Search Documents

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not with-stand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these require-ments, but as a result of the extensive research carried on by steel manu-facturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham', Eckel' and others .' However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger' led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

By J. L. Huitt, B. B. McGlothlin, D. K. Lowe

Published correlations for the principal aspects of hydraulic fracturing were combined into a digital computer program to facilitate the study of interrelated variables. The computer program includes individual relationships for fracture width during pumping, fracture area generated, propping agent embedment, flow capacities of propped fractures and transport of propping agents in horizontal fractures. The effects of more than 20 treatment and formation parameters on the predicted results of hydraulic fracturing treatments were studied. The effects of these parameters were determined for (I) fracture width during injection, (2) fracture width after the overburden comes to rest on the propping agents, assumed not to be crushed, (3) generated and propped fracture area, (4) location and concentration of propping agents in the fracture when injection ceases, (5) flow capacities of the various propped sections of the fracture and (6) expected increase in the well productivity. The effects of propping agent, formation and fracturing fluid parameters on well productivity are discussed. The parameters that were found to have the most pronounced effects on hydraulic fracturing treat~nents are injection rate, treatment volume, fracturing fluid coefficient, size and amount of propping agent, spearhead volume, well drainage radius and formation capacity. INTRODUCTION Many correlations have been published for predicting effects of various parameters that are considered in the design of hydraulic fracturing treatments. The Carter equation' can be used to predict generated fracture radius as a function of fracture width, fracturing fluid leakoff and other parameters. Fracture width can be determined by use of the Perkins and Kern correlation' in which the fracture width is related to the fracture radius, fluid injection rate and certain formation and fracturing fluid parameters. Wahl and Lowe et aL4 have reported methods of predicting the location of propping agents in fractures when pumping ceases. The former study is applicable to the case where the ratio of propping agent diameter to fracture width is less than 0.1. The latter is applicable when this ratio is greater than 0.1. These studies showed that the propping agent placement in horizontal-radial fractures depends principally on how the individual particles are transported in the fracture by the carrying fluid. Particle transport in fractures is determined by local fluid velocity in the fracture, fluid and particle properties, and the size of the particle relative to the fracture width. The distribution of propping agents, effective overburden pressure and formation rock strength control the propped fracture width6 by controlling the extent to which the propping agent particles embed into the fracture faces. From the distribution of propping agents and the propped fracture width, fracture flow capacities can be calculated or the various regions of the fracture. The flow capacities and the radial extent of these regions can be combined with reservoir information to predict the productivity increases for fractured wells. In all these studies, the effects of certain treatment and/ or reservoir parameters on one facet of fracturing can be predicted only if other facets which the parameters affect are fixed. For instance, fracture width and radius are interrelated; that is, to calculate the value of one, the value of the other must be known. Also, some parameters influence more than one aspect of fracturing. For example, prop-pant transport is a function of both fracture width and fluid viscosity. but fracture width is itself a function of fluid viscosity. Since these calculations are complex and the parameters interrelated, it is not possible to write an equation with which the over-all effects of treatment parameters can be solved explicitly. For these reasons, the correlations for determining the effects of the parameters which are most significant in hydraulic fracturing treatments have been incorporated into a digital computer program. COMPUTER PROGRAM The program, which was written for an IBM 7094 computer, can be used to predict results of most of the combinations and values for the treatment parameters that are ordinarily considered for fracturing treatments. A spearhead of fracturing fluid and a propping agent-carrying fluid with different fluid properties can be taken into account. Also, the total volumes and relative amounts of the spearhead and carrying fluids can be varied. Two different propping agents (as used in tail-in operations) and a wide range of formation properties and injection rates are considered. The computer program (Fig. 12) consists of several sets of calculations. First, the final flooded fracture radius and average fracture width at the cessation of pumping are calculated. This is done by simultaneous solution of the Perkins and Kern fracture width equation and the Carter equation for flooded fracture radius (equations used in the computer program appear in the Appendix). The next step is to determine local fluid velocity in the fracture as a function of time and radius. Since it is not possible to write this function in closed form expression, a table of velocity values is generated by the program and stored for subsequent use. The time span from the beginning of

By O. C. Ralston, William C. Hunter

DUring experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent. zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 Ib. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: Per Cent. Per Cent. Oz. peR Ton Cu............... 0.695 Al2O3............ 0.83 Ag................. 1.30 Zn............... 6.17 S................ 43.35 Au................ 0.02 Fe...............36.23 CaO............. 0.46 SiO2............. 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: Per Cent. Per Cent. Chalcopyrite................... 2.0 Schist........................... 3.2 Marmatite..................... 10.32 Quartz........................... 8.2 Pyrite........................ 73.0 Calcite.......................... 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as to render impossible the preparation of commercial grades of concentrate.

Jan 1, 1930

By L. B. Slichter

After statement of the principles of similitude which apply to electromagnetic modeling, charts showing the inductive response of conducting spheres as dependent upon frequency, conductivity, and size are exhibited in this paper. The shape of the curve which relates intensity of response to frequency is significant in indicating the advisability of low frequencies in the exploration for conducting bodies, when consistent with the securing of a large percentage of the ideally possible response. Comparisons of theoretical response and that observed with models are shown, and relationships with the subject of applied electromagnetic prospecting are indicated. Maxwell Field Equations The Maxwell field equations summarize the physical laws that govern electrical field phenomena; they are the basis for the solution of electromagnetic problems. These concise equations, with adequately formulated boundary conditions, specify the complete electrical condition of continuous media, and the development of their solution amounts merely to a more convenient re-expression of phenomena already completely described. Thus, the immediate content of the field equations themselves is sufficient and sometimes convenient for the treating of certain questions (such as those relating to electromagnetic models) which are independent of the special factors of geometry, or the nature of an impressed field. The four Maxwell field equations are written below, in c.g.s. gaussian units: curl E = -B/c [21 div eE = 4pp [31 div B = 0 [41

Jan 1, 1932

By S. L. Lopata, E. B. Kula

A variation of yield and tensile strength with direction has been noted in heat-treated 4340 steel which had been warn-worked by rolling in the austenitic condition prior to quenching. Measurements by X-rays showed a preferred orientation of martensite crystals. Various ideal preferred orientations of martensite were calculated by assuming a preferred orientation for austenite and transforming this to martensite by the Kurdjumov -Sachs and Nishiyama relationships. Comparison with the measured preferred orientation showed that the ideal rolling texture for austenite in 4340 steel could be expressed as a (112) [111] texture with a component of (110) [112]. No evidence was found for any fiber axis in the rolling direction, or fop- a (123) [412] texture. The observed martensite pole figures can be adequately accounted for by these ideal austenite textures and by the Kurdjumou-Sachs or Nishiyama transformation relationships between austenite and martensite. ALTHOUGH preferred orientations are found in cold-rolled steel sheet and in many nonferrous metals, they are not generally encountered in wrought, heat-treated high-strength steels, since such steels are generally not cold worked sufficiently to develop a strong texture, and any texture that is present is removed during heat treatment by the phase transformations taking place. This report gives details on a preferred orientation found in warm-rolled and hardened 4340 steel. In a recent study, a special combination heat-treating and working technique was used in which 4340 steel was deformed in the austenitic condition, and before re crystallization of the austenite could occur, quenched to form martensite.' Since the austenite was unrecrystallized, it was cold worked and hence could have contained a preferred orientation which could be transmitted to the martensite on quenching, and this in turn could be manifested as a directionality of mechanical properties. Such a directionality of properties was found as a result of working, and this prompted an X-ray study of the preferred orientation. Literature Survey— Rolling Texture in Face-Cen-tered-Cubic Austenite—M a preferred orientation is found in a rolled and hardened steel, it is first appropriate to consider what texture existed in the austenite as a result of the rolling but prior to the transformation to martensite. The changes taking place as a result of the austenite-martensite transformation are then considered. In view of the instability of austenite in 4340 steel at low temperatures, no direct determination of the austenite texture was made. However, an estimate of the texture for austenite in 4340 steel may be made by considering the textures found for other face-centered-cubic metals. Barrett' has reviewed the rolling textures for many materials. The most common orientation in face-centered-cubic metals has the (110) planes parallel to the rolling plane and the [112] directions parallel to the rolling direction, or (110) [112]. Other orientations found are (112) [111], as well as (100) [001], (110) [001], and others. Beck and his co-workers, using quantitative pole figures, report that (123) [121],3 later corrected to (123) [412],4 better describes the ideal orientation. smallman5 reported that the ideal preferred orientation for high-purity face-centered-cubic metals is (123) [121], but that there is a transition to (110) [112] as solid solution elements are added. The latter texture tends to occur more readily at lower temperatures. This transition between the two textures was explained by differences in the slip characteristics with concentration or temperature. More recently, Jones and Fell6 concluded that the (123) [412] texture for face-centered-cubic metals could equally well be represented by a mixture of (110) [112] and (112) [111] textures, and hence it had no physical reality. From the above results it can be seen that there is no agreement on the "ideal" texture for fcc metals and, hence, no firm basis for assuming a texture for austenite in 4340 steel. Therefore, the orientations (110) [112], (123) [412], and (112) [111] have been considered in the following.* *The (123) [4121 is identical to the (123) [121] rotated 90 deg. Orientation Relationship between Austenite and Martensite—When martensite forms from austenite, certain crystallographic planes of the martensite are parallel to planes in the austenite. This orientation relationship was first determined by Kurdjumov and

Jan 1, 1960

By C. W. Clark, J. H. Schloen

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,1 written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. EARLY SILVER-REFINERY OPERATIONS From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700° F. in a Nichols-Herreshoff furnace, acid¬leached with tankhouse discarded foul electrolyte (20 per cent H2SO4), filtered and charged directly to the doré furnace for refining to doré metal. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1938

By Adrien Berton

FOR nearly a century, the Corocoro deposit has been renowned among geologists from the fact that it shares with the Lake Superior deposits of the United States the distinction of being the only important copper districts where native copper is worked commercially. The Corocoro district, named after the city of Corocoro, the capital of the Province of Pacajes (Department of La Paz, Bolivia) is situated towards the western edge of the Bolivian high plateau, at an altitude of a little over 13,000 ft. The most interesting part of the district is that immediately surrounding the city of Corocoro, at a distance, by railway, of 65 miles from La Paz and 210 miles to the Chilean port of Arica on the Pacific Coast. The climate of the region is that of the semi-desert, dry and relatively cold, with big differences of temperature between day and night. The rainy season begins in December and ends in March. The cupriferous lodes of Corocoro have not attracted as much interest as the silver mines of Potosi but they have been known for a long time. In the precolonial period the Indians were using the charquis, or natural native copper sheets, to make small brass objects, and the beautiful pale green brochantite of the outcrops as a source of green pigments. During the colonial period, the oxidized ores of the outcrops were worked for copper, which was used by the mint at Potosi for making currency. The native copper ores were neglected because the Spanish miners were at a loss how to concentrate and smelt them. About 1830, work by rudimentary processes, which were improved little by little, was begun on the native copper ores. The total production of native copper in the following hundred years amounted to 100,000 tons. This native copper, which was remarkably pure, was much appreciated on the European markets before the introduction of electrolytic copper. It was useful for making special ornamental brass or bronze and the granular concentrates of native copper, called barrilla, containing 80 to 85 per cent copper were suitable for making copper sulfate by direct oxidation and subsequent leaching with sulfuric acid.

Jan 1, 1936

By R. J. Brown

Design of a submarine pipeline system is governed by many factors, one of which is the effect of transverse horizontal currents on the pipeline structure itself Although this feature alone can be of utmost importance to the life span and stability of the underwater pipeline, it is usually the least recognized, with these hydro-dynamic forces being either completely overlooked or grossly underestimated. In an attempt to supply the methods and means for stabilization of sub-marine pipelines, much capital has been spent by pipeline companies. Design criteria incorporated by these organizations extend over a broad spectrum of engineering with bases varying from pure theory to cut and dry methods. A history of numerous failures has substantiated the postulate that many of these submarine pipelines have been underdesigned from the stability standpoint. By the same token, equally as many have been excessively overdesigned with resultant excess expenditures. An attempt has been made in this paper to establish the magnitudes of these hydrodynamic forces by measuring the lateral current-induced differential pressure distribution around the periphery of the submarine pipeline. INTRODUCTION The expenditure of money for research by corporations obviously requires beneficial results to justify the investment. One of the functions of the engineer is first to make the problem known and then to provide a means of solution at the least possible cost. The initial procedure is to investigate all pertinent published technical articles on the subject to determine if this problem has been previously solved. If resolution of this problem is not obtainable, the next course of action is to evaluate through experiments these forces and their magnitudes. On the specific subject of drag and lift, the accumulation of data is provided from three separate and distinct sources: from experience, from theoreticians and through experimental observations. The experience source has proved costly with money wasted either because of underdesign and failure or excessive expenditures for overdesign, and has not been sufficient to form a definite conclusion on these hydrodynamic forces. The pure theoretician is often not completely cognizant of the situation and his works bear little adaptation to the real problem. The experimentalist has his own problems with regard to obtaining results from small-scaled models and successfully adapting them to the larger prototypes. Each method has its own advocates who diligently adhere to their own separate routes as being the only means of resolving this problem. However, a review of the various methods of analysis leads one to the conclusion that if the advantages of all three are combined, a reasonable solution to this problem can be reached. Briefly then, the problem is to obtain the magnitudes of the forces on the submarine pipeline subjected to a lateral current by investigations of previous design considerations, by a study of existing theoretica1 data and by appropriate experimentation. This paper deals mainly with obtaining experimental data and the interweaving of theoretical and experience factors for resolution of these forces. APPARATUS AND PROCEDURE These tests were performed in 1961 at Collins Construction Co.'s main office near Port Lavaca, Tex. Test equipment consisted of a steel tank 3 ft high by 4 ft wide by 40 ft long, with several pumps circulating the water through the tank via suction lines from the downstream portion of the tank and discharging from the pumps directly into the upstream end of the tank. For reduction of turbulence, a wire section was constmcted in the upstream portion and straightening vanes in the form of pipes, screens, etc., were used to reduce the vortex and eddy action in the tank (Fig. 1). A venturi was built at the test specimen for obtaining velocity sufficient to simulate actual conditions. This full-scale test was initiated to eliminate the error introduced in modeling and obtain a truer picture of forces actually encountered. Six- and 10-in. specimens were prepared by

Jan 1, 1967

By J. L. Taylor, P. Duwez

The phase boundaries in the ternary system Ti-Cr-Al have been established at 1800° and 1400°F for alloys containing more than 60 pct Ti. The martensite transformation temperature has been measured for the titanium-rich alloys. THE studies of binary alloys of titanium with the transition elements which have been published so far1-0 ndicate clearly that the solubility of these elements is always much greater in the high temperature body-centered cubic form of titanium (ß phase) than in the low temperature hexagonal form. In this category of alloying elements are iron, nickel, chromium, manganese, vanadium, molybdenum, tungsten, columbium, and tantalum. Although studies of the nontransition elements have been rather limited, early work on titanium binary alloys'" has shown that most of them were not very soluble in the a form, with the exception of aluminum, for which the solubility in a is about 25 pct.13, 12 In addition to this large solubility in a, aluminum is also soluble in ß titanium to the extent of about 35 pct and the transformation temperature from ß to a is raised with aluminum content. This effect is also typical of aluminum, in contrast with that found for the transition elements which lower the ß to a transformation temperature. Therefore, it may be anticipated that tprnarv titanium alloys with aluminum and any one of the transition elements will constitute a class of ternary alloys having characteristic features absent in alloys involving two transition elements. Chromium was chosen as a typical transition element for the present study because ternary alloys of Ti-Al-Cr commercially produced have been found to possess very interesting physical properties (MST-3 pct A1-5 pct Cr of Mallory-Sharon).'" Binary Systems The binary systems Ti-A1 and Ti-Cr have been established recently by several investigators. The data used in this investigation were taken from the complete diagram of Bumps, Kessler, and Hansen." This diagram agrees quite well with earlier investigations." For the Ti-Cr system, the phase boundaries at 1800" and 1400°F were taken from refs. 6 and 7. The binary system Cr-A1 has been studied recently by Bradley." This system is rather complex and contains not less than seven intermediate phases. The present study was limited to the titanium corner of the ternary system (less than a total of 40 pct Cr plus Al) and none of the phases present in the Cr-A1 binary alloys were found in the ternary alloys investigated. Experimental Technique Microscopic observation and X-ray diffraction measurements were used to identify phases and de-

Jan 1, 1954

By Robert T. Howard, Morris Cohen

THE purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature trans- formations have been summarized recently by Troiano and Greninger.1 Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation [(M,)] during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transfoi mation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metallographic3 and dilatmetric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Steward7 have shown that the Greninger-Troiano metallographic techniques may be used not only for [M,] determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below [M,] in fourteen commercial steels. In the present paper, the Greninger- Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M,, thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. EXPERIMENTAL DETAILS Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M, temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1947

By F. R. Brotzen, J. Taranto

SEVERAL investigators have computed stacking-fault concentrations from X-ray diffraction data.'-' The method generally employed relates the line shift to the stacking-fault probability. In this investigation platinum filings of 99.99 pct purity screened to -325 mesh were studied after having been subjected to various annealing treatments. The lines were measured on a General Electric XRD-5 spectrogoniometer using CuK, radiation. The centroid of the broad reflections was determined by the method proposed by pike.' The stacking-fault probability was calculated by the formula given by Warren and warekois,3 with the assumption that all stacking faults were on the (111). Various high-angle reflections were used, but most data collected refer to the shift in the (400) reflections. When the filed platinum powder was annealed at 1200°C for 20 min the stacking fault concentration was too small to be detected. The stacking-fault probability in freshly filed specimens, as determined by the line shift relative to the annealed specimen, was about 0.016, Fig. 1. If the faults would be created only by extended dislocations, the dislocation density in the filed specimen would be about 3X1012 cm-2. The average stacking-fault width of about 21 which was used in this computation, is that given by Thornton and Hirsch.7 The mechanism by which stacking faults are annihilated during annealing is not yet fully understood. The isothermal results obtained do not seem to support the simple hypothesis of a first-order decay. On the other hand, the analysis by Kuhlmann, Masing, and Raffelsieper8 for the loss of dislocations during recovery agrees much better with the experimental data of this investigation. This analysis yields an activation energy of 29 ± 8 kcal per mol for the disappearance of stacking faults in cold-worked platinum during annealing. Even if one takes into account the lack of accuracy inherent in this X-ray method, the activation energy found is substantially less than that of self-diffusion in platinum, i.e., 61.6 kcal per mol.9 The results therefore suggest that processes other than dislocation climb, which involves the activation energy of self-diffusion, are responsible for the loss of stacking faults in platinum during annealing. The broad reflection lines became sharper early in the recovery process, Fig. 1. The sharpening occurred well before the stage during which stacking faults disappear. This lends support to Nowick's10

Jan 1, 1962

By A. B. Bowman

The 1963 Jackling Award lecturer describes the founding of Banner Mining Co. and its trials and tribulations before becoming an established firm. Such aspects as geological description of Banner mining areas, history of exploration and production, areas of present interest to the company and research work conducted by the company are included. Several years ago a wealthy Chinese business friend of mine purchased an interest in a proposed oil well to be drilled a great distance from his home. A few months later it came in as a producer and proved to be a huge success and materially added to his resources. I asked him why a man of his wealth should be so lucky in a venture outside his sphere of knowledge when most people of modest means never seemed to get ahead. His answer was, "Fat Hoy takes a chance." Even though this was his answer, I knew from my association with him that there were other tempering considerations which Mr. Hoy applied before making up his mind to enter any transaction. First, he was a cautious individual. He was also a great believer in details and insisted on knowing everything possible about a situation, and finally, he was what we call a very solid individual with good basic instincts and judgment. This philosophy of Mr. Hoy may be applied to most any business but especially to those engaged in a search for natural resources such as mining where great risks are involved. This article concerns events in the history and growth of Banner Mining Co., with which I have been associated for 27 years in capacities from mine surveyor to vice president. Mr. Hoy's philosophy has played a significant role in the exploration projects of this company over the years, but what is more important, the officers, directors, and controlling interests in Banner have been aggressive in their search for ore reserves. THE BIRTH OF BANNER Banner Mining Company was incorporated in September 1935 by a group of Oklahoma and Texas oil men for the purpose of exploring and developing the Bonney-Manilla mines at Lordsburg, N.M. These properties had a history of intermittent production since the first ore discoveries as far back as 1870. Most of the production from the district has come from four mines, namely, the Eighty-Five, the Atwood, the Bonney-Manilla, and the Misers Chest. The last two are now owned by Banner Mining. The Eighty-Five mine operated between 1885 and 1931, and production totalled 1,494,287 tons averaging 0.11 oz of gold per ton, 1.23 oz of silver per ton, and 2.80% copper. The vein extended for a distance of about 3000 ft northeast and was mined to a depth of 1650 ft. The Atwood mine, adjoining the Eighty-Five mine, to date has been of lesser importance as a producer, but it has been operating for several years producing high silica flux ores for a smelter. Production totalled 352,828 tons up to January 1, 1962 From the Bonney-Manilla and Misers Chest mines, owned by Banner, production through 1961 totalled 2,006,343 tons with an average grade as mined of 0.0192 oz of gold per ton, 0.760 oz of silver per ton and 2.63% copper. Banner built a 150-tpd flotation mill in 1936 after almost a year of development on the 600 level of the Bonney mine. After less than one year's operation, it became apparent that the 150-tpd rate was not sufficient to make a reasonable profit due to the marginal grade ores. The low tenor of the ore, mainly chalco-pyrite in a highly siliceous gangue, made mandatory the close control of costs in order to make ends meet. A 300-tpd unit was added to the mill in 1937, and it is still the operating unit today. The clean sulfides presented no problems in milling. A metallurgist doing research on it at the time stated that the copper minerals seemed to have a built-in desire to float. Mill recovery of copper throughout the 27 years of operation has averaged 96.23%. A PERIOD OF FORCED GROWTH World War II brought many hardships to Banner. Labor and supply shortages caused drastic curtailment in development work. Rapidly rising costs far outdistanced any relief from pegged prices which we received from Government agencies. Finally, a branch of the Government asked us to stop all devel-

Jan 1, 1963

By J. Ruzicka

IN creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently bear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addi-tion to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabri-cated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment.

Jan 1, 1937

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

By L. F. Bishop

The ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill is a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various methods in use for the second six months of 1944 are shown in Table I. This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1946