Search Documents

By Gunnar Thaning, Goran Mathisson

The iron ores mined by LKAB in the north of Sweden have excellent beneficiation properties. This gives LKAB a favorable position as regards the production of low silica pellets for direct reduction. LKAB has concentrated on developing and marketing grades of pellets for the Midrex-Purofer-HyL process group, i. e., such direct reduction processes carried out in a shaft furnace or a static bed using reformed natural gas as a reducing agent. The paper deals with properties and quality demands of iron ore pellets for such processes. Matters such as the effect of the residual magnetite in the fired pellets on the degree of metallization, the amount and composition of the slag phase in the pellets, the mechanism of the disintegration during reduction, the state of swelling of the pellets during the conditions prevailing in these processes, the importance of the porosity, the improvement of the reducibility and lowering of the sticking tendency of the pellets by small additions of suitable additives, and the influence of the pellet size are discussed. A special test procedure for direct reduction pellets has been elaborated by LKAB. Thus, three metallurgical properties are routinely determined separately, namely reducibility, reduction strength, and sticking. The test methods are described. Finally the present and future LKAB pellets for direct reduction are presented with respect to chemical analyses and metallurgical properties.

Jan 1, 1980

By O. Skiredj, J. F. Elliott

It has been necessary to collate the available data on the solubility of graphite in Fe-Si-Mn alloys for a study of slag-metal equilibria in ferromanganese production. That study will be reported later; the collation is reported here. The carbon content of graphite-saturated liquid iron above 1153ºC by Chipman and co-workers1 is: %C= 1.34 + 2.54 x 10~3t(°C) [l] For graphite-saturated manganese above 1322ºC it is: %C = 2.68 + 3.52 x 1CT3 t(°C) [2]

Jan 1, 1963

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

By William P. Blake

The late Dr. Ebenezer Emmons of Albany, one of the geologists of the Survey of New York and the author of The Taconic System, brought to notice as early as 1838" a peculiar concretionary and lamellar form of phosphate of lime, to which he gave the name Eupyrchroite, from the Greek words for fire and color, with the pefix

Jan 1, 1893

By Guy D. Bruno

Through the remainder of this century, world consumption of fluorine per ton of primary aluminum produced will continue to be substantially reduced. Growth of the primary industry will offset some of the unit consumption, but demand for new fluorine sources will decline sharply. Continued application of dry fume scrubbing systems will be the most significant factor in reducing demand.

Jan 11, 1978

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cureall" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made.

Jan 1, 1950

By A. L. Bailey, B. A. Landry

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally. Of course, the matter is rendered complex by the circumstance that the float-and-sink test, not a simple analytical measurement but a process test, comprehends a number of more-or-less independent items of fundamental data; and as shown in the report, the' variability of the samples differs with respect to these different items. This condition and the wide variety of situations in which float-and-sink test data are used, in combination with other factors, to study complex process operations, indicate the difficulty of setting up fixed standards for float-and-sink sampling and testing. At this stage at least, it is the intent rather to obtain experimental data on the principal Factors involved so that the reader may arrive more intelligently at a procedure adapted to his problem. The authors of this paper have presented experimental data showing the relationship between size of sample and particle size for different variability tolerances with respect to percentage of sink. In further studies, data are being collected to appraise also the variability of the samples with respect to float-ash content and size consist. The scope of this work will be broadened to cover particle sizes up to 4 in., and a third series of tests has yielded similar data for a much cleaner type of raw coal. Thus, the further studies will make available a fairly comprehensive meas- ure of variability with respect to size consist, percentage of sink, percentage of middlings, and percentage of ash in the float, for three coals ranging from 3.87 to 17.68 pct in refuse content (heavy sink material) and from 4.18 to 17.52 pct in middlings. Introduction At present there are no published standards for float-and-sink test sampling. During the rapid expansion of float-and-sink test work, varying procedures have been based on adaptations of the ASTM standards for sampling coal for analyses. For this reason, a special study of gross sample reduction has been undertaken to determine the limits for this step in the operation where no reduction in particle size is to be made before testing. Float-and-sink tests are made whenever a thorough study of coal characteristics is desired. The tests may be made on samples from coal-cleaning units such as jigs or tables, or coal samples may be tested which are taken from a loading boom, railroad car, or the coal seam itself. The resultant gross sample may be large and pose a problem of sample reduction. The question is, then, how much can the sample be reduced and still fall within preassigned limits of accuracy of the original gross sample of coal? Coal from channel samples may be crushed to liberate impurities and then separated into various gravity fractions from which washability curves are drawn; from these curves, it is possible to determine the cleaning characteristics of the coal. However, coal samples from coal-cleaning units cannot be

Jan 1, 1950

By J. M. Lohr

THE characteristics and uses of thermocouples of platinum and the platinum alloys being so well known, this paper will be confined to base-metal couples. During the past decade, there has developed a strong demand for thermocouples made of metals cheaper than the platinum alloys, and suitable for industrial heat measurements. Much research has been clone but only a very limited number of alloys have been found to possess the necessary characteristics for general technical use. In the development of thermocouple alloys it is necessary to consider the following points: The electromotive force and temperature relations; permanency or constancy; reproducibility; manufacturing difficulties; durability; and accuracy in use. The electromotive force developed by the thermocouple should increase with the rise of temperature according to some definite law. It is desirable that the electromotive force should vary directly with the temperature difference of its junctions, in other words, giving a curve linear or nearly so. It is also desirable that the resulting electromotive force be as large as possible for any given range of temperature, thereby insuring greater accuracy of readings.

Jan 9, 1919

By E. P. Mathewson

(Butte Meeting, August, 1913.) IN a discussion -of a paper on " The Basic Process as Applied to Copper Smelting," by Percy C. Gilchrist, read before the Society of Chemical Industry, London, Jan. 5, 1S91,1 Prof. W. C. Roberts Austen asked Mr. Gilchrist whether he thought that the substitution of a basic lining for acid lining in the Marshes process would afford anything like the service which it had been shown to render in the metallurgy, of iron. Claude Vautin stated that he had experimented for over two years with basic linings for Bessemer converters for copper mattes at Cobar, but had given up the attempt on the score of cost. Mr. Gilchrist in his reply stated that he did not believe in applying any system of Bessemerizing to copper. About the time of the presentation of the paper mentioned, Herman Keller, Superintendent of the Parrott smelter, in Butte, was experimenting on a large scale with converters lined with magnesite brick. He gave up the idea on account of the cost of linings and because no particular advantage was observed. My belief is that his tuyeres and converters were -too small. A short time; afterward similar experiments were tried at the Great Falls plant of the Boston & Montana Co., said at the Old Works of the Anaconda Copper Mining Co. in Anaconda. These were abandoned on the score of cost and the lack of advantages. The same cause of failure, in my opinion, holds here. The Anaconda Copper Mining Co., however, adopted the magnesite brick lining for its tilting casting machines.

Jan 6, 1913

By G. A. Parks, C. Kovacs

The xanthate flotation of chrysocolla can be improved by preheating the ore to 500° to 600°C. Addition of water vapor reduces the preheating temperature required. The temperature range of flotation improvement correlates well with the range over which dehydroxylation occurs. This observation is consistent with changes in the structure and properties of the mineral as detected by measurement of solubility, D.T.A., T.G.A., X-ray diffraction, and infrared absorption and with recently proposed explanations of chrysocolla flotation. A brief experiment by one of the authors several years ago showed that exposure of chrysocolla to high temperature water vapor resulted in increased recovery by subsequent xanthate flotation. Recently renewed interest in flotation and thermal properties of chrysocolla1-5 prompted further study of this effect and more detailed reporting.6 This paper explores the response of pure chrysocolla recovery in Hallimond tube flotation tests to the time and temperature of exposure and to changes in the water vapor pressure. Brief attention is paid to the effects of such treatment on accessory minerals. A single experiment with flotation of chrysocolla from an ore is reported. MATERIALS Chysocolla from Inspiration, Gila County, Ariz. was crushed in a porcelain mortar, cleaned of visible and magnetic impurities, and screened to obtain -48 +65 mesh (Tyler) material for flotation test work. The clean material contained 28.5% Cu and was identified as chrysocolla by comparison of X-ray diffraction, D.T.A., and infrared absorption data with that reported for similar materials by others.4,5,7 Samples of malachite and chalcopyrite, prepared in a similar way, were also identified by X-ray diffraction. The sources of these materials are unknown. A sample of chysocolla-bearing oxidized copper ore from Pima, Ariz. was crushed and dry ground for thermal activation and subsequent flotation. PROCEDURES Activation: The apparatus used for exposure of materials to high temperature water vapor is illustrated in Fig. 1. The furnace temperature was controlled to ±5°C Water vapor pressure was controlled by pre-saturating a nitrogen carrier stream with water in an adjustable thermostatted saturator (multiple bubbler). A water manometer and capillary orifice flow meter were used to measure nitrogen flow rates for activation and for subsequent Hallimond tube tests. Gas flow rate and temperature were adjusted prior to introduction of samples. Exposure time was measured from the moment of introduction of the sample to the furnace, hence includes an initial drop below the control temperature. After heating, the samples were removed from the furnace and stored at room temperature in air. Representative samples of activated materials were examined by X-ray diffraction and infrared absorption.

Jan 1, 1967

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger; because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field. which furnishes us

Jan 1, 1927

By W. Fletcher, R. C. Schenk

This paper outlines a well proven and highly successful approach for eliminating many of the problem and frustrations often experienced in plant startup. The approach was developed over a period of 25 years during which some 90 plants were commissioned. This paper discusses startup from the contractor’s perspective and highlights the requirement for detailed startup planning, careful coordination during the project final construction phase, and thorough checkout of equipment prior to introduction of feed. Performance of these services has demonstrated a valuable opportunity exists for the contractor to assist in the training of the plant operating personnel.

Jan 1, 1983

By Jan M. Mutmansky

Main purpose of the research described is to apply the method of computer simulation to the process of tunneling by rapid excavation methods. Primary attention was focused on the materials handling subsystem because of its potential for improvement from a systems standpoint. A description is given of the computer model and a summary of some applications of the model for improving the rapid excavation process is included.

Jan 1, 1975

By Sinha D. K.

As the main source of indigineous energy, coal has a big role to play in the development of national economy of India. Nationalization of the coal mining has brought the entire industry under the unit control of the Central Government following which an ambitious plan for increasing the coal production in the next few five year plans has been undertaken. In order to achieve best all round results, economy-mathematical models of Planning the total system, right from the highest to lowest hierarchial levels of decision making, have been proposed through a Global Model which is detailed in Local Models in stages right up to a mine. Optimum obtained by computer solution of the models would provide basis for objective decision making in the fields of selection of optimum plan for developing the industry, the coal fields and the mines with construction and/or reconstruction of mines, capacity optimization of enterprises and mines therein. Different types of Models and the optimization processes are presented.

Jan 1, 1977

By Robert J. Brison

On the basis of experience accumulated during the completion of some 150 gold/silver process development projects, general guidelines are presented for developing the most cost effective process for a specific project. Steps involved in process development for lode ore deposits generally include a review of pertinent background information on the ore deposit, sample procurement and preparation, sample characterization, study of concentration possibilities, investigation of leaching and metal recovery methods, economic evaluation of alternative processes, optimization of the selected process, a pilot plant program if warranted, and finally, process design and feasibility studies. Each of these steps is discussed, with emphasis on the relation between technology and economics.

Jan 1, 1984

By Wilbur Stout

IN Ohio, the annual output of coke made from native coals has averaged not more than 70,000 tons, or about enough to run a 200-ton blast furnace. Raw coal locally mined from the Sharon, or No. 1, bed was used for iron smelting in Mahoning furnace at Lowellville, Mahoning Co., as early as 1846. This practice was continued in the Youngstown district until the coal became scarce and the Connellsville coke more popular. At present, the Sharon bed contributes a part of the fuel for the production of ferrosilicon iron at Jackson, Jackson Co. About one-third native coal and two-thirds soft coal are used. In this state, coke, on a commercial basis, was first made in Jefferson County probably about 1861 or 1862. The coals used were the Steubenville Shaft, or Lower Freeport, and the Strip Vein or Middle Kittanning. The practice, however, was discontinued before 1880 because of the competition of superior foreign cokes. Beehive ovens, later built at Leetonia, Columbiana Co., were operated for only a few years; the coal used at this place is the Lower Kittanning or No. 5. In a desultory way, slack from the Pittsburgh coal has been coked at a few places in eastern Ohio, and attempts, either for experimental or for commercial purposes, have been made in other parts of the State. Small quantities of coke were made from the Upper. Freeport coal at Salineville, Columbiana Co., and near Nelsonville, Hocking Co.; the results were poor. Tests were made of the Middle Kittanning coal near Zanesville, Muskingum Co., at Moxahala Furnace, Perry Co., and at Washington Furnace, Lawrence Co.; the cokes were all high in sulfur and ash. Attempts were made to coke the Clarion coal at Vinton Furnace, Vinton Co.; a small battery of molding ovens and a pile of high-sulfur coke yet remain to tell the story. The Pittsburgh coal was coked on a commercial scale at Utley and at Lathrop, Athens Co.; but the operations were not successful and were soon abandoned.

Jan 9, 1919

By Ralph Wilcox

THE diamond drilling of certain characters of unstable rock forma-tion, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as " caving" of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving-with resultant difficulties, such as decreased speed of sinking and increased consumption. of diamonds-would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the outside of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the .drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole.

Jan 10, 1913

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situa-ated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way. If it is definitely established that a plant will be in operation for only a few months, this limited time factor will probably influence the design of the foundation, and rightly so. If sensitive and complickted equipment is to be mounted on these foundations and the plant is to operate for several years, there should be a thorough study of foundations and a very careful design. A familiar problem is presented by the difficulty of operating a permanent plant originally designed for a few months' work. The engineer must beware of these hazards and disassociate himself from them if he cannot prevail on the promoter to spend the proper amount for a thorough foundation study. Laws of certain provinces and states hold the engineer equally responsible with the contractor for any 'damage that may be caused to building through inadequate study-ignordnce of the facts is no excuse in the eyes of the law. Types of Soil: The engineer should be familiar with such terms as silt, clay, peat, and varved clay, as well as perpafrost, especially if he is to work in the far northern reaches of the country. He should also be familiar with soil attributes such as porosity, texture, consistency, permeability, compressibility, consolidation, and shearing resistance. The design of any foundation requires an accurate knowledge of the physical properties and location of the soils involved. Older textbooks on the subject outline various empirical methods to determine the carrying power of soil. Tables are given in reference books. The modern ehgineer should be wary of these modes of thinking. He should analyze his problem carefully, calculate to what depth of soil the loads may be transmitted, and then check the bearing value of all soils to that or greater depths. If the strata are water-carrying, he must determine the possibility of this water being accidentally re-

Jan 1, 1958

By Heinrich A. Kortmann

Specifications on the chemical, physical and metallurgical properties of the blast furnace burden are steadily becoming more stringent, especially in those countries where higher raw material and energy costs can be overcome only by improved technology. This paper describes the test methods for the relative predetermination of the criteria where the effects of temperature, gas composition and physical load in the blast furnace are duly considered. Data are presented to show the correlations between burden material tests and blast furnace results. Possible test methods for the direct reduction process are also discussed.

Jan 1, 1977

By C. S. Barrett, A. Smigelskas

J. T. NORTON*—I think Mrs. Smigelskas Fischer has done a splendid job in working out the pole figures from rather difficult photograms which are common to beryllium. Is there not a mistake in Fig 2 in that the pole figures B and C have been interchanged? A. SMIGELSKAS FISCHER (authors' reply)—Yes, there is such an error in the labeling of the pole figures of Fig 2. The correct plane for Fig 2b and 2c is the plane in parenthesis above the figure numbers and not that in the figure subtitle. J. T. NORTON—Also, I would like to mention another method of obtaining the data for pole figures which would be particularly applicable to this problem. It is a method which has been published only

Jan 1, 1950