from the shockwave delivered through the sides of the detonator, while for the No 6 strength detonator, initiation was the result of a complex interaction between shockwaves originating both from the sides and from the endcap. In the reverse direction (towards the crimped end of the detonators), initiation was only weakly dependent on detonator strength, being controlled mainly by the competing processes of rarefaction from the cartridge boundaries and comer turning of the detonation wave from the forward initiation. The consequences for field performance of small-diameter emulsions will be discussed.

Jan 1, 1990

EQUIPMENT TO BE DISCUSSED It is the intention of this paper to discuss the transporting of large skid mounted equipment and track machines around open cut mines. By large I mean 100 to 350 tonne capacity being trans- ported on minesite lowloaders and the capability of moving loads of 300 to 1200 tonne by other means. It is also possible to move larger loads. The main factor in transporting large loads is eco- nomics and is a balance between the cost of the transporter and the increased production from the equipment being moved. For example it could be possible to shift a 7000 tonne dragline faster than their own means of propulsion, being the "walking feet" method. However for the cost of $10 to $12,000,000.00 or more you can afford to walk the dragline and suffer the production loss. Let us concentrate on the economically realistic. BOSICH FBT MINESITE LOWLOADERS 100 TO 350 TONNE CAPACITY. Why initially consider having such a transporter? Our experience has shown that initial enquiries evolve from mines requiring to move large drills, 50 to 200 tonne weight and large hydraulic excavators or backhoes which are track mounted. The reason for shifting them is to move equipment from a mining face to enable blasting, to remove to the central workshop for repairs, overhauls and routine maintenance, to transport equip- ment from one mine face to another, and for drills, to move from one drilling pattern to the next. The cost in terms of time lost and extra wear on tracked equip- ment easily justifies the cost of the transporter. The tracks on large drills and shovels are not intended for long distance walk- ing. These tracks are designed to move the machines to position for drill holes, or moving around the mine face. Long distance travel, ie generally 1 km or more, results in overheating of track rollers, track drive components and accelerated wear on tracks.

Jan 1, 1989

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

By D Landriault, G W. Wilson, L Langetine and

Engineered soil covers are used for final closure options for both waste rock and tailings disposal facilities. Currently, cover construction requires excavation of appropriate cover material from a nearby site. If no suitable materials are available, the mine operation may have to ship appropriate materials long distances to the site before the construction of the cover can even begin. This has led to the proposal to engineer cover materials using existing waste materials from the mining operation. The paper presented here describes the results of a laboratory scale testing program to evaluate the potential for blending waste rock, smelter slag and tailings for the creation of a suitable cover material at a site in Canada. Tailings from the local mill, waste rock and slag were collected in the field and blended to create a material with an air entry value similar to the tailings and with physical strength similar to the waste rock. Testing indicated this mixed material could be blended at a consistency of a paste and was suitable for pumping. It can also be compacted to a high-density material. The preliminary results show that it may be possible to blend waste rock, slag and tailings into a material that can be utilised in the construction of a water retaining cover.

Jan 1, 2003

By D A. Aitzhanova, E Zh Omirzakova

The Republic of Kazakhstan has well developed mining and metallurgical complex. In modern conditions, when deposits of useful minerals are running thin, it is very important to find additional sources for obtaining necessary products. As our investigations showed different kinds of waste may be used for producing of different kinds of products, which are successfully applied in different branches of KazakhstanÆs economy. Analysis of ways for increasing of complex use of mineral raw materials of different deposits, widening raw mineral materials base and decreasing negative effects on the environment, are presented in this paper.

Jan 1, 2003

By Jin C, Shu H

The effect of operating parameters of a shaking table on the separation of mixed quartz-magnetite artificial feed has been experimentally investigated by use of laboratory-scale shaking table. Based on a great number of experimental data collected, the multi-variate non-linear model of shaking table has been developed. The model allows for the calculation of the product grade and recovery. A computer model has been programmed, for inclusion in a software package for the simulation and optimisation of shaking table if the feed characteristics and the concentrate grade are given.

Jan 1, 1993

By D Yuen, J A. D Connolly, T V. Gerya

Recent works suggest that dehydration of subducting slab and consequent hydration and partial melting influences the dynamics of mantle wedge. Plums originating form the subducting slab due to Rayleigh-Taylor instability are responsible for heterogeneous composition of the mantle wedge. Also, occurrence of partial melt in the mantle wedge can trigger dynamic processes like exhumation of UHP rocks in intra-oceanic settings or can influence characteristics of the subduction tectonic regime. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Sun Yubo

A basic method for designing reasonable jig cycles for movable-screen jigs is presented in this paper. The reliability and effectiveness of the designed jig cycle was verified with tests performed on an artificial mixed material. An iron ore (12 - 100 mm) from Huashugo Iron Mine, Jiuquan Iron and Steel Company, was treated in the TJD-75 movable-screen jig using the designed jig cycle. A good result was achieved. The procedure presented here should provide a reliable technique for the design of a commercial movable-screen jig.

Jan 1, 1993

By W Whiten

The determination of mineral composition is necessary in the mineral sands industry. Tiwest has developed a procedure for safe and convenient determination of the mineral composition using a magnetic separation followed by chemical analysis using X-ray fluorescence spectroscopy. This then requires the conversion of the elemental assays to mineral compositions. A project at the Julius Kruttschnitt Mineral Research Centre has developed a convenient analysis method for this conversion. This analysis is based on a reconciliation of the of the assays of the sample with the standard mineral assays by making minimal adjustments based on the assay accuracies to both sets of assays. As well as providing the mineral composition it to be tested for other applications and variations of the procedure to be evaluated. Given a range of samples, testing for the accuracy of the assays of the standard minerals, has been demonstrated.

Jan 1, 2001

Explosives have been an important tool for unlocking minearl wealth from the earth's crust for several countries. In'the past, innovation in explosives technology, spurred on by industry needs has assisted the Mining Industry to improve productivity and reduce costs. A symbolic relationship exists between Explosives and Mining. Australia has vast mineral wealth. Our Mining Industry is of major importance to the Economy., The value of mineral produc- tion in 1987 was $25 million or 10% of GDP. Australian Mining is a business depending on international markets. The Mining Industry is our leading export earner, generating 44% of all export income. 60% of mineral production is exported. About half of these minerals are extracted using explosives. Explosives rank as one of the top three consumable expenditures for a mine. For example: A major open-cut iron or coal mine can spend $6 million dollar per annum on explosives.

Jan 1, 1988

By Scholl EW, Ricken W

The simultaneous presence of fuel, oxygen, and of an ignition source is necessary for an explosion to arise. If one of these conditions is missing an explosion cannot take place. A continuous reduction of oxygen, often applied as a protective measure in surface plants, is not to be considered for underground mining because of possible danger to persons. Therefore, measures for avoiding explosions can only be concerned with lowering methane and coal-dust concentrations to an undangerous level and avoiding ignition sources. As these measures alone are not sufficient, additional ones have to be taken to keep the effect of an explosion as low as possible. Measures for controlling and monitoring methane are essential. Although the formation of dangerous coal dust concentration cannot be avoided it can be reduced. Dust-binding by means of hygroscopic pastes and dusting with limestone dust are effective measures to pre vent explosions.

Jan 1, 1981

North Flinders Mines Limited (N.F.M.) is an Australian-owned mineral exploration and mining company based in South Australia. In the 1970's it researched the prospectiveness of the Tanami (central western region of the N.T.) for the identification of possible economic gold deposits. Having outlined the potential for such a deposit at The Granites (550 km. N.W. of Alice Springs), it marked out and in 1975 applied for the grant of eleven gold mining leases (G.M.L.'s) under the provisions of the then Mining Ordinance. This application was deferred by the Commonwealth Government during the time of the Aboriginal Land Rights Commission (Woodward), subsequent enactment of legislation and land claims. In 1980, the Walpiri and Kartangarurra-Kurintji land claim encompassing the G.M.L.'s, became Aboriginal land. It therefore became necessary for N.F.M. to negotiate a mining agreement with the Central Land Council (C.L.C.) represent- ing the Traditional Owners, before the G.M.L.'s could be granted. In August 1983, the C.L.C. and N.F.M. concluded an agreement to enable the grant of mining interests necessary for the devel- opment of The Granites Gold Project. In several ways this agreement is unique in That:

Jan 1, 1984