Search Documents

By Gerald Edmunds, C. W. Siller, E. A. Anderson

In the pressurc die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger arid a complcte shutdown of the equipment. All of the zinc alloys used for pressure dir-rnsting today contain approximately 4 per cent of aLUminum, which is more than suffieient to make plunger opcration feasible. The clearancc bet,ween the plunger and its bushing is an important matter. As the space bccomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still uscd in some machines. However, the rate at which the plunger c1earance. increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new matcrinls more: capable of retaining the desired clearance during long periods of use. Today marly die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger. operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the pluriger will operatc for a long time, of course.. The authors have developed a laboratory apparat,us in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clearance area.

Jan 1, 1940

By L. R. Jackson

THE idea presented in this paper is that the capacity of a metal for plastic flow before rupture is dependent on the type of stress system applied-that is, the absolute magnitude of the stresses are unimportant provided that they are large enough to produce continued flow; the important factor is the "type" of stress system. A term called the "triaxial stress ratio" is defined in such a way that this ratio can be used to characterize the "type" of system. The paper is divided into three sections. The first section discusses means of representing the effect of complex stresses on plastic flow and defines "triaxial stress ratio"; the second section discusses various methods of' obtaining complex stress distribution. The third section gives some experimental results showing the effect of types of complex stress on the capacity of various metals for flow. An appendix discusses some details on methods of obtaining complex stresses. I. REPRESENTATION OF COMPLEX STRESS SYSTEMS AND THEIR EFFECT ON PLASTIC FLOW Representation of Stresses It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses [S1 S2 5 S3]. This system can be resolved into a new system consisting of the three components [ ] and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation [ ] Sm is given by Eq. I and S1 is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. [ ] Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1944

By Morris A. Steinberg

Because of the broad scope of my topic I will discuss my subject from the point of view of a present status of the metallic materials that are used in structures and will dwell primarily on those structures related to high- performance aerospace systems. Thus, I can best portray the status of these structural materials as related to existing transportation systems, delineating some of the highlights of alloy development, fabrication, and properties obtained. I shall point out what are, in my opinion, the needed solutions to pressing unsolved metallurgical problems connected with certain selected metals: aluminum alloys, beryllium, titanium, steels, superalloys, refractory metals and some metal-matrix composites. Aluminum Alloys For a number of years a series of strong aluminum alloys used for airframes has had an important bearing on the development of minimum- weight, highly efficient structures. Among these alloys are such familiar ones as 2024-T3, 2014-T6, 7075-T6, 7079-T6 and 7178-T6. A review of the development and use of strong aluminum alloys in aircraft structures indicates that before about 25 years ago there was very little application of products other than forgings in the high-strength tempers produced by precipitation heat treating to T6- or T8-type tempers. 1 As stated by Dix in 1944, "There has been a gradual evolution in engineering viewpoint regarding the mechanical characteristics which are required in a structural material suitable for aircraft. Formerly, emphasis was placed on a generous spread between yield and tensile strengths, on elongation, on impact strength and on resistance to corrosion. Aircraft structural engineers still differ widely as to the importance which they attach to these proper tie.” 2 It is fair to say that this evolution is still taking place, that the problem is much the same in 1970 as in 1944 - except that strength levels have advanced some - and the question remains as to how far we can go in that direction. In the meantime, a new group of alloys has received acceptance and widespread use. The first alloy of this group, 7075-T6, was formally introduced by Dix's 1944 paper. The drastic changes that have taken place in the size and configuration of components employed in air-

Jan 1, 1971

By Valentin Garfias

ALTHOUGH Mexico still ranks second in importance as produce for petroleum, the output in 1924 was 7 ½ per cent. less than in 1923 and 30 per cent. less than the peak production of 1921. The decrease may be partly accounted for by labor troubles and revolutionary activities early in the year, although undoubtedly the main factor was the continuous rise of the salt-water level in the South Fields, causing a decline of 24,000,000 bbl. in the production of light oil. Since the middle of 1923, the production of heavy crude has been greater than that of the lighter grade and, in 1924, the output of heavy crude was 2 ½ times that-of the light oil. DEVELOPMENT Drilling operations in the Mexican fields were probably more active in 1924 than in any other year, the greatest activity taking place in the Cacalilao and neighboring fields; toward the end of the year there was an added number of wells drilling in wildcat areas. The number of wells drilled in proved territory was almost twice that of the previous year, the increase taking place in the heavy-oil fields north of Panuco, as only 78 of the 710 wells completed were drilled in the Southern Fields. The percentage of successful completions decreased from 45 per cent., during 1923, to about 38 per cent., during 1924; there was also a noticeable decrease in the average flush production of the new wells. It is interesting to note that notwithstanding the increased drilling activity, the total production declined over 10,000,000 barrels. In the heavy-oil district, 632 wells were completed but only 231, or 36 ½ per cent., were commercially productive. The develop-ment in the Cacalilao area reached its peak in April and May, or about the time the first serious salt-water encroachments took place. Development in the old Panuco and Topila fields was more active than during the previous year, although the salt-water level continued to rise, the high price of crude making such development advisable especially for companies having to protect large-investments.

Jan 3, 1925

By W. A. Anderson

IN the pressure die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger and a complete shutdown of the equipment. All of the zinc alloys used for pressure die-casting today contain approximately 4 per cent of aluminum, which is more than sufficient to make plunger operation feasible. The clearance between the plunger and its bushing is an important matter. As the space becomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still used in some machines. However, the rate at which the plunger clearance increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new materials more capable of retaining the desired clearance during long periods of use. Today many die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the plunger will operate for a long time, of course. The authors have developed a laboratory apparatus in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clear-ance area.

Jan 1, 1939

By Guido Bassi

IT is known'" that secondary recrystallization occurs in copper sheet with at least 90 pct reduction after annealing at high temperatures, 700" to 1000°C. Turkalo and Turnbull4 have found recently that secondary recrystallization might occur even after annealing at such low temperatures as 500°C for a high purity, coarse-grained copper sheet. It will be shown in the following that in an electrolytic tough pitch copper wire, with a high degree of deformation, secondary recrystallization might occur at even lower temperatures. A hot-rolled rod of 9.5 mm diam (temperature at which rolling commenced was 850°C) was drawn in continuous drawing machines to 0.4 mm, corresponding to a cross-section reduction of 99.8 pct. The texture in the center of the wire (the sample for X-ray analysis was etched to 0.15 mm diam) is a mixture of the [111] and the [loo] direction, as can be seen from Fig. 1. This is in accordance with the result of Schmid and Wassermann.' After a few minutes annealing of the wire at 200 °C, there is a noticeable recrystallization of the structure with a preferred orientation in the [l00] direction at the expense of the [Ill] deformation texture, as Figs. 2 and 3 show. Farnham and OINeill" reported a similar result. The final recrystallized structure shows mainly the [loo] orientation. There is however a small amount of [111] and random orientations. If the wire is annealed at 400°C, the recrystallized structure first shows a [loo] texture, Fig. 4, but as the annealing time is increased the fine-grained structure transforms into coarse grains, Fig. 5, giving a new preferred orientation, Fig. 6. The calculations show this to correspond to the [I121 direction. Even if the annealing that gives the primary recrystallization is carried out for six weeks at 20O°C, the same secondary recrystallization texture is obtained if the annealing is continued at 400°C. Schmid and Wassermann7 found the [I121 texture, but only after annealing at 1000°C or higher. The appearance of a secondary recrystallized

Jan 1, 1952

By H. B. Bell, P. C. Lidster

A study has been made of the use of ThO2-Y2O3 solid electrolytes to determine activity of chromium in Fe-Cr and Ni-Cr alloys in the temperature range 1300° to 1700°K. This method has been shown to give results which agree with the best vapor pressure measurements. SEVERAL investigations1"5 have been made of chromium activities in Fe-Cr alloys. Most of these have been made by vapor pressure measurements using knudsen cell techniques while one has been made using gas equilibration with H2/H2O gas mixtures. In the present investigation electromotive force measurements have been made on this system using a thoria yttria solid electrolyte. This system was -chosen to establish the technique of measurement at low oxygen potentials, before extending it to Fe-Ni-Cr alloys. The cell used was Pt Cr • Cr2O3 ilThO2 • Y2O3 llalloy • Cr2O3 IPt Since the oxygen pressure of the chromium-chromic oxide mixture lay in the range 10"19 to 1027 atm in the temperature range investigated, thoria yttria electrolytes were used. It was soon found during the investigation that considerable care was required to prepare satisfactory electrolytes and a study was made to find the best method of preparing pellets of TI1O2-Y2O3 solid solution of as near theoretical density as possible. Various compositions in the range 2 to 15 mole pct Y2O3 were studied but the experimental measurements were made with electrolytes containing 4 to 5 pct Y2O3. The method of preparation finally adopted was to use thorium oxalate and yttria as raw materials. The thorium oxalate was decomposed at 900°C for 6 hr to give a reactive powder. This powder was then mixed with the appropriate amount of yttria and ground in an agate mortar for about 4 hr. The powder was moistened with absolute alcohol as a lubricant and pressed in a metal die at a pressure of 7 tons per sq in. The pellets were then heated at 1100°C for 24 hr followed by 24 hr at 1250°C. After this firing cycle the material was reground and repelleted and again fired at 1100° and 1250°C followed by heating for 7 days at 1600°C. It was found in later experiments that a further firing of 4 hr at 2000°C improved the density further and gave pellets of only 2 pct porosity. After firing, the pellets were polished on emery paper and finally with the 2 µ diamond paste. The polishing was followed by a final firing of 24 hr at 1500°C. Investigation showed that this final treatment minimized reaction between the electrolytes and chromium oxide. It was believed that this was because of a lowering of the surface energy of the electrolyte surface. Two types of investigation were carried out to check that the pellets were satisfactory oxygen ion elec-

Jan 1, 1970

By E. Baker, David Donoghue

Legal and legislative matters constituted the outstanding features of proration in Texas in 1932. From East Texas emanated most of the political, legal, technical and industrial activity. Conroe and Thompson developed into fields of major importance. Proration orders were issued by the Railroad Commission on many of the producing fields of the Gulf Coast and West Texas not covered in previous years. In Yates, Penn Pool, Winkler, Van, the Panhandle, North Texas and West Central Texas there were 110 changes of importance, except in allowables. New proration schemes were introduced in East Texas, Conroe, Thompson, Saranosa, Government Wells, Tuleta and Howard-Glasscock. Little progress was made in administration or technical development. Legal and Legislative Matters Proration first began in Texas in 1927 as a voluntary attempt to divide the market outlet of a field on an equitable basis. The statutes then in existence were considered somewhat archaic and the Railroad Commission's authority was limited. Subsequent efforts to strengthen the laws were not wholly successful. The 1929 Conservation Act made no mention of market demand but declared that the term "waste" did not mean " economic waste." With the passage of the Pipc Line Act of 1930, providing for ratable purchasing, it was the opinion of many lawyere that a legal means of proration had been found. The 1931 law had ths same provision as that of 1929 with respect to economic waste but specifically prohibited limiting of production to market demand. The law passed Nov. 12, 1932, omitted reference to economic waste and specifically provided for limitation of production to reasonable market demand. Vigorous attacks were being made in State and Federal Courts on the constitutionality of the laws and the validity of the Commission's orders. In Peoples Petroleum Producers, Inc. et al. vs. Lon A. Smith et al., which had been heard before a three-judge U. S. District Court in Houston on May 28, 1932 and again on Sept. 19, the Court's decision for plaintiffs, released Oct. 2, influenced in a large measure the calling of the Legislature and the passage of the Market Demand Law on Nov. 12.

Jan 1, 1933

By R. A. Liddle

Intermitt'en'I'ly during the past 10 years showings of oil and gas in tests drilled in the eastern part of Texas have stimulated the search for production. Tests on the flanks of the long-known salt domes, principally Keechi and Butler, have found oil in small quantity in the Woodbine formation of the basal part of the Upper Cretacrous. In the central part of Cherokee County, Colliton et all in 1926, in their Clapp No. 2 found a good showing of 37" B6. oil at about 3500 ft. Several wells were drilled in 1926 and 1927 as a result of this showing. On Jan. 22, 1927, Humble Oil & Refining Co. wildcatting on Carey Lake salt dome, obtained commercial production in its Clark No. 1. This inaugurated intensive exploration both for salt domes and for other types of structure. As a result several new domes and a few promising structures of other types have been discovered. Development in East Texas durinG 1927 Carey Lake Dome Location.—On the Neches River in Anderson and Cherokree counties, 10 miles west of Jacksonville, Cherokec (lounty. (Fig. 1.) date of Discovery.—During 1925 geologisls of the Humble Oil & Refining Co. working in the Neches River valley discovered slight surface fracturexs, cratic dips, and slickensided clays and sands in green-sands of the Mount Selman formation north of Carey Lake. A number of core tests were drilled by the Humble Oil & Refining C'o. during 1925 and 1926, some more than 1500 ft. deep, to check their surface obsuvations of faulting, and the possibilities of a salt dome. On May 16, 1927, solid rock salt was reached at 2142ft. in the first deep test on the prospect. Surfacc Indications.—Surface indications of the Carey Lake dome, though not as evident as manifestations at the previously known domes of Palestine, Keechi, Butler, Grand Saline, Steen and Brooks, are more noticeable than on any of the domes discovered in 1927. F. E. Poulsen, of the Pure Oil Co., who examined the area before the deep tests were drilled, noted the alignment of erratic surface dips which suggested faulting, especially in conjunction with slickensiding, and the local deflec-

Jan 1, 1928

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915

By Claudio Barsotti, Leonard C. Kitchener

INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits

Jan 1, 1981

By A. U. Seybolt, R. A. Oriani

The pressure and composition of the solid solution of nitrogen in chromium has been investigated as a function of temperature. The partial molal heat of solution, the activity of nitrogen in solid solution, and the partial molal free energy have been computed. The enthalpy of three reactions is summarized: N + 2Cr(3) = Cr2N(4), H° = —28,500 cal per mol 1/2N2(p) + 2Cr(8) = Cr2N(3)1 ?HO = —23,500 cal per mol 1/2N2(p) = N, ?H° = 5,000 cal per mol. WORKERS who have investigated the problem of the preparation of ductile chromium have been concerned with the effects of minor amounts of impurities upon this refractory metal. In particular, gaseous impurities such as oxygen and nitrogen have been suspected of causing trouble because of many known cases where brittleness in transition elements has been definitely traced to these elements. In order to evaluate the possible effects of the nitrogen impurity in chromium, it appeared desirable to learn something of the dependence of the nitrogen solubility upon temperature and pressure. Previous Work Maier3 in 1942 in his treatise on sponge chromium reviewed the thermodynamics of the chromium nitrides Cr2N and CrN, both of which are well-estab- lished compounds, but which apparently have not been studied in much detail. Maier presented some free energy-temperature expressions for the reactions 2 Cr,N = 4 Cr + N2 [1] and 4 CrN = 2Cr2N + N2 PI based mainly on the work of Satoh2 and Sano." Pearson and Ende3 in 1953 briefly reviewed the thermodynamics of Cr-N using the same data available to Maier, and also derived a free energy-temperature expression for reaction 1. Of the two nitrides mentioned previously, the present investigation was only concerned with Cr,N, since this nitride is in equilibrium with the metal phase, at least over most of the temperature range, Blix4 in 1929 established the structure of Cr2N (close-packed-hexagonal) by X-ray diffraction methods, and indicated that its homogeneity limits extend from 11.2 pet to 15.1 wt pet N. At a temperature of 1200°C, 38 mm Hg from the Maier expression and 43 mm Hg from the Pearson

Jan 1, 1957

By A. Brown

RAPIDLY rising world demand for mineral products has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations. In recent years the Mines Branch of the Department of Mines and Technical Surveys in Canada has conducted such an investigation. This report of the work is primarily concerned with stress problems in some Canadian coal mines and, in particular, with mine bumps. Mines Branch investigations of this and related problems are carried out by a small team of mining engineers and physicists who, with assistance from geologists, pool their special skills in an integrated program. These Canadian investigations combine a field and laboratory approach. Since data obtained under contrasting mining conditions allow useful comparisons of ground behavior under stress, this article will present data gathered under a wide range of Canadian coal mining conditions. Two contrasting longwalls in eastern Canada will be discussed and two dissimilar pillar extraction operations in western Canada. Locale of Observations In eastern Canada observations are being made in the collieries at Springhill, Nova Scotia. The district's No. 2 mine, which has a history of bump occurrences dating back to 1917, is currently being worked at a depth of 4200 ft. The mining method is longwall retreating along the strike and the practice is to retreat three walls in line, each about 350 ft long. There is no machine cutting or shooting—the coal is hand-picked and hand-loaded onto face conveyors. There are three rows of hardwood chock block supports parallel to the coal face. These supports are built during the two daily coal loading shifts, and the rear line is withdrawn during the midnight shift. The goaves are partially packed by stone midwalls 12 ft wide which are built forward daily in step with the face advance. The seam dips at 15° and averages 9 ft of strong, well cleated bituminous coal enclosed in competent beds of shales, sandy shales, and sandstones of Carboniferous age. The bumps rarely disturb the retreating longwall faces but manifest themselves as violent upthrusts of pavement in the levels leading to the walls. Observations have also been made in Springhill's No. 6 mine, which operated in a 5-ft seam of coal at a depth of about 2500 ft. Although No. 6 mine was

Jan 1, 1959

By C. A. Bruch, J. F. Duffey

On the basis of metallographic and cooling-rate studies of 15 U-Zr alloys, a new version of the 6 phase region of the U-Zr phase diagram is proposed. IN several published diagrams of U-Zr alloy system:' there is good agreement that at elevated temperatures complete solid solubility exists between y uranium and ß zirconium. Similarly, there is reasonably good agreement concerning the uranium-rich and zirconium-rich ends of the diagram. However, there is no agreement concerning the nature of the diagram at intermediate compositions and at temperatures below about 650°C. The early work of Saller et al.8 hows an intermediate phase, 6. In a later diagram by Saller and Rough' shown in Fig. 1, the d phase field is drawn with dotted lines, indicating doubt that this phase exists. The diagram of Summers-Smith2 does not show the d phase. More recently Holden and Seymour' have shown that in the composition range 40 to 60 wt pet Zr, the high-temperature ? phase, which is body-cen-tered-cubic, transforms to an ordered structure, 8. They found that the order-disorder transformation occurs between 595° and 610°C, and presented a diagram based on the study of four different alloy compositions. Most recently Saller et a1.5 presented a new diagram which differs with respect to the composition limits of the 8 field from the others proposed by these authors. The purpose of the present investigation was to determine the boundaries of the d phase field. Experimental Procedures and Results Alloys—Buttons, weighing 80 g of 15 different alloy compositions were prepared by arc melting Mal-linckrodt uranium and iodide-process zirconium in a water-cooled crucible. A controlled atmosphere of argon and helium was maintained in the furnace. Prior to making each button, a sacrificial button of zirconium was melted to increase the purity of the furnace atmosphere. Each alloy was then melted six times to improve its homogeneity. Subsequently the alloy buttons were jacketed in copper and hot rolled to slabs at 775°C. From these slabs, specimens were machined for chemical, thermal, and metallographic analyses, Table I gives both the estimated chemical composition of the alloys, and the values which were obtained by analysis. The oxygen contents varied from 0.013 to 0.032 pet, nitrogen from 0.0014 to 0.014 pet, and carbon from 0.0013 to 0.011 pet. The purity of the alloys ranged from 99.947 to 99.975 pet. Thermal Analysis—The specimens for thermal analysis were blocks 11/4 x 1/4 x % in. The bead of a calibrated thermocouple was placed between two of these blocks and molybdenum wire was wrapped around the assembly. Each assembly was sealed in a quartz capsule having an argon atmosphere. The capsule was placed inside a refractory crucible which was heated in a furnace. Using a method described by Smith,' the emf of a differential thermocouple, with junctions inside and outside of the refractory crucible, was used to activate the

Jan 1, 1959

By C. E. SWANN

NOT long ago an engineering study was made to determine if the time had arrived to lower the head of standing water in abandoned Rock Springs mines Nos. I and 3 of The Union Pacific Coal Co. so that this water would not become a menace to the future operations of adjacent mines or mines developed on seams lower in the coal measures. This survey resulted - in a decision to unwater the No. 1 mine workings and, incidentally, the old No. 3 mine workings by drilling a large-diameter hole from the surface to an opening in No. 1 mine at the sump below 21 entry, provided it was found practical to operate a large-capacity, vertical, deep-well pump under the existing conditions. This would relieve the static bead of 200 ft. of water at the fault that separates Rock Springs mines Nos. 1 and 4, which is the

Jan 1, 1935

By AIME AIME

SHORTLY after he started his professional career, the subject of this sketch acquired the sobriquet "Moose" Allen. At the time he was engaged in geological exploration it1 the Canadian wilds. The nickname was given .him because of the wide, straight trail that he broke with unusual speed when going through the bush. Like a moose he was strong, energetic, and determined. To a considerable degree, Rolland Craten Allen today displays the same characteristics in larger affairs-business, civic, and professional. It is his habit to study a problem thoroughly, to decide u11on the best course of action, and then to pursue that course with vigor and

Jan 1, 1936

Jan 1, 1932

By David Mandolesi

An examination has been made of the structures of strand cast blooms and the rails rolled from them; this paper details the characteristics of these typical structures. Results of mechanical testing data show that this product compares with rails processed from conventional ingot steel. Improvement in processing yields and surface quality standards are also briefly discussed.

Jan 1, 1972

By G. W. Jr. Jarman

THE purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electro-static separators and air flotation or air tables.

Jan 1, 1938

By Arthur V. Abbott

TO rightly use materials, two kinds of knowledge are essential: first, the actual strength of the substance; and secondly, the forces to which, in the structure, it may be subjected. Nearly all of the data which we have at the present time have been obtained from the experiments made on the materials used in Europe, and by foreign investigators. The materials commonly used in this country, es-

Jan 1, 1884