Search Documents

By A. S. Nowick, E. S. Machlin

ONE of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.1 During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time required for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error.2~3 This method of showing stress-rupture data has been adopted by many investigators and the KACA.4 By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, 100, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time for rupture on stress, temperature, com- position, and structure. In order to obtain this information, an investigation was made at the KACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given com- position and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efficiency and power output of gas turbines used in aircraft propulsion can be increased. THEORY The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 eveloped by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate- process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process.'' For example, in a chemical reaction the unit process is

Jan 1, 1947

By R. S. Archer

The proper representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem, the complete solution of which will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the Al point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A1 point is an open question, but that complete graphitization (to less than 0.10 per cent, combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440" F. It is the

Jan 1, 1922

By R. S. Archer

The proper representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem, the complete solution of which will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the Al point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A1 point is an open question, but that complete graphitization (to less than 0.10 per cent, combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440" F. It is the

Jan 1, 1922

THE Johnson award for 1926 was given to T. L. Joseph for his experimental work on blast-furnace operation. When the Bureau of Mines undertook its experimental blast-furnace investigation in 1919, a number of operators and metallurgists were doubtful as to the practicability of small-scale tests. Several pre-vious attempts, outside the Bureau, to operate small furnaces had been unsuccessful. However, pig iron was produced in three and four-ton furnaces during the first half of the nineteenth century. The operation of a small furnace did not therefore seem an impossible task. This point of view, together with a realization of the importance of problems connected with the pro-duction of pig iron, prompted the Bureau to undertake this work. Such problems as the feasibility of using charcoal briquets as a fuel, the application of oxygen enriched blast, and the use of new ores and raw ma-terials, in general, can be investigated only at consider-able cost on full sized furnaces, while with an experimental furnace they can be conducted at a com-paratively ;small, cost. The results of small-scale tests are sufficient to determine whether the problem. War-rants the expenditure required for a trial on a com-mercial scale. The accompanying photographs and chart show the various stages of the experimental furnace development. Some idea of the size and shape of furnaces which were tested can be had from the development chart. In oper-ating furnaces A to F, a series of changes were made to increase hearth temperature. Perhaps the most im-portant change was the position of the tuyeres with respect to the bottom of the hearth. The height of the tuyeres above the hearth was gradually increased and the hearth diameter decreased. It was shown by this series of furnaces that metal and slag are the chief source of heat supply to the crucible. For this reason there is a minimum rate at which these materials can be brought into the hearth of a small furnace if it is to function properly. The rate of slag "and metal fall are determined by the burden on the furnace and the rate of blowing. Due to lack of funds necessary to provide ample blowing equipment, hot blast stoves, essential mechani-cal features, and to meet operating expenses, it. was necessary to work with much smaller furnaces, such as G to K shown in the chart. The particular object of these tests was to study the extent to which reactions could be speeded up by decreasing the size of the stock. One decided change, noticed at the beginning of this series of tests, was the effect which coke size had on the production of a strongly reducing gas. Furnace G, 22 in. high, operating on coke crushed to pass 10 mesh, made a gas richer in carbon monoxide than did fur-naces A to F, operating on run-of-the-oven coke.

Jan 3, 1927

By Thomas Read

IN speaking of immaterial problems of industry I am using the word immaterial in its original sense, not consisting of matter; not in its derived sense, unimportant. There is nothing of a paradox in saying that immaterial problems are the most important in human life, for His a matter of everyday observation that much of the news in the daily papers, and most of the world's best literature and drama, deal with human conduct that has for its motive forces that are but little concerned with material things. The engineer's preoccupation with physical forces, in extending his control over them, has not blinded him to the impor-tance of forces that, for want of a better word, I call immaterial; but he has considered that dealing with the one is his job and the other is not. All the evidence of the past decade indicates that the latter are so in-extricably interwoven with the former in modern in-dustrial life that the engineer will have to concern himself with them whether he wants to or not. Some of the most important of the problems arising from the action of these forces relate to the mental hygiene of the workers in industry. Mental hygiene in industry was concisely defined, in terms of the best present knowledge, by Dr. C. Macfie Campbell, speaking last April before the executive com-mittee of the Associated Industries of Massachusetts, and as his statement can scarcely be bettered, I quote it below: "The term mental hygiene is apt to appear vague. The actual stuff with which mental hygiene deals may be briefly reviewed.

Jan 9, 1927

By J. P. Savely, D. E. Nicholas, R. D. Call

Progress in the technology of slope design over the past 15 years now permits the selection of rational slope angles if suitable data on geology, hydrology, and rock properties are available for a specified project. Although a full-scale slope design study remains the best course of action, there are situations where an extensive study is not feasible due to time or budget constraints. Two typical examples are: (a) selecting pit slope angles for a preliminary feasibility study at the exploration stage; and (b) coping with a slope failure in an operating mine. In both instances, slope angles must often be chosen on the basis of data that are currently available or can be readily obtained. All too often during exploration programs, a feasibility study is initiated shortly before the decision deadline to drop the property or proceed to purchase. If the only existing data at this point are a few cross-sections at odd angles showing ore and waste contacts or a dog-eared map of the surface geology, there may not be time to collect and organize sufficient information for the design of slope angles. On the other hand, if during the drilling program geologic cross-sections were constructed and the structural data compiled in tabular form, rational slope angles could be computed within the allotted time.

Jan 4, 1977

By Edward D. Thimons, Richard J. Kline

Converting the energy of falling water into useful work is a well developed engineering concept. Much of the electric power consumed in the United States is generated in this manner. It is easy to conceive that the water which flows down long vertical pipelines into deep nines could be utilized in a similar manner by allowing it to operate a turbine at the bottom of the pipelines. The mines in the United States are continually descending to greater depths in search of mineable deposits. Large quantities of water are carried down long vertical pipelines in order to be used for dust suppression, motor cooling, and refrigeration. Pumping the used water back to the surface is also required. The electrical costs associated with mining are also constantly escalating due to both increased demand and rising kilowatt hour costs. To help deal with this problem, the United States Bureau of Mines (USBM) has awarded a contract to Foster-Miller, Inc. of Waltham, MA, to investigate, evaluate, and demonstrate commercially available means of energy recovery for the deep mining industry. In other words, it demonstrates an efficient system for converting the energy of water flowing down vertical pipelines into useful mechanical or electrical energy.

Jan 1, 1982

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By Robert Archer

IT is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a, salt flux of which the, active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification' and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Company of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible

Jan 2, 1926

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk' also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956

By George M. Fowler, F. E. Gregory, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By William M. Agar, F. E. Gregory, Joseph P. Lyden, George M. Fowler

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By F. E. Gregory, George M. Fowler, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By Joseph Gurland

EVERAL carbide-cobalt compositions were pre-^-5 pared for the purpose of determining the transverse rupture strength of various carbide-binder systems. The binder content was held at 10 and 37 volume pct Co, so as to be representative of low and high bjnder compositions. The carbides used, WC, Tic, TaC, CbC, VC and ZrC, were selected on the basis of availability, knowledge of their properties, and small solid solubilities in the binder metal at room temperature. The methods of preparation and carbon analysis of the carbides are summarized in Table I. The carbides with cobalt added were ball milled, pressed, and sintered. vacuum sintering was used throughout, except for the WC-Cs alloys, which were sintered in hydrogen. The sintering temperatures ranged from 2500" to 2750°F for the low binder alloys and from 2300" to 2550°F for the high binder alloys. Compositions and properties of the sintered com- pacts are presented in Table 11. For the transverse rupture strength, the average and range of the five best samples of each alloy are listed. Discrepancies between the actual and theoretical densities are attributed to carbon deficiencies in some samples. The theoretical densities were calculated by assuming mixtures of carbides of stoichiometric compositions and cobalt. Representative microstructures are shown in Figs. 1 to 6. The porosity was A-2 or better' in all alloys except those with ZrC. A grain size of about 3 p was

Jan 1, 1958

By Frank Milliken

IN September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1007 to 1019. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was dissemi-nated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was prob-ably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a com-plete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof com-prised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. 1, which gives percentages of tonnage and copper content.

Jan 1, 1940

By AIME AIME

LIFE in few countries is dominated by geographic conditions to the degree that it is in Peru. The broad plateau of the Andes, bordered by lofty ice-clad ranges with deeply eroded flanks, imposes a pattern on the region to which most human activities must conform. On the Pacific side, desert conditions prevail, interrupted only by irrigated valleys along rivers that descend from the highlands. Above seven or eight thousand feet the rocky ridges become grass covered, and the central zone is one of high pastures with cultivation in the valleys or on terraced slopes except at altitudes over 15,000 ft. where glaciated landscapes prevail. Each of the three belts has its own distinctive resources and climate, and each its own special ways in which its inhabitant, must make a living. The Pacific region is one of the most arid regions in the world. Except for the irrigation, the country is an unmiti¬gated desert. The climate, in spite of the tropical latitudes, is mild with the heat relieved by air from the adjoining cold ocean. Fogs are prevalent throughout the winter months but precipitation is scarcely measurable. Ideal conditions exist for cultivation of sugar and cotton which are the dominant crops. Lima, the capital. situated in one of the most productive valleys, is an impressive city which in its modern development is well maintaining the high position it held when it was the

Jan 1, 1945

By Frank C. Smith

The following article covers the history of a metallurgical campaign, commenced in March, 1905, at the mines of the Socorro Bold Co., in the so-called desert region of Yuma county, Arizona. The results obtained were simply a function of necessity, as will be seen from the description of the local economic conditions and the character of the ores treated. The mines and mill of the Socorro Gold Co. are located near the small village of Harrisburg, about 60 miles from Congress Junction, Ariz., which, at the time this work was undertaken, was the nearest railroad station, and from which all supplies were brought by wagon through the desert, at a cost varying from $10 to $15 per ton in addition to the railroad freights. Wood, the only available fuel, cost $7 per cord. Water for all purposes was pumped to the plant from a well in the valley about 4 miles away. Under the Arizona law, a working-shift is 8 hr. Wages were $6 per day for foremen and mill-men, $4 per day for blacksmiths and engineers, $3.50 per day for miners, and $3 per day for shovelers and trammers. The ore consisted of quartz, in which, above the 250-ft. level, the iron-minerale were largely oxidized and some free gold was visible; below that level few traces of oxidation occurred, and pyrite constituted the principal mineralizer in the quartz, together with occasional pockets of galena and a few eccentric specks of covellite. The 20-stamp mill was equipped with plates for amalgamation, and three Standard tables for concentration. The tails from the tables mere elevated by a centrifugal pump to a launder, by which they were conveyed to a 60-ton cyanide-mill for further treatment. The cyanide-mill was erected at so great a distance from the stamp-mill that a separate crew of workers and a separate power-plant were necessary. No arrangement had been made for the treatment of the concen-

Jan 1, 1907

By ROBERT E. HARDWICKE

THE QUESTION of whether the production of oil should be limited to market demand has been constantly discussed during the last two years. Oil men, legislatures and courts have reached highly conflicting conclusions. Opponents of limitation to market demand assert that it is a scheme of the big purchasing companies to fix prices and to create a monopoly. Proponents, on the other hand, declare that such a limitation is necessary to prevent physical waste and that the effect on prices is merely incidental. A brief review of market demand legislation will disclose the confusion existing. The laws of Oklahoma,' prohibiting waste of oil and gas, specifically' authorize limitation to market demand as a method of preventink such waste. These laws and the proration orders based thereon have been upheld by the Supreme Court of Oklahoma, by several three-judge Federal District Courts, and by the Supreme Court of the United States.' Kansas has a similar law3 but no case has been found which discusses its validity. About a year ago the California Legislature passed a comprehensive conservation act, generally known as the Sharkey Bill giving authority to restrict production to an amount representing current requirements for use, taking into consideration oil and products in storage. This may be considered as equivalent to limitation to market demand. The Act was defeated upon referendum vote after a hard fought campaign in which it was charged that the Act would result in destruction of the independent operators.

Jan 1, 1932

By W. C. Meyer

In an effort to conserve and extend oil resources, the use of powdered coal-in-oil mixtures (COM) as an alternate fuel in oil-fired boilers is receiving increasing attention. For the approach to be successful, some degree of stability of the suspension against settling is needed. The variety of means available to achieve stability of this nonaqueous slurry is reviewed along with some of the physical and chemical concepts which underlie each method.

Jan 1, 1983