Search Documents

By D David

Geometallurgy is often a misunderstood and poorly defined concept. The first thing the paper will attempt is to provide a definition of geometallurgy. Ultimately this paper has been written to provide guidance to geologists, mining engineers and processing professionals as to what geometallurgy means in the crucial early phases of a potential mining project between the time of discovery and the time of commencing construction, should this occur. The paper covers the options available for conducting a geometallurgical study of a resource or orebody, appropriate to the level of definition required in the projectÆs development cycle. The paper will then describe how the geometallurgical information generated is subsequently used in calculations, planning and preparation of reports designed to inform and reassure stakeholders, such as the market. Ultimately in a successful project, appropriate options adopted in the development phase will form the basis of an ongoing geometallurgical program that links the major site disciplines for the good of the operation.CITATION:David, D, 2013. Geometallurgical guidelines for miners, geologists and process engineers - discovery to design, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 129-132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Kentwell

This extended abstract and associated presentation provide a series of real examples of the complex interactions between the numerous input parameters, both geological and mathematical, that are required for resource estimation. Many of these parameters can contain a large degree of uncertainty at the initial resource stage. The resource tonnages and grades at economic cut offs of some types of deposits are relatively robust to these initial uncertainties while others exhibit significant sensitivity. In some cases, changes in parameters can result in counter-intuitive outcomes. Grades and confidence levels are inseparable; as the parameters change the confidence changes and so does the grade estimate. The extended abstract and associated presentation also discuss the question of whether or not a single solution is still an acceptable outcome for an estimate or if even a set of simulations based on a single fixed set of parameters is acceptable.CITATION: Kentwell, D, 2018. Sensitive dependence on initial conditions in resource estimation, in Proceedings Complex Orebodies Conference 2018, pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

This paper examines the complex interplay of deposit characteristics, mining plans, tailings disposal techniques and rehabilitation requirements on planning for mineral sands operations. All component parts of this mining cycle are interdependent and cannot be evaluated in isolation when optimising a mineral sands operation. This is most evident when projects are large-scale or involve resources that contain complexities such as high slimes content, consolidated hard band materials, acid forming materials and radioactive materials. Projects located in environmentally sensitive areas add further to the need for more stringent planning. This paper describes the analysis techniques adopted by Hatch to evaluate mining and tailings placement options for a dredging and floating concentrator system. The principles and methods used in the analysis are applicable to any mining system involving the complexities listed above. The focus of this paper is on the reconstitution of mined material as tailings and the impact of this process on mining schedules and tailings construction and placement options.

Jan 1, 2001

PIP is regularly engaged in businesses where Greenfield Capital Projects are under- delivering on the expected business case. In most of these projects, we can identify that rigorous review has been carried out on the design and financial cost elements and substantial reporting is maintained to Boards on progress versus plan of project completion and cost. However, in all sites of this nature that we have worked at, the planning, design and execution of the operational elements or æwiringÆ of the organisation have fallen short and resulted in significant extra cost or opportunity cost (lost tonnage or quality) during start-up. When compared to the amount of planning and resources that have been poured into the capital side, the ledger on the æwiringÆ side is typically fairly sparse. This presentation outlines the importance of running a disciplined, rigorous process to prepare the human and wiring side of a start-up to ensure rapid start-ups and put the site on the pathway to high performance. It gives an outline of the rigorous process PIP has used with projects to ensure excellent start-ups.

Jan 1, 2006

By R Berthelsen

The Peak Gold Mines Pty Ltd (PGM) operations are located approximately 9 km south of Cobar, NSW. PGM currently mines and treats ore from three separate orebodies within 5 km of the original plant. Production from the original Peak orebody ceased in April 2002, with ore currently sourced from underground at New Occidental and Perseverance, while New Cobar supplies ore from an open cut mine. In March 2003, Wheaton Minerals Asia Pacific purchased the operation from Rio Tinto who operated the mine for around ten years. The Perseverance deposit is situated between 600 and 1000 m south of the Peak orebody. Access is via shaft from Peak to 630 m below surface and then by decline to the northern end of the deposit locally known as Zone A. Development of the resource commenced mid 2002 to set up for a long hole open stoping operation at 25 m level spacing. The first production stope was successfully brought on line December 2003. The Perseverance deposit is hosted by sediments and volcanics along the eastern margin of the Devonian Cobar basin and is one of many deposits with the Cobar Gold Field. The Cobar Gold Field has produced approximately 2.5 million ounces of gold since 1880. The Perseverance area had long been considered prospective due to the presence of old workings at the southern extensions of Peak line of lode. Significant mineralisation was first discovered at Perseverance in 1994 when PGM drilled a hole targeted 950 m below the historic workings. The target was based on an apparent plunge to the stratigraphic controls to the Peak Orebody. Subsequent exploration within and around the ægreaterÆ Perseverance area has been significantly aided through the use of downhole electro-magnetic surveys due to the close spatial association between gold and sulfide mineralisation.

Jan 1, 2004

By C Wu, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Halasu porphyry copper belt, located in the East Junggar basin bounded by Chinese Altay to the north and the Tianshan mountains to the south in the Central Asian Orogenic Belt, is one of the major porphyry copper belts in Xinjiang province, north-west China. Combined with previous studies in this area, the magmatism can be divided into three periods: pre-mineralisation activity of 390 Ma syn-mineralisation activity of 380–370 Ma post-mineralisation activity of 360–330 Ma.Through the comparison of zircon chemistry from ore-bearing and barren syn-mineralisation intrusions, negative correlation was identified between Ti-in-zircon temperatures and oxygen fugacity, corresponding to the fact that late-stage syn-mineralisation granitoids contain high water content, high oxygen fugacity and low temperatures with higher mineralisation potential. In addition, the relative low initial 87Sr/86Sr ratios, high eHf(t) and eNd(t) values and mantle Pb isotope characteristics in this study support that the magma forming these intrusions was probably derived from juvenile crust generated during subduction-accretionary processes.CITATION:Wu, C and Chen, H, 2015. Zircon trace elements and Sr-Nd-Pb-Hf isotope systematic of the Halasu porphyry Cu belt, north-east Xinjiang, China, in Proceedings PACRIM 2015 Congress, pp 637–640 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Batch centrifugal gravity concentrators have become standard equipment in gold grinding circuits for recovery of gravity recoverable gold (GRG). The downstream benefits of installing a gravity circuit are well understood, and in general, if there is a reasonable amount of GRG in the ore, a gravity circuit is usually installed. The benefits of gold gravity recovery have also been well documented, with a large database of successful case studies. As well, predicting production scale gravity recovery results ahead of installing gravity has become a common practice. The missing link between lab and full scale has always been the ability to predict the recovery benefit of installing gravity ahead of actually doing so. Being able to predict the recovery benefit in advance would help an operation in assessing the economic benefit and help justify the capital costs of the gravity circuit with much less uncertainty.

Aug 1, 2010

By B Murphy

Seeking to reduce the likelihood of uncontrolled personnel entry into the operating footprint of a dragline, Coronado Global Resources initiated a review of proximity detection systems currently available and equipment interactions in and around dragline operational areas. At the time of the assessment, there were no established personnel proximity detection systems in compliance with functional safety standards for large machinery in Australia. Our primary objective was to guarantee a functionally safe outcome, particularly by implementing a performance-level-rated system in accordance with AS4024 (Safety of Machinery series of Australian Standards). Applying appropriate detection technologies, the goal was to reduce the residual operating risk for machine-to-machine and machine-to-personnel interactions. A comprehensive analysis of available or in-development technologies was conducted, and a layered approach (demonstrated in Figure 1) was adopted to achieve the desired risk reduction by segregating the sensing zones into distinct areas using diverse and disparate technologies consisting of radar (short); light detection and ranging (LiDAR) (medium); and optical (long). To address the potential limitations of each technology, overlapping layered sensing zones were designed. With LIDAR and optical using two distinct artificial intelligence (AI) systems to classify detections, these were specifically trained to handle the unique environments of a mining operation.

Sep 1, 2024

Distillation of the large and growing greenhouse literature indicates that: ò Global warming has occurred over the past century or more; ò Build-up of CO2 (and lesser greenhouse gases) in the atmosphere is a fact; ò This build-up is likely to cause further global warming. It does not appear possible to conclude that the observed C02 build up and observed global warming are linked; nor is it yet possible to forecast global or regional climate variation with conviction. The dominant greenhouse gas is C02 with about half the warming potential of those gases emitted by man's activities; and about 80% of anthropogenic C02 emissions are from the burning of fossil fuels. Fossil-fuel C02 emissions arg divided about equally between the developed countries of OECD and the rest of the world. However C02 output growth over the past decade was about 4% for OECD and some 40% elsewhere. Population growth and pressure for better living standards will ensure continued higher growth outside OECD. Uncertainty about the impact of increasing C02 emissions on climate, and the long lead-times involved in limiting the increase in atmospheric C02 concentrations, are good reasons for taking action now. Australia accounts for about 275 million tonnes a year or just over 1% of the CO2 emitted from the world's consumption of fossil fuels, and the fight to control global emissions will be won or lost elsewhere. Australia's participation will be by wise conselt and by example. In view of the uncertainties involved, it appears premature to take actions that might place an additional financial burden on our hard-pressed country. However, much can be done now that makes good economic sense and has the added benefit of limiting the growth in Australia's CO2 emissions. Natural gas emits less C02 per unit of energy when burned than either coal or oil. Furthermore, new gas-fired power stations utilise energy at considerably higher efficiency than is the case today with coal or oil. Because of much lower capital costs, there is a compelling economic case for permitting natural gas to compete freely with coal in the Australian power generation market.

Jan 1, 1989

After a short presentation of the Division of Mining at the Royal Insti- tute of Technology, Stockholm, Sweden, the author presents some of-the fill research carried out at the Division. Literature surveys and testing methods and equipment are described. The use of flocculants' in hydraulic filling has been tested both in laboratory and in mines and the results are very promi- sing. Finally compressibility investi- gations and some finite element calcu- lations are presented.

Jan 1, 1973

By M Yahyaei, F Reyes, R Lage, V Jokovic

Equipment wear is strongly related to the performance of grinding circuits. In particular, SAG mills are subjected to the wear of their shell liners and grates. Changes in lifter height and face angle impact mill performance, while classification at the mill discharge is also affected as grates wear out. Moreover, liner mass loss caused by wear affects how operators interpret readings of sensors such as load cells or bearings pressure. Automating and optimising grinding circuits under these constrain becomes challenging due to the nonlinear and dynamic nature of the system. The operation of SAG mill grinding circuits remains largely dependent on human intervention, which frequently results in inconsistencies in performance across shifts, reflecting the operator’s personal preferences, experience, and other human factors. The influence of human factors can be reduced by careful training of operators as well as by automation using advanced supervisory control. The latter approaches could benefit from the development of dynamic process models that consider the effects of wear on the performance of equipment over time. This paper presents detailed industrial data showing the effects of wear on SAG mill performance. Additionally, a dynamic SAG mill model that accounts for these phenomena is proposed and demonstrated in a simulated environment. This model is shown to mimic the effect of wear on the performance of industrial scale mills and the operational constraints they are subject to, thus extending traditional SAG mill models. Incorporating wear into modelling and simulation platforms can improve the understanding of the effects that wear can have on the performance of key assets in comminution circuits and may allow the development of more robust model-based advanced process control strategies.

Aug 24, 2022

By G Reynolds, L Lu

Queensland Pacific Metals (QPM) is developing its flagship Townsville Energy Chemicals Hub (TECH) facility to produce nickel and cobalt sulfates from imported high-grade nickel laterite ore for nickel-cobalt-aluminium and nickel-cobalt-manganese Li-ion batteries. The TECH facility is expected to use a patented leaching, recovery and recycling process called the DNi Process™. It uses the nitric acid leaching process for extracting nickel, cobalt and other valuable metals from laterite ore. Apart from the nickel and cobalt sulfates, the TECH Project will also produce high purity alumina, hematite (~640 ktpa) and other by-products. The hematite by-product precipitated from the DNi Process™ (hematite precipitate hereafter), is high in Fe and particularly low in impurities. QPM is working to identify potential applications for these high-purity by-products to generate additional revenue and to achieve its zero-waste ambition. As such, QPM has engaged CSIRO to evaluate various agglomeration options to produce low-cost, hematitic products suitable as ironmaking feed materials. This paper will first reveal the unique characteristics of the hematite precipitate arising from the TECH Project and then examine the sintering and pelletising processes for preparing the hematite precipitate as an ironmaking feed.

Sep 18, 2023

By J Yamatomi, Y Tamanishi, S Miwa

The four-dimensional (4D) network relaxation method, originally developed by Akaike in 1999, uses Lagrange relaxation and is known for its ability to include the price change and possible better outputs, but the computation time is huge. However, the continuous advancement in computer technologies allows the use of higher-speed computers with more memory capacity. Therefore, in this paper the authors have tried to implement the method with adjustments and improvements in its algorithm to suit the current computing system. As a result, the computation time has been drastically reduced and more constraints can be included, which makes the scheduling a more realistic one. The case study of an open pit gold mine with 129 500 blocks can be solved considering the capacity constraints in 71 seconds. In previous case studies, the mined ore had to be processed or disposed of immediately. Now, stockpiling can be included as another option. Since the details of the algorithm are still being improved, the computation time is a little longer than the previous cases without the stockpiling option. However, it is found that scheduling with the stockpiling option is possible in a reasonable time. In conclusion, the 4D network relaxation method has become more useful with advances in computer technologies and provides better results.

Sep 26, 2011

By M Alston

Organisations’ incident classification processes are plagued by the overclassification of events, often leading to excessive workloads and suboptimal outcomes. This presentation addresses the pressing need to rethink how incidents are classified to maximise organisational learning and minimise systemic risk. A major issue in the current incident classification landscape is the tendency to classify events at high levels, overwhelming organisations with investigations they cannot efficiently handle. This results in inadequate risk reduction and learning opportunities. The link between injury classification and investigation methods further compounds these problems, creating unnecessary administrative clutter. Challenging the misconception that every event, no matter how minor, requires a comprehensive investigation, this presentation advocates for a shift in perspective. The key recommendation is to decouple injury classification and risk matrices from the decision-making process regarding what and how to investigate. Instead, the emphasis should be placed on identifying opportunities for organisational learning and risk reduction. Organisations can streamline their incident management processes by adopting a more pragmatic approach that aligns incident classification with the organisation’s investigation capacity. This transformation focuses on achieving meaningful outcomes, enhancing safety and improving performance. This presentation provides an innovative process for organisations to revamp their incident classification practices, enabling them to harness the full potential of incident data for learning and risk mitigation. It highlights the importance of aligning incident classification with the opportunity for organisational learning, ultimately leading to more effective incident management and enhanced safety outcomes.

Apr 16, 2024

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15 000 tpa magnesium alloy production facility in Nanjing, China. Site construction commenced in February 2005, with installation of all major components completed by the end of October 2005. Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005. Since that time, ramp-up to the name plate capacity has been undertaken. This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By S van der Sluijs, M van Ende, Y Tang, A Emami

This paper presents a phenomena-based model for investigating the possibility of scrap melting in an Open Slag Bath Furnace (OSBF) for green ironmaking. The goal of this study is to enhance the circularity of the steelmaking process by utilising scrap as a green source of iron in OSBFs. The model takes into account the fundamental differences between OSBFs and traditional processes such as Electric Arc Furnaces (EAFs) and Basic Oxygen Furnaces (BOFs). The model considers three primary regions where scrap heating and melting occur: the solid feed pile, slag and hot metal. It accounts for factors such as the furnace geometry, scrap charging mechanism and specific heat and mass transfer properties of the reactor. The model was validated using literature data and was used to investigate the heating and melting behaviour of individual scrap particles under various process parameters. The study finds that the scrap melting process in OSBFs involves three stages: shell formation, shell remelting and subsequent melting of the parent scrap. The carbon content of the scrap and the liquid hot metal plays a critical role in determining the melting behaviour. Depending on the carbon concentration and temperature, the melting process can be heat transfer controlled or mass transfer controlled. The paper also examines the scrap feeding methods in OSBFs, including direct charging into the slag or charging through a feed pile. The model provides insights into the melting rate of scrap compared to Direct Reduced Iron (DRI) in OSBFs and highlights the role of carbon in this process. Overall, this phenomena-based model contributes to the understanding of scrap melting behaviour in OSBFs and provides valuable insights for optimising the circularity and efficiency of green ironmaking processes. The findings of this study can inform the design and operation of OSBFs, paving the way for increased utilisation of scrap as a sustainable feedstock in the steel industry.

Jun 19, 2024

By Y-B Kang, W-Y Cha, Y-M Cho

Molten slag used in the secondary refining process (RH process) for the production of Ultra-Low C (ULC) steel is typically composed of CaO-Al2O3-MgOsat.-FetO with minor constituents. FetO in the RH slag is the main source of reoxidation of the molten ULC steel in the ladle by 2Al + 3(FetO) = (Al2O3) + 3Fe, thereby serving as the source of the alumina inclusions. On the other hand, FetO also enhances the fluidity of the slag, thereby increasing inclusion absorption capacity. Optimum slag chemistry design is therefore required to produce clear ULC steel. The reoxidation kinetics was investigated in the present study by employing high-temperature experiments and developing the reaction rate model. Initial compositions of slag ((% CaO)0/(% Al2O3)0 and (% FetO)0)) and reaction temperature were varied and change of [% Al] in the molten steel was measured. The rate-controlling step was analysed. It was found that the rate-controlling step in some cases changed during the reoxidation: from a mass transport of Al in the molten steel to a mixed transport including Al2O3 in the molten slag. The experimental data validated the reaction rate model based on the elucidated reaction mechanism and FactSage thermodynamic database. The model suggested that high (% CaO)0/(% Al2O3)0 suppresses the reoxidation only when (% FetO)0 is low (5 or lower in the present study).

Jun 19, 2024

By J Rola

This paper outlines a laboratory-based design method, founded in critical state soil mechanics, for identification of an appropriate compaction specification to ensure dilative conditions prevail across the design TSF stress range. The method makes use of the critical state line (CSL) and consolidation tests prepared at varying compactive efforts. The CSL and consolidation curves are plotted together in e-log p’ space, with the compaction curves transformed from vertical effective stress to mean effective stress using the coefficient of earth pressure at rest (K0). Consideration is given to the sensitivity of K0 as it is generally not available during the design phase. An example of the design method is illustrated with laboratory data.

Jul 1, 2021