Search Documents

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951

By F. F. Aplan, D. W. Fuerstenau

This chapter presents modern concepts of the flotation of nonmetallic minerals. In particular, it is concerned with such minerals as metal oxides, silicates, sulfates, carbonates, and halides. It is not the purpose to duplicate the two excellent, recent treatises by Gaudin l and by Sutherland and ark,^ but rather to expand their correlations of data, particularly in view of recent, ex- citing new experiments which are shedding new light on the principles of non- metallic flotation. Outstanding success has been achieved over the past 50 years in separating one sulfide from another or from the gangue constituents using a minimal amount of reagents. In contrast to this, selective flotation in nonmetallic systems is often difficult in that one class of compounds alone, the carboxylic acids, may float nearly the entire array of nonmetallic minerals under the appropriate conditions. Moreover, while lime, cyanide, sodium sulfide, and copper sulfate constitute the principal modifiers used to obtain selectivity among the various sulfides, the nonmetallic mineral flotation engineer is con- fronted with a vast array of modifying reagents. In sulfide and native-metal flotation, a strong chemical adsorptive bond is generally formed between the mineral and sulfhydral collector. In fact, re- cent radio-tracer studies show that below monolayer coverage as much as 98% of added mercaptan is adsorbed on the surface of gold.? Contrasted to this, Bloecher's data indicate that for the quartz-amine system only about 60% of the collector is adsorbed.4 This greater residual concentration in the solution results from weaker forces of adsorption in the quartz-amine system. In the flotation of nonmetallic oxide minerals, collector adsorption results from rather weak physical forces, primarily electrostatic attraction and van der Waals attraction between hydrocarbon chains. In the flotation of salt-type minerals, carboxylic acids are adsorbed both by physical and chemical forces. It is a study of the effect of the electrical forces superimposed on the chemical adsorptive forces that contributes most toward understanding nonmetallic mineral flotation. The need for quantification of general rules for the flotation of nonmetallic minerals is so great that Taggart 5 with unmasked sarcasm suggested that after trying anionic and cationic collectors:

Jan 1, 1962

By D. G. Swarthout, J. W. Savage, R. W. Guard

The Nb-N constitution diagvam has been examined from 1100° to 1450°C at 1 atm N2 pressure. On the basis of- our work plus that of Brauer and coworkers the stable nitvide Phases are: a) a solid solutlion, basic niobium (bcc) with nitrogen contained interstitially; NbN,, x = <0.40; b) ß NhNx,x = 0.39 to 0.45; hexagonal (W2C type) (NbzN); a =3.058A,c = 4.961 + 0.001A c) y NbNx x = 0.75 to 0.80; tetragonal (distorted NaCl type) (Nb4N3); a = 4.386A,c = 4.332 + 0.001A; d) 6 NbN,, x = 0.88 to 0.91; cubic (NaCl type); a = 4.3885 + 0.0007A; e) E NbNx x = 0.92 to 1.00; hexagonal (Tip type); a = 2.958A, c = 11.272 * 0.0015A. In addition, a metastuble transition phase 6&apos; has been observed and occurs only during the transition 6 — E. 6&apos; NbN has these distinguishing parameters: NbNx,x = 0.96; hexagonal (anti-NiAs type); a = 2.94A, c = 5 .46A. The high-temperature phase fields in the system are governed by two reactions: a) 6 + Y + E, a entectoid reaction occurring at 1270" ± 20° C; b) o + N2 = E, a 2 012 1 reaction occurring at 1370" ± 20° C. As part of a study of the electronic low-temperature. properties of transition metal nitrides, a number of specimens of niobium nitride were prepared. Preliminary observations on these specimens showed several points of disagreement with data already in the literature. It was, therefore, decided to determine the constitution diagram for the Nb-N system between 1100" and 1450°C. The objective of this research was to define the temperature and composition regions of stability of the various phases and to explain the differences among previously proposed diagrams. Review of Previous Literature. The research on the Nb-N system to 1964 has been summarized by storms.&apos; Although he does not present a phase diagram, his review covers the research on the system thoroughly. One of the earliest works on NbN is that of Ascher-mann and coworkers2 who studied the superconductivity of the cubic 6 NbN. Subsequent work by Horn and ziegler,3 Cook, Zemansky, and Boorse,1 Rögener:5 Schroder6 and sellmaier7 has qualitatively confirmed the first results on superconductivity, although their methods of preparation differed considerably. The constitution diagrams proposed for the system by Brauer and Esselborn8 and Elliott9 are shown in Fig. l(a)and (b). The diagram in l(a) has been modified by more recent results in Brauer&apos;s laboratory (private communication). Although 6&apos; is shown on this diagram, Brauer has indicated that he now believes 6&apos; to be a metastable phase in the temperature range shown. The diagram of Elliott, Fig. l(b), is based primarily on the results of Elliott and Komjathy10 on ni-trided niobium strip or rod specimens examined by X-ray diffraction and metallography. It will be noted that these proposed diagrams are in conflict with respect to the temperature and composition ranges of

Jan 1, 1968

By E. A. Gulbransen, K. F. Andrew

The vacuum-microbalance method was used to study the oxidation behavior of Zircaloy-2 and -3A over the temperature range of 300 to 850°C and at 0.1 atm pressure. The results fit in well with the authors&apos; earlier studies on zirconium. Tin was found to increase the rate of oxidation and also the temperature at which the metal burns. Both the cubic-rate law and the parabolic-rate law gave imperfect fits to the rate data. Since the parabolic-rate law has been derived from accepted physical principles, this rate law was used to interpret the rate data. A heat of activation of 28,600 cal per mole was calculated. The transition phenomenon previously observed in hot-water and steam-corrosion processes was studied systematically for oxygen atmospheres. Observations on the rate of oxidation, color and properties of the oxide films show that the transition phenomenon was associated with a failure in the adherence of the oxide to the alloy. ZIRCALOY-2 and -3A have found important uses in the field of reactor metals due to their low neutron adsorption, good strength and good resistance to corrosion. One feature of the corrosion reaction in steam or hot water is the sharp transition in the rate of corrosion to a higher value after a certain amount of reaction has occurred. This paper presents a study of the reaction of Zircaloy-2 and -3A with oxygen including a study of the transition phenomenon which has been found to occur also in oxygen atmospheres. A comparison will be made between the oxidation behavior of these alloys and the pure metal. It was hoped that a study of the details of the oxygen reaction would lead to a better understanding of the reactions occurring in hot-water and steam atmospheres. Literature Kinetics-—The reaction of Zircaloy-2 and -3A with hot-water and steam atmospheres has been studied by Thomas.&apos; Goldman and Thomas,&apos; Thomas and Forscher," and Thomas and Kass.&apos; Empirical equations for the kinetics of the reaction have been given by Thomas and Forscher." The change from the initial slow rate of reaction to the final rapid rate of reaction has been termed transition with the post-transition corrosion kinetics following a simple linear equation in time. The corrosion behavior in high-temperature steam was similar in many features to the corrosion in high-temperature water. Goldman and Thomas&apos; and Pray and Peoples&apos; have shown that the addition of tin, while increasing the rate of corrosion, counteracts the deleterious effect of nitrogen. The beneficial effect of iron, nickel and chromium was to improve the adhesion of the oxide to the metal as well as to counteract the deleterious effect of nitrogen. Mallet and Albrecht" have studied the oxidation of two zirconium-tin alloys. The cubic-rate law was found to fit the oxidation data for the 1.5 pct tin alloy while the parabolic-rate law was found to fit the data for the 2.5 pct alloy. Kendall&apos; in a recent paper has studied the oxidation of Zircaloy-2 containing 1.5 pct tin in air atmospheres. Transition Phenomenon—In steam atmospheres Thomas&apos; has observed fora 1.8 pct tin alloy containing small amounts of iron, nickel and chromium that transition to a more rapid rate of corrosion at 400°C

Jan 1, 1959

By T. D. Teimann, R. L. Stone

The rate of extraction of silica from certain Wisconsin and Minnesota taconites was investigated by autoclave digestion in sodium hydroxide solutions over the temperature range from 296° to 416°F. Rates obtained were from 7 to 254 g mol per cm2 per sec giving activation energies from 15,000 to 19.000 cal per mol. Activation energy was found to increase with increase of sodium hydroxide concentration. Digestion of different forms of quartz indicated the rate of extraction to be solely a function of surface area under similar conditions of digestion. The results of an experimental investigation on the caustic extraction of silica from certain Wisconsin and Minnesota taconites were presented in a recent publication.&apos; It was shown that residual concentrates containing as much as 65% iron can be produced by this method. The occurrence of silica as a micro-crystalline variety of quartz with high specific surface area gave correspondingly high mean rates of extraction in solutions of sodium hydroxide. The present paper extends this previous work by presenting the results of a study of the specific rates of extraction of silica from these ores as related to temperature, sodium hydroxide concentration and variety of quartz. Calculated activation energies for the dissolution of silica are presented and some possible mechanisms are discussed. TACONITES The low-grade siliceous iron ores investigated included taconite from the Wisconsin Gogebic range and a semi-taconite2 from the Minnesota Mesabi range. These are adequately described in the former paper1 and by the U. S. Bureau of Mines. The principal iron minerals are hematite (Fe2O3) and goethite (Fe2O3 . H2O), while the gangue is essentially a microcrystalline variety of quartz. Minor amounts of other minerals are present. Typical analyses show the Wisconsin taconite to contain approximately 28% Fe and 54% SiO2 and the Minnesota semi-taconite 39% Fe and 39% SiO2. Analyses of the actual samples used are given in Table I. The taconite samples were prepared for digestion by reducing the original ore to minus 200 mesh in a Braun pulverizer. QUARTZ Three varieties of quartz were studied in the investigation: Ottawa sand, chert and chalcedony. The Ottawa sand was obtained from the Ottawa Silica Co. The chert and chalcedony came from Wards Natural Science Establishment. A minus 200 plus 400 mesh fraction of the Ottawa sand, used as a surface area standard, was repeatedly washed in hot concentrated hydrochloric acid followed by distilled water before autoclaving. The other two varieties were used directly after grinding through 200 mesh in a laboratory hammer mill. Analyses of these samples appear in Table 11. Microscopic examination of the silica samples by the oil immersion method showed that the Ottawa sand consisted of clean, uniform spheres of quartz with little deviation in size from a mean diameter of 82µ determined by a distribution count. The other two varieties consisted almost entirely of microcrystalline aggregates of quartz crystals; the aggregates ranged from 10 to 70µ. The individual crystals in the chert aggregates were estimated to be of the order of

Jan 1, 1964

Discussion of the paper of CHARLES T. MALCOLMSON, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 271 to 289. E. W. PARKER, Washington, D. C.-The briquet or boulet, or coalette (whatever name is used) has come to stay as a part of the fuel supply, particularly for domestic purposes. During the past winter I have had some personal experience with the use of boulets made from anthracite coal. All of this winter I have used boulets in my furnacee and in my grate at my home in Washington. One reason for doing so is that we get the boulets at a price considerably cheaper than the prepared sizes of anthracite coal. The fuel has proved entirely satisfactory. One advantage possessed by the boulet is its absolutely uniform size, which makes the ventilation of the firebed practically perfect. The boulets burn until entirely consumed. There is not, even in an open grate fire, if the fire is kept constantly going, any unconsumed fuel passing through the grate bars. The boulets hold their form until entirely consumed and then break away into a clean white ash, with absolutely no clinker. That in itself is a particularly favorable recommendation to the housekeeper. Mr. Malcolmson has mentioned the fact that notwithstanding the smokeless character of anthracite, the boulets made from it emit smoke. The emission of smoke is due to the coal-tar pitch used as a binder. This is particularly noticeable if the fireman is somewhat careless, or wants to save labor, and feeds too much of the fuel on the fire at one time, cooling it down and thus causing an unnecessary amount of smoke. The smoke lasts but a short time, however, and if the fire is fed a little more frequently, with a small quantity of fuel at one time, the smoke is reduced to a minimum. I believe it will not be long before some of our engineers will have overcome the objectionable smoke; and will produce either from anthracite or from the so-called smokeless New River and Pocahontas semi-bituminous coals, a briquet which will be as smokeless as anthracite for all. practical purposes.

Jan 5, 1915

By T. D. Murphy

The element silicon, with its usual partner, oxygen, plays the same role on this planet relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO,) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO, tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature&apos;s cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide SiO, (analogous to its congener carbon in CO and CO,); a tetrachloride SiCl, (analogous to CC1,); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117°- 200°C but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures-such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao, et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert, et al., 1973; Pecora, 1960).

Jan 1, 1975

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum were grown by multipass zone melting in an electron beam apparatus. Tension tests of these crystals at 4.2 x 10&apos;* per sec-gave a resolved louler yield stress of 7300 psi at with a chisel edge; total uniform deformation increased from 1 to 2 pct at 77°K to over 20 pct at 300°K. This, and slip traces, indicated that deformation is more inhomogeneous at lower temperatures. Deformation occurred exclusively by slip in <III> directions, on planes in the <111> zones. Cross slip was frequent, particularly for those orientations where the resolved shear stress on the cross system was comparable with that on the primary plane. The existence and magnitude of the upper yield point were found to be sensitive to orientation. This effect was related to the circumvention of dislocations which were "locked" by interstitial atoms, by double cross slip, or composite slip, of screw dislocations. Prestrainirg at 300°K did not remove the upper yield point in subsequent tension at 77°K. Also, this treatment was found to cause yield points, where none existed for the unprestrained material. This behavior was also rationalized in terms of the circumvention mechanism. The mechanical properties of polycrystalline tantalum have been investigated by several workers,1"4 and may be summarized by pointing out the following features: a) Sharp rise of yield stress with decreasing temperature below room temperature. b) Response to strain aging at 300" to 400"C. c) Yielding with upper and lower yield-point phenomenon at and below room temperature. d) Low strain hardening below room temperature. e) Reluctance to twin except at very high strain rate. Furthermore, tantalum is ductile at ordinary strain rates as low as 4.2"K.&apos; This feature, in particular, makes tantalum unique among the high melting point, bee transition metals of Groups V and VI in the periodic system. Therefore, a more fundamental and detailed knowledge of the low-tempera- ture deformation of tantalum is required. Since high purity and the absence of grain boundary effects make such a study most productive and unambiguous, the method of electron beam zone melting was selected for the preparation of test specimens. This technique has the further advantage that crystals may be seeded in order to obtain any desired orientation. EXPERIMENTAL The electron beam zone-melting equipment was constructed as a modification of that described by Calverley, Davis, and Lever? All crystals were made by three passes of the molten zone at 4 mm per min to achieve an optimum purity commensurate with economy of time and material. Table I reports the chemical analyses of the starting and refined metal. It will be noted that there remain some 50 to 70 wt ppm of interstitial elements, while all substi-tutional elements have been removed by evaporation. Tungsten is picked up by evaporation of the cathode filament wire. Crystal seeding was normally successful within 3 deg, and the orientation of all crystals are given in the standard stereographic triangle in Fig. 1. Tensile bars were prepared from the crystals by centerless grinding to the shape in Fig. 2. Specimens were then electropolished to remove 10 pct of the diameter in order to remove worked material and to prepare a metallographic surface for subsequent deformation trace observations. All specimens were held in the split bushing grips as indicated in the cross section view of Fig. 2. All tests were made at a strain rate of 2 112 pct per min in an Instron testing machine.

Jan 1, 1962

Jan 1, 1920

By J. P. Heller

The purpose of this discussion is to comment briefly on one of the points raised in the paper. The topic is that referred to in the Conclusion 2, in which the authors note a "disproportionate increase in mixing rate" as they proceed from a displacement performed at viscosity ratio 0.998 to one at 1.002. The recovery curve of this displacement, Fig.2A, shows a quite noticeable difference between the two runs in which displaced and displacing liquids were interchanged. This difference is ascribed by the authors to the change in viscosity ratio between the two experiments. This interpretation of the experimental results must certainly be based on rather precise measurements of the fluid viscosities or, at least, of the ratio of their viscosities. The ordinary Ostwald viscometer, employed in the usual way, is only just able to distinguish between liquids whose viscosities differ by two or three parts per thousand. The experimental refinements which then must have been necessary to measure with any precision a viscosity ratio of 1.002 would be worthy of mention. Indeed, one would have expected the authors to devote at least a paragraph to the display of this technique. For the same reason - to emphasize that the details of such unusually critical experimental work should be reported and discussed in the literature — I would have liked to see some comment by the authors on the requirements for temperature control during both the viscosity measurements and the displacement experiments. The temperature coefficient of viscosity of Soltrol C at room temperature has been measured in this laboratory at about - 1.9%/1°C. How much did the coefficients for the fluid mixtures used in the experiment differ from this and from each other Even if the two fluids were identical in this respect, it would appear that a temperature difference of .l°C between them in the flow system would produce a viscosity con- trast equal to that imposed by their composition. Reference to the experimental solutions of these problems would render Conclusion 2 more credible. Published theoretical work on the stability problem contains no indication of such extreme sensitivity to the viscosity ratio in the immediate neighborhood of unity. On the contrary, perturbation calculations such as those made by Chuoke1 and Perrine2 lead to initial finger growth rates proportional to the first power of the viscosity difference. The later instability growth calculated by Scheidegger,3 using the assumption of zero pressure gradient perpendicular to the average flow, is also simply proportional to the viscosity difference. The conflict regarding the sensitivity of the dependence of instability growth or mixing rate on the viscosity contrast needs explicit recognition in the literature. In particular, it would seem that the experimental work reported here should be supported by a more detailed description of the viscosity controls. Further discussion of possible alternative interpretations of the data would also be in order. For instance, is it possible that the unconsolidstted bead pack used changed its characteristics between the runs (due, perhaps, to the handling and inverting involved in the injection of the front) Or, are the data points of Fig. 2A averages from several runs performed in a series in which the two liquids alternated as displaced and displacing fluids? To summarize, it seems to me that the relationship asserted by Conclusion 2 in the paper needs the support of more detailed experimental evidence. REFERENCES 1. Chouke, R. L., van Mews, P. and van der Poel, C.: "The Instability of Slow Immiscible Viscous Liquid-Liquid Displacements in Porous Media", Trans., AIME (1959) Vol. 216, 188.

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By John Buch

NEARLY 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining under-lying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading&apos; was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechan-ical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1939

By Rossiter W. Raymond

In the course of this address, President Raymond referred to the law, said to have been discovered at the French works of Terrenoire, that the amount of phosphorus may be increased without injury to steel, if the amount of carbon be proportionately decreased. The works named have been for more than a year, it is said, manufacturing in the open hearth, by the Martin process, steel rails containing as high as 0.35 per cent. of phosphorus, with about 0.15 per cent. of carbon, which were not found inferior to Bessemer rails. It is not claimed by the manager of the works that phosphorus is an ingredient to be preferred, or purposely introduced; but only that materials containing it (such as old iron rails, etc.), can be succesfully employed. Other parties have apparently a higher opinion still of the new manipulation, and are prepared to claim for " phosphorus steel" superior qualities. Mr. I. Lowthian Bell alluded to the subject in his recent address as President of the British Iron and Steel Institute, but without expressing a positive opinion. After pointing out that the commercial value of the process turned on the cheap manufacture of ferro-manganese, by means of which only could the necessary amount of manganese be introduced into the Martin bath, without increasing its contents of carbon, Mr. Raymond proceeded to say that the principle alleged to have been discovered at Terrenoire was already known years ago, in this country, at least. Not only had steel been manufactured here, containing high percentages of phosphorus, coupled with low percentages of carbon, and suitable for use in rails, boiler-plates, etc., but the reason of its surprising qualities had been distinctly surmised, if not widely proclaimed. The following analyses and extracts from private letters prove these assertions. Some of them assert a similar principle in .the case of wrought iron; but the analyses, and the remarks based upon them, have reference solely to the steel manufactured under the superintendence of Mr. Slade, at the works of the New Jersey Steel and Iron Company in Trenton.

By Rossiter W. Ph. D. Raymond

(From the President&apos;s Address at St. Louis, 1874.) IN the course of this address, President Raymond referred to the law, said to have been discovered at the French works of Terrenoire, that the amount of phosphorus may be increased without injury to steel, if the amount of carbon be proportionately decreased. The works named have been for more than a year, it is said, manufacturing in the open hearth, by the Martin process, steel rails containing as high as 0.35 per cent. of phosphorus, with about 0.15 per cent. of carbon, which were not found inferior to Bessemer rails. It is not claimed by the manager of the works that phosphorus is an ingredient to be preferred, or purposely introduced; but only that materials containing it (such as old iron rails, etc.), can be succesfully employed. Other parties have apparently a higher opinion still of the new manipulation, and are prepared to claim for "phosphorus steel" superior qualities. Mr. I. Lowthian Bell alluded to the subject in his recent address as President of the British Iron and Steel Institute, but without expressing a positive opinion. After pointing out that the commercial value of the process turned on the cheap manufacture of ferro-manganese, by means of which only could the necessary amount of manganese be introduced into the Martin bath, without increasing its contents of carbon, Mr. Raymond proceeded to say that the principle alleged to have been discovered at Terrenoire was already known years ago, in this country, at least. Not only had steel been manufactured here, containing high percentages of phosphorus, coupled with low percentages of carbon, and suitable for use in rails, boiler-plates, etc., but the reason of its surprising qualities had been distinctly surmised, if not widely proclaimed. The following analyses and extracts from private letters prove these assertions. Some of them assert a similar principle in -the case of wrought iron ; but the analyses, and the remarks based upon them, have reference solely to the steel manufactured under the superintendence of Mr. Slade, at the works of the New Jersey Steel and Iron Company in Trenton.

Jan 1, 1875

By M. E. Fine, A. A. Henderson

Investigation of the tensile properties of silver based aluminum alloy crystals was undertaken because it appeared attractive for studying strengthening effects due to Suzuki locking with minimum complication. Yield drops were observed in all alloy crystals (1, 2. 3. 4, and 6 at. pct Al) after strain aging at room temperature. No yield drops were found in similarly grown and tested silver crystals. The yield effects are attributed to Suzuki locking but the major portion of the solid solution strengthening to other mechanisms. INVESTIGATION of the tensile properties of single crystds of silver alloyed with aluminum was undertaken because it appeared to be a system in which segregation at stacking faults associated with partial dislocations1 would be the dominant factor in anchoring dislocations. First, silver and aluminum have closely similar atomic sizes and thus solute atom locking of a dislocation due to elastic interactions should be unimportant. Second, while both X-ray2 and thermodynamic3 investigations show short-range ordering in silver-based aluminum alloys, the degree of local order is quite small (X-ray measurements give v = EAB - 1/2(EAA + EBB) = - 0.025 ev and thermodynamic measurements give v r -0.007 ev) and should not be important in strengthening dilute alloys. Third, the stacking fault energy of silver is probably low (as indicated by the profusity of annealing twins) and is very likely diminished further and quite rapidly by aluminum additions since the A1-Ag phase diagram shows a stable hexagonal phase at only 25 at. pct Al. Also, a careful investigation in this laboratory4 has shown that the ratio of twin to normal grain boundaries in recrystallized alloys increases with aluminum content. Thus, with minimum complication from other factors, Ag-A1 alloys seem attractive for studying strengthening effects due to segregation at stacking faults of extended dislocations. EXPERIMENTAL METHOD Single crystals measuring 250 by 5 by 1.5 mm of pure Ag (99.99 pct) and Ag-A1 alloys (A1 of 99.999 pct purity) of nominal compositions* 1, 2, 3, 4, and 6 at. pct were grown in high-purity graphite molds from the melt under a dynamic vacuum (1 x l0-5 mm Hg). The technique consisted of moving a furnace having a hot zone (which melted about 0.5 cm of alloy) over a horizontal, evacuated quartz tube con- taining the mold and alloy at a rate of 3/8 in. per hr. Chemical analysis showed roughly the first inch of the crystal to be solute poor, the last inch solute rich; and the center section uniform in composition within the sensitivity of the analytical method (± 0.2 at. pct Al). The center section of the crystal was cut into five specimens. Gage lengths of reduced cross section, measuring from 1.5 to 2 cm in length, were mechanically introduced by means of jeweler&apos;s files and fine abrasive cloth with the crystal firmly held in polished steel guides. One-third of the cross section was then removed by etching and electro-polishing, the crystals were all subsequently annealed for several days at 850°C in a dynamic vacuum (<1 x 10-5 mm Hg) and furnace cooled to 200°C. The crystal orientations were determined using the usual back-reflection Laue technique. The Laue spots were sharp and of the same size as the incident beam. However, microscopic examination showed the crystals to contain substructures with subgrains of the order of a micron in diameter. The details of this substructure are presently under investigation. Tensile testing was done with a table model Instron using a cross-head speed of 0.002 in. per min. For testing at various temperatures the following media were used: 1) 415oK, hot ethylene glycol; 2) 296ºK, air, acetone, water; 3) 273ºK, ice water; 4) 258ºK, ethylene glycol "ice" in ethylene glycol; 5) 200°K, dry ice in acetone; 6) 77ºK, liquid nitrogen. EXPERIMENTAL RESULTS A) Yield Behavior—A portion of an interrupted stress-strain curve for a 6 at. pct A1 crystal of the indicated orientation tested at room temperature is shown in Fig. 1. Initially, at (a), there is a small, gradual yield drop of about 10 mg per sq mm2. However, on stopping the test, and aging for a few minutes at (b), a sharp yield drop is found. Aging for longer times at (c) and (dl results in larger yield drops (and larger AT&apos;S). At, defined in Fig. 1, is usually larger than the yield drop by about 20 pct; however, this increase in the lower yield is transient since extrapolations of the flow stress curves join as may be seen from Fig. 1. (Both Laue and low-angle scattering photographs revealed no evidence of precipitation in a strain-aged 6 at. pct A1 crystal.)

Jan 1, 1962

By M. O. Abo-el Fotoh, J. B. Mitchell, J. E. Dorn

The effect of strain rate and temperature on the tensile flow stress of a polycrystalline bcc alloy of magnesium containing 14 wt pct Li and 1.5 wt pct Al was investigated for strain rates of 3.13 x lom5 to 3.13 x 10-3 per sec over the range from 20° to 300°K. From about 180° to 300°K the alloy exhibited an ather-ma1 deformation behavior where the flow stress was independent of strain rate and increased only slightly with decreasing temperature. At lower temperatures the flow stress was strongly strain-rate- and temperature-dependent, characteristic of deformations controlled by thermally activated mechmzisms. The activation volume for thermally activated plastic defornzation was between 5 and 30 cu Burgers vectors, independent of plastic strain. This low-temperature thermally activated deformation behavior was found lo be in satisfactory agreement with the theoretical dictates of the Dorn-Rajnak1 formulation of the Peierls mechanism where deformation is controlled by the rate of nucleation of pairs of dislocation kinks over the Peierls energy barriers. SEVERAL studies of the low-temperature thermally activated deformation of bcc metals and alloys (molybdenum,1 tantalum,1 Fe-2 pct Mn,2 Fe-11 pct MO,3 and AgMg4) have revealed that the strain rate is controlled by the activation of dislocations over the Peierls-Nabarro energy hills. Although there is some uncertainty as to the nature and effect of solute atom-dislocation interactions during low-temperature deformation of bcc metals, it has been concluded by Dorn and Rajnak,1 Conrad,1 and Christian and Masters6 among others that overcoming the Peierls-Nabarro stress which arises from the variations in bond energies of atoms in the dislocation core as it is displaced is the probable mechanism controlling low-temperature deformation. The purpose of this research was to investigate the low-temperature plastic deformation of the bcc alloy Mg-14 wt pct Li-1.5 wt pct A1 to determine if the behavior of this alkali metal alloy might be analogous to that for other bcc metals. This alloy was selected because of its availability and its current industrial importance as a lightweight material for aircraft and aerospace applications. I) EXPERIMENTAL PROCEDURE Polycrystalline tensile specimens having cylindrical gage sections 2 in. long by 0.2 in. in diam were machined from as-received alloy sheet stock of Mg-14 wt pct Li-1.5 wt pct Al. Specimens were annealed in an argon atmosphere at 423°K for 4 hr and maintained in a kerosene bath together with the sheet stock to prevent corrosion. The resulting specimen microstructure consisted of a coarse uniform dispersion of incoherent precipitate MgLi2Al particles7 in a bcc 0 phase matrix having an average grain size of 150 p. Prior to testing the specimens were chemically polished in dilute hydrochloric acid. Comparison of tensile properties and microstructures of specimens cut from center and edge sections of the sheet stock revealed no effects of inhomogeneities in the sheet material. Tensile tests were performed on an Instron machine at crosshead speeds corresponding to tensile strain rates of 1.56 x 10-5 and 1.56 x 10"3 per sec. Stresses were determined to ±2 x 106 dynes per sq cm and strains to within ±0.0001. Average values of shear stress t and shear strain y reported were taken as one half the tensile stress and three halves the tensile strain, respectively. Flow stresses were taken at 0.05 pct strain offset. Test temperatures down to 77°K were obtained by immersing the specimens in constant-temperature baths. Lower-temperature tests were performed in a liquid helium cryostat to within ±2°K of the reported values. Prior to testing at the various temperatures and strain rates all specimens were prestrained at 2 35°K at a shear strain rate of 3.13 x 10-5 per sec to a stress level of 0.606 x 10&apos; dynes per sq cm to obtain a uniform initial state. Additional tests were made to determine the effect of changes in strain rate and strain on the flow stress by rapidly changing the crosshead motion during testing. Shear moduli of elasticity, needed for analyses of the data, were obtained at several temperatures by a common technique of determining the resonant frequencies of vibrations of rectangular test specimens. 11) EXPERIMENTAL RESULTS Fig. 1 shows the experimentally determined flow stress vs temperature for two strain rates. Two distinct regions of behavior are evident. Below about 180°K the strong increase in flow stress with increased strain rate and decreasing temperature indicates that deformation is controlled by a thermally activated dislocation mechanism. At higher temperatures an athermal region is evident where the flow stress is independent of strain rate and only slightly dependent on temperature. The applied stress t to cause plastic flow was separated into two components:

Jan 1, 1969

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE mechanism by which the super-saturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications. 1,2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon {111} matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;3 at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate y but that of a transition lattice ?&apos;. Since this is also platelike in shape and also lies upon the {111} matrix planes with the {110} direction in the matrix parallel to the {11.0} direction in ?&apos;, it seems likely that the original platelet particles are merely ?&apos; in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the {00.0} plane in ?&apos; are identical with those on the {111} matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures ?&apos; and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, ? &apos; is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system,2,4 hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructure, Brinell hardness and electrical resistivity of the three alloys. PREPARATION OF SAMPLES AND EXPERIMENTAL PROCEDURE The preparation of the 20.2 per cent Ag alloy has been described.2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent Al and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948