Search Documents

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation. A series of temporary and permanent water pumping stations is planned. Generally, the temporary stations are located above major aquifers to facilitate water removal while sinking through the aquifer and the permanent stations constitute what, in the final mode, will be the mine dewatering system. In addition, Phillips Uranium Corporation has In- stalled and is maintaining a system of depressurization wells that temporarily pump the major aquifers and considerably reduce the water inflows during shaft construction. The major aquifers are also chemically grouted prior to sinking. Site work for the project was initiated in the fall of 1976. Full scale shaft sinking commenced in November of 1977 on the 4.88 m (16 ft) diameter ventilation shaft and on the 5.49 m (18 ft) production shaft by another contractor. Harrison Western Corporation began work on the project on November 4, 1979 wlth the production shaft at a depth of 633 m (2,076 ft) and the ventilation shaft at a depth of 474 m (1,554 ft). This paper will address only the portion of shaft sinking completed by Harrison Western. Geology and Hydrology The Nose Rock Project is located on the Chaco Slope in the southern extreme of the San Juan Basin in northwest New Mexico. The southern San Juan Basin is generally bound by the Defiance Uplift to the west, the Zuni Uplift to the south and the Nacimiento Uplift to the east. The Grants Mineral Belt occupies most of the southern portion of the San Juan Basin and this project is located on the northern extreme of the Grants Mineral Belt. The San Juan Basin is comprised of sedimentary rock of continental, marginal-marine and marine origin, that dip northward from the Zuni Uplift and Chaco Slope into the interior of the San Juan Basin. (See Figure 2) Major Formations The major geologic formations to be penetrated range from mudstone and shales to siltstones and sandstones. The sandstones are highly productive aquifers which, under static conditions, would flow artesian. Water temperatures in the aquifers are high and therefore are a force to be dealt with. Temperatures range from 18ºC (65OF) in the upper aquifers to 48ºC (118º'F) in the lower. The mudstones are generally bentonitlc. (See Figure 2) GALLUP SANDSTONE: The Gallup Sandstone is the first major regressive wedge in the San Juan Basin of the Cretaceous era and at this project is about 35 m (115 ft) thick. It is medium grained and prior to depressurization carried a hydrostatic water pressure of over 72.5 kg per cm2 (1,031 psi) which 1s artesian. Compressive strength ranges from 334.7 kg per cm2 (4,760 psi) to 421.8 kg per cm2 (6,000 psi). Water temperature is approximately 30°C (86°F).

Jan 1, 1982

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By Roswell Johnson

To know the rate of decline of oil wells is very important, yet ordinarily we are prevented from getting this rate because the oil from several wells is put into one or a few tanks as soon as the wells have been connected to the power. The object of doing this is economy of tanks, pipes, labor and accounting. FIG. 1. But we are making a great sacrifice for this small economy. The advantages of the individual records are that we would know better: 1. When the well has ceased to be profitable. 2. When a well has gotten into bad condition. 3. The real record of the yield per acre and the rate of decline of the wells. The lease total is too mixed as to age of the wells for existing records to have much significance. To obtain such individual well records and more accurate logs are the great desiderata of satisfactory management of oil properties. 4. Which wells show the slowest decline-information which is valuable in locating new wells or purchasing adjoining leases.

Jan 6, 1917

By W. R. Ingalls

In choosing the unusual title given to this paper, in which the term "cyclic " might be substituted for "intermittent," my idea has been simply in respect of precision. We might say old method vs. new method, but that antithesis implies something of substitution that has not occurred and perhaps is not in sight. We may say horizontal retorts vs. vertical, but none of the older retorts are truly horizontal, and there are three different types of vertical retorts. Other complexities might be suggested. There is, however, a broad distinction between distilling that is accomplished in a periodic cycle, generally daily; and distilling that is accomplished continuously, irrespective of whether it be done in the vertical retorts of the New Jersey process or in the retorts of the Trollhät-tan process. In offering a summary of the present state of the art with the intermittent process, I shall not have any idea of exemplifying it through descriptions of any single plants, but shall rather divide among the main steps of the process and outline what is best developed among them. In pursuing this thought, it will manifestly be impossible to make a composition that will exemplify the acme of good practice, for the latter will always be a function of the cost of labor, fuel, etc., which are widely variable. As of 1929, in respect of labor we might generalize the average plant wage in the Pittsburgh-Wheeling district of the United States at $5 per day; in Oklahoma at $3; in Great Britain at $3; in Germany at $1.75-$2; in Belgium and France at $1. With high labor costs the metallurgist will naturally use means of the nature of mechanization that with low labor would be uneconomical when capital charges are taken into account. Nor may we from records of performance safely make positive deductions in respect of the efficiency of different types of furnaces unless they have been tested comparatively under identical conditions in the same works. We shall find gas-fired regenerative furnaces showing coal consumption from 1.2 tons down to 0.7 per ton of roasted ore, which may be ascribable to difference in the thermal value of the coal that is used or to differences in proportions of the parts of the furnace, which is something quite distinct from the principle of the furnace. Thus, we have

Jan 1, 1937

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By Charles H. Snow

In vol. xxxviii. (1889) of the American Journal of Science, under the heading " Pseudomorphs of Native Copper after Azurite from Grant County, New Mexico," Mr. W. S. Yeates describes a most interesting mineral form. His account is, that a material having the appearance of native copper, but brittle and much lighter than native copper (its specific gravity being but 4.15), was submitted to him by the United States National Museum for examination. The substance was reported to him as occurring in masses, varying in weight from one ounce to seventy pounds, and composed of tabular crystals, variously grouped. The specimens, when submitted, ex hibited on the outride a covering of clay; and they were subse quently found to consist of particles of the same clay, intimately mixed with others of native copper, producing the aspect, without the weight, of pure copper. The forms of the azurite crystals, found at Bisbee, Arizona, having been suggested by the specimens, actual goniometer-measurements were made; and the two crystallizations were thus proved to be identical. To these statements I may be permitted to add some further in formation, derived from personal examination, and illustrated with a suite of characteristic specimens collected by myself (Fig. 2).* Grant County, New Mexico, in which these specimens were found, is a region noted for variety of mineral species. The sixth edition of Dana's Mineralogy mentions many of the silver, copper, and lead minerals, and also turquois, aragonite, wulfenite, barite, fluorite, vanadinite, etc. I have noticed also green and red garnet, molybdenite, native alum, smithsonite, bornite, etc., some of which presented peculiar modes of occurrence. The green garnet, for instance, was in masses formed of separate crystals, each of pea-size and not unlike that vegetable in tint and smooth opaqueness. The crystallization was

Jan 1, 1893

By Herbert Hoover

THE Federation of Engineering Societies has been created for the sole purpose of public service. This initial meeting surely warrants some discussion of a few of the problems to which this organization, for expression of the --. engineering mind, can quite well give consideration. Some of the greatest of the problems before the country and, in fact, before the world, are those growing out of our industrial development. The enormous industrial expansion of the last fifty' years has lifted the standard of living and comfort beyond any dream of our forefathers. Our economic system under which it has been accomplished has given stimulation to invention, to enterprise, to individual improvement of the highest order, yet it presents a series of human and social difficulties for the solution of which we are groping. The congestion of population is producing subnormal conditions of life. The vast repetitive operations are dulling the human mind. The intermittency bf employment due to the bad coordination of industry, the great waves of unemployment in the ebb and flow of economic tides, produce infinite wastes and great suffering. Our business enterprises have become so large and complex that the old personal relationship between employer and worker has to a great extent disappeared. The aggregation of great wealth, with its power of economic domination, presents social, economic ills which we are constantly struggling to remedy.

Jan 1, 1920

By BLAllEY STEVENS

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. TEH object of this paper is to show how igneous intrusion is governed by definite mechanical laws. A distinction is made between dikes and fissures, and the various characteristics of intrusions are explained on an exact scientific basis. The modification of rock-stresses by intrusion is then considered and extensive isostress regions are recognized. Finally, a complete classification of intrusions is constructed covering all pos-sible cases. The generalizations of observed data, taken from Geikie's Textbook of Geology, conform to the laws of intrusion herein stated, and the deductions based upon these laws. No authority, however, is quoted for the type which I have named a corrugated intrusion. Its existence is a necessary deduction from the laws of intrusion, and even the entire absence of examples in technical publications cannot disprove its reality. In all probability, corrugated fissures would have remained undiscovered, but for the working of mineral veins. As intrusions of tabular form are seldom worked for commercial purposes, it has been left for theory to anticipate the discovery of corrugated dikes. In the light of these laws of intrusion and the corresponding laws of fissures,1 there seems to be a remarkable uniformity of stress-distribution in rocks at moderate depths. This renders .possible the mathematical calculation which should help us to approximate exact science in this and kindred branches of applied geology.

Jan 1, 1911

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

THE crystallographic mechanism for the austenite-to-martensite transformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite-and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite undergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.-Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about -70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of I mm. or more. Four martensite cystals from four different ingots were prepared in this manner; the largest crystal of this group is illustrated in Fig. I. Back-reflection Lane patterns were obtained from martensite [ ] crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution (±0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to {112} and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Donald C. Moore

INTRODUCTION Published laboratory procedures used by the major crusher manufacturers for estimating crusher size are based upon techniques developed in the mid 1940's. Specifically, the two largest U.S. crusher manufacturers are using the Bond impact procedure. Although the procedure is still in use, there is little confidence in the results. Unless the laboratory results fall within a preconceived range, personal experience is used for selecting the number of crushers and connected horsepower (Coleman, 1978). There have been numerous theoretical studies of the communition of particles. However, no procedure has been widely acclaimed for predicting crusher power requirements. Experimental studies have included breakage by slow compression, slow speed impact and high speed impact. Theoretical results have increased our knowledge of the comminution process, but the procedures have not been capable of analyzing the complex mechanism of industrial crushing machines. The purpose of this chapter is to review the empirical crushing procedures that have been used, including advantages and disadvantages. A new procedure which has been in development at Allis-Chalmers Corp. from 1977 to 1982 is detailed. Actual results of the new procedure on a concentrator feasibility study are included. EXPERIMENTAL GOALS The goals of a laboratory crushability procedure are accurate predictions of: (1) Rock crushability, measured as energy per unit mass. (2) Crusher product size analysis. A procedure capable of predicting these parameters should be inexpensive and require a minimum amount of sample. CRUSHABILITY TESTS Bond Impact Procedure F. C. Bond (1946) detailed the development of the pendulum impact device that is still used by the leading crusher manufacturers (Bond; Rexnord, 1976). The device (Fig. 1) is comprised of two bicycle wheels with 13.6 kg steel hammers tangentially attached to the rims. The hammer faces are 50 mm apart at rest. On opposite ends of the hammers lifting

Jan 1, 1982

By AIME AIME

THE petroleum economics session," held on Wednesday morning, Feb. 20, 1929, presided over by Campbell Osborn, chairman, proved to be of un- usual interest and resulted in serious and constructive discussion of the papers presented. The first paper on the program, "Gasoline Economics and Refinery Operation," was by H. J. Struth, petroleum economist of the Gulf Publishing Co., Houston, Tex. While this paper was intended to cover the re- finery situation, it also presented the author's reasons for believing that the oil producer should give cognizance to gasoline demand as a most reliable barometer by which to parallel the production of crude petroleum. The discussion which followed brought out some interesting points in connection with the immediate outlook for the industry as a whole during the present year. Some advanced the opinion that, regardless of the out- come of proration efforts, the refiner is in a position to conduct his operations on a reasonably profitable basis, provided that he exercises control over them. This would mean running less crude and resorting to wider utilization of cracking to produce the gasoline demand. Thus, if the refiner uses diligent care in scheduling his still runs, the producer will be obliged to carry over a large stock of crude this year, unless he is able to keep production below the limits prescribed by the demand for gasoline.

Jan 1, 1929

By B. E. Cornish

Most technical and statistical data published on pyrophyllite relating to production figures, uses, markets and sales, have in the past traditionally linked the mineral with talc and soapstone. This is due to several common superficial physical properties resulting in substitute uses and applications. However, these minerals are not similar in chemical composition and do not generally occur in a similar geological environment. Pyrophyllite now stands on its own in the marketplace-particularly in ceramic applications-due to the combination of excellent heat shock and creep resistance properties of the mineral. The increase in pyrophyllite use in the field of ceramics indicates the continuing realization of these marked unique properties. Several new fields of ceramic applications, previously the preserve of high-alumina materials, have been developed on the intrinsic properties of pyrophyllite. Pyrophyllite is an aluminum silicate with the molecular formula of AI2O34SiO2H2O. It would be more appropriate to group pyrophyllite with such materials as kyanite, diaspore, andalusite, and certain high-alumina clays in relation to its general applications (Stuckey, 1928). These materials all have good beat shock resistance properties at high temperatures and are widely used for the manufacture of refractories. For those reasons they are interchangeable in some applications. Pyrophyllite also has many uses in nonceramic applications, the most important to date being as a substitute for talc in fillers. The major pyrophyllite mining operations are located in the US, Japan, Korea, Canada, and Australia, where the mineral is widely used as a raw material for general ceramic, mineral filler, and dilutant applications. Commercial Applications Pyrophyllite was first used in the last century for lining stoves and fireplaces, and also in the carving and polishing of ornamental objects. The rise in industrial demand for new products and applications resulted in the introduction of pyrophyllite as an alternative, mainly for talc and soapstone. Industrial filler applications followed for paint, paper, cosmetics, rubber, pesticides, crayons and pencils, and bleaching soap. The first use of pyrophyllite in ceramic applications was prior to World War II, in the manufacture of ceramic cladding tiles in the US. This was followed by the production of kiln furniture refractories and whiteware when pyrophyllite was offered by suppliers in North Carolina as an alternative to some local clays. The largest tonnages of pyrophyllite used today are in refractory linings in steel ladles in Japan, as seen in Table 1. The consumption of pyrophyllite in Japan is second only to clay and chamotte among refractory raw materials used. Recently this technology has been adopted in Australia. Japanese and Australian practice has resulted in appreciable technical and economic benefits, particularly when pyrophyllite is used in combination with zircon. The potential growth for this application is substantial if US and European steelmakers follow. Investigation and research into the properties of pyrophyllite determined the following main advantages of pyrophyllite-based ceramics: high corrosion resistance for molten iron, steel, and slags; good heat shock resistance; good indices of deformation under load and hot creep resistance (refractories); and increase in mechanical strength of whiteware products promoted by a better distribution of mullite in finished products (also obtained at lower firing temperatures than normally required in production of triaxial ceramics). White cement

Jan 1, 1983

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory state of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which are useful for predicting machine performance and give, acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary in commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed' in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted. In its first form, as stated by P. R. Rittinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include .the concept of surface energy; in this form it was precisely stated by A. M. Gaudin2 as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended. According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps, 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported' that support the theory in its first form by indicating that the new surface produced in. different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work" done on. the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading since it does not follow the regular breakage pattern of most materials but is relatively harder to grind at the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory' is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr/log 2.5 The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in. reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-1.5 If a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The'evaluation in terms of kw-hr per net ton of 200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of -200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned, with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1952

By R. A., Pallanch

SO many variations of lead-zinc ores occur in nature that it is impossible to state any rules that will apply to the concentration of ores of this type. Some have lead and zinc in approximately equal amounts; others may have pre- dominant amounts of one or the other metal. There are gradations from all sulfide to completely oxidized minerals. Some such ores carry little pyrite, others contain much more pyrite than they do lead and zinc combined. The behavior of ores in flotation is largely a function of their lead-zinc ratios. their content of pyrite or pyrhotite, the nature of existing soluble salt conditions, the character of the gangue constituents: and the speed with which the minerals float. For the purposes of this paper only those lead-zinc ores handled commonly in present-day flotation practice will be considered. These are practically all-sulfide ores with relatively minor degrees of sulphatization or oxidation.

Jan 1, 1936

By GILBERT E. SEIL

GREAT advances in the preparation of ores for reduction to ferro-alloys have been made, although standard methods of reduction have been continued at most plants. Efficiencies, yields per furnace, and energy requirements per ton are generally better than previously attained. The advantages of sizing and conditioning of ore, fluxing stone, and coke have been realized. Conditioning varies from drying the furnace burden to chemical rearrangements to facilitate reduction reactions and sometimes to furnish some of the energy required for the reaction before the burden reaches the furnace. During the war period it is impossible to discuss in detail many of the advances made. They are subjects for postwar papers. However, the new procedures mentioned in the following paragraphs are indicative of the work already done and in progress.

Jan 1, 1944

By R. S. Rickard

Chemical processing of ores has gained new im¬petus in recent years. The reasons are many. They range from the need to process ores that are difficult to beneficiate to the avoidance of pollution. Although many think of chemical processing as a hydrometallurgical operation there are other techniques. An example is chlorination. Chlorination, although examined and discarded by many investigators, is again being considered as a means of extracting uranium1, treatment of silver-lead ores2, and the recovery of base metals from pyrite cinder and ores3. Segregation roasting of copper and nickel ores, a process similar to chlorination, is another chemical treatment being revived.

Jan 1, 1970